SPL REPAIR REPLACEMENT OF FURNITURE FOR OFFRS JCOS OR MD ACCN AND OTM ACCN AGAINST BER FURNITURE UNDER GE I GOS

Amount

Bed Hard Steel (FD/E6/MAP/08R) All as shown on drg and specification Conduit pipe shall be 38mm sq 1.6mm thick for main frame and 19mm sq 1.6mm thick for inner frame for head and foot board 65mmx25mm 1.6mm thick for long rail. 25mm sq 1.6mm thick for stiffener under 12mm plywood shall be used Prelaminated particle board 18mm exterior grade for head and foot board with PVC edging 1mm thick. Finish : All steel surface shall be black powder coating Rest all as shown on drg.

Chair Dining PVC (FD/E6/MAP/03) All woodwork shall be of 1st class teakwood of special Tectona Grandis conforming to IS-1331:1971 free from knots and cracks shall be used with moisture content permissible as per IS:287:1973. The seat shall be PVC 4mm thick visible like Godrej pattern with 4x10mm thick ribs moulded alongwith seat in single piece screwed with seat frame as shown in drawing. Nylon buffers of appropriate size to bew provided to all the four legs of the chair. All exposed wooden surface shall be smootherned before applying french polish till it attains glossy finish. All joints fixing shall be fixed with bamboo pins and nails shall not be used. Rest all as per drgs or as specified.

Sofa set 5 seater with cushion (FD/E6/MAP/II/02) Overall size of three seater shall be 1730mm wide, 725mm deep and 530mm high up to arm level and one seater shall be 670mm wide and 725mm dee and 530mm high up to arm. All wood to be used shall be 1st class hard teak Wood. Soda set five seater shall consist of one three seater and two single seats. 10xNos of foam cushion to each set each of size 530m,mx560mmx100mm thick of 40 density coverd with white lining cloth and best quality tapestry cloth of rate not less than 450 per mtr shall be provided with nylon zipper at one edge duly covered under the tapestry cloth flap. PVC hard rubber shoes of 25mm dia shall be provided to bottom of each leg with 20mm long screws.All wooden surface shall be polished with high gloss melamine polish in walnut shade after preparation of surface. Rest all specification and dimensions are as per drg.

Table Dining 6 Pers (FD/E6/MAP/II03) (a) The overall size of the table shall be 1500x900x760mm The table top shall be of 18mm thick pre-laminated Particle board exterior grade conforming IS-12823=1990 to Grade I Exterior quality & type-Il (PLMDF-12 Designation) as per IS:14587:1998 (Reaffirmed 2003) (c) All woodwork shall be of 1st class teakwood of specie Tectona Grandis conforming to IS-1331:1971 free from dead knots and moisture content as permissible as per IS-287 (d) 6mm thick TW lipping shall be provided on all the exposed edges of MDF Duly treated with French polish as specified. (f) Powder coated MS angular plates each of 150mmx30mmx5mm thick shall be screwed to the legs at right angles with long rails and short rails. (g) Hard nylon shoes/buffers shall be provided to each leg bottom.

Chair revolving High back Description : Chair Revolving High Back, high density PU in seat & back, titing mechanism, gas lift with arms & chrome base, mModel No ESC/DR/34. Make Royal Koas or equivalent Modle No Versa Neo make Godrej or equivalent fetherlite.

Table Centre 2 tier with Glass Top (FD/E6/MAP/08) Overall size shall be 900mm long, 450mm wide and 400mm high & glass 12 mm over all size be 900 mm long, 450 mm wide and 12 mm hight, Make - Modi gaurd. (a) All wood to be used shall be 1st class hard teak wood. Irrespective of what is shown on drg, the top of table shall be 18mm thick BWR plywood of Grade-A with 1mm thick laminated sheet pasted over the ply with marine grade adhesive and all edges of top shall be covered with 6mm thick teak wood beading.Irrespective of what is shown on drg, one center stiffener of size 20mmx50mm shall also be provided length wise at center in between the side bottom rails 25mm dia hard rubber/PVC rings shall be fixed to the bottom of all legs with 20mm long screws. Rest all specifications and dimensions are as per drg. All wooden surface shall be polished in high gloss melamine finish of walnut shade after preparation of surfaces.

