REPAIR MAINT OF CENTRIFUGAL SUBMERSIBLE PUMPS AND CONNECTED WORKS OTHER THEN FILTRATION PLANT AND RAW WATER BEECHWAL AND REPAIR REPLACEMENT OF LT PANEL, APFC PANEL WITH ACCESSORIES AND CONNCTED WORKS AT MIL STATION BIKANER

Amount

Taking out submersible pump and motor and lowering of capacity 2000 to 6000 GPH at 130 mtr head from the tube well lowered at the depth of 90 to 110 mtr from the ground level including taking out GI flanged column pipes 80 mm bore of 03 metre length each (column pipe are provided with flanged joints at every 03 metre length) and two Nos submersible cable 3 core of any size incl disconnecting electrically and delivery out let pipe and lowering there same in borewell after repairing and testing including refixing column pipes and submersible cables complete all as specified and directed. Note:- Repair work and spare parts of pumps and motor shall be measured and paid for separately under relevant items here-in-after.

Opening, reassembling and testing of submersible motor after rewinding & replacement of worn out spare parts incl rewinding of submersible motor 20 HP of 03 Phase, 415 volts with PVC insulated solid copper conductor (wire) superior quality of approved make , size & number of wire as per existing complete and also replacement of worn out cable connections, testing and commissioning of motor after rewinding complete all as specified. Make of Motor : CALAMA/SABAR/KSB/BED FORD GARVIN/KIRLOSKAR. Note:- (i) The spare parts required to be replaced shall be measured and paid for separately as "Supply only" under the relevant items here-in-after. (ii) Unit rate (quoted by the tenders) shall be deemed to include for all minor spares/extras. The decision of accepting officer regarding minor spares/extras shall be final, conclusive and binding.

Supply only the following spare parts for submersible motor capacity 20 HP, 3 phase, 415 volts against item Ser No 2 above. (a) GM Bush

(b) Rotor sleeve

(c) Water seal

(d) Thrust bearing Make- NBC/SKF

(e) Housing upper

(f) Housing lower

(g) Cable seal

(h) Thrust plate

(j) Coupling S/S

(k) Key for coupling

(l) LNK bolt S/S

(m) Revolving disc

(n) Seal bush

(p) Sand guard

(q) Rotor

(r) Stator

Opening, reassembling and testing of submersible pump of capacity 2000 to 6000 GPH including replacement of the worn out spare parts as mentioned under respective item No.20 to 26 here in after. Make of pump: CALAMA/SABAR/KSB/BED FORD GARVIN/KIRLOSKAR.

Supply only the following spare parts for submersible pump cap 2000 to 6000 GPH (a) Stage bowl

(b) Impeller GM.

(c) Pump shaft S/S (single stage)

(d) Hook bolt (Upper & lower)

(e) GM neck ring

(f) Key for pump shaft (Each stage)

(g) Distance sleeve

Supply and fixing to the extant required replacement under item No 1 here in before 80 mm bore GI pipe (length of three meter for each job) heavy grade with flange not less than 12mm thick duly drilled holes on each end, screwed and welded with necessary packing/jointing nut bolts & washers with four MS flat of size 12 x 6mm support on each flange with suitable cut/opening for cable complete all as specified and as directed by Engineer-in-Charge. Make : Jindal/Prakash Surya

Taking down of defective induction motor of the following capacity and make from the foundation, disconnecting the electric connecting coupling pulley, and transporting to work shop cutting down and removing existing burnt out copper windings, cleaning of slots and rewinding with solid copper conductor ( winding wire) complete including varnishing, drying, ovening, overhauling, greasing and fixing in the same position, making necessary electric connection and testing of induction motor complete all as specified and as directed by Engineer-in-Charge. (a) 75 HP capacity, 03 phase 415 volt 50 HZ

(b) 60 HP capacity,03 phase, 415volt 50 Hz

(c) 50 HP capacity,03 phase, 415volt 50 Hz

(d) 40 HP capacity, 03 phase, 415 volt 50 HZ

(e) 30 HP capacity, 03 phase, 415 volt 50 HZ

(f) 25 HP capacity, 03 phase, 415 volt 50 HZ

(g) 20 HP capacity, 03 phase, 415 volt 50 HZ

(h) 15 HP capacity, 03 phase, 415 volts 50 HZ

(j) 10 HP capacity, 03 phase, 415 volts 50 HZ

(k) 7.5 HP capacity, 03 phase, 415 volts 50 HZ

(l) 5 HP capacity, 03 phase, 415 volts 50 HZ

(m) 3 HP capacity, 03 phase, 415 volts 50 HZ

(n) 2 HP capacity, 03 phase, 230 volts 50 HZ

(o) 1.5 HP capacity, 01 phase, 230 volts 50 HZ

(p) 1 HP capacity, 01 phase, 230 volts 50 HZ

(q) 0.5 HP capacity, 01 phase, 230 volts 50 HZ

Taking down from foundation base frame by disconnecting suction/delivery lines and coupling, opening including dismantling of centrifugal pump set of capacity 75 HP model DSM 100-36, and replacement of worn out spare parts as mentioned under respective item No.45 to 52 here in after and re-assembling, installation in same location including testing aa as directed. Make : Kirloskar

Supply only the following spare parts for centrifugal pump of 75 HP capacity model DSM 100-36 required to be replaced under item No 44 above, Make:- Kirloskar (a) Inter stage ring

(b) Gland Cap CI with nut bolt complete

(c) Wear ring CI

(d) Shaft Sleeve Bronze

(e) Shaft Sleeve Nut (Bronze)

