StartupTN Coimbatore

Amount

Brick work in Cement Mortar 1:3 (One cement and three crushed stone sand) using best quality Fly Ash Brick of size 230x110x75mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 including cost of mortar plasticizer, curing etc., complete complying with standard specifications and as directed by the TANSIDCO Engineers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally, other type of bond shall be done as directed by the Executive Engineer in charge. (As per TNBP No. 31)

Plastering the surface of walls with Cement Mortar 1:5 (One cement and five crushed stone sand), 12mm thick including mortar plasticizer at 200ml per 50Kg of cement used, curing etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (As per TNBP No. 56 & 57)

Plastering with Cement Mortar 1:3 (One cement and three crushed stone sand), 12mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including mortar plasticizer at 200ml per 50Kg of cement used, finishing, curing etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (As per TNBP No. 56 & 57)

Painting New Wood Work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works). (As per TNBP No. 66)

Painting two coats of newly plastered wall surface with ready mixed Plastic Emulsion Paint of first class quality and approved colour over a priming coat including thorough scrapping, clean removal of dirt wherever required etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (As per TNBP No. 66A)

Walls, Partition and Gypsum False Ceiling with putty

Ceilings without putty

Paving the floor with best quality Double Charged Vitrified Tiles of size 800 x 800 x 10mm and variety conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in Cement Mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works). (As per TNBP No. 39A)

Dadooing walls with the following best approved quality Tiles conforming to IS 15622 in Cement Mortar 1:2 (One cement and two crushed stone sand), 10 thick with mortar plasticizer and pointing the joints with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg / sq.m neatly in all floors, curing etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works). (As per TNBP No. 39A)

Double Charged Vitrified Tiles of size 600 x 600 x 8mm

Ceramic Tiles of size 300 x 600 x 10mm

Providing and fixing of Access floor systems of approved make confirming to PSA MOB - PF2 PS/SPU, BS 476 - Part 6, ASTM E84 1998 and ASTM E136 System: Access floor system to be installed shall provide a maximum finished floor height as mentioned below. The system shall provide suitable pedestal and under-structure designed to withstand various static loads and rolling loads. The entire Access floor system shall provide adequate fire resistance, acoustic barrier and air leakage resistance. Panels : Access Floor panel of size 600x600 mm shall be all steel welded construction, with an enclosed bottom pan of 64 hemispherical cones and top plain sheet which are fuse welded at minimum 81 locations to form a panel of an overall depth of minimum 29 mm. The inner empty core of the panel is injected with a light weight fire retardant, non combustible cementitious compound at high pressure to fill in all the crevices of the panel and ensures support of not less than 85% of the top surface area of the panel. The panel after cleaning, degreasing, phosphate by 7 tank process is coated with minimum 40 micron epoxy coat and is heated to achieve maximum adhesion and surface resistance. The Panels shall be UL listed / FM approved.

The panel is either bare finish or laminated with 1.5 mm thick fire retardant floor grade antistatic laminate / pvc on a semi -automated lamination line to ensure maximum bonding to the steel surface. The edges of the laminated/PVC are protected with black PVC edge trim 5mm wide on all sides. This edge trim is mechanically locked and sealed in place to avoid detachment. Pedestals : Pedestal installed to support the panel shall be suitable to achieve a finished floor height as mentioned below. Pedestal design shall confirm speedy assembly and removal for relocation and maintenance. Pedestal base to be permanently secured to position on the sub floor. Pedestal assembly shall provide for easy adjustment of levelling and accurately align panels to ensure lateral restrain. Pedestals shall support an axial load of 2000 Kgs, without permanent deflection and an ultimate load of 3500 Kgs. Pedestal head shall be designed to avoid any rattle or squeaks.

Pedestal Assembly : Consisting of 100 x 100 x 2mm thick galvanized epoxy polyester coated MS Base plate die-pressed orbitally riveted to a 21mm O.D. 2.5mm thick epoxy coated MS pipe to engage the pedestal head assembly. The pedestal head assembly consists of an embossed steel plate having 4 holes with ¼ the tapping for fastening and locating of tile ; orbitally riveted to a corresponding threaded stud 16mmdia. (O.D), length 100mm which is designed to engage the pedestal base assembly. The assembly shall provide a range of height adjustment upto 25mm, with the help of check nuts. Under structure : Under structure system consists of stringers of size 570 x 32x 20 x 1.5mm to form a grid of 600 x 600mm. These stringers are locked into the pedestal head and run both ways. The US system shall provide adequate solid, rigid and quiet support for access floor panels. The US system shall provide a minimum clear, uninterrupted height of 350 mm minimum, between the bottom of the floor and bottom of the access floor for electrical conduiting and wiring.

Stringers : Stringer system is all steel construction, rectangular channels 30 x 20 x 1.6mm thick with pre-punched counter sunk holes at both ends for securing the stringers onto the pedestal head ensuring maximum lateral stability in all directions. The grid formed by the pedestal and stringer assembly shall receive the floor panel. Panel Loading: The panel dimensions and performance must confirm with PSA MOB - PF2 PS/SPU standards for a heavy duty panel and must comply with the, Concentrated Point Load : 360 kgs on a 25 x 25 mm square on the center of the panel with a maximum permissible deflecting of not more than 2.5mm & Uniformly Distributed Load (UDL): 1650 kg/M2 with a maximum permissible deflection of not more than 2.0mm. Fire Rating : The Panels shall confirm to Class O & Class 1 Fire Ratings tested as per BS 476 Part 6 & 7.