Chair Writing Steel (FD/E6/MAP/12) The overall size of the chair shall not be less than 475mm wide and deep and 580mm high at seat from ground level. The seat and back are to be made up of 1.2cm thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded melamine foam. The back foam is to be designed with contoured lumbar support for extra comfort. The foam is to be moded with density =45+/-2 kg/m3 and Hardness= 20+/-2 at 25% compression. Arm rest shall be one piece. All metel parts shall be dry powder coated in thickness more than 50 microns.

Table Dressing Ladies with Stool (FD/MAP/11) The overall size of the table dressing shall be 1150mm long 380mm wide and 1700mm high and Overall size of the stool shall be 440mm wide. It shall be made up of BWR plywood of grade-A of specified thickness as per drg in lieu of prelaminated particle board.1mm thick laminated sheet shall be pasted on all exterior surface with marine garde adhesive including 6mm thick teak wood beading shall be provided alround the edges of shutters and drawers. Drawers shall be provided with 2x Nos of inch long stainless steel telescopic channels.Drawer and shutter shall be provided with 90mm long recessed metal handles and shutter to be provieded with magnetic catches. Looking mirror shall be 5mm thick electro copper plated fixed over 6mm thick plywood back. 4x Nos heavy duty double wheel castors shall be provided at bass ply. The seat of the stool shall be 75mm thick, 40 density foam cushion covered with best quality tapestry cloth of rate not less than 450 per mtr rest all specification and dimesions are as per drg

Charpoy Folding IP with hard top (FD- 388(R)) All as shown on drawing. Overall size shall be of 1980x900x550mm.The frame work shall be 25mm dia 16 guage MS conduit pipe.04 nos stiffner shall be provided between long rail 25mm dia 16 guage .Top shall be of 8mm thick BWR plywood conforming to IS-303. Rest all as shown on drawing. All joints/weldings/fixing shall be done in accordance with standard workmanship. All frame work shall be painted with spray paint synthetic enameled over a coat of primer all as directed by Engg-in -charge.

Receptical PVC (FD/E6/MAP/13) All as shown on drawing. Overall size Receptical shall be of capacity 20 ltr . The body of receptical PVC shall be made up of thick polymet plastic of thickness not less than 2.5mm provided with swivel lid and iron handles on both sides as shown in drg. Make Cello, TUPPERWARE or AMKO equivalent as shown in drg.

Almirah Large Steel 1/2Hx1/2S (FD/E6/MAP/18) (a) Overall size of Almirah large 1/2 Hx1/2 Sh steel shall bel 900mmx 910mmx 475mm. (b) Almirah's body, shutter, drawer, locker, vertical partitions and shelves shall be made out of 20 Guage MS plain black sheet all as shown in drg. (c) Back shall be of 22 Guage plain black sheet. (d) Welding process shall be of MIG (Metal Inert Gas) type using Carbon dioxide and Argon blend. (e) All MS members shall be pre-treated with epoxy polyester powder coating (Black) 70 microns by 7 tank process and Oven Dried internally & externally with the following specifications. (i) Dry Film thickness more than 45 microns (ii) Salt Spray test to with stand more than 1000Hours. (iii) Adhesion as per DIN 53152 standards. (iv) Pencil scratch hardness more than 2H (f) Rest all as per drg.

Table Dressing Gents With Glass(FD/E6/MAP/16) Overall size shall be 1200mm high, 600mm wide and 100mm high. All wood to be used shall be 1st calss hard teak wood. It shall be made up of BWR plywood of grade-A of specified thikness as per drg in lieu of prelaminated particle board. 1mm thick laminated sheet be pasted on all exterior surface with marine grade adhesive including 6mm thik teak wood beading shall be provided alround the edges of shutters and drawers. Looking mirror shall be 5mm thick fixed inside the teak wood frame made out of 38mmx25mm section. 03x glass shelves of 5mm thickness shall be fixed inside the box with glass holders as shown in drg. Rest all specification and dimensions are as per drg. Preparation of surfaces shall be polish in high gloss melamine polish.

