WELCOME MAINT AND REPAIR TO FLOORING, KITCHEN CUP BOARD, JOINERY, PLUMBING AND CERTAIN BR WORKS AT MD ACCN IN ZONE-I AREA UNDER GE (A) JAISALMER

Amount

M&L preparation of old decorated wall surfaces of any description and applying one coat of white wash complete all as specified & directed by Engineer-in-charge.

M&L preparation of old decorated ceiling surfaces of any description and applying one coat of white wash complete all as specified & directed by Engineer-in-charge.

M&L perpartion of old existing wall surfaces including cornices, plastered or un-plastered surfaces by brooming down or steel wire brushing, moss efflorescent salt and trading oil and greasy spots and applying one coat of cement base paint over and including filling up of holes by wall care putty wherever required complete all as specified & directed by Engineer-in-charge.

M&L preparation of old decorated wall surfaces of any description and applying one coat of oil emulsion distemper complete all as specified & directed by Engineer-in-charge.

M&L preparation of old decorated by complete removal of existing treatment wall surfaces over a coat of alkani resistant primer of any description and applying two coat of oil emulsion distemper complete all as specified & directed by Engineer-in-charge.

M&L preparation of old decorated wall surfaces and apply 3mm thick wall care putty for smotth and plain surface of wall complete all as specified & directed by Engineer-in-charge.

M&L preparation of old decorded wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed by Engineer-in-charge.

M&L preparation of old decorded steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed by Engineer-in-charge.

Taking down cement plaster from brick or concrete wall surfaces including raking out joints, hacking for key scrubbing down with water complete all as specified & directed by Engineer-in-charge.

M&L rendering 15 mm thk on brick or concrete surface in CM 1:6 and surface finished even and smooth without using extra cement complete all as specified & directed by Engineer-in-charge.

M&L for 10mm thick rendering in cement morter 1:4 on fair face of brick wall or concrete surfaces, finished even & fair complete all as specified & directed by Engineer-in-charge.

M&L for 5mm thick rendering in cement morter 1:3on ceiling, finished even & fair complete all as specified & directed by Engineer-in-charge.

M&L for preparation of newly plastered surfaces and applying two coats of cement based paint over a coat of alkali resistant paint complete all as specified & directed by Engineer-in-charge.

M&L preparation of new plastered surfaces of any description and applying two coats of oil emulsion distemper over a coat of wall putty on wall and chalk whiting prepara-tory to distempering complete all as specified & directed by Engineer-in-charge.

M&L preparation of new plastered surfaces of ceiling any description and applying three coats of white wash complete all as specified & directed by Engineer-in-charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing, removing serviceable tiles) complete all as specified & directed by Engineer-in-charge.

M&L for 25mm thk PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in subbase of floors & finishing the surface even & smooth without using extra cement complete all as specified & directed by Engineer-in-charge.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including scread bed or bedding layer 15mm thick in CM 1:6 complete all as specified & directed by Engineer-in-charge.

M&L for vetrified ceramic coloured tiles 9 to 10 mm thick area of each tile not exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement over 15mm thick screed bed in CM 1:6 all as directed (size 600mm to 600mm) complete all as specified & directed by Engineer-in-charge.

M & L non skid ceramic coloured tiles 7-8mm thick(square/rectangular) area of each tile exceeding .11Sqm but n.exc .18Sqm in floor set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick screed bed in CM 1:6 complete all as specified & directed by Engineer-in-charge.

M & L glazed ceramic coloured tiles (450x300mm)x 7mm thick joint free in dado/skirting set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in CM 1:4 etc complete all as specified & directed by Engineer-in-charge.

Taking down shutters of any description not exc 1 Sqm each complete all as specified & directed by Engineer-in-charge.

Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm each complete all as specified & directed by Engineer-in-charge.

Taking down chowkat (without taking of shutter from the frame) not exc 1.5 sqm each including making good the disturbed surface in PCC 1:2:4 type B0 or CM 1:3 and white wash and cement base paint complete finished complete all as specified & directed by Engineer-in-charge.

All as per item No 24 above but exc 1.5 sqm and n exc 4 sqm each

S & F factory made second class hard wood plain framed panelled shutters 35mm thick with panels of timber flat on both sides (feather edged) or of veneered particle board medium density wood particle tone veneers, fixed to chowkhat complete all as specified & directed by Engineer-in-charge.

S & F Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats second class hard wood 35mm thick for door shutter complete all as specified & directed by Engineer-in-charge.

S&F Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M S square tubes, S&F in opening as per specification & drawing given in SSR 2010.

M & L for factory made solid PVC moulded door shutter , 28 to 30mm thick (stiles) wuth 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on the foront face & 2mm plain colour PVC sheet on back face supplying and fixing in frame at site as per specification & drawing.

S & F aluminium anodized tower bolt 150mm size complete all as specified & directed by Engineer-in-charge.