Rate shall include to produce a test certificate for the above load of approved laboratory, preparation of surface, cutting for supply / return Air Grills and for Grommet of required size, wastages, lead & lift, grouting the system with anchor fastener, removing all debris from the premises etc. and for providing and applying of 500 micron Epoxy painting as a sub floor insulation to the entire area of existing floor(Below false flooring) as per manufacturer's specification etc., Complete complying with standard specifications and as directed by the deparmental officers. To a height of 300mm with Antistatic HPL finish

Supplying and fixing Teakwood frame for doors including labour charges for wrought and putup and fixing holdfast in frame etc., complete complying with standard specification and as directed by the TANSIDCO Engineers.

Scantling upto 2m length

Scantling above 2m to 3m length

Providing and fixing Solid core flush shutters with Teak ply on both side with teak wood lipping alround 35 mm thick. The shutter shall be made of solid core of block board type bonded with PF synthetic resin conforming to BWP grade of IS 848 with 6mm thick teak wood lipping as per drawing. The construction procedure of the shutter should be as per IS 2202. The shutter shall be shop prepared for taking mortice lock or latches suitable lock block of wood may be provided for fixing the hardware. The size of block, shall perfectly correspond to the maximum size of lock, covered in IS 2209. All the four edges of the door shutter shall be square. The shutter shall be free from twist or warp in its plane and of required size etc. complete as directed.

Rate shall include for cost of hardwares (aluminium hinges 125x30mm size - 3Nos. mortise lock With Night latch - 1 no. aluminium aldrop of size - 250x16 mm - 1No. Aluminium tower bolt of size 250x12mm - 1Nos. tower bolt of size 200x12mm - 1No, D type aluminium handle of size 200mm-2No., aluminium door stopper with nylon bush - 1No as required and fixing them all like lock, hinges, handle, tower bolts, and other accesories etc..as complete with all respects complying with relevant standard specification, as directed by the Departmental officers. Both sides of the door shall be finished with 1.0 mm thick laminate of approved colour / pattern.

Supply and Installation of Anodised Aluminium wide line frame of minimum size 100 X 25mm to a height of 2400mm maximum with proprietary Aluminium anodised frames all around the door with acoustic door seals, necessary wood inserts and rebate. The Profile shall be matt natural anodized, the profile manufacturer to supply all the necessary clips, seals and fixing accessories for the system. All profiles to be with 2 mm gauge thickness excluding 20 micron of anodizing. Rate to include all the works mentioned above including necessary accessories for fixing, anodised Aluminium back capping to suit the partition width., complete., Working at all levels and heights etc., Complete complying with standard specifications and as directed. Make: Dorma or Equivalent

Fabricating Supplying and fixing in position of Aluminium anodised Powder Coated (any colours) of single leaf fully glazed Door shutters with 5.50 mm thick glass. The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section with Vertical & Top rail: [email protected] kg/m, Bottom rail: 100x44.45x2.50mm@ 1.974 kg/m, Lock rail : 50x44.45x2.5mm @ 1.292 kg/mAlu. Clips: 17.15x17.27x1.50mm @ 0.176 kg/mAlu. Handle: 100x30mm @ 0.988 kg/m and necessary accessories such as Alu. clips rubber beading, full length of handles on one side, lock, furniture fittings such as, Hinges, rubber bush, including cost of materials, labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the reuired extent in RCC column, beam masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc. complete. All the Alu. Section are to be anodised with matt finish under electically contolled condition in accordance with IS 1868/1962 for an average anodic film thickness of 15 microns etc., complete.

Supply and erection of Double Leaves Fire Rated Door with Frame having the dimension of 1800mm x 1400mm with following specification: a. Door Frame 1.6mm: Galvanized 120 GSM branded make JSW b. Door Leaf 1mm: Galvanized 120 GSM branded make JSW c. Shutter Thickness: 46mm d. Honeycomb: In-fill e. Glue Macroplast UR-7221 f. Door Hinges: 4 x 3 x 3mm, Double Ball: Ball bearing Butt Hinges Grade SS 304 - Finish SS g. Door Closer with Standard Arm Finish: Silver h. Lock Set: Dead Lock with both side key i. Door Orientation: To be confirmed by client j. Mounting of door: Brick wall mounted k. Powder Coating: Powder coated in standard RAL paint colour of PO Red (60 to 90) Microns

l. Single Point Panic Bar (2 Horizontal) m. Dead Lock with both side key n. Vision Panel 200 x 300mm 2 Hrs. Fire Glass with Frame o. Rated Glass with Frame p. Anchor Bolt with Endcaps The above assembly mounted on concrete or brick wall including the cost of cutting, chipping, concrete packing, pastering, scaffolding all other conveyence as per standard methods and as directed by the Departmental Officers.

Gypsum Board Partition : Supplying and fixing of 10 mm thick Gypsum Board Partition to a thicknes of 50 mm which includes double side parition and providing 25 x 25 mm steel tube. The rate shall include the cost of gypsum board including making holes,cutouts, patch fittings, necessary hardwares, applying sealants, wastage etc, as required for completion the works and as directed by Engineer-in-charge.