Trestle Store room Steel (FD- 1043) This drawing superseded drawing No - FD-86(M) SHEET 1/1 FOR TRESTLE STORE ROOM ( STEEL) ONLY. All as shown on drawing . Overall size shall be 2440mm long, 600mm wide and 300mm high. Two long angle iron 40mmx40mmx600 of mild steel 1980mm long shall be provided 520mm apart at bottom connected with 50mmx300 flat iron bracing, four in numbers, and equally spaced with 50mmx50mmx6mm T-iron. Two flat iron mild steel bracing of 50mmx3mm shall be provided as a cross bracing joining vertical T-iron provided at four equally spaced members of T-iron. Two long mild steel angle iron 40mmx40mmx6mm of 2440mm long shall be provided at top. Two short mild steel angle iron 40mmx40mmx600 of 600mm Tength shall be proveded at both the ends of trestle. Two numbers50mmx50mmx6mm T-iron 600mm long be provided equally spaced joining two long angle iron. Four cross bracings at top shall be provided with 50mmx3mm mild steel flat iron bracing. Four mild steel flat iron stuts shall be provided to each side of the trestle. All jointing, welding and fixing shall be done in accordancewith standard workmanship. all Steel and iron work surfaces shall be painted with two coats of enamel paint over a coat of primer with spray after prepration of steel surfaces on esposed to viev when placed in position.

Almirah Med steel (FD- 1032) (a) Overall size of Almirah shall be 1270mmx760mmx440mm having three shelves and four compartments. b) Top, doors, shelves and base and legs shall be made up of MS Sheet of imm thick(nominal). c) Handle shall be 100mm long Chromium plated. d) Four lever Lock shall be provided of Grade Il quality conforming to IS 729/1979 alongwith duplicate keys. (e) All MS members shall be pre-treated with epoxy polyester powder coating (Black) 70 microns by 7 tank process and Oven Dried internally & externally with the following specifications. (i) Dry Film thickness more than 45 microns. (ii) Salt Spray test to with stand more than 1000Hours. (iii) Adhesion as per DIN 53152 standards. (iv) Pencil scratch hardness more than 2H. (d) Welding process shall be of MIG(Metal Inert Gas) type using Carbon dioxide and Argon blend. (e) All MS surface shall be spray painted with two coats of synthetic enameled colour to be approved by GE over a coat of red oxide primer

Table 900x600x760mm with drawer steel (FD- 1008) All as shown on drg. Over all size shall be 900 mm x 600 mm x 760 mm steel frame shall be of 800 mm x 500 mm x 742 mm. Four legs shall be of 25 mm squre mild steel tube of wall thickness 1.6 mm top of legsshall be joined together width 25 mm squre mild steel tube of wall thickness 1.6 mm top rail on long and short sides. Two short stiffner joining legs in short sides at 100 mm front bottom shall be provided in the middle of short stiffener joining short stiffener with 25 mm squre mild steel tube of wall thickness 1.6 mm at 100 mmmfront bottom of legs. A drawerr on left side of table near top stiffner shall be provided of size 350 mm x 130 mm and 500 mm deep with lockinng arrangement and recessend handle. Mild steel sheet used for drawer shall be of 1 mm thick. Top of table shall be of 18 mm tick prelaminated particle board with teak weneer shade and PVC edging all round the top of table, irrespective of what is shown and specified on drg. PVC/Hard rubber toes shall be provided two the bottm of leg. All steel surface with two coats of enameld paints over a coat of primer with a spray machine after preparation of steel surface.

Side board (FD-26(M)) (a) The overall size of the side board shall be 1025x450x750mm. (b) Top, sides, shutters and bottom shall be of 18mm thick pre-laminated particle Board, Ext grade l/Type Il conforming to IS: 12823 along with 4mm thick teakwood edging to be provided (c) Four Drawers shall be provided at equal spaces. (d) Powder quoted MS handle 02 Nos of size 100mm long to be provided to two doors each. (e) Two catch spring shall be provided to the shutters. (f) 75mm high skirting shall be provided of 19mm thick teakwood. (g) All exposed wooden surfaces shall be French polished to attain glossy finish. (h) Rest all as per drg & all as specified.