(f) SS pump shaft as per existing

(g) GM impallar comlete with impolar key

(h) Gasket set manifold

Taking down from foundation base frame by disconnecting suction/delivery lines and coupling, opening including dismantling of centrifugal pump set of capacity 60 HP model DSM 100-36 and replacement of worn out spare parts as mentioned under respective item No. 54 to 61 here in after and re-assembling, installation in same location including testing as directed . Make: Kirloskar

Supply only the following spare parts for centrifugal pump of 60 HP capacity model DSM 100-36 Make:- Kirloskar (a) Inter stage ring

(b Gland cap CI with nut bolt

(c) Wear ring CI

(d) Shaft Sleeve Bronze

(e) Shaft Sleeve Nut (Bronze)

(f) SS pump shaft as per existing

(g) GM impallar comlete with impolar key

(h) Gasket set manifold

Taking down from foundation base frame by disconnecting suction/delivery lines and coupling, opening including dismantling of centrifugal pump set of capacity 50 HP model DSM 100-36 and replacement of worn out spare parts as mentioned under respective item No.63 to 67 here in after and re-assembling, installation in same location including testing aa as directed . Make : Kirloskar

Supply only the following spare parts for centrifugal pump of 50 HP capacity model DSM 100-36 Make:- Kirloskar (a) Inter stage ring

(b) Gland cap CI with nut bolt

(c) Wear ring CI

(d) Shaft Sleeve Bronze

(e) Shaft Sleeve Nut (Bronze)

Taking down from foundation frame by disconnecting suction/delivery lines and coupling opening including dismantling of centrifugal pump set of capacity 40 HP Model No: UP 100-38 and replacement of worn out spare parts as mentioned under respective item No, 69 to 76 here in after and re-assembling, installation in same location including testing aa as directed . Make : Kirloskar

Supply only the following spare parts for centrifugal pump of 40 HP capacity model UP 100-38 Make:- Kirloskar (a) Inter stage ring

(b) Gland Cap CI with nut bolt

(c) Wear ring

(d) Shaft sleeve Bronze

(e) Shaft sleeve nut bronze

(f) SS pump shaft as per existing

(g) GM impallar comlete with impolar key

(h) Gasket set manifold

Taking down from foundation frame by disconnecting suction/delivery lines and coupling opening including dismantling of centrifugal pump set of capacity 30 HP Model No: UP 80-38 and replacement of worn out spare parts as mentioned under respective item No. 78 to 85 here in after and re-assembling, installation in same location including testing aa as directed. Make : Kirloskar

Supply only the following spare parts for centrifugal pump of 30 HP capacity model UP 80-38 Make:- Kirloskar (a) Inter stage ring

(b) Gland Cap CI with nut bolt

(c) Wear ring

(d) Shaft sleeve bronze

(e) Shaft sleeve nut ( Bronze)

(f) SS pump shaft as per existing

(g) GM impallar comlete with impolar key

(h) Gasket set manifold

Taking down from foundation frame by disconnecting suction/delivery lines and coupling opening including dismantling of centrifugal pump set of capacity 25 HP Model No: UP 80-38 and replacement of worn out spare parts as mentioned under respective item No. 87 to 91 here in after and re-assembling, installation in same location including testing aa as directed. Make : Kirloskar

Supply only the following spare parts for centrifugal pump of 25 HP capacity model UP 80-38 Make:- Kirloskar (a) Inter stage ring

(b) Gland Cap CI with nut bolt

(c) Wear ring

(d) Shaft sleeve bronze

(e) Shaft sleeve nut ( Bronze)

Taking down from foundation frame by disconnecting suction/delivery lines and coupling opening & re-assembling of centrifugal pump set of capacity 20 HP Model No: UP 80-38 and replacement of worn out spare parts as mentioned under respective item No. 93 to 100 here in after and re-assembling, installation in same location including testing as directed. Make : Kirloskar

Supply only the following spare parts for centrifugal pump of 20 HP capacity model UP 80-38 Make:- Kirloskar (a) Inter stage ring

(b) Gland Cap CI with nut bolt

(c) Wear ring

(d) Shaft sleeve Bronze

(e) Shaft sleeve nut ( Bronze)

(f) SS pump shaft as per existing

(g) GM impallar comlete with impolar key

(h) Gasket set manifold

Taking down from foundation frame by disconnecting suction/delivery lines and coupling opening including dismantling of centrifugal pump set of capacity 15 HP Model No: DSM-2E/UP 80-30 and replacement of worn out spare parts as mentioned under respective item No. 102 to 109 here in after and re-assembling, installation in same location including testing aa as directed. Make : Kirloskar

Supply only the following spare parts for centrifugal pump of 15 HP capacity model DSM-2E/UP 80-30 Make:- Kirloskar (a) Inter stage ring

(b) Gland Cap CI with nut bolt

(c) Wear ring

(d) Shaft sleeve bronze

(e) Shaft sleeve nut ( Bronze)

(f) SS pump shaft as per existing

(g) GM impelar comlete with impolar key

(h) Gasket set manifold

Dismantling opening and reassembling after repair /replacement of U/S spare parts of mono block pumping set capacity 10 HP spare parts required shall be measured and paid for under respective item Sr No 111 to 112 of this schedule. Job includes disconnection from base foundation frame disconnecting electrically, reconnection, re-fixing in position transportation to work shop & back make of pump :- Kirlosker

Supply only the following spare parts for mono block pump of 10 HP capacity Make:- Kirloskar (a) Gland bush

(b) Gasket set manifold

Description all as per item No .110 but of cap 7.5 HP spare parts shall be measured and paid for under respective item Ser No 114 to 115.