Providing and fixing of 50mm thick Rock wool of density 48 kgs/m3 wrapped with 40GSM fiber glass tissue in drywall partition with holding clips to make it as acoustic proof. It shall be placed in the Aluminium frame cavity. The contractor must ensure that the wool is either wire-braced or holded with clips to prevent it from ‘lumping down’ over a period of time. Working at all levels and heights etc., Complete complying with standard specifications and as directed by the deparmental officers.

SINGLE GLAZED TOUGHENED GLASS PARTITIONS - WITH ALTERRRALITE SYSTEM-45 FRAME PROFILES Supply and Fixing of Slim Glass partition of 10mm Toughened Glass using Dormakaba Aterra liteSystem-45 Frames to a height of maximum 3m or as per drawing.The Fixed glass to be fixed using Dormakaba Aterra lite BP45 Profiles at Top & Bottom & Aterra lite SP45 at sides. The profile size to be 45x25MM to be fixed on to the floor/wall/ ceiling as per the architect design. Dormakaba Aterra lite H Junction profile to be used at all Glass to Glass vertical joints, 90 Deg L Junction Profiles and T Junction profiles necessary as per design.In case of Glass overall panel Alterralite MP45 & BP45 Overpanel Profile to be used.In case of Open glass edges EP45 End Profile to be used. The Aterra lite profiles shall be suitable for Glass thickness of 10/12/13.52mm.The Profile shall be matt natural anodized, the Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the system. All Profiles to be with 2 mm Gauge thickness Excluding 20 Micron of Anodizing. Approved Manufacturer: Profiles/Frames: Dormakaba, Glass : Saint Giobain/Asahi, Complete complying with standard specifications and as directed by the deparmental officers.

Designing, Printing, Supply and Fixing of Frost film to glass partitions using 3M frosted film stickers as per required pattern and shape and as directed. Cost inclusive of designing, mockup and installation with all accessories. The vendor must submit required warranty certificates from the manufacturer. Working at all levels and heights etc., Complete complying with standard specifications and as directed by the deparmental officers.

Supply & Fixing of Aluminium Glazed Door (Single Leaf) portal- 300x100mm for access control to open & close postion purpose switch fixing on the portal,The Profile shall be natural anodized / Powder coated in approved shade and finish, the Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the system. All Profiles to be with Excluding 20 Micron of Anodizing / 15 microns of powder coating etc. Approved Manufacturer: Profiles/Frames:

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval,

Including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification etc., including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed. but excluding the cost of painting with etc., Complete complying with standard specifications and as directed by the deparmental officers. 12.5 mm thick tapered edge Plain gypsum board - Any shape

Supply ,Installing, testing and commissioning of White color wall mounted European water closet with concealed dual flush tank with necessary pan connecter, bend,checknut, angle cock, solid seat cover with polythene buffer and flap, CP flanges etc.,complete. a) Supply ,Installing, testing and commissioning of EWC Wall Mounted Model no: Parryware C022W1C - Casa WHC Closet With SC Seat - White. b) Supply ,Installing, testing and commissioning of Concealed Concealed flush tank half frame & accessories. - C022Y1C - Casa WHC Cistern - White

Supply, Installing, testing and commissioning of Wash Hand Basin with all accessories such as Cast Iron Brackets, 32mm dia CP Waste Coupling, Rubber Plug and Chain, 32mm dia pvc Waste Pipe, 15mm dia brass ball Valve,15mm dia Nylon Connection, 15mm dia Brass Nipples,15mm CP sensor Pillar Tap etc White without Pedastal a) Under Counter Basin size: Parryware - Model : Wash Basin - C04711C - INDUS 500 X 400 - CTH ULTRAWHITE b) Supply ,Installing, testing and commissioning of Bottle Trap Bottle trap - T3201A1 - BOTTLE TRAP LIGHT c) Supply ,Installing, testing and commissioning of SS Waste Coupling Waste coupling - T9899A1 - Full Thread Waste Coupling- 80mm d) Supply ,Installing, testing and commissioning of Angle Valve - Angle cock - T9880A1 - Cute Angle Valve e) Supply ,Installing, testing and commissioning of Pillar Cock, - Sensor Pillar cock - Parryware - WPG541PA1

Supply, Installing, testing and commissioning of cp Health Faucet, with Rubbit Cleaning System, 1.00 m Long cp Flexible Tube & Wall Hook. a) Parryware Model : E8383A1 - Primo Health Faucet b) Supply ,Installing, testing and commissioning of Angle Valve - Angle cock - T9880A1 - Cute Angle Valve

Supply, installation and fixing of stainless steel toilet paper holder with SS screws on the wall. Make / Model : Parryware / T6914A1 - Comfort Paper Holder with Cover

Supply, installation and fixing of stainless steel body liquid soap dispenser with PVC rawl plug & C.P. brass screw complete as required. (Material : SS 304, Dispense : Foam soap, Battery : 4 x AA alkaline duracell, sensing distance : 5-9cm, Dispense volume : 1-2ml) Make : Make : Euronics -ES802F

Supply, installation and fixing of stainless steel body paper towel dispenser with SS screws on the breakout wall. (Cabinet : 18-8 stainless steel 304, Capacity : 450 (M & Z fold), 600 multifold) Make : Euronics - EP01