Chair Varandha PVC (FD/E6/MAP/11) a) 19 mm MS tube of 16G thick shall be used for frame work. (b) Welding process shall be of MIG (Metal Inert Gas) type using Carbon dioxide and Argon Blend. Joints of welded portion shall be finished smooth. (c) Finish: All MS members shall be Pre-treated with epoxy polyester power coating (Black) 70 microns by 7 tank process and Oven Dried with the following specifications: (i) Dry film thickness more than 45 microns. (ii) Salt Spray test to with stand more than 1000 hours (iii) Adhesion as per DIN 53152 standards. (iv) Pencil scratch hardness more than 2H. (d) 4mm thick seat & back shall be made out of PVC moulded alongwith 4x10mm ribs provided at all around the outer edge & around the grooves of size. (e) Hard PVC inner shoes shall be provided for the legs duly affixed with adhesive. (f) Rest all as per drg or as specified

Chair Easy (FD-229) Dimension : Overall size shall be 510mm long, 575mm wide and 720mm high. Description : a) All wood to be used shall be 1st class hard teak wood b) PVC hard rubber ring of dia 25mm shall be provided to bottam of each leg with 20mm long screws. c) Caning shall be done in true godrej pattern with virgin plastic cane of 2mm wide, 0.6mm thick half round gola type weighting not less than 6 gms in ten running meters with border woven with 4mm thick cane. Rest all specification and dimensions are as per drg. FINISH: The chair shall be polished in high glass melamine polish in walnut shade after preparation of surface.

Chair writing (FD-280) All woodwork shall be of 1st class teakwood of specie Tectona Grandis conforming to IS-1331:1971 free from dead knots and moisture content as permissinle as per IS-287. Canning of the chairs shall be of Godrej pattern with 2mm and 3.5mm approved qulity of plastic cane and holes to be covered by 3.5mm wide cane. The canning used for seat has high tensile strength as specified IS:5378 Part II/1990, Cane breaking strength=3000kg/mm2(min) % Elongation at break =25%. TW triangular brackets of size 60x60x25mm thick both ends chamfered shall be screwed on the legs/side rails joint below seat for both rear and front legs ie 4 bracket per chair. PVC rings to be screwed of appropriate size to be provided to all the four legs of the chair.All exposed surfaces shall be french polished.

Table office Clk steel, Description: Table office Clk steel size 1200 x 750 x 750 mm, modle No ESC/OT/004, Make Royal Koas or equivalent Modle No T - 101 make Godrej or equivalent fetherlite.

Teapoy varandha (FD/E6/MAP/17) a) The overall size of the teapoy verandah shall be 750mmx450mmmx540mm. b) Table Top shall be 18mm thick pre-laminated particle board, exterior Grade pre-laminated one side with teak finish and matching white on other, conformjng to IS: 12823 and ISI marked. Edges shall be provided with 4mm thick teakwood beading, c) The main frame work for Rails. legs, stiffeners & base shall be of 18mmx18mmx18guage CRCA box section. d)The void of base tray frame shall be filled by weld 5mm MS bars, 10 Nos in length —wise and 12 in widthwise. e)All CRCA/MS members shall be pre•treated with e poxy polyster powder coating (Black) 70 microns by 7 tank process and Oven Dried internally & externally With the following specifications. (O) Dry Film thickness more than 45 microns. (n) Salt Spray test to with stand more than 1000Hours. (iii) Adhesion as per DIN 53152 standards, (iv) Pencil scratch hardness moro than 2H. (f) Rest all as per drg or as specified

Rack adjustable 6 tier (FD-106(M)) Overall size shall be 915mm long deep 1905mm high. Four angles of 30mmx30mmx3mm shall be provided at four corners as vertical . Bottom and intermediate shelves shall be provided of 1mm mild steel sheet. The rack shall be enclosed with mild sheet 1mm thick on top. Sides and back fixed to angle iron with spot welding. Four angle corners 150mmx150x1mm of mild steel sheet shall be provided to front, top and bottom corners . All steel and iron surface shall be painted with spray paint of two coats of enamel paint over a coat of primer after preparation of surface as directed by GE to obtain smooth finish.

Stool revolging adjustable steel (FD-103(M)) All as shown on drawing . Overall size shall be 455mm dia and 600mm high .Four legs of 25mm dia mild steel sheet pipe legs made to shape of wall thickness 1.6mm irrespective of what is shown on drawing .12mm dia mild steel bar ring shall be provided at 150mm from bottom joining four legs as shown on drawing. Two cast iron discs shall be provided at top of legs and at 100mm from to of legs as shown on drawing and fixed to legs with 6mm dia bolt. 25mm dia threaded steel bolt 255mm long fixed with 6mm thick steel plate 100mm dia at top of 25mm dia threaded bolt shall be provided as shown on drawing. The padded seat shall be fixed on 6mm thick, 100mm dia steel plate with screws for which four number holes are provided in steel plate. padded seat shall be 380mm

