Design, Fabrication, Supply and Installation of Signage and Graphics for Twelve (12) Underground Metro Stations of Reach-6 under Phase-II.

Design of Detailed sign plan, layout, Graphic and Fabrication for each station separately as per the typical drawings and as per the approval of Engineer. This includes the customization of standard signage for each station based on historical or commercial importance of site, interchange and including content design for LED Display system. The Design consultant has to have experience in Design of signage & Graphic for Metro/Airports. The rate includes the Design, Mock Up, Samples and working Models, Etc., Complete.

Interior Illuminated sign double sided Suspended, Projected, Post mounted. Drg. No.1.1.2 a, b. Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per relevant drawings, technical specifications, signage schedule etc complete all as specified as under. Sign Box: The sign box 110 mm deep shall be fabricated out of 1.6 mm thick CRCA MS sheet and reinforced with spot welded inverted hat section for entire length at top and bottom and connected with couple of ties at a max spacing of 750 mm. Parts will be laser cut blanks bent and assembled with spot and CO2 welding. Joints/welds shall be minimized on account of continuous channel bent at corners facilitating maximum dimensional accuracy and repeatability. Sign box shall be provided with a ventilation fixture with Mesh from inside for ventilation confirming to IP54. Complete sign box including channel supports are to be powder coated to match GreyG1. Sign box flange receiving the sign face shall be provided with slots to receive the screws to fix the sign frame. Sign panel - Both faces: Providing and fixing sign panel on 1 side of sign box made out of 1.6 mm thick CRCA MS sheet frame fabricated to required size and shape, the frame shall be welded on 2 bottom corners making a 'L' and top part of frame fixed at site after inserting the sign face, complete frame shall be powder coated on all faces to match GreyG2. Sign face shall be made in 8 mm thick Opal white acrylic (as specified) having graphics pasted in Plotter cut Block out vinyl pasted over a translucent white vinyl and entire panel covered with a protective over laminate. The films to wrap around the edge of the acrylic to a distance of 25 mm on the back side. The Plotter cut block out vinyl shall match the specified colour (colour Pantone 2766 and Pantone 667C) and of specified make duly approved by the Engineer-in-Charge. The 'L' frame to be made out of single sheets in continuous length without any joints and fixed to sign using cross headed M4 screws the top member of frame shall be fixed using cross headed M4 screws to allow opening the frame for servicing lights. Powder coating shall be done on all internal as well as external surfaces. Illumination: Providing and fixing the LED strips for proper illumination Lighting suitable for sign box (make osram, lucoled or equivalent) – lifespan of 50,000 +hrs 6500K with optimal homogeneous backlighting & light throw of minimum4”) with electronic controllers, having even spread and overlap to avoid banding and dark spots and adhering to the LUX levels of 300 Lux. Cost to include all internal connections and wiring terminating and connecting with the incoming cable.connectors, wire harnesses, groumets and snaps and clips for fixing the LED lights. Above description generally holds good for the following signage unless otherwise specified except due modifications with special mention, the area will be calculated on the Size of the Graphic Face. Accessories: Providing and fixing all accessories such as nut-inserts, screws, rivets, bolts, washers, nuts, etc. complete as per drawing.Sign fixing: Each sign shall be suspended/projected/post mounted as per the site condition and elaborated in the sign schedule. A consolidated detail is provided in the relevant item and all the fixings.