Supply only the following spare parts for monoblock pump of cap 7.5 HP , Make : Crompton Greaves (a) Gland Bush

(b) Gasket set manifold

All as per item No .101 but capacity 5 HP spare parts required shall be measured and paid for under respective item Sr No 117 & 118

Supply only the following spare parts for mono block pump of 5 HP capacity Make:- Kirloskar (a) Gland bush

(b) Gasket set manifold

S&F in replacement following items suitable for 75 HP motor pumping set (a) Flexible tyre type coupling

(b) Ball bearing for motor(SKF/NBC)

(c) Ball bearing for pump ( SKF/NBC)

S&F in replacement following items suitable for 60 HP motor pumping set (a) Flexible tyre type coupling

(b) Ball bearing for motor(SKF/NBC)

(c) Ball bearing for pump ( SKF/NBC)

S&F in replacement following items suitable for 50 HP motor pumping set (a) Flexible tyre type coupling

(b) Ball bearing for motor(SKF/NBC)

(c) Ball bearing for pump ( SKF/NBC)

S&F in replacement following items suitable for 40HP motor pumping set (a) Flexible tyre type coupling

(b) Ball bearing for motor(SKF/NBC)

(c) Ball bearing for pump ( SKF/NBC)

S&F in replacement following items suitable for 30HP motor pumping set (a) Flexible tyre type coupling

(b) Ball bearing for motor(SKF/NBC)

(c) Ball bearing for pump ( SKF/NBC)

S&F in replacement following items suitable for 25HP motor pumping set (a) Flexible tyre type coupling

(b) Ball bearing for motor(SKF/NBC)

(c) Ball bearing for pump ( SKF/NBC)

S&F in replacement following items suitable for 20 HP pumping set (a) Flexible tyre type coupling

(b) Ball bearing for motor(SKF/NBC)

(c) Ball bearing for pump ( SKF/NBC)

S&F in replacement following items suitable for 15 HP motor pumping set (a) Flexible tyre type coupling

(b) Ball bearing for motor(SKF/NBC)

(c) Ball bearing for pump ( SKF/NBC)

S&F in replacement following items suitable for following cap of motor(a) Ball bearing for 10 HP (SKF/NBC)

(b) Ball bearing for 7.5 HP (SKF/NBC)

(c) Ball bearing for 5 HP motor(SKF/NBC)

(d) Ball bearing for 3 HP motor(SKF/NBC)

(e) Ball bearing for 2 HP motor(SKF/NBC)

(f) Ball bearing for 1.5 HP motor(SKF/NBC)

(g) Ball bearing for 1 HP motor(SKF/NBC)

(h) Ball bearing for 0.5 HP motor(SKF/NBC)

Replacement of U/S leather washers heavy duty with new leather washer heavy duty (ISI marked) suitable for foot valve of following size.(a) 150mm bore

(b) 100mm bore

(c) 80mm bore

Replacement of U/S foot valve with new foot valve of following size flanged/screwed type Make:- Kirlosker/ISI marked (a) 150 mm bore

(b) 100mm bore

( c) 80 mm bore

S&F in replacement PVC insulated sheathed 3 core submersible flat cable for submersible pumps copper conductor cable (stranded) 1100 volt grade of size 10 Sq mm Make:- Plaza/finolex

supply and fix in replacement MCCB 63 Amp capacity triple pole breaking capacity 16 KA,FP, single frame, fixed thermal magnetic trip at 415 volts in existing panels of booster pump houses including making connections by using suitable size copper lugs/thimbles and crimping tool complete all as specified and directed by Engr in charge Make: - L&T/Havells/C&S

.-do- but 125 Amp Capacity 25 KA

.-do- but 400 Amp Capacity 36 KA

.-do- but 250 Amp Capacity 36 KA

Taking down unsv & supply and fix MCCB 4 Pole, 415 V, Adjustable type, 160 Amps with breaking capacity 36 KA

S&F electronic type single phasing preventer in existing panel boards (max 600V min 380V) three phase 415volts variation voltage 4% tripping time 2-5 sec max type VSP-1 complete all as directed by Engr in charge. Make:- L&T/Minilac/Siemens.

Supply and fix in replacement star delta timer range 0-30 second Make : C&S/L&T /Schiender

Dismantling of NRV of size 150/200mm carefully after disconnecting from delevery line of pumping set unscrewing the both side taking out seat with level and labour and material from replacement of leather washer cleaning inside seat space reassembling , reinstalling back complete as directed by Engineer-in-Charge.

Supply and fixing in replacement of NRV CI flanged ends ISI marked ( IS-5312) size 200mm bore with rubber or fibre board gasket including necessary nuts, bolts and washer complete all as specified and directed . Make : KIRLOSKAR/BIR/Upadhaya

All as per item No 167 above but of 150mm bore

supply and fixing contactor of following cap of motor including disconnecting and taking down old existing unserviceable contactor (a) Contactor rating suitable for 40 Amp, 3 Pole with (01 No + 01 NC) for 20 HP motor

(b) Contactor rating suitable for 60 Amp,3 Pole with (01 No + 01 NC) for 30 HP motor

(c) Contactor rating suitable for 80 Amp,3 Pole with (01 No + 01 NC) for 40 HP motor

(d) Contactor rating suitable for 115 Amp,3 Pole with (01 No + 01 NC) for 50 HP motor

(e) Contactor rating suitable for 115 Amp,3 Pole with (01 No + 01 NC) for 60 HP motor

(f) Contactor rating suitable for 150 Amp, 3 Pole with (01 No + 01 NC) for 75 HP motor

Opening the gland cap from both side of centrifugal pump and taking out the rusted gland dori and refilling the new gland dori with grease both side of pump and refixing the gland cap in same position.

Taking up or down existing old/rusted/worn out cracked/broken 25mm bore GI pipe water tubing & connections.

Supply and fixing to walls, laid on roofs laid on floors, GI pipe of size 25mm bore ISI marked medium grade complete with fittings all as specified and directed by Engr in Charege.