Supply, installation and fixing of C.P. brass twin coat hook with PVC rawl plug & C.P. brass screw complete as . Make / Model : Parryware /T5907A1 - Sigma- Twin Robe Hook

Supply, Installing, testing and commissioning of stainless steel sink without drain board , with 15m dia CP sink Cock , CP waste coupling, 32mm dia CP bottle trap with extension pipe, supporting CI bracket to support sink, and CP wall flanges, all complete set of approved make. . (Pantry) Make :Hafelei Stainless Steel splash Sink a) Supply ,Installing, testing and commissioning of Angle Valve - Angle cock - T9880A1 - Cute Angle Valve b) Supply ,Installing, testing and commissioning of Bottle Trap Bottle trap - T3201A1 - BOTTLE TRAP LIGHT c) Supply ,Installing, testing and commissioning of SS Waste Coupling Waste coupling - T9899A1 - Full Thread Waste Coupling- 80mm Make / Model : Parryware T4621A1 - Claret Wall Mounted Sink Cock

Supply, installation and fixing testing and commissioning of 25 ltrs approved make electically operated storage water heater inner container made from copper or stainless steel including the remal instalation safety valve, vacuum relief valve, neon lamp, mounting brackets, angle valve, connection hose installing in position with coach screws or bolts, nuts, testing, commissioning, etc, complete. Make & Model : AO smith - T4621A1 - Claret Wall Mounted Sink Cock

Supply and fixing of Wall mounted SS body Hand Dryer with SS screws on the wall. (Auto cutoff : 30sec, Sensor range : 12 cm - 15 cm, Hand dry time : less than 20 secs, Motor ; Brush type, dual ball bearings, Speed : 25,000 RPM, Rated power : 550 W, Current ; 2.5 A, Blowing volume : > 270 cum/hr, Air speed : 95 m/s , Operation : Touch free infra red activation) Make : Euronics - EH 26

Supply, iinstallation and fixing testing and commissioning of approved make angle cock (For RO) Supply ,Installing, testing and commissioning of Angle Valve - Angle cock - T9880A1 - Cute Angle Valve

Supplying, fixing and testing of approved make of 10kg / cm2 PVC pipes confirming to IS 4985-2000. and fittings (moulded and fabriacted fittings ) such as tee, elbow, 'y' , coupler, etc confirming to IS 7834 with latest amendment for soil and waste pipe works in toilets etc. Pipes shall be laid in under floors/ under ceiling / sunken floor as per approved drawings. For laying the pipes in walls, before chasing, the pipe line routing shall be marked using chalk line with help of tube level,Pipes and fittings shall be cleaned with pipe cleaners and joined by approved approved make solvent cement. After laying the pipes, before closing the pipes, gravity test to be conducted and got the approval from the engineers in charge

40mm dia

50mm dia

Supply and fixing , Testing and Commissioning of 6kg / cm2 PVC pipes confirming to IS- 13592 soil,waste & rainwater pipes jointed with solvent cement of good quality lubricant inclusive of all necessary specials like bends, tees, offsets, junctions, pan connector, cowls etc., laid under floor / under ceiling / on walls with suitable clamps including making bores in masonry etc., and rendering the bores in cement mortar after laying the pipes and specials curing etc., complete. The quoted rate should include necessary supports like hanger supports, grip bolts and clamps etc.,. Fixing of universal clamp for hanging pipeline is done at no extra cost and is included in the cost of installation of piping.(Brand & Specifications as per Design )

75mm dia

110mm dia

Providing & fixing in position deep seal multiway PVC floor Trap of size 100 x 75mm with cockroach trap and PVC extension piece of required length depth of following size to suit site conditions and multiple inlets, to suit site conditions with inlet sizes ranging from 40 mm to 75 mm. The bottom of the sump shall be dummied water tight. Wherever, sumps are shown to have water seal, the seal depth shall be minimum 40 mm. The sump shall be laid in cement concrete bed with 1:2:5 mix with 40 mm brick jelly bed all around and finished with cement mortar 1:3. Providing and fixing heavy class C.P. brass mosquito proof grating with frame of approved design including setting in floor with cement mortar to match with floor finish. ( Sample should be got approved ) include urinal trap

Supply, fixing and testing of PVC Floor cleanout (150x150mm). For removing Clogging, etc., complete. (The frame and grating shall be approved by Architects)

Supply and fixing of cockroach trap grating , complete as per specifications. (The item rate shall include all costs towards labour, tools, tackles & machineries, all leads & lifts, work related cleaning) complete. Square Drain Jali (5x5) "Angular"- Model No:F860058SS or equivalent

Supply, installation and testing of 20mm Dia CPVC pipes and fittings SDR-11 (upto 50mm dia) & SCH 80(above 50mm dia) conforming to ASTM D 2846. CPVC fusion compound shall conform tro ASTM F493. The scope of including, cutting, cleaning and fixing in/on walls under ceiling, on terrace, etc.,. The quoted rate shall include for making necessary chasing, making bores in foundation, walls, slabs, etc., and making good the chased surfaces and bores in cement mortar. Fixing of universal clamp for hanging pipeline is done at no extra cost and is included in the cost of installation of piping.(Internal Concealed,above ceiling piping , Shaft & terrace) (DWS, FWS & HWS)as directed by the depatmental officers

Supplying and fixing in position first quality and approved variety of 20mm Dia Gun metal gate valve / wheel valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications ( for both internal and external water supply arrangements). the valves to be used on work shall be got approved by the executive engineer before use on work.