Interior Illuminated sign 1 side Illuminated & back printed non-illuminated. Suspended, Projected, Post mounted. Drg. No.1.1.3 a, b. Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per relevant drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.Sign Box: The sign box 75 mm deep shall be fabricated out of 1.6 mm thick CRCA MS sheet and reinforced with spot welded inverted hat section for entire length at top and bottom and connected with couple of ties at a max spacing of 750 mm. Parts will be laser cut blanks bent and assembled with spot and CO2 welding. Joints/welds shall be minimized on account of continuous channel bent at corners facilitating maximum dimensional accuracy and repeatability. Sign box shall be provided with a ventilation fixture with Mesh from inside for ventilation confirming to IP54. Complete sign box including channel supports are to be powder coated to match GreyG1. Sign box flange receiving the sign face shall be provided with slots to receive the screws to fix the sign frame. Sign panel - Face 1 Illuminated: Providing and fixing sign panel on 1 side of sign box made out of 1.6 mm thick CRCA MS sheet frame fabricated to required size and shape, the frame shall be welded on 2 bottom corners making a 'L' and top part of frame fixed at site after inserting the sign face, complete frame shall be powder coated on all faces to match GreyG2. Sign face shall be made in 8 mm thick Opal white acrylic (as specified) having graphics pasted in Plotter cut Block out vinyl pasted over a translucent white vinyl and entire panel covered with a protective over laminate. The films to wrap around the edge of the acrylic to a distance of 25 mm on the back side. The Plotter cut block out vinyl shall match the specified colour (colour Pantone 2766 and Pantone 667C) and of specified make duly approved by the Engineer-in-Charge. The 'L' frame to be made out of single sheets in continuous length without any joints and fixed to sign using cross headed M4 screws. The top member of frame shall be fixed using cross headed M4 screws to allow opening the frame for servicing lights. Powder coating shall be done on all internal as well as external surfaces. Sign panel - Face 2 Blank Non-Illuminated Texture pattern: Providing and fixing sign panel on 1 side of sign box made out of 1.6 mm thick CRCA MS sheet frame fabricated to required size and shape, the frame shall be welded on 2 bottom corners making a 'L' and top part of frame fixed at site after inserting the sign face, complete frame shall be powder coated on all faces to match GreyG2. Sign face shall be made in 2 mm thick Aluminium sheet (as specified) having graphics pasted in Plotter cut Block out vinyl pasted over a translucent white vinyl and entire panel covered with a protective over laminate. The films to wrap around the edge of the acrylic to a distance of 25 mm on the back side. The Plotter cut block out vinyl shall match the specified colour (colour Pantone 2766 and Pantone 667C) and of specified make duly approved by the Engineer-in-Charge. The 'L' frame to be made out of single sheets in continuous length without any joints and fixed to sign using cross headed M4 screws. The top member of frame shall be fixed using cross headed M4 screws to allow opening the frame for servicing lights. Powder coating shall be done on all internal as well as external surfaces. Illumination:Providing and fixing the LED strips for proper illumination Lighting suitable for sign box (make osram, lucoled or equivalent) – lifespan of 50,000 +hrs 6500K with optimal homogeneous backlighting & light throw of minimum4”) with electronic controllers, having even spread and overlap to avoid banding and dark spots and adhering to the LUX levels of 300 Lux. Cost to include all internal connections and wiring terminating and connecting with the incoming cable. Cost to include all internal connections and external wiring for connecting to a nearest point left by the other contractor, end connectors, wire harnesses, groumets and snaps and clips for fixing the LED lights. Above description generally holds good for the following signage unless otherwise specified except due modifications with special mention the area will be calculated on the Size of the Graphic Face, only one face will be considered for measurement. Accessories: Providing and fixing all accessories such as nut-inserts, screws, rivets, bolts, washers, nuts, etc. complete as per drawing. Sign fixing: Each sign shall be suspended/projected/post mounted as per the site condition and elaborated in the sign schedule. A consolidated detail is provided in the next item and all the fixings.

Exterior Direction sign Non-Illuminated double sided. Suspended, Projected, Post mounted: Drg. No. 1.2.2a, b. Providing and fixing Non-illuminated signs in exterior areas including all operations from fabrication to installation all complete as per relevant drawings, technical specifications, signage schedule etc complete all as specified as under. Sign mounting frame: The sign mounting frame made up of 40x40x5 mm MS Equal angles as a frame back to back provided with welded angle cleats plates in 40x40x5 mm MS Equal angles along the perimeter of frame with slots to receive the rivets to fix the sign frame as per drawing. Complete mounting frame including channel supports are to be Powder Coated to match GreyG2 of approved make and duly approved by Engineer-in-Charge. Sign panel - Both faces: Providing and fixing sign face panels on either side of mounting frame made out of 4 mm thick Aluminium composite sheet white colour (as specified) folded and riveted over a frame fabricated in 25x25x2 mm MS square Hollow section to required size and shape, with welded Gusset plates in 2 mm thick MS Sheet 100 mm long at 300 mm c/c along the perimeter of frame the frame matching the gussets on mounting frame, complete frame shall be Powder coated on all faces to match GreyG2 before receiving the folded Aluminium composite panel All corners of sign face shall be finished and filled neat with white/clear silicon sealant. Graphics pasted in Plotter cut Block out vinyl pasted over a translucent white vinyl and entire panel covered with a protective over laminate. The Plotter cut block out vinyl to match the specified colour (colour Pantone 2766 and Pantone 667C) and of specified make duly approved by the Engineer-in-Charge. The sign panel shall be fixed to sign mounting frame using Blind rivets. All Powder coating shall be done on all internal as well as external surfaces. Fabrication of Hollow section shall ensure no openings/cavities for access of moisture to the inside of hollow section. Above description generally holds good for the following signage unless otherwise specified except due modifications with special mention the area will be calculated on the Size of the Graphic Face, only one face will be considered for measurement. Accessories: Providing and fixing all accessories such as nut-inserts, screws, rivets, bolts, washers, nuts, etc. complete as per drawing. Sign fixing: Each sign shall be suspended/projected/post mounted as per the site condition and elaborated in the sign schedule. A consolidated detail is provided in the next item and all the fixings. Sign Post: Post - Providing and fixing single sign post of 80 mm dia NB MS hollow sections fabricated along with end closed with 6 mm thick MS plate, providing with 25 x 25 x 3 mm MS equal angles as anchor bars welded at bottom for embedding in concrete. Entire post structure along with mounting frame to be welded and finished in PU paint to match GreyG3 colour. The item includes cutting and opening the floor finish at location on the footpath, excavation, fixing sign in PCC 1:2:4 as per drawing and finishing and making good the location to match the original finish after fixing and installation of sign. Providing and fixing stone pedestal made out of sadarhalli stone duly approved by engineer-in-charge using cement sand mortar as per drawing. Cost to include all fixtures nuts, bolts, screws, washers, anchor fasteners etc required for fixing the various parts of the sign.

