REPAIRS TO CERTAIN MISC REPAIRS AND UNKEEP OF JOINERIES , CUPBOARDS AND FLOORING AT MD ACCN AT ARTY CENTRE UNDER GE NASIK ROAD

Amount

Dismantling of stone slabs & tiles of any description or thickness (except ceramic tiles) in floors, aprons etc laid bedded & pointed in any mortar complete all as specified and directed

Demolition of brick work or stone boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillers etc but including ashlar facings, dressed stone work and precast concrete articles

Taking down cement plaster on brick or stone wall etc including raking out joints hacking for keys scrubbing down with water etc. including removing all the debris out side MD land

M&L 75 mm thick PCC 1:4:8,type D-2(using 40mm graded stone aggregate)as in sub base to flooring finished even and fair without using of extra cement all as directed by EIC.

M/L Screed bed or bedding layer of cement mortar 15 mm thick for laying floors finishes in cement mortar 1:6.

M&L for machine cut kota stone slab 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed. Note: screed bed layer, cement motar measured seperately

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with gray cement slurry with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

S & F machine cut cudappa stone slab 16-18 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete Note: screed bed layer measured seperately complete all as specifed and directed

M&L granite (of any type)work (table rubbed and polished) 18 mm thick in steps,jambs,pillars,cooking platforms and like in cement mortar 1:4 incl pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

M&L rough dressed shahabad stone slab 20 to 25 mm thick laid beded and jointed and pointed in CM (1:3) in floors complete all as specifed and directed Note : Cement mortar screed bed layer shall be measured & paid separately

- ditto all as per item no 11 above but except stone

M & L Brick work with fly ash bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 with old size bricks.

M & L Brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 with old size bricks.

M&L for polygonal rubble mesonry, uncoursed well bonded bedded and solidly hearted built in CM 1:6 complete all as specified and directed.

Ditto as Item no-15 but except stones

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, Hammer dressing with maximum depression on face from straight edge held against the dressed surface n exc. 20mm as specified, of random rubble walling,uncoursed or brought upto courses

M&L for keyed pointing of CM 1:4 to random or polygonal rubble;uncoursed or brought upto courses complete all as specified and directed.

M&L for rendering 5 mm thick (1: 3) on fair faces of concrete surfaces incl preparation to new surfaces on ceilings finished even and smooth without using extra cement

M&L for rendering 15 mm thick cement plaster on other than fair faces of brick work or concrete surfaces in CM 1:4 rendering is to be finished even and smooth without using extra cement adding water proofing compound 3% by weight of cement (water proofing compound shall be measured and paid separately)

M&L for rendering 15 mm thick (1: 6) on stone masonry or other than fair faces of brick work surfaces finished even and smooth without using extra cement

M&L for rendering 10 mm thick (1: 6) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement

M&L Preparation of new plastered surfaces and applying three coats of white wash on ceiling surfaces all as directed

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M&L for preparating newly plastered surfaces of walls and applying two coats of OBD over one coat of chalk whitning, prepatory to distempering incl 3mm thick wall care putty complete all as specified and directed.

M&L for preparation of newly plastered surfaces of any description of walls applying three coats of whitewash on undecorated surfaces of walls complete all as specified and directed.

S&F in repairs Vitreous china squatting pan ,'Orissa' pattern, size 580x440 mm white,with integral foot rests (excluding flushing cistern and flush pipe)

S&F of PVC(SWR) 'P' trap of 125/110 mm bore

Dismantling floor hearth or wall tiling including cement mortar bedding (But not backing) removing serviceable tiles to store and rubbish off the premises.

M&L for 10 mm thick rendering in CM 1:4 on brick masonary or concrete rough finished surfaces as backing coat

M&L for coloured glazed ceramic tiles 300 x 200 x 7mm / 300 x 450 x 7-8mm thick in vertical surface, set and jointed in neat cement slurry & pointed with white or coloured cement to match

M&L non-skid coloured ceramic tiles 7 to 8mm thick square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile all as specified and directed by Engr-in-charge

M&L coloured vitrified ceramic tiles any shade 9mm to 10mm thick (square/rectangular) polished, area of each tiles not exc 0.36 Sqm in floors etc set & jointed in neat cement slurry and painted in white or coloured cement to match.

Taking down carefully existing bitumen tarfelt incl. Screed and cleaning of surfaces of roof etc. With wire brush incl. Flashing and junctions of parapets/kerb walls etc. And removing of the rubbish to a distance exc. 500 metres but not exc. 1.5 km and deposting where directed.

Demolition of concrete (unreinforced) of any description and in any position not otherwise specifically provided for.

Providing, cement concrete type B1 1:2:4 (20 mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges.

M&L for 10mm thick plastering (screeding) in cement mortar 1:3 on concrete roof surfaces finished even and smooth without using extra cement and using Water Proofing Compound. Note : Water Proofing Compound shall be paid seperately.