Supplying, installing and testing 20mm Dia approved make Electromagnetic flow water meter with BMS compatibility including 3 Nos Ball valves for isolation and By pass with unions etc., complete. ( for both internal and external water supply arrangements). the valves to be used on work shall be got approved by the executive engineer before use on work.

Reception Table: Size - 2100 x 900 x 1050mm Table top : 25mm thick prelam particle board with grommet hole provision. Gable end & Front Panel : 18mm thick prelam particle board finish. Edge: All exposed area with 2mm thick PVC edge lipping. Including Pedestal unit.

Linear Workstation - Workstation Area - Sharing Size : 1200x 600 x750mm Table Top is made up of 25mm thick PLPB Table Top with 2mm PVC Edge Banding . Understructure : MS Powdercoated Legs 40 x 40 Slant legs. Wire Management : Grommet Hole -65mmDia 250mm ( Ht ) Raceway below the table top Main Screen : 18mm Thick & 300mm(ht) fabric magnetic privacy with rubber beading. CENTER T LEG : MS 40X40 MS 40X40 Square leg with CRCA Pipe of 1.6mm thickness of 60 microns Powder coated leg for Table top Stability. Passage side modesty : MS powder coted 450mm(ht)

Cabin Table: Main Table Size - 1500 x 750 x 750mm Side Storage Size - 900 x 450 x 750mm Back Storage Size - 2600 x 450 x 750mm Main & Side table Specifications: Top panel: 25mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping LEG : Slant or Straight leg 40*40mm size tube, tube thickness 1.6mm with powder coating finised. SUPPORT BEAMS : 40*40mm ms tube with 1.6mm thickness and with ms powder cioating finished. MODESTY : 1.2mm Thk ms modesty panel with powder coating finished in 400mm height. Flip cover 400mm PLB SIDE & BACK STORAGE UNIT Top & Sides: 18mm Thk pre laminated particle board Back: 6mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping FASCIA: 18mm Thk pre laminated particle board. Handle: I shape handle Lock: Key lock

WORKSTATION CHAIRS. AURA - Medium Back •Sturdy 50mm G.F Nylon dual- wheel Castors , •Glass Filled Nylon Base , •Class 4 Gas lift as per DIN Standards 4550: 2004-12 , •Single Position Locking Synchro Mechanism , •Height Adjustable 2D PU Armrest, •Glass Filled Nylon Backrest with Mesh , •Seat Upholstered with PU Foam & Fabric , • Height Adjustable Lumbar Support.

Visitor Model Meshback Chair S type Fixed Handle

Cabin Table: Main Table Size - 2100 x 100 x 750mm Side Storage Size - 2000 x 500 x 750mm Back Storage Size - 2700 x 450 x 750mm Main & Side table Specifications: Top panel: 25mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping LEG : Slant or Straight leg 40*40mm size tube, tube thickness 1.6mm with powder coating finised. SUPPORT BEAMS : 40*40mm ms tube with 1.6mm thickness and with ms powder cioating finished. MODESTY : 1.2mm Thk ms modesty panel with powder coating finished in 400mm height. Flip cover 400mm PLB SIDE & BACK STORAGE UNIT: Top & Sides: 18mm Thk pre laminated particle board Back: 6mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping FASCIA: 18mm Thk pre laminated particle board. Handle: I shape handle Lock: Key lock

Main Chairs: Imported Half Leather Chair Fixed handle,Synchro Tilting Mechanism,Imported Gaslift,Chrome base,Heavy

Board Room Table: Size - 6750 x 1650 x 750mm V - SHAPE MEETING TABLE Table top is made of 25mm thick Pre.Lam particle board with 2mm PVC Edge banding UNDER supported on Mild steel Powder coated legs. MS 40X40 Square leg Powder coated leg for Table top Stability. INTERMEDIATE COVERED LEG : Made of 1.6 mm Thick Top bar and Cover Stump of 0.9mm Thick Mild steel Sheet Powder coated to 60 Microns, Covered stump stump 450/600mm width considered for wire accessing from floor to raceway. MS CONNECTOR: 40X40 mm Square CRCA Pipe of 1.2mm thickness of 60microns Powder coated connector for Table top support. WIRE MANAGEMENT : FLIP UP BOX 150MM(HT) CABLE DUMP BELOW TABLE TOP METAL PERFORATED MODESTY PANEL - ONLY MAIN CONSIDERE 450 MM HT . Made of 1mm thick Mild steel sheet with 60microns Powder coated Modesty panel provided below the table top privacy.

BOARD ROOM CHAIRSWEBSTAR: Medium Back with Adjustable Handle & softpad with Chrome Base,Heavy Wheel, Synchro Tilting Mechanism,Molded Foam & Fabric

Conference Table: Size - 3150 x 1200 x 750mm TABLE TOP :25mm Thick Pre Laminated particle Board with 2mm PVC edge banding on all side with Flip Cover Hole Provision. (400mm Flip Cover). LEG : Slant type Legs, Tube thickness 1.6mm with ms powder coating finish. Cable entry Box Provided. Supported Cross Bar 40*30mm Size tube with 1.5mm thick sheet and powder coating finish. Below Table top Box Type Raceway.

