CA NO GE(H)-21/2024-25 SPECIAL REPAIR TO BLDG NO T-122, T-125, T-126, T-131, T-132, T-133, T-173, T-174, T-175, T-176, T-513, T-515, T-516, T-517, T-512, T-514, T-509, T-141, TL-69, TL-216 IN THE AOR OF AGE B/R-I UNDER GE HISAR AT HISAR MIL STN

Amount

Taking down chowkat or frame with shutters area not exc. 1.5 Sqm each (without taking off the wooden shutters from the frame) including making good the hold fasts notch / disturbed portion complete all as specified

Taking down chowkat or frame with shutters area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the wooden shutters from the frame) including making good the hold fasts notch / disturbed portion complete all as specified

S&F for factory made Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening & making good the plaster of wall In CM 1:6 as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat 2 mm thick moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified & directed.

S&F pressed steel frames of size 105mmx60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed Note :- Rates quoted deemed to include S&F of hinges, lugs, lock strike plate.

Supply and fixing factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles, fixed to chowkat, complete all as specified & directed.

S&F factory made Steel windows, ISI marked, (Box Type) with side hung shutters including box type hinges with steel handle etc complete with glazing bars dovetailed or welded including one shop coat of Zinc chrome primer including making good disturbed surfaces of walls, complete Notes:- (i) The rate quoted by the contractor are deemed to be included for one shop coat of red oxide zinc chrome primer on steel windows. Nothing shall extra paid on this account. (ii) Glass pane/wire gauze shall be measured and paid separately.

S&F factory made Steel windows, ISI marked, (Box Type) with side hung shutters including box type hinges with steel handle etc complete without glazing bars dovetailed or welded including one shop coat of Zinc chrome primer including making good disturbed surfaces of walls, complete Notes:- (i) The rate quoted by the contractor are deemed to be included for one shop coat of red oxide zinc chrome primer on steel windows. Nothing shall extra paid on this account. (ii) Glass pane/wire gauze shall be measured and paid separately.

S&F steel ventilator with top hung shutterof glazed & gauged including hinges, steel peg stay, with glazing bars & handle including one shop coat of Zinc Chromate primer complete all as specified.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified and directed.

M&L for PCC 1:2:4 type B0, using 12.5mm graded crushed stone aggregate as in filling up chowkat , hold fast, bed block and similar works as directed, complete, all as specified.

Supply and fixing 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified.

S&F in repairs galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple complete all as specified.

Supply & fixing butt hinges of size 100mm medium weight, cold rolled mild steel ISI marked complete all as specified.

S&F 250mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified

S&F 200mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified.

Supply & fixing aluminium handle 150mm size cast type, anodized complete all as specified.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs / blankets any thickness, including cover fillets complete all as specified

S&F Anodised aluminium snap grid size 605 x 605mm frame work for false ceiling including hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified.

S&F Gypsum board 9-12mm thick duly finished surface (thin PVC layer on gypsum board as per maunfacturer's instructions) of size 595mmx595mm thick and the same shall be placed in snap grid as in false ceiling complete all as specified and directed. Note : The snap grid frame work shall be measured & paid for separately

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thickness (below or above ground level.) & removing unserviceable materials in low laying area, complete, all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises.

Material and labour 50 mm thick PCC (1:3:6) type C2 using 40 mm graded stone aggregate as in plinth protection, surface finished fair and even without using extra cement complete all as specified.

M&L for non skid ceramic jointless digital tiles (coloured) 1st quality, 7 to 8mm thick, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for non skid ceramic jointless tiles (coloured) 1st quality, 7 to 8mm thick, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for non skid ceramic jointless tiles (coloured) 1st quality, 7 to 8mm thick, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:3 complete all as specified and as directed.

M&L for glazed ceramic tiles (coloured) 1st quality, 200mm x 300mm x 7mm thick, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

S&F in repairs vitreous china wash down water closet (Padestal pattern) White, including plastic water closet seat cover, black, closed pattern with flat bottom with mild steel chromium plated or aluminium hinging device and fixing with all joints including connection to drain or outgoing pipe and to flushing pipe, anti-syphonage pipe etc complete all as specified and as directed.

S&F in repairs 15mm bore, fancy type brass CP Hand Shower (Health Faucet) (ABS Body) with 8mm Dia, 1.2 Meter Long Flexible Tube & Wall Hook confirming to cat No BEA 85 of prayag or techno commercial equivalent complete all as specified and as directed.