M&L for opening the gland cap from both side of sluice vale and taking out the rusted gland dori and refilling the new gland dori with grease both side of sluice valve and refixing the gland cap in same position.

Taking out of UNSV analogue Amp meter and supply and fix new digital ebrit panel mounted AC ammeter (0-300A) of size 96 X 96 sqmm flush mounted case three phase, class 0.5 item code PAMEBRITA 32. Make:-AE/HPL

Taking down UNSV phase indicator lamp supply and fix new phase indicator lamp (red, yellow & blue)

Taking out of UNSV analogue volt meter and supply and fix new digital ebrit panel mounted AC volt meter (0-500A) of size 96 X 96 sqmm flush mounted case three phase, class 0.5 item code PAMEBRITA 32. Make:-AE/HPL

Supply and fixing in replacement motor protection relay range 13-20 Amp

Supply and fixing in replacement motor protection relay range 22-30 Amp

Supply and fixing in replacement motor protection relay range 25-39 Amp

Supply and fixing in replacement motor protection relay range 38-60 Amp

S&F 20 mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, including dismantling & taking out old unserviceable gate valve of 20mm bore, complete, all as specified & directed. Make :- Leader/ Zoloto

S&F 25mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, including dismantling & taking out old unserviceable gate valve of 25 mm bore, complete, all as specified & directed. Make :- Leader/ Zoloto

M&L for repair to unserviceable sluice valve of size 80mm bore by dismantling and opening the gland cap and head of sluice valve and taking out the unserviceable lock nut, fitting the material on serviceable spindle, grinding the material cutting the threads by lathe machine and fabrication of new lock nut with cutting the threads inside the lock nut according to the spindle threads and refixing in the same position, testing the sluice valve, complete, all as specified and directed.

M&L for repair to unserviceable sluice valve of size 100mm bore by dismantling and opening the gland cap and head of sluice valve and taking out the unserviceable lock nut, fitting the material on serviceable spindle, grinding the material cutting the threads by lathe machine and fabrication of new lock nut with cutting the threads inside the lock nut according to the spindle threads and refixing in the same position, testing the sluice valve, complete, all as specified and directed.

M&L for repair to unserviceable sluice valve of size 150mm bore by dismantling and opening the gland cap and head of sluice valve and taking out the unserviceable lock nut, fitting the material on serviceable spindle, grinding the material cutting the threads by lathe machine and fabrication of new lock nut with cutting the threads inside the lock nut according to the spindle threads and refixing in the same position, testing the sluice valve, complete, all as specified and directed.

M&L for repair to unserviceable sluice valve of size 200mm bore by dismantling and opening the gland cap and head of sluice valve and taking out the unserviceable lock nut, fitting the material on serviceable spindle, grinding the material cutting the threads by lathe machine and fabrication of new lock nut with cutting the threads inside the lock nut according to the spindle threads and refixing in the same position, testing the sluice valve, complete, all as specified and directed.

Supply & fixing in replacement cast iron body sluice valve heavy duty class ‘PN-1.6’ of 80 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and MS nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable CI sluice valve of 80 mm bore, complete, all as specified & directed.

Supply & fixing in replacement cast iron body sluice valve heavy duty class ‘PN-1.6’ of 100 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and MS nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable CI sluice valve of 100 mm bore, complete, all as specified & directed.

Supply & fixing in replacement cast iron body sluice valve heavy duty class ‘PN-1.6’ of 150 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and MS nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable CI sluice valve of 150 mm bore, complete, all as specified & directed.

Supply & fixing in replacement cast iron body sluice valve heavy duty class ‘PN-1.6’ of 200 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and MS nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable CI sluice valve of 200 mm bore, complete, all as specified & directed. Note for item No. 192, 193, 194 to 195:- (i) Contractor shall be sumit teh original test certificate and purchase voucher of valves. (ii) Paymant shall be release after verification of purchase voucher/test certificate of valves.

Supply & laying suction/delivery GI pipe line of size 150mm bore ISI marked medium grade in short length both side flanged type with gasket joint nut bolts washers complete with fittings all as specified & directed by the Engineer-in-Charge. Make:- Jindal/Swastik/Tata

-do- but of size 100mm bore.

Supply and fix Submersible pump set 13 stage of cap 6.67LPS/M3/hr at 123 mtr head of motor capacity 20 HP complete all as directed by Engineer-in-Charge. Make:- Crompton Model No 6W20020

S&F in replacement of metallic antivibration pads with rubber cushion for 75/60/50/40/30/25/20 HP motor pumping set including drilling hole at necessary places on foundation base frame. MAKE: Dunlop

Dismantling and taking down pump set from base foundation frame by disconnecting electrically and from coupling side taking out at side and demolition the old fondation and making foundation with PCC(1:2:4) type By using 20mm graded stone aggregate including grouting of base hole fast 08 Nos and metalic anti vibration pads with rubber cusion including watering leveling at same size after making of foundation installing of P/S and fixing same suction and delivery all as directed by Engr - in- Charge , suitable for following cap (a) 75/60 HP

Taking down carefully existing unserviceable Copper/aluminum batten/surface conduit/concealed conduit point wiring (light, fan, bell/buzzer, socket or power) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, pendents, sockets, lamp holders, shades, fan regulators, light fittings, bells etc (including old MS sunken boxes) and removing the retrieved materials from dismantling including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and as directed by the Engr-in-Charge.

Taking down of unserviceable DBs/switch fuses/changeover in sheet steel enclosure complete with MCBs/Fuse/grips any capacity and removing from site disturbed surface of wall, floor etc. Taking after disconnecting all cable complete all as specified and as directed by the Engr-in-Charge.