S & F Butt hinges Aluminum 100 mm type C21 complete all as specified & directed by Engineer-in-charge.

S & F aluminium handle 125 mm cast type anodized complete all as specified & directed by Engineer-in-charge.

S & F mild steel sliding bolt 300 mm long plate type stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fix complete all as specified & directed by Engineer-in-charge.

S & F steel windows with side hung shutters including projecting type hinge with steel handle and steel peg stay, complete with glazing bars, devetailed or welded complete all as specified & directed by Engineer-in-charge.

S & F figured glass pin head type 3mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified & directed by Engineer-in-charge.

S & F sheet glass 3mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified & directed by Engineer-in-charge.

S&F Galvanized mild steel wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanized wire staples fixed complete all as specified & directed by Engineer-in-charge.

M&L for Anodised aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc complete all as specified & directed by Engineer-in-charge.

M&L for Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etccomplete all as specified & directed by Engineer-in-charge.

Sheet glass, 4.80 mm ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane complete all as specified & directed by Engineer-in-charge.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty approved by Engr-in-Charge

S&F aluminium die cast body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed approved by Engr-in-Charge

S & F in repair anodised aluminium alloy Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified & directed by Engineer-in-charge.

Dismantling boarding of any description fixed in any position fixed with screws complete all as specified & directed by Engineer-in-charge.

S & F 18/19mm thick pre-laminated particle board, exterior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination alround 6mm th teak fillets fixed in kitchen CB or pelmet complete all as specified & directed by Engineer-in-charge.

M&L for 2nd class hard wood fillets square, rectangular as in lippings fixed with nails of area exc 3Sqcm but n.exc 6sqcm complete all as specified & directed by Engineer-in-charge.

S & F 40mm width of flaps (when open) continuous (piano) hinges, mild steel bright finish or electroganised fiwed to wooden or angke iron frame complete all as specified & directed by Engineer-in-charge.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified & directed by Engineer-in-charge.

S&F in repair, 100 mm size hasp and staple, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws and fixed complete all as specified & directed by Engineer-in-charge.

S&F in repair 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified & directed by Engineer-in-charge.

Dismantling water tanks and removing to store (exc 250 and not exc 500 ltr capacity) complete all as specified & directed by Engineer-in-charge.

Dismantling water tanks and removing to store (exc500 and not exc 1000 ltr cap) complete all as specified & directed by Engineer-in-charge.

S&F 500 ltrs capacity white colour three layer rotational moulded polythene water storage tank (Cylinderical vertical with closed top) hoisted and fixed in postion complete all as specified & directed by Engineer-in-charge.

S&F 1000 ltrs capacity white colour three layer rotational moulded polythene water storage tank (Cylinderical vertical with closed top) hoisted and fixed in postion complete all as specified & directed by Engineer-in-charge.

S&F in repair CP bib taps 15 mm dia of cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge.

S&F in repair pillar taps 15 mm bore cast copper alloy with capstan head chromium plated screwed down high pressure with or without 'Hot' & 'Cold' with long screwed shanks and fly nuts, screwed complete all as specified & directed by Engineer-in-charge.

S&F in repair stop valve 15 mm bore cast copper alloy screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for union complete all as specified & directed by Engineer-in-charge.

S&F in repair stop valve 20 mm bore cast copper alloy screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for union complete all as specified & directed by Engineer-in-charge.

S&F in repair vitreous china squatting pan orissa pattern complete of size 580 x 440 mm white with integral foot rest and making good to the floor complete all as specified & directed by Engineer-in-charge.

S&F in repair wash hand basin vitereous china flat back size 550 x 400 mm white incl CP waste coupling waste pipe brackets complete all as specified & directed by Engineer-in-charge.

S&F in repair PVC low level white flushing cistern syphonic action type 10 ltrs capacity incl flush pipe 32 mm dia incl PVC connection 450 mm long complete all as specified & directed by Engineer-in-charge.

S & F in repair 32 mm dia., Waste fittings, brass chromium plated for glazed ware sinks, wash basins etc., with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end complete all as specified & directed by Engineer-in-charge.

S&F in repair PVC connection pipe for WHB, cistern, gysers etc of size 15 mm dia and 450 mm long fixed complete all as specified & directed by Engineer-in-charge.

S&F in repair CP grating(with & without hole) for Nahani trap and floor trap of size 100 mm dia fixed complete all as specified & directed by Engineer-in-charge.

Cutting chases for concealed water tubing etc and making good in CM cutting exc 10 cm but not exc 20 cm girth in stone, concrete block or slab walls complete all as specified & directed by Engineer-in-charge.

S&F in repair Swivel shower rose with arm 195mm long with bend of 45 degree with flange of PTMT any colour fixed complete all as specified & directed by Engineer-in-charge.