Table Peg (FD- 384) a) All wood work shall be first class hard wood season teak. (b) Irrespective of whatever is showin in the drg top shall be 18/19mm thick prelaminated particle board exterior grade OSD lamination of teak finish shade and other white balancing lamination as specified here-in-before ISI marked.c) All exposed surface shall be French polished in golden colour. (d) 4mm teak wood edging for table top shall be provided as shown on drg. (e) Hard PCV toe shall be provided on each legs. (f) All joints fixing shall be done in accordance width the standard work manship and specification. (g) Rest all as per drg or directed by Engineer-in-Charge.

Board notice 3' x 2' (FD- 366) All as shown on drawing . Overall size shall be 900mm long and 600mm high sides, top and bottom shall be of first class hard wood teak 9mP) frame 75mmx75mm in section made to shape as shown on drawing. Green baize cloth of best quality shall be fixed on 12mm thick soft board fixed on 6mm thick commercial plywood irrespective of what is shown on drawing. Front shall have two shutters ope-able hinged on sides. Front frame of shutters shall have styles and ralls of 45mm wide and 25mm thick teakwood. Two horizontal stiffeners 19mmx25mm in section shall be provided at equal spacing as shown on drawing.One vertical stiffener 19mmx25mm shall be provided cerntrally. Glass for galzing in front shutters shall be 3mm thick fixed on shutters with 10mmx10mm teak wood beads 75mm long hinges, two to each shutter shall be provided as shown on drawing, 50mm long hasp and staple shall be provided in the center 40mmx25mmx3mm thick key plates shall be provided all as shown on drawing. All wood surfaces exposed to view when placed in position shall be french polished with high gloss finish, steel and iron surfaces shall be given two coatsof enamel paint over a coat of primer.

Locker Bed side steel (FD-257) Overall size shall be 760mm long, 600mm wide and 1100mm high. All steel shall be of 1mm thick in front, back , sides, top and bottom. Legs shall be of U shape channel 100 high and 60mm wide ends plugged with 1mm thick mild steel sheet. The legs shall be welded to bottom of almirah. Half of almirah shall have shelves and other half shall have hanging space. A vertical partition shall be provided dividing the width of almirah in to two halves. Hahging portation shall habe 20mm dia chromium plated steel conduct pipe 1.6mm wall thickness with sockets at 55mm from front of shutter of almirah or 80mm top of almirah as directed by Engineer-in-charge. Two shelves, making three equal compartment shall be provided in the other hall of almirah. Two black steel studs fixed in side of shutter shall be made to shape with 1mm thick sheet and 80mm wide, height being that of shutter shall be provided a directed by Engineer-0in-charge. One number safety type, chromium plated brass haps and staple at 75mmx40mmx3mm shall be provided to front shutter. chromium plated handle 100mm long shall be provided to each shutter as shown on drg. Two 50mm long tower bolt shall be provided to one shutter in the inner side as directed by Engineer-in-charge. Front shutters of almirah shall be side hung with 75mm long bult hinges. All steel surface coats to enamal paint over a coat of primer after preparation of surfaces painting shall be done with spray machine.

Table dining 8 Pers (FD/E6/MAP/II/03) The overall size of the table shall be 2100x900x760mm. The table top shall be of 18mm thick pre-laminated particle board exterior grade confroming,exterior qulity as per IS:14587:1998. All woodwork shall be of 1st class teakwood of specie tectona grandies conforming to IS-1331:1971 free from dead knots and moisture content as permissible as per IS-287. 6mm thick TW lipping shall be provided on all the exposed of MDF Duly treated with french polish as specified. Powder coated MS angular plates each of 150mmx30mmx5mm thick shall be screwed to the legs as right angles with long rails and short rails. Hard nylon shoes/buffers shall be provided to each leg bottom.

Table computer, Description: Table computer ergonomically with slide in ke board shelf and a storage shelf for voltage stabilizer and accessories of size 48" x 24" x 30" model No ESC/CT/45, Make Royal Koas or equivalent Modle No Buddy with KBPT, PC - 3009 Make Godrej or equivalent fertherlite.

ABHIMANYU MAHARANA

DEBASHIS AGENCY

Capital Construction Company

PRADIPTA KUMAR PANI