M&L Point wiring with stranded copper conductor cable, 1100 volts grade (ISI marked) PVC insulated and unsheathed of size 1.5 Sq mm single core in and including PVC casing capping with all fittings such as tees, bends etc terminating in and including new sunken box covered with and including 3 mm thick bakelite laminated sheet top cover ‘Hylam’ for one fan or light or exhaust fan or bell/buzzer point controlled by one switch including provision of 1.5 Sqmm PVC insulated unsheathed copper conductor cable, single core as earth wire to common earth & connecting to earth dolly complete all as specified and directed by Engineer-in-Charge.

All as per item No 204 here-in-before but socket point on the same board with other switches complete as specifed as directed by Engineer - In - Charge

All as per item No 204 here-in-before but socket point on the independent board with other switches complete as specifed as directed by Engineer - In - Charge

All as per item No 204 here-in-before but cable of 2.5 Sq mm for 15 Amp switch socket outlet on independent board

S&F Switch piano flush type, Single pole 5 Amps, one way ISI marked, complete all as specified and as directed by Engineer-in-Charge

M&L Ceiling rose PVC/poly carbonate insulated body three terminal ISI marked, complete all as specified and as directed by Engineer-in-Charge.

S&F Socket outlet flush type, 2 in one 1 pin, 5 Amps, ISI marked, complete all as specified and as directed by Engineer-in-Charge.

S&F Switch piano flush type, Single pole 15 Amps, one way ISI marked, complete all as specified and as directed by Engineer-in-Charge

S&F Socket outlet flush type, 3 pin, 15 Amps, ISI marked, complete all as specified and as directed by Engineer-in-Charge.

S&F Lamp holder insulated body with back plate for conduit/casing capping fittings with 9 Watt LED bulb complete all as specified and as directed by Engineer-in-Charge.

S&F Fan regulator electronic type, 230 Volt, 150 Watt with 5 step of control including making holes in laminated bakelite sheet cover and connection complete all as specified and as directed by Engineer-in-Charge.

S&F Decorative ultra slim linear LED lightening fixture, energy efficent 18/20 Watt complete all as specified and directed by engineer-in-charge.Make Surya /Phillips/wipro/CG /Bajaj

Sheet metal enclosure for distribution boards, suitable for fixing MCBs 240 volts with 200 Amps rated bus bar, SPN, 8 ways double door , supplied and fixed in repair, including making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge.

Sheet metal enclosure for distribution boards, suitable for fixing MCBs 240 volts with 200 Amps rated bus bar, SPN, 4 ways double door , supplied and fixed in repair, including making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge.

MCB single pole, 240 volts of rating 6-32 Amps, breaking capacity of 10 KA complete all as specified and as directed by Engineer-in-Charge

MCB suitable for 6 to 32 Amps, 240 Volt AC supply single pole and neutral with over load and short circuit protection having rupturing capacity not less than 10 KA complete all as specified and as directed by Engineer-in-Charge.

Taking down old sub main wiring and providing new sub main wiring with 2 single core, multi-stranded PVC insulated cable unsheathed 1100 volts grade with copper conductor of size 2.5 sq mm drawn in and including PVC concealed including earth continuity conductor cable of size 1.5 sq mm PVC insulated unsheathed copper conductor cable connected to common earth and earth dolly complete all as specified and as directed by Engineer-in-Charge.

Supply and laying in replacement cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6.00 sq mm 2 core

Supplying, fixing, installation, commissioning & testing of self priming automatic pressure pumping set with numematic senser, pressure tank of suitable including all connecting accessories complete set 0.5 HP single phase 230 Volts AC Supply. Make : Kirloskar/CG/Bajaj.

Supplying, fixing, installation, commissioning & testing of self priming automatic pressure pumping set with numematic senser, pressure tank of suitable including all connecting accessories complete set 0.75 HP single phase 230 Volts AC Supply. Make : Kirloskar/CG/Bajaj.

Excavation in trenches in soft/loose soil not exceeding 1.5 meter wide and not exceeding 1.5 mtr in depth for route of cable and getting out complete all as specified and as directed by the Engr-in-charge.

Returning, filling in soft/loose soil including spreading, leveling watering and well ramming, in layers not exc 25 cm complete all as specified and as directed by the Engr-in-charge.

Removing of surplus soil to a distance not exc. 50 mtr and depositing where directed at a level not exc. 1.5 mtr above the starting point complete all as specified and directed by Engr-in-charge.

Protection to cable with one layer of bricks laid flat butting to each other in such a way that the length of the bricks is at right angle to the central axis of the cable using old size sub-class 'B' bricks complete all as specified and directed by Engr-in-charge.

Local tibba dry sand cushioning for protection of cable complete all as specified and as directed by Engineer-in-charge. Note Local approved tibba dry sand after removal of vegetations, grass and other deleterious substances shall be used for sand cushioning.

M & L GI tubing light grade for protection of cables with pole/ in ground of size 40mm dia complete all as specified and as directed by Engineer-in-Charge.

Supply and fix centrifugal Monoblock pump set (65 mm x 50 mm) of capacity 3HP (2.25 KW), 9m -25 mtr head, discharge range 32400L/hr single phase 240 volt 50Hz complete all as specified. Make : CG/Kirloskar Model No. CMR30-W

Supply and fixing LED street light fitting 70 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. . Make:- Havells/CG/Philips

M&L for cleaning of water supply installation in surrounding area (entire in fencing ) including trimming, grsass cutting etc two times in a contract period complete all as specified and as directed by Engineer-in-Charge.