Supply only intergral water proofing compound

M&L for Waterproofing on roof including flashing and junctions of parapet, kerb, wall etc. as under:- (a) Applying bituminous primer on cleaned and dried surface @ 0.7 Kg/Sqm. (b) Laying by thermo fusion (torch applied) 3mm thick APP based polymeric water proofing membrane weighing not less than 3.5 kg/sqm and reinforcement with polyester non woven fabric (not less than 150 gms/sqm). (c) Painting the exposed APP membrane surface with bituminous paint @ 0.15 Kg/Sqm.

S & F in repairs 15 mm bore chromium plated bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule.

S&F in repairs PVC valveless,symphonic action type,flushing cistern ,low level white,with inlet,ball valve,float and handle including brackets of 10 ltrs inclluding flush pipe of polyethelene of low or high dencity or PVC, 32 mm dia all as specified and direcetd.

S & F PVC connections 15mm size with PTMT nuts of length 450mm.

S&F in repairs 40mm size waste fittings, brass chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed.

S&F in repairs 15MM CP stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed complete all as specified and directed

S&F in repairs 15 mm bore Fancy type pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed.

S & F in repairs Vitreous China Ware Wash hand basin white, flat back, size 550 x 400 mm size (flat back or angle back type) including cutting for and pinning ends of brackets or erecting stand.

S & F in repair for chromium plated fancy shower rose with or without swivel joints of 125mm size

Taking up or down 15mm dia tubes galvanized iron and connections and fittings or removal from site as incl cleaning for refixing where directed complete all as specified and directed.

Ditto all as per item No 48 above but 20mm dia

Ditto all as per item No 48 above but 25mm dia

Re-fixing only tubes galvanized iron and connections fixed to walls or laid in floor supplying & fixing new fittings such as socket, bends, elbows nipple, union etc all as specified and directed of size of 15mm dia complete all as specified and directed

All as per item No.51 above but 20mm dia

All as per item No.51 above but 25mm dia

S/F for tubes medium grade, galvanized with iron all fittings fixed to walls, ceiling and laid in floor of sizes of 15mm dia complete all as specified and directed :-

All as per item No.54 above but 20mm dia

All as per item No.54 above but 25mm dia

Taking down 100/75 mm dia PVC/CI sand cast soil, waste and vent pipes, in any length with or without ears etc in any position

S&F of 75mm dia PVC(SWR) pipes single socketed,in any length with rubber ring joints fixed to walls

All as per item No.58 above but 110mm dia

S&F of 75mm dia PVC(SWR) bends of any radius

All as per item No.60 above but 110mm dia

S&F of 75mm dia PVC(SWR) Vent cowl

S&F PVC (SWR) junction (single 'T') equal or unequal, bore 110 mm with access door, complete all as specified and directed.

S&F PVC (SWR) junction (single 'T') equal or unequal, bore 75 mm with access door, complete all as specified and directed.

S&F 50mm dia low density polyethylene pipes(LDPE) of pressure rating 6 Kgf/cm2 fixed complete to walls as directed by Engr-In-Charge

S&F 75mm PVC(SWR) floor trap,plain with grating including jointing with solvent cement

M & L for special treatment to sunken portion with (a) Clean the sunken portion of toilet/Bath/WC/Kitchen throughly to remove laitance, dirt, dust, etc. (b) Form angle fillet of size 40 mm x 40 mm along the junction of wall and floor using polymer modified mortar ("Dr Fixit" Pidicrete URP" or eqvt) (c) Sanitary pipes entering through walls and floor shall be sealed with "Dr Fixit Bathseal Tape" and the gaps to be grouted with non-shrink cementitous grout "Dr Fixit Bathseal Grout" or eqvt. Nahani traps, etc to be fitted securely and the gaps around it to be grouted in the same manner. (d) Apply one coat of a Bitumen-modified polymer coating "Dr Fixit Bathseal Plus" or eqvt on all angle fillets by brush and cover it with 100 mm open woven mesh when it is still wet. Apply second coat of the same coating on the angle fillets and allow it to dry completely. (e) In the remaining area, in dry sustrate condition brush apply first coat of the same coating and further apply second coat when first coat is dry. Extend the coating upto 150 mm above the FFL. Above FFL, another cementitious waterproof coating "Dr Fixit Pidifin 2 K" or eqvt can be further applied right upto 2.1 mm to waterproof the shower area also, it is a bathroom or bath cubicles of a sanitary annex and apply second coat after 6-8 hours and allow to dry completely. (f) After 2 to 3 days, sunken portion must be overlaid with a 50 mm thick concrete screed M 15 type B0 mixed with intergral WPC (Liquid) laid to slope 1:60 towards outer face of wall. Provide 40 mm OD UPVC pipe at the lowest point with 300 mm projection beyond the outer face of the wall. Then fill up the sunken portion with lean concrete 1:5:10 type E2. (g) After completing plumbing work in the toilet/WC/Bath/ Kitchen floor, tiling work (floor and dado) can be carried out using suitable Tile Adhesives and ready-to -make Tile grouts of appd makes such as Dr Fixit, FOSROC SIKA, MC BUCHEMIE, ROFF, etc. Tile to be measured separatly

Taking down chowkat or frames with shutters (without taking off shutters from the frame not exc. 1.5 Sqm each.