S&F, in repair, ball valves for 15mm bore pipe, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball complete all as directed by Engineer-in-charge. (minimum weight 142 gms) complete all as specified & directed by Engineer-in-charge.

S&F, in repair, ball valves for 20mm bore pipe, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball complete all as directed by Engineer-in-charge. (minimum weight 210 gms) complete all as specified & directed by Engineer-in-charge.

S & F in repair Vitreous china wash down water closet pan(Pedestal pattern), white (EWC) with necessary P/S Trap and fixed in repairs including jet spray and seat cover complete all as specified & directed by Engineer-in-charge.

S & F in repair Vitreous china wash down one piece water closet pan(Pedestal pattern), white (EWC)with necessary P/S Trap and fittings fixed complete all as specified & directed by Engineer-in-charge.

S&F in repair, tubular towel rail brass chromium plated, 20mm dia, D type, 60cm long between flanges fixed with chromium plated brass screws complete all as specified & directed by Engineer-in-charge.

S&F in repairs soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified & directed by Engineer-in-charge.

S&F Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified & directed by Engineer-in-charge.

S&F in repair toilet paper holder of brass, chromium plated fixed to walls with chromium plated (CP) brass screws complete all as specified & directed by Engineer-in-charge.

S&F in repair PVC acrylic shelf for WHB 450 mm long complete all as specified & directed by Engineer-in-charge.

S&F in repairs Vitreous china urinals with urinal spreader, half stall (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing or complete all as specified & directed by Engineer-in-charge.

S&F in repair PVC seat cover black/white closed pattern with flat bottom and mild steel CP or aluminium hinging device complete all as specified & directed by Engineer-in-charge.

S&F in repair bathroom mirror cabinet, make Prayag or equivalent approximate size 500x400mm complete all as specified & directed by Engineer-in-charge.

S&F in repair Stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm complete all as specified & directed by Engineer-in-charge.

S&F in repair Stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm complete all as specified & directed by Engineer-in-charge.

S&F in repairs Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed for 15mm dia bore complete all as specified & directed by Engineer-in-charge. Note-Prayag Cat no. 9575 or equivalent

S&F in repair two way angle valve for fixing in 15mm dia bore complete all as specified & directed by Engineer-in-charge.

S&F in repair Health Faucet for EWC all as specified and directed Note- Cat no. Prayag BEA-41 or equivalent

Taking up or down steel tubing and connections of following size all as directed by Engg-in- Charge :-

(a) 15 mm bore

(b) 20 mm bore

S&F GI tubing (ISI) marked) medium grade with all fitting and fixed complete to wall ceiling or laid in floors of following sized :-

(a) 15 mm bore

(b) 20 mm bore

Refixing old steel tubing including cleaning and connections in new or old position (Wall, ceiling, floors etc) of the following size :-

(a) 15 mm bore

(b) 20 mm bore

S&F in repair 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified & directed by Engineer-in-charge.

Hacking out old broken glass of any thickness size,quality or description from any type of frames and S&F 3mm thick sheet glazing in square n.exc 0.5 sqm ordinary quality with glazing clips and oil putty complete all as specified & directed by Engineer-in-charge.

Demoiliton of stone slabs and tiles of any description or thickness in foors, aprons etc complete all as specified & directed by Engineer-in-charge.

M&L Granite (of any type) tile 16 to 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing laid on complete all as specified & directed by Engineer-in-charge.

M&L Granite (of any type) tile 16 to 20mm thick machine cut,in skirting/dado laid over cement screed bed and jointed with cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified & directed by Engineer-in-charge.

Dismantling Trellis work (Jafri), including taking as under of battens in trellis (posts and rails measured separately) complete all as specified & directed by Engineer-in-charge.

M&L for 35mm thick precast cement concrete louvers and jallies type C-0 (1:3:6) using 12.50mm graded aggregate (measured solid), including all mouldings but excluding frame, set in cement mortar 1:4 complete all as specified & directed by Engineer-in-charge.

M& L Providing type B1 (1:2:4) (20mm graded aggregate) precast ce- ment concrete in win- dow or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps,columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in mortar complete with joints to match and set in CM 1:4 complete all as specified & directed by Engineer-in-charge.

Demolition of brick work /stone masonry built in cement mortar incl coping of any description complete all as specified & directed by Engineer-in-charge.

M&L for squared rubble walling, Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) complete all as specified & directed by Engineer-in-charge.

M&L for squared rubble walling, Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) but except stone complete all as specified & directed by Engineer-in-charge.

Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge not exceeding 20mm & dressing face beds and joints as specified to squared rubble walling Jodhpur type brought up to courses complete all as specified & directed by Engineer-in-charge.

JASOL MAA ENTERPRISES

M/S TANUSHREE CONSTRUCTION COMPANY

Leelashah Enterprises

S K TRADER

GEMRARAMCONTRACTOR