Meterial and labour for construction of brick masonary valve pit chamber of size 150 X 150 X 150 cm (internal dimension) using sub class 'B' bricks complete including necesary earth work etc. type 'B' including PCC 1:5:10 type E-2 using 20 mm graded stone aggregate in foundation, coping on top in PCC type B-2 using 20 mm graded stone aggregate, inner plaster 10 mm thick in cement mortar 1:4, MS sheet cover 1.6 mm thick with locking arrangement duly painted with two coats of synthetic enemal paint over a coat of primer red oxide including angle iron 35 X 35 X 4 mm frame complete all as specified and as directed

Supply and fix MS sheet cover 1.6 mm thick with locking arrangement duly painted with two coats of synthetic enemal paint over a coat of primer red oxide including angle iron 35 X 35 X 4 mm frame for masonary valve pit chamber of size 150 X 150 X 150 cm (internal dimension)complete all as specified and as directed.

Supply and fix MS sheet cover 1.6 mm thick with locking arrangement duly painted with two coats of synthetic enemal paint over a coat of primer red oxide including angle iron 25 X 25 X 4 mm frame for masonary valve pit chamber of size 90cm X 90 cm (internal dimension) complete all as specified and as directed.

Taking down broken /rusted iron base frame and Supply and fixing new iron base frame for centrifugal pump set of capacity 40/30/20 HP as per existing size with two coats of black paint over a coat of red oxide zinc chromate primer complete all as specified.

Plain cement concrete (1:2:4) type C-2 using 20 mm graded stone aggregates as in foundation of poles above ground level including finishing to exposed concrete surfaces even and fair and provision of form work for rough finished surfaces complete all as specified and as directed by Engineer-in-Charge.

Repair / replacement of LT panel, APFC Panel with accessories and conncted works:- Supply and fixing in Bus Bar Chamber cubical type of size 80x50x40 cm (Box size), with bus bar chamber having 4 wire 415 Volts, factory made dust proof vermin proof for out door using made out of CRCA sheet 2 mm thick powder coated, machine pressed, both side opening in two halves with provision of rubber beadings and locking system, including aluminium bus bar of 400 Amp capacity, 4 strip mounted on DMC/Epoxy insulator, bus bar chamber shall be provided with inspection covers, each MCCB/ cubical switch shall have independent opening , panel shall be mounted on angle iron frame and legs made from angle of size 40x40x6mm , frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer, legs grouted in PCC (1:2:4) type B-1(using 20 mm graded stone aggregate) complete including the following accessory complete all as directed by Engineer-in-charge.(i) MCCB, 200 Amps, 4 pole, 415 Volts, rupturing capacity not less than 36 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and double break fast tripping mechanism complete withspreader link (incoming) -01 No. 1.All BOQ Items are considered for fault repair and maintanace of LT panel , APFC panel and connected infrastucture at Bikaner Mil station and different ASCON nodes located at 200 KMs away from Bikaner City. No extra cost for fault finding at ASCON nodes will be given to contractor. 2.Repair and maintanace intimated to the contractor or his rep at any time day or night, through complaint slip or telephonically must be rectified by the contractor within 8 Hrs.

All as per item No. 1 here-in-before but using aluminium bus bar of 300Amp capacity and for provision of following accessory (i) MCCB, 160 Amps, 4 pole, 415 Volts, rupturing capacity not less than 25 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and double break fast tripping mechanism complete withspreader link (incoming) -01 No.

Dis-connecting the ACB ( Air Circuit Breaker) panel capacity ranging from 600 to 2000 Amp of Make : CG/ABB /L&T /Simens /Schnider, Over hauling of complete bearker panel by taking out the trolley of the breaker, opening the total mechanism of breaker checking its contact, baffle plates and other minor parts, cleaning the complete accessories carefully. Minor repairs shall be rectified, Parts/accessories shall be cleaned, the tank, baffle plates, rotating contact, upper supports, lower supports, drive assembies and all other spare parts all as directed by Engineer-in-Charge. Reassembled Breaker after repair/ replacement of the faulty parts, testing and calibration of ACB realy settings complete.

Supply only spring charging motor 220 V AC/DC supply.

Shunt Release EA1 415V AC

Under-voltage Release 415V AC

Closing Preventer 415V AC

Supply only Jaw contact Assy. 630/1000A S1

Supply only Jaw contact Assy. 800/1000A C/H & 1250A S1

Supply only Jaw contact Assy. 1250/1600A C/H, 1600/2000A S1

Supply only Pole Assy. 630-1250 S1 D/O

Supply only Pole Assy. 1250/1600 C & 1600 S1 D/O

Taking out old underground LT Cable of size 10 sqmm to 120 Sqmm of 3.5 core from LT Panelstrenches/floors /road/wall/ pipe/pole/including taking out loop from trenches upto 1.5 mtrs depth, cutting the faulty end of cable and refixing the cable in original position by using flat aluminium sockets/ thimble/ and insulating the all nacked wires of any size including making connection with MCCB's/ Switches complete all as directed by Engineer-in-Charge. Note : Exacavation for taking out LT cable from will measured and paid separatly.

All as per item No. 250 here-in-before but 150 Sqmm to 630 Sqmm 3.5 core

Excavation in trenches not exceeding 1.5 mtr wide, and not exceeding 1.5 mtr in depth; for laying of cables, pipes in soft/loose soil etc and not exceeding 10 Sqm on plan and getting out including trimming of sides all as specified and directed by Engineer-in-Charge

Returning filling in, including spreading , levelling, watering and well ramming in layers each not exceeding 25cm in soft/loose soil complete all as specified.

Removing surplus spoil to distance not exceeding 50metre and depositing where directed at level not exceeding 1.5metre above the starting point complete all as specified.

Material and labour for protection to cable with one layer of new bricks laid flat butting to each other in such a way that the length of the brick is at right angle to the central axis of the cable using old size sub class ‘B’’ brick having compressing strength not less than 75 Kg/ Square cm complete all as specified and as directed.