ROUND MEETING TABLE Size - 900mm dia, 750mm height Top : 25mm Thk pre laminated particle board with Pop box provision. Edge: All exposed area with 2mm thick PVC edge lipping Understructure : ms slant leg with powder coated

Training chars with writing pad

Low Height Storage: Size - 5750 x 600 x 750mm PLB STORAGE UNIT Specifications: Top & Sides: 18mm Thk pre laminated particle board Back: 6mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping FASCIA: 18mm Thk pre laminated particle board Handle: I shape handle Lock: Key lock

Printer Storage: Size - 4650 x 600 x 750mm PLB STORAGE UNIT Specifications: Top & Sides: 18mm Thk pre laminated particle board Back: 6mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping FASCIA: 18mm Thk pre laminated particle board Handle: I shape handle Lock: Key lock

Full Height Storage: Size - 1650 x 450 x 2100mm PLB STORAGE UNIT Specifications: Top & Sides: 18mm Thk pre laminated particle board Back: 6mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping FASCIA: 18mm Thk pre laminated particle board Handle: I shape handle Lock: Key lock

Pantry Unit: Size - 6000 x 600 x 800mm Supply and installation of Counter for Pantry and Cafeteria, The storage of countertop to be made of 19mm BWR ply with necessary. The storages to be with shelves, made of 19mm thick BWR ply with swing shutters with all necessary accessories like concealed auto closing SS hinges,

Pantry Table: Size - 900 x 900 x 750mm Top : 25mm Thk pre laminated particle board with Pop box provision. Edge: All exposed area with 2mm thick PVC edge lipping Understructure : 40*40 Square leg with ms powder coated.

Pantry Table: Size - 1500 x 750 x 750mm Top : 25mm Thk pre laminated particle board with Pop box provision. Edge: All exposed area with 2mm thick PVC edge lipping Understructure : 40*40 Square leg with ms powder coated.

Plastic chair for pantry

3 Seater sofa for reception

Center Table: Size - 1200 x 600 x 400mm Table top 18mm thick prelam particle board with edge banding finish. Leg 20mm square ms leg with powder coating finish.

Corner Table: Size - 600 x 600 x 400mm Table top 18mm thick prelam particle board with edge banding finish. Leg 20mm square ms leg with powder coating finish.

Fabric seater with cushion and with wooden legs for CEO room

Center Table: Size - 450mm dia, 400mm height Table top 18mm thick prelam particle board with edge banding finish. Leg 20mm square ms leg with powder coating finish.

Poof - Fabric finish

Fabric seater with cushion and with ms legs

Center Table: Size - 600mm dia, 400mm height Table top 18mm thick prelam particle board with edge banding finish. Leg 20mm square ms leg with powder coating finish.

18mm thick writing board of size 1200 x 1500mm with ms movable stand.

Bar Stool

Transportation, loading and unloading charges

Supply and fixing of 7 segment 6 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type / surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in each segment) and seperate provision for MCB / Isolators ( totally 18 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following on wall with earth connection only. 1. 63A 4P MCB - 1 no. 2. 40A DP 30MA RCCB/ELCB - 3 nos. 3. 6A to 32A SP MCB - 18 nos.

Supply & fixing of NUMERIC LEGRAND –HPI 33 EVO 20KVA FMI with Isolation transformer (3Ph-3Ph) 12V/240 VDC, Online Double Conversion UPS including MS rack for housing the batteries along with necessary interconnection cables. Warranty: 2 Year for UPS 12V / 42 AH / 20Nos of SMF Batteries 30minutes backup timing Make: EXIDE/QUANTA Warranty: 2 Years for SMF Batteries.

Supply and Run of 4 of 16 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable gauge MS conduit pipe on wall and ceiling with continuous earth wire connection of 16 sq mm copper wire with painting of suitable colour.

Supply and Run of 4 of 16 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC flexible hose on wall and ceiling with continuous earth wire connection of 16 sq.mm copper wire with painting of suitable colour.

Earthing as per PWD standard with an earth electrode of 2 metre Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with painting of Suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for Open MS conduit Light point / fan point (for electronic regulator) (5 points / Coil) Lower End

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with suitable Module GI switch box on wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with painting of Suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for Open MS conduit Plug point Lower End

Supply and fixing of 30W 2x2 LED square Recessed type fitting with suitable frame wherever necessary on false Ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 19W LED Round Recessed type fitting on false Ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 3 nos. 6A two module 3 pin socket, 1 nos. 6A one module switch with suitable module cover plate (plastic) on existing wall / Truf / Box beneath the table with connections. Lower End

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch on suitable module surface mounting Box (Plastic) with module cover plate (plastic) on wall with connections. Lower End

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC flexible hose on wall and ceiling with continuous earth wire connection of 1.5 sq.mm copper wire with painting of suitable colour

Supply and run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable heavy gauge MS coundit pipe on wall and ceiling with continous earth wire connection of 2.5 sq.mm copper wire with painting of suitable colour

Supply and Run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper wire and making good of the concealed portion.