Exterior Vicinity sign Non-Illuminated double sided: Post mounted: Drg. No.1.4a, 1.4.1. Providing and fixing Non-illuminated signs in exterior Vicinity areas of stations in a radius of 500 m with station at center at important junction on major roads. including all operations from fabrication to installation all complete as per relevant drawings, technical specifications, signage schedule etc complete all as specified as under. Sign mounting frame: The sign mounting frame made up of 40x40x5 mm MS Equal angles to form a frame provided with welded angle cleats plates in 40x40x5 mm MS Equal angles along the perimeter of frame with slots to receive the rivets to fix the sign frame as per drawing. Complete mounting frame including channel supports are to be Powder Coated to match GreyG3of specified make and duly approved by Engineer-in-Charge. The angles shall be cut to accommodate the post profile and welded to post to make a rigid connection. The frame shall be provided with MS angle spacers at corners to control the dimension. Sign Post: Post - Providing and fixing single sign post of 80 mm dia NB MS hollow sections fabricated along with end closed with 6 mm thick MS plate, providing with 25x25x3 mm MS equal angles as anchor bars welded at bottom for embedding in concrete. Entire post structure along with mounting frame to be welded and finished in PU paint to match GreyG3 colour. The item includes cutting and opening the floor finish at location on the footpath, excavation, fixing sign in PCC 1:2:4 as per drawing and finishing and making good the location to match the original finish after fixing and installation of sign. Providing and fixing stone pedestal made out of sadarhalli stone duly approved by engineer-in-charge using cement sand mortar as per drawing. Cost to include all fixtures nuts, bolts, screws, washers, anchor fasteners etc required for fixing the various parts of the sign.Providing and fixing sign face panels on either side of mounting frame made out of 4 mm thick Aluminium composite sheet white colour (as specified) folded and riveted over a frame fabricated in 25x25x3 mm MS Square Hollow section to required size and shape, with welded Gusset plates in 2 mm thick MS Sheet 100 mm long at 300 mm c/c along the perimeter of frame matching the gussets on mounting frame, complete frame shall be Powder coated on all faces to match GreyG2 before receiving the folded Aluminium composite panel All corners of sign face shall be finished and filled neat with white/clear silicon sealant. Graphics pasted in Plotter cut Block out vinyl pasted on face including sides over a translucent white vinyl and entire panel covered with a protective over laminate. The Plotter cut block out vinyl to match the specified colour (colour Pantone 2766 and Pantone 667C) and BMRCL Logo shall be pasted on panel in Plotter cut Opaque vinyl to match specified colour (Pantone 2425C and Pantone 361C) of specified make duly approved by the Engineer-in-Charge. The sign panel shall be fixed to sign mounting frame using Blind rivets. Fabrication of Hollow section shall ensure no openings/cavities for access of moisture to the inside of hollow section. Above description generally holds good for the following signage unless otherwise specified except due modifications with special mention, the area will be calculated on the Size of the Graphic Face, only one face will be considered for measurement. Accessories: Providing and fixing all accessories such as nut-inserts, screws, rivets, bolts, washers, nuts, etc. complete as per drawing. Sign fixing: Each sign shall be suspended/projected/post mounted as per the site condition and elaborated in the sign schedule. A consolidated detail is provided in the next item and all the fixings.