Local tibba dry sand cushioning and cover (8 cm thick layer of sand before laying of cable and 15 cm thick layer of sand after laying of cable) for protection of cable, material and labour complete all as specified and as directed by Engineer-in-Charge.

Dis connecting the LT panel of any size and Cap and repair of complete panel by taking out the cable ,Bus -bar , Voltmtr , Amp mtr ,including wiring and other minor parts, cleaning the complete accessories carefully. Minor repairs shall be rectified Parts/accessories shall be cleaned properly and refixing the parts at its original locations, checking and repair of the internal panel wiring with suitable size of wire and remove the carbon deposited inside the contact, cleaning all other spare parts all as directed by the Engineer-in-charge and reassembled after repair/replacement of following parts.

Supply and fixing in replacement Cable indoor/outdoor end terminal jointing kit for LV/LT 1100 V cable heat shrinkable type joint kit complete with jointing material, 04 Nos coloured sleeves(Red, Blue, Yellow and black) each 45 cm long and accessories thimbles etc suitable for 25 sqmm to 50 sqmm 3.5 core XLPE armoured aluminium conductor cable including testing after jointing fixing in replcement complete all as specified and as directed by Engineer- in - charge.

Ditto All as per Srl Item No.258 Here in above but 70 Sqmm to 150 sqmm 3.5 core

Ditto All as per Srl Item No.258 Here in above but 185 Sqmm to 300 sqmm 3.5 core

Ditto All as per Srl Item No.258 Here in above but 400 Sqmm 3.5 core

Ditto All as per Srl Item No.258 Here in above but 500 Sqmm 3.5 core

Ditto All as per Srl Item No.258 Here in above but 630 Sqmm 3.5 core

Supply and fixing in replacement Cable jointing kit for LV/LT 1100 V cable for straight through , heat shrinkable type joint kit complete with jointing material and accessories suitable for 25 Sqmm to 50 Sqmm 3.5 core XLPE armoured aluminium conductor cable including testing after jointing, fixing in replacement complete all as specified as directed by Engineer-in-Charge.

Ditto All as per Srl item No 264 here in above but 70 Sqmm to 150 sqmm 3.5 Core

Ditto All as per Srl item No 264 here in above but 185 Sqmm to 300 sqmm 3.5 Core

Supply and fixing in replacement Cross linked poly-ethylene (XLPE) insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables ( heavy duty) with aluminium conductor, 1100 volts LT grade of cross-sectional area 10 Sqmm 02 core laid in trenches/through pipe in road crossings/ paths /drains /ducts /floors /along poles/walls/ceilings/ equipments etc supplied, fixed/ laid in repair including commissioning and testing complete all as specified and as directed by Engineer-in-Charge.(Note: :- (i) Necessary excavation and earth work, brick protection, sand cushioning and cover and GI pipe shall be measured and paid for separately.(ii) Road manually cutting/floor cutting/cutting holes etc in wall required for laying /fixing of cable etc shall be made good as per existing site condition. Nothing extra shall be admissible on this account and quoted rate for this item shall be deemed to include for the same) Make : Gloster/Havells/CCI/Polycab

Ditto All as per Srl item No 267 here in above but size of cable 25 Sqmm 4 core

Ditto All as per Srl item No 267 here in above but size of cable 35 Sqmm 3.5 core

Ditto All as per Srl item No 267 here in above but size of cable 50 Sqmm 3.5 core

Ditto All as per Srl item No 267 here in above but size of cable 95 Sqmm 3.5 core

Supply and fixing in replacement GI pipe light grade 40 mm bore (ISI marked) laid in trenches/ road crossings/ fixed to poles/ceiling / along walls/ path /drain/floors with and including all necessary clamps, nuts, bolts, washers etc and all fittings as required, complete all as specified and as directed by the Engineer-in-Charge. (Note :- Necessary excavation, earth work and same work shall be measured and paid for separately.)

Ditto All as per Srl item No 35 here in above but dia of pipe 50 mm

Boring of holes under road 100 mm dia, pavement, hard standing by trench less technology(manually) with out disturbing the top surface of roads for laying of cables/GI pipes complete all as specified and as directed by the Engineer-in-Charge.

Taking out old LT underground cable from trench depth upto 1.5 mtrs and laying after removing of defects any type/size laid in trenches including testing complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement shutters made out of 2.00 mm thick mild steel sheet, bent to shape, including taking out old damaged unservicable shutter complete with hinges, handle etc. complete all as directed by Engineer-in-Charge.

Supply and fixing in replacement mild steel medium weight Butt Hinges 100 mm long and fixed with steel screws complete all as specified.

Supply and fixing in replacement mild steel medium weight Butt Hinges 75 mm long and fixed with steel screws complete all as specified.

Supply and fixing in replacement mild steel pressed handles, size 75mm,complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement mild steel pressed handles, size 100 mm,complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement indicator lamp in diffrent colour code LED/Neon type complete (RYBW) including wiring with copper conductor cable of suitable size complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in replacement Aluminium bus bar of size 50 mm X 10 mm with aluminium thimbles nuts, bolts, washers etc complete all as specified and as directed by Engineer-in-charge Note- Aluminium bus bar strips shall be covered with PVC insulation tape of red , yellow, blue and black colour for proper colour coding as per IE rules. Cost of nuts ,bolts, washers, insulation etc. shall be inclusive in the quoted rates.

All as per item No. 284 here-in-before but Aluminium bus bar of size 50 mm x 6 mm

Supply and fixing in replacement Bakelite sheet 10 mm thick, ISI marked complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in replacement Isolator 4 Pole 100 Amp Make : ABB/Simens/Scheider/Legrand

Supply and fixing in replacement MCB 4 Pole 63 Amp Make : ABB/Simens/Scheider/Legrand

Material & labour wiring with PVC insulated stranded copper conductor cable 4.00 sqmm complete all as specified and as directed by Engineer-in-charge.