S&Fin repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, 'P' or 'S' trap, including connection to trap and flushing pipe, antisyphonage pipe etc including provision of PCC (1:5:10) type E2 in filling, making good to floor, complete all as specified.

S&F in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified.

S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore PTMT waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified.

Taking up or down 20mm bore steel tubing and connection incl cleaning for refixing or removal to store

M&L galvanized steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed

Dismantling old unserviceable PVC water tank capacity 250 ltr and not exc 500 ltrs & removal from site etc complete all as specified and directed.

S&F in repairs 15mm bore stop valve, fancy type , chromium plated cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed all as specified and directed.

S&F in repairs Bib taps,cast copper alloy with crutch or butterfly handle, chromium plated, fancy type , screwed for iron pipe or for brass ferrule, for 15 mm bore GI pipe complete all as specified and directed.

S&F in repairs, PVC connection 450 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

S&F in repairs PVC (SWR) floor trap 75mm dia, plain with grating including joining to waste pipe, all as specified and directed

Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks (colour other than black as approved by Engineer-in-charge) triple layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20mm bore (minimum weight 210 gms) complete all as specified and as directed.

S&F in repairs 20mm bore PTMT nipple suitable for PVC tanks (minimum weight 45 gms) complete all as specified and as directed.

S&F in repairs Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 20mm bore.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints fixed to walls with necessary MS / PVC clamps and necessary screwing complete all as specified.

S&F 110mm PVC (SWR) junction single, (Single T) equal or unequal provided with access door complete all as specified and directed.

Supply and fixing 110 mm bore PVC (SWR) vent cowl complete all as specified.

S&F PVC (SWR) 'P’ trap 110 mm bore complete all as specified & as directed.

S&F PVC (SWR) Gully trap 125/110mm, setting and jointing with solvent cement complete all as specified.

S&F salt glazed stone ware drain pipes of 150mm bore, grade `A', ISI marked, laid to slope in trenches, jointed in CM (1:1) and tested complete all as specified

S&F 150mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified & as directed.

Material and labour for PCC 1:3:6 type C-2 using 40 mm graded crushed stone aggregate in bedding to SGSW/RCC drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.

Demolition of brick/stone masonry built in cement/lime mortar of any mix and stacking serviceable stones aside for reuse & removing unserviceable materials in low laying area, complete, all as directed.

M&L for brick work using old size fly ash bricks as specified in clasue 6 of Particular specification, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified.

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed.

M & L for rendering 10mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces of walls, finished even and smooth without using extra cement complete all as specified.

Material and labour preparation of newly plastered surface of walls & applying three coats of white wash complete all as specified

M & L for rendering 15mm thick in cement mortar 1:4 on faces of brick work or concrete surfaces of walls, finished even and smooth without using extra cement including mixed with and including liquid water proofing compound @200 ML per 50 KG by weight of cement complete all as specified and directed.

Supply only integral liquid water proofing compound (ISI marked).

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint on walls over a coat of primer all as specified & as directed.

M&L for preparing the old decorated plastered /un plastered surfaces of walls including cornices by brooming down or steel wire brushing scrapping down or steel wire brushing scrapping down smoke soot etc. and applying one coat of cement base paint of approved shade/tint on wall surface to give uniform and smooth surface etc complete all as specified and as directed

M&L for preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint all as specified & as directed.

Dismantling AC sheet (Corrugated, Semi corrugated etc) as in roofs etc complete all as specified.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified & directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified & directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for in this Schedule all as specified & directed.

S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, necessary welding etc. conforming to Gde E-250 (Fe 410-W) quality `A’ ISI marked (IS-2062) all as specified and as directed.

S&F 15mm bore fancy type pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes & fly nuts, screwed for iron pipes all as specified and directed.

Excavation over areas not exc 1.5m deep and getting out in soft/loose soil all as specified and as directed.

M&L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface all as directed.

M&L for 100mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified

M&L for 100mm thick PCC 1:2:4 type B2 using 40mm graded crushed stone aggregate as in flooring as directed) all as specified and as directed.

Removing excavated surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point etc complete all as specified and directe.

malik constructions

NAVIN KUMAR

M/S RAJESH KUMAR & SONS

M/S KAVITA CONSTRUCTION

m/s krishna engineers1

OM CONSTRUCTION CO.

Siya constructions