Exterior Totem sign 2-sided. Post mounted. Drg No. 2.1 e, Providing and fixing illuminated totem in exterior areas of stations with the BMRCL symbol close to the entrance visible form approach road including all operations from fabrication to installation all complete as per relevant drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge. Sign Structure: Providing and fixing in position internal structure for sign made in 50x50x4 MS Box Section with base plate 310x560x16mm and 10mm thick MS gusset plates and provided with 25x25x3 - 4 Nos MS equal angle welded with MS Box Section as per the drawing and dimensions. Entire structure shall be made as one unit and finished in Powder Coat to match Colour Silver Metallic after all welding and grinding of burr, making holes/slots receiving sign panels, fitting the tube lights and electronic ballasts, including provision of unpainted areas for welding the structure on post. Sign face shall be made in 3mm thick 040 white acrylic (as specified) having graphics pasted in Plotter cut Block out vinyl pasted over a translucent white vinyl and entire panel covered with a protective over laminate The structure shall have panels covering from top and bottom made in 4mm thick Aluminum Composite Grey in colour with the bottom panel allowing for ventilation of the sign as approved by the Engineer-in-charge. The Sign structure shall be covered from bottom using Aluminum composite panels as per drawing with provision for opening for accessibility and maintenance of the lights. Providing and fixing in position internal structure for sign made in 50x50x4 MS Box Section with base plate 310x560x16mm and 10mm thick MS gusset plates and provided with 25x25x3 - 4 Nos MS equal angle welded with MS Box Section as per the drawing and dimensions. Entire structure shall be made as one unit and finished in Powder Coat to match Colour Silver Metallic after all welding and grinding of burr, making holes/slots receiving sign panels, fitting the tube lights and electronic ballasts, including provision of unpainted areas for welding the structure on post. Sign face shall be made in 3mm thick 040 white acrylic (as specified) having graphics pasted in Plotter cut Block out vinyl pasted over a translucent white vinyl and entire panel covered with a protective over laminate The structure shall have panels covering from top and bottom made in 4mm thick Aluminum Composite Grey in colour with the bottom panel allowing for ventilation of the sign as approved by the Engineer-in-charge. The Sign structure shall be covered from bottom using Aluminum composite panels as per drawing with provision for opening for accessibility and maintenance of the lights. Accessories: Providing and fixing all accessories such as nut-inserts, screws, rivets, bolts, washers, nuts, etc. complete as per drawing. Foundation and Pedestal: Providing and laying foundation for the Totem sign in PCC (concrete M25) including its compaction and all activities like Excavation, PCC base layer, casting of holding down HTS anchor J bolts of 16mm dia using a sized template in MS 8mm thick for locating and accurate spacing of bolts as per drawing. Providing and fixing in position Sadarhalli stone pedestal in hand dressed rough finish surface in required size and shape as per drawing in 2 parts. Making cavity in stone for accommodating electrical box installing the two halves joined together by filling Plain cement concrete (M25) keeping a clear groove of 25mm wide recessed and finished as per drawing. 2mm thick SS clamps bolted and set into 3mm thick groove made 150mm from top and 200mm from bottom of the pedestal to keep it intact and flushed to face. The item cost includes cutting and opening the floor finish at location, and making good the location to the match the original finish after fixing and installation of sign. Sign panels: Providing and fixing sign face panels on 2 sides of sign structure made out of frame fabricated in 50x50x3 Aluminium Square Hollow box section to required size and shape shall be anodized on all faces to match Black Color before receiving 040 white acrylic and Aluminium composite panel. All corners of sign face shall be finished and filled neat with white/clear silicon sealant. The BMRCL symbol shall be router cut using original artwork in Acrylic Sheet shall be inserted in the panel projecting the acrylic face on the outside and the sides are maintained for light dispersion. The BMRCL Logo (950mm x 950mm x 75mm) shall be of specified make duly approved by the Engineer-in-Charge. The sign panel shall be inserted to sign mounting frame using Aluminium Composite Panel to Aluminium Profile. Illumination: Providing and fixing the LED strips for proper illumination Lighting suitable for sign box (make osram, lucoled or equivalent) – lifespan of 50,000 +hrs 6500K with optimal homogeneous backlighting & light throw of minimum4”) with electronic controllers, having even spread and overlap to avoid banding and dark spots and adhering to the LUX levels of 300 Lux. Cost to include all internal connections and wiring terminating and connecting with the incoming cable.