VRF SYSTEM Note: VRF Units shall meet minimum efficiency requirements as per latest ECBC norms. EER & IEER values as specified in ECBC to be met or as per latest BIS standards, if they are more stringent. Air Cooled VRF System Supplying, installation, testing and commissioning of Air Cooled Variable Refrigerant Volume System suitable for R410A and 415V, 50 Hz, AC supply. The unit shall consist of indoor units and external condensing units and other accessories complete in all respects. The unit shall be fully charged with gas and oil. Outdoor Unit Supply & Installation, testing and commissioning of Outdoor units consists of 100% inverter compressors, condenser fan motor with variable speed controllers & aero-spiral fan blade and, e-pass heat exchanger, safety valves, solenoid valves, receiver, capillary tube, check valve, electronic expansion valve, high pressure switch, low pressure sensor, pressure regulating valve, refrigerant filter, stop valve, accumulator and refnet kits. The COP of the VRF system shall be minimum 3.5 at AHRI condition. Rate shall be inclusive of R-410A refrigerant & oil pre charging, vibration isolators, supports, necessary mounting brackets/ pedestal works etc.

The outdoor unit shall be sized to deliver following rated capacities at 40 deg C ambient condition which excludes de-rated capacity due to excess length of refrigeration pipes, change in indoor dry bulb & wet bulb temperature. All the compressors shall be rated for continuous operation. As per specification & tender drawings. All the units shall be provided with built-in microprocessor control panel, for automatic operation and capacity control. Machines shall be suitable for working with BMS system. Each VRF module must have accumulator to handle liquid and safe guard compressor against liquid flood back due to dynamic load condition. VRF system shall have auto Restart function i.e. In case of power failure, units should restart automatic when power resume. VRF system shall have auto bypass i.e. If any one IDU have any electric or PCB failure, rest of the system should continue to operate. The VRF system shall have free phase technology, which shall correct phases automatically in case of phase reversal. Below Mentioned single ODU Models should be able to make module combination (16 HP+16HP +16 HP) Make : Daikin, Voltas, samsung ,LG & Hitachi

VRF-Hi Wall Split units Supplying, installation, testing and commissioning of Wall Mounted Type Metallic body Indoor Units each complete with coil, filter, cordless remote etc. Air conditioners with evaporating unit comprising of cooling coil, blower with motor and 220 volt, 1 phase, 50 Hz, AC supply all and as per specifications. The rate will also include for complete indoor unit supports.

VRF-4 Way cassette units Supplying, installation, testing and commissioning of Ceiling Suspended Cassette Type Metallic body Indoor Units each complete with coil, filter, etc. Air conditioners with evaporating unit comprising of cooling coil, blower with motor and 220 volt, 1 phase, 50 Hz, AC supply all as per specifications. The rate will also include for complete indoor unit supports

VRF- DUCTABLE UNITS Supplying, installation, testing and commissioning of Ceiling Suspended ductable Indoor Units each complete with coil, filter, etc. Air conditioners with evaporating unit comprising of cooling coil, blower with motor and 220 volt, 1 phase, 50 Hz, AC supply all as per specifications. The rate will also include for complete indoor unit supports 8.0 TR

Refrigerant Joints and Headers Supply, installation, testing, and commissioning of Imported fittings Y-joints, distributor and headers for all Indoor units as per layout drawings.

Refrigerant Piping for VRV system Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable size cable tray/adjustable ring type hanger supports, jointing/brazing including accessories, insulated with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines & cladded with 26G aluminium sheet. all accessories as per specifications etc. as required. All connections of Refrigerant piping shall be in high grade Copper of Refrigeration quality with Eddy Current Testing and material test Certificates.

6.40 mm dia

9.50 mm dia

12.70 mm dia

15.90 mm dia

19.10 mm dia

22.20 mm dia

Refrigerant Piping for VRV system Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable size cable tray/adjustable ring type hanger supports, jointing/brazing including accessories, insulated with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines & cladded with 26G aluminium sheet. all accessories as per specifications etc. as required. All connections of Refrigerant piping shall be in high grade Copper of Refrigeration quality with Eddy Current Testing and material test Certificates.

25.40 mm dia

28.60 mm dia

31.75 mm dia

36.90 mm dia

41.30 mm dia

DRAIN PIPING Supply and erection of following Heavy Duty PVC pipe with all joints, reducer, necessary elbows and tees, supporting arrangements, etc.

40 mm dia

32 mm dia

25 mm dia

Transmission & Control Wiring Supplying, installing, testing and commissioning of Shielded control cum transmission wiring of 2 core x 1.5 sqmm copper FRLSH, XLPE insulated Unarmoured cable in suitable GI conduits accessories between indoor and outdoor units. Necessary securing of conduit shall be made by contractor. After completion of work wall and floor shall be repaired and brought to its original finish. The rate will also include cost of laying of GI conduit between indoor and outdoor units.