Taking down chowkat or frames with shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n exc 4 sqm each.

Taking down shutters of window any description n.exc. 1.00 Sqm each removal from site by contractor at his own expense complete all as specified & directed.

All as per item No.71 above but exc. 1.00 Sqm and n.exc. 2.00 Sqm each

S&F aluminium anodised powder coated (min thickness 50 microns) frame for doors, windows, ventilators, complete all as specifed and directed

Aluminium anodised powder coated door shutters aluminium section weighing not less than 0.55 kg per mtr incl necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges anodised aluminium snap beading, screws etc complete all as specifed and directed

Aluminium anodised powder coated window and ventilator shutter, sliding type without sash bar, alumn section section weighing not less than 0.55 kg per mtr incl necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specifed and directed

S&F Sheet glass ordinary quality 5.5 mm thick exc 0.5 sqm each pane with Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specifed and directed

S&F Sheet glass ordinary quality 4.0 mm thick n. exc 0.5 sqm each pane with Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specifed and directed

S&F floor door stopper of aluminium alloy body & tongue, anodised, with hard drawn steel spring of 140mm size fixed in floor complete all as specified and directed.

S & F Aluminium body door closer hydraulically regulated, designation No. 3 universal type, suitable for door shutters of 851 oto 1000 mm in width and of weight between 61 to 80 Kg.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube S&F in opening as per specification and drawing.

S&F factory made soild panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing.

S&F MS butt hinges 100mm size medium weight complete all as specified and directed

S&F aluminium alloy barrel tower bolt 150 mm long

S&F 150 mm aluminium alloy handels cast/plate type

S&F SS butt hinges 100mm size medium weight complete all as specified and directed

S&F II nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, sup-plied and fixed

S&F IInd class hard wood factory made Glazed and ske- leton shutters 35 mm thick, open rebated and prepared to receive glass, gauze, etc. (divided in to square with sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mi-tred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Sec-tion 8, cla-use 8.20 (a); supplied and fitted to chowkats.

S&F IInd class HW 35mm thick plain framed factory made panelled shutters (two panel) with lock rail, panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS-1003 (Part I) Kiln, Seasoned and chemically pressure treated.

M&L for preparation of new wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

S&F aluminium alloy anodised sliding door bolt 300mm long with hasp & staple (bolt type) and fixing chops of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast alluminium alloy abd fixed

M&L for 18 mm thick PVC sheet prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side with white lamination including necessary locking device, catches suitable for kitchen cabinets and 4 mm thick PVC beading on all edges as in kitchen cabinets etc complete all as specified and directed.

S& F Continuous (piano) hinges 30mm flap size (When open) of MS and fixed with wooden frames with MS screws complete all as specified and directed by EIC

S & F Stainless steel wire cloth, 0.36 mm dia of wire and average width of aperture 1.40 mm and fixed with stainless wire staples.

S & F Stainless steel wire cloth, 0.36 mm dia of wire and average width of aperture 1.40 mm and fixed with stainless wire staples in repairs

Disconnecting existing tanks of exc 500ltrs but n. exc 1000Ltrs, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately)

Dismantling water tanks of size exc 500Ltrs but n. exc 1000Ltr and removing to store

Rotational moulded polyethylene water storage tanks 500ltrs(cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I

All as per item no 97 above but 1000 ltrs tanks

S&F 25mm bore dia Nipple suitable for HDPE water tank. (Minimum weight 25mm- 65gms)

S&F 25mm bore dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed

M&L for rubber moulded machine pressed precast inter locking paver block with gray cement any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-25 grade laid on 30mm thick stone dust cushioning laid dry to the profile complete all as specified and directed

Demolition of cement concrete (unreinforced) of any description and any position not otherwise specially provided for

M&L for cement concrete type C2 1:3:6 (20 mm graded aggregate) 75mm thick in plinth protection complete all as specified and directed including filling of expansion joints with mix.

S&F in repairs tubular rail curtain rod 20mm dia, brass chroium plated complete all as specified and directed by EIC.

S&F for brass chromium plated fancy type brackets for 20mm dia tubular curtain rod including fancy type ends complete all as specified and directed by EIC.

S&F in repair stainless steel sink made of stainless steel 1mm thick with drainage board including plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing contilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx160mm complete all as specifed and directed

NOTE : - AMOUNT OF SCHEDULE OF CREDIT RS 24,116.00 WILL BE DEDUCTED FROM TOTAL AMOUNT OF BOQ.

M/S SAMEER SUBHASH PATANI

M/S K. K. Construction

Srujan Associates

M/S MK Nair

Vinod Enterprises

SVT ENGINEERS AND CONTRACTOR.

MAHIMA CONSTRUCTION

Bidder Name

MAHIMA CONSTRUCTION

Vishal Constructions

M/S SAMEER SUBHASH PATANI

SVT ENGINEERS AND CONTRACTOR.

M/S K. K. Construction

M/S MK Nair

Vinod Enterprises

Srujan Associates