Interior Non-Illuminated Sign Single sided, Face mounted: Drg. No.2.2.1 a, b, Providing and fixing Non-illuminated signs including all operations from fabrication to installation all complete as per relevant drawings, technical specifications, signage schedule etc complete all as specified as under.Sign Mounting frame: The sign mounting frame made up of 25x25x3mm MS equal angles to form a frame and provided with same material ties 300mm c/c of length welded to top and bottom member, provided with holes for fixing to the back surface. All fabrication shall be done using CNC machines. Complete mounting frame including channel supports are to be powder coated to match GreyG1 duly approved by Engineer-in-Charge. Sign frame flange receiving the sign face shall be provided with slots to receive the Screws to fix the sign frame. Sign panel - Single face.: Providing and fixing sign panel on 1 side of sign box made out of 1.6mm thick CRCA MS sheet frame fabricated to required size and shape, the frame shall be welded on 2 bottom corners making a 'L' and top part of frame fixed at site after inserting the sign face, complete frame shall be powder coated on all faces to match GreyG2. Sign face shall be made in 2 mm thick aluminium sheet (as specified) having graphics pasted in Plotter cut Block out vinyl pasted over a translucent white vinyl and entire panel covered with a protective over laminate. The films to wrap around the edge of the acrylic to a distance of 25mm on the back side. The Plotter cut block out vinyl shall match the specified colour (colour Pantone 2766 and Pantone 667C) and of specified make duly approved by the Engineer-in-Charge. The 'L' frame to be made out of single sheets in continuous length without any joints and fixed to sign using cross headed M4 screws. The top member of frame shall be fixed using cross headed M4 screws to allow opening the frame for servicing lights. Powder coating shall be done on all internal as well as external surfaces. Above description generally holds good for the following signage unless otherwise specified except due modifications with special mention, the area will be calculated on the Size of the Graphic Face, only one face will be considered for measurement . Accessories: Providing and fixing all accessories such as nut-inserts, screws, rivets, bolts, washers, nuts, etc. complete as per drawing. Sign mounting frame: Sign mounting frame shall be fixed to the indicated surface (Wall, stone cladding) including all members required for mounting using 8mm dia anchor fasteners of specified make duly approved by the Engineer-in-Charge.

Interior Non-Illuminated sign double sided, Suspended, Projected, Post mounted: Drg. No. 2.2.2a, b. Providing and fixing Non-illuminated signs including all operations from fabrication to installation all complete as per relevant drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.Sign Box: The sign box 110mm deep shall be fabricated out of 1.6 mm thick CRCA MS sheet and reinforced with spot welded inverted hat section for entire length at top and bottom and connected with couple of ties at a max spacing of 750mm. Parts will be laser cut blanks bent and assembled with spot and CO2 welding. Joints/welds shall be minimized on account of continuous channel bent at corners facilitating maximum dimensional accuracy and repeatability. Sign box shall be provided with a ventilation fixture with Mesh from inside for ventilation confirming to IP54. Complete sign box including channel supports are to be powder coated to match GreyG1. Sign box flange receiving the sign face shall be provided with slots to receive the screws to fix the sign frame. Sign panel - Both faces: Providing and fixing sign panel on 1 side of sign box made out of 1.6mm thick CRCA MS sheet frame fabricated to required size and shape, the frame shall be welded on 2 bottom corners making a 'L' and top part of frame fixed at site after inserting the sign face, complete frame shall be powder coated on all faces to match GreyG2. Sign face shall be made in 8mm thick Opal white acrylic (as specified) having graphics pasted in Plotter cut Block out vinyl pasted over a translucent white vinyl and entire panel covered with a protective over laminate. The films to wrap around the edge of the acrylic to a distance of 25mm on the back side. The Plotter cut block out vinyl shall match the specified colour (colour Pantone 2766 and Pantone 667C) and of specified make duly approved by the Engineer-in-Charge. The 'L' frame to be made out of single sheets in continuous length without any joints and fixed to sign using cross headed M4 screws the top member of frame shall be fixed using cross headed M4 screws to allow opening the frame for servicing lights. Powder coating shall be done on all internal as well as external surfaces. Above description generally holds good for the following signage unless otherwise specified except due modifications with special mention, the area will be calculated on the Size of the Graphic Face, only one face will be considered for measurement . Accessories: Providing and fixing all accessories such as nut-inserts, screws, rivets, bolts, washers, nuts, etc. complete as per drawing. Sign fixing: Each sign shall be suspended/projected/post mounted as per the site condition and elaborated in the sign schedule. A consolidated detail is provided in the next item and all the fixings.