Material & labour wiring with PVC insulated stranded copper conductor cable PVC wire 6 Sqmm single core copper conductor

Material & labour wiring with PVC insulated stranded copper conductor cable 16 sqmm single core complete including suitable size of Luxes/thimble all as specified and as directed by Engineer-in-charge.

Cleaning and preparation of old painted surface of LT panel board complete and spray painting with two coat of synthetic enamel paint with appoved paint all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement MCCB, 63 Amps, 4 pole, 415 Volts, rupturing capacity not less than 25 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and double break fast tripping mechanism complete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.

Supply and fixing in replacement MCCB, 100 Amps, 4 pole, 415 Volts, rupturing capacity not less than 25 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and double break fast tripping mechanism complete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.

Supply and fixing in replacement MCCB, 160 Amps, 4 pole, 415 Volts, rupturing capacity not less than 25 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and double break fast tripping mechanism complete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.

Supply and fixing in replacement MCCB, 200 Amps, 4 pole, 415 Volts, rupturing capacity not less than 36 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and double break fast tripping mechanism complete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.

Supply and fixing in replacement MCCB, 320 Amps, 4 pole, 415 Volts, rupturing capacity not less than 36 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and double break fast tripping mechanism complete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.

Supply and fixing in replacement MCCB, 400 Amps, 4 pole, 415 Volts, rupturing capacity not less than 36 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and double break fast tripping mechanism complete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.

Supply and fixing in replacement MCCB, 630 Amps, 4 pole, 415 Volts, rupturing capacity not less than 50 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and double break fast tripping mechanism complete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.

Supply and fixing in replacement MCCB, 800 Amps, 4 pole, 415 Volts, rupturing capacity not less than 50 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and double break fast tripping mechanism complete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.

Repair of manual operated PF control panel / micro processor based automatic power factor control panel capacity of 21 KVAR to 500 KVAR fixed on various locations including testing, checking and repair and after removing deposited dust/seals/sludge and including taking out burnt/defective items and after fixing required necessary new items ie capacitor, MCBs, circuit wiring etc all as directed by Engr-in-Chaerge.

Supply only MPP type heavy duty power factor improvement capacitor (H/D ) with connector suitable for indoor/out door operation and provided with discharge resistors of rated voltage 440 v 50 HZ 3 phase with delta connection of rating 1 KVAR to 35 KVAR all as specified Make : L/T , SIEMEN Epcos

Supply only Push botton switch 6 A capacity 240 volts Make RAAS/Alfa/ Veeco

Supply only Miniature circuit breaker triple pole 40 Amp (C curve) 10 KA of capacity

Supply and fixing in replacement MCCB, 63 Amps, 3 pole, 415 Volts, rupturing capacity not less than 25 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and double break fast tripping mechanism complete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.

Supply and fixing in replacement MCCB, 100 Amps, 3 pole, 415 Volts, rupturing capacity not less than 25 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and double break fast tripping mechanism complete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.

Supply and fixing in replacement MCCB, 160 Amps, 3 pole, 415 Volts, rupturing capacity not less than 25 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and double break fast tripping mechanism complete withspreader link including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.

Supply and fixing in replacement LT current transformers of capacity 100/5,200/5,300/5,500/5, Amps Make Alfa/ AE/ Veeco

Panel mounted 3 Pole contactor of suitable rating operational voltage 500 volts, AC 50 HZ, inbuilt aux. contacts- 1 No + 1 NC or 2 NO + 2 NC with standard coil voltage 220 volts the surge resistor contract shall be post break type and damping resistances after closing be cut of current rating cap 15 Amp. Make :ABB/BCH/ Siemens/L&T

All as per item No. 309 here in before but rating of capacity 25 Apms.

All as per item No. 309 here in before but rating of capacity 40 Amps.

All as per item No. 309 here in before but rating of capacity 63 Amps.

All as per item No. 309 here in before but rating of capacity 100 Amps.

Supply and fixing in replacement APFC Relay 8 stage with built in multifuction meter for basic, THD and energy with 1 CT/3 CT sensing Option, smart switching, auto setup, THD protection, dual target PF, RS 485 communication, remote monitiring software complete all as directed by Eng-in-charge

All as per item No. 314 here in before but for 12 stage.

Dis connecting the LT servo seteblizer of cap 25 KVA to 200 KVA of any Make and repair of completeservo steblizer by taking out the main circuit plate, servo motors with gears, micro servo voltage controller, cable ,cable terminals etc ,including wiring and other minor parts, cleaning the complete accessories carefully. Minor repairs shall be rectified Parts/accessories shall be cleaned properly and refixing the parts at its original locations, checking and repair of the main circuit panel wiring with suitable size of wire and remove the carbon deposited inside the contact, cleaning all other spare parts all as directed by the Engineer-in-charge and reassembled after repair/replacement of following parts. Note: Spare parts as required for replacement of existing worm out parts shall be measured and paid separately under appropriate items Nos a to here-in-after as supply only.

Supply only servo motor for automatic voltage controller 220 Volts, 50 Hz 10 Kg cap

Supply only automatic voltage controller 220 Volts, 50 Hz

Supplying and filling new mineral grade transformer oil conforming to IS 3357 of 1983 for filling and for topping up in transformer duly filtered with filtration plant to obtain high dielectric strength not less than 40 KV (gap 2.5mm) complete all as specified and as directed by Engineer in charge.

M/S SHREE SHYAM TRADERS

B.K. ROY & SONS

BIDAWAT ENTERPRISES

M/s Chopra Associates