GAS Charging Providing additional R410A gas charging for the ODU units

PERFORATTED TYPE CABLE TRAY Supply and fixing of Profile design Cable Perforatted type with horizontal & vertical bends, reducers, Tee's,Cross over, supports, brackets and other accessories as required confirming to IS/ IEC-61537.The Cable tray shall be made of 1.6mm thick.The cable tray shall be powder coated/ Pregalvanized for corrosion protection confirming to DIN EN 10346 / ISO 1461 .The cable ladder should be tested for safe working load with a span distance of 2.4 Mtr and the deflection should be within the limits as per the NEMA standard. The cable tray shall be supplied in standard length of 2500 mm. The rung size shall be 35x15 size & the space between the rungs shall be 300mm. The trays shall include necessary Couplers. 150mm wide 50mm height

DRAIN PUMP Supply, Installation,testing and commissioning of AC Drain Pump with accessories

GI FLAT OVAL DUCT WITH PRE INSULATION: Supply, Installation, Testing & Commissioning of air distribution system consists of factory fabricated GI sheet Flat Oval (elliptical) duct with pre insulated 13 mm thickness nitrile rubber FM approval factory made fittings like bends, tees, wire hanging support with crimp arrangement supports, spacing and fixing as per SMACNA standards. The rate shall be inclusive of powder coating (Mat finish) for the ducts as per the approved colour shade by Client / Architect.

22 Gauge – factory fabricated

24 Gauge – factory fabricated

Supply, Fabrication and erection of fabricated ducting made up of GI Sheets of 24 Gauge thickness 24 Gauge – factory fabricated

Supply and fixing of extruded aluminum powder coated, Supply and return Air Grilles / Diffusers with Volume Control Damper

Supply and installation of GI volume control damper (Rectangular / oval) low leakage( handle type ) made out of 1.6mm thick galvanised sheet steel frame and opposed blades of 1.6mm galvanised steel with suitable links, handles, levers and quadrants for manual control of volume of air flow and for proper balancing of air distribution system.as per specification

Supply, installation and testing of round flexible duct inner core should be made of triple lamination of Aluminium Foil, Polyester & Metalized polyester film permanently bonded to a coated spring steel wire helix. Fiberglass insulation shall be of 25mm thick with minimum density of 16 kg/m³. The outer insulation jacket vapor barrier shall be made of fiber glass reinforced metalized polyester film laminated with aluminium foil as per the technical specifications. The rate shall be inclusive of hose clamps, supports,bolt,nut etc. AS per specification.(1.2 Mtr) 100mm Dia

Supply, installation testing & commissioning of Butterfly damper should constructed with Not less than 0.8mm thick galvanized steel sheet, with single flap, necessary stopper, flanges, grooves 150-mm length, neoprene gasket at the edge of blade to reduce leakage and with required hardware and accessories as per specification. Include locking device to hold single-blade dampers in a fixed position without vibration & engraved marking on position of damper, as per specifications. 100mm Dia

Supply, Installation, Testing & Commissioning of air distribution system consists of factory fabricated GI sheet circualr duct

1750 Cfm -15mm external static cabinet type fresh air fan with prefilter & necessary supports

400 Cfm - 15 mm external static Inline fan with all necessary supports. (Pantry exhaust). Fan shall be provided with in built fan regulator.

150 Cfm - 15 mm external static single skin Inline fan with all necessary supports. (Battery room exhaust).

150 Cfm - Propeller type fan with all necessary supports. (Toilet exhaust).

Supply & laying of CAT-6 cable

Supply & clamping of 25mm PVC pipe

Supply & fixing of RJ45 socket with suitable cover plate

Supply & fixing of 42U Rack with 2 Nos. of Fan, 1 No. of Server /IT Rack mount power distribution unit, 1Ph, 230V, 50/60Hz, 2U standard with 6 X Indian socket 5A, Inlet Plug type 6A Indian Plug, 8A Fuse, 1 No. of Tray and necessary accessories

Supply & fixing of Fully Managed 10 / 100 / 1000 Layer-2 Network Switch with 1G Uplink - Higher End/24 Port with 4 Nos. of Fibre Port

Supply & fixing of 8Port PoE switch for CCTV IP Camera

Supply & fixing of 24 Port Patch Panel – Fully Loaded

Supply & fixing of 1 mtr. Patch cord for rack end & user end

Supply & fixing of D-Link DAP-2680 Wireless AC1750 Wave 2 Dual-Band PoE Access Point features cutting-edge Wave 2 technology that brings greater speeds, efficiency, and security to your wireless customers.

Supply & fixing of Pop-up box with 2 Nos. of 6A socket, 1No. of switch, 1No. of RJ45, 1 No. of RJ11 and 1 No.of HDMI ports (Legrand)

Supply & laying of 10mtr. HDMI cable

Supply & fixing of 8 Channel - 1 SATA Network Video Recorder which should support minimum of 5MP Camera

Supply & fixing of 4 TB Hard Disk for NVR

Supply & fixing of 4 MP IP Dome Camera

Testing, Commissioning & Dressing of switches, patch panels & other components in the Rack with tagging & connection complete

Supply & installation of Biometric device Make: ESSL Model: K30 Pro Features: Finger print capacity - 2000 Card capacity - 10000 Finger print sensor - 500 DPI optical With Battery backup

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity with 5 years warranty as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc, complete as per standard specification and as directed by the SIDCO Officers.

Supply and fixing of Carbon-di-Oxide Gas Type 4.5 kg. capacity Fire Extinguisher with 5 years warranty as per New IS15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc., complete as per standard specification and as directed by the SIDCO Officers.

FE36 Automatic ceiling Mounted Clean agent Extinguisher - 5 Kg with Ceiling mount accessories including nozzle(57 deg), pressure guage. ISI approved - batttery (1)

MRP Constractors (BID ID -1508922)

G ILANGUMARAN (BID ID -1509012)

Boson Infra India Private Limited (BID ID -1508684)