SPECIAL REPAIRS TO BLDG NO T-57 OF HQ COSA AT NAYA RAIPUR

Amount

Demolition of cement concrete in ground floor and paving n.exc 15cm thick (below or above ground level) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off premises complete all as specified.

M&L for light shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and incl 15mm thick screed bed in cement mortar (1:4) for laying floor finished complete all as specified and directed.

M&L non skid coloured ceramic tiles 7 to 8 mm thick(square/rectangular) area of each tiles exceeding 0.06 sqm but n.exc 0.11sqm in floor etc,over 15 mm thick screed bed in CM(1:6),set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces complete all as specified and directed.

M&L for glazed ceramic coloured cut tiles 350x250x7mm/450x350x7mm thick on vertical surfaces such as skirting dados set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM (1:4). Complete all as specified & directed.

M&L for cement concrete 1:3:6 type C2, 75mm thick (40 mm graded stone agg) as in plinth protection complete all as specified and directed.

M&L 25 mm thick PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in floors finished even and fair surface complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp,insulation etc) or insulation board/slabs/blankets any thickness including cover fillets all as specified.

Supply & fixing 'E' board 605 x 605 x 4 mm thick white prelaminated set & embosed, reinforced, designer ceiling board tiles of approved texture fixed at all height laid on hot dipped galvanised iron imposed grid with 24 mm wide T-section exposed flanges which shall be powder coated, white,.the frame work shall comprises of main runner made from 0.33 mm thick galvanised steel sheet and of size 24 x 32 x 300 mm and spaced at 1200 mm center to center fixed to be structural soffits by approved hangers at 1200 mm rawl center, hangers of GI wire 4 mm dia to be fixed by approved rawl plug, level and fasteners and screws etc., the last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall, flush fitting of 120 mm long cross tee (with double stiching) to be interlocked between main runners at 600 mm center to center, size 1200 x 600 mm modules, cross tee longer than 600 mm to be supported independently on 600 x 600 mm moduler to be formed by fitting 600 mm long cross tee centrally between the 1200 mm cross tee. Tee, perimeter wall angle shall be of 0.45 mm thick GS sheet of size 19 x 19 mm and 300 mm long of white colour all as per manufacturer's instructions complete all as specified and directed.

M&L for 12mm thick Pre-laminated particle board, interior grade Pre-laminated both sides with decorative choice lamination & other side balancing white lamination fixed with screw to timber/MS frame work complete all as specified and directed.

M & L brick work with sub class B bricks straight or curved on planexc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L rendering 15mm th plaster in CM 1:6 on fair faces of brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for two coat of oil bound emulsion distemper incl preparation of new plastered surface of wall over a coat of primer complete all as specified.

M&L for rendering 15 mm thick plaster in CM (1:4) on brick or concrete surface in two layer of 10mm and 5mm thick each. Second coat of 5mm thick with water proofing compound as per manufacturer instruction finished even and smooth all as directed (WPC shall be measured and paid separately).

Demolition of brick work with built in cement mortar, complete all as specified and directed.

Supply only integral water proofing compound.

M&L preparing surface plastered or unplastered on wall with two coats of Cement base paint over a coat of alkali resistant primer paint with complete all as specified and directed.

M & L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

Demolition of reinforced concrete in ground floors and paving n.exc 15cm thick (below or above ground level complete all as specified and directed)

M&L reinforced cement concrete (nominal mix) 1:2:4 type B1 using 20 mm graded stone aggregate as in Columns, pillars, piers, posts and struts complete all as specified and directed

Formwork to Square, rectangular or polygonal rough surface of concrete of sides of pillars, posts, struts, piers, columns and stanchions

M&L reinforced cement concrete(Nominal mix) 1:2:4 type B1 using 20mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Ditto, but 5mmdia and over upto and including 10mm dia in stirrups, spacer and binders complete all as specified and directed.

S&F Powder coated anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). Hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed by Eng-in-charge.

S&F Powder coated anodised aluminium frame for door section/ window section/ ventilator section for side hung type shutter /sliding type shutter/fixed type shutter in two or more tracks, including automatic locking handle , rollers and roller plate & fitting arrangement complete all as all as specified and directed by Engineer-in-charge.(Glass pane , hydraulic door closer , plush plate, floor hinges shall be measured and paid separately.

S&F for Steel door including projecting type hinges, steel handle, complete, with glazing bars, dovetailed or welded complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not other wise provided complete all as specified and as directed.

M&L Rolled MS sections as in framing for Stairs (framed) including stringers, treades, landing,balusters, hand rails etc. Including cleats, brackets, etc complete ® of grade Fe 410-W (Gde E-250), etc complete all as specified and directed.

M&L Rolled MS sections as in framing for cladding, glazing and the like including door frames/chowkats, roof trusses Joist, channel, angle, or tee sections fixed with angle cleats and connecting plates of grade Fe 410-W (Gde E-250), etc complete all as specified and directed.

S&F for wind ties for roof including securingbolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165.

Taking down chowkats or frames exceeding 1.5 Sqm and not exceeding 4 Sqm with shutter (Without taking off shutters from the frame) & removing from site complete all as specified and directed.

Taking down chowkats or frames not exceeding 1.5 Sqm and with shutter (Without taking off shutters from the frame) & removing from site complete all as specified and directed.

S&F galvanised steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in repairs complete all as directed at site.

S& F for sheet glass 4mm thick, ordinary quality and glazing fixed with aluminium section in squares not exceeding 0.5Sqm in each pane complete.

S & F Door closer hydraulically regulated of aluminium (Extruded section) body designation No.2, universe type, suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 kg and fixed complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S &F Factroy made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with het moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuch inside with solvent cement for stiles and plan colour PVC sheets for top rail, lock rail & bottom rail on either side & as fap insert for top rial & bottom rail, Penelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement supplying & fixing in the frame at site as per specification & drawing.

S&F in repair 20 mm dia decorative type curtain rod with rings and brackets complete and all as specified and directed

Dismantling plain or corrugated steel sheeting, any gauze, thickness, including Nainital or similar pattern roof coverings etc complete all as specified and directed..

S & F for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S & F for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F plain black mild steel sheeting 0.80mm thick in ridge, valley gutter & fascia,drip and straight flashing as directed by Eng-in-charge.

Taking down cement plaster on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L for Rendering 10 mm thick on brick work or concrete surfaces in cement mortar (1:4) finished even and smooth without using extra cement complete all as specified & directed.

M&L 3 coats of white wash of newly plastred surfaces of walls complete and all as specified and directed

M&L of two coat of synthetic enamel paint over one coat of red oxide on new steel surfaces of any description over 10cm in width or girth incl preparation of surfaces complete all as specified and directed.

M&L one coat of synthetic enamel paint on old steel surfaces of any description not otherwise described over 10cm width or girth including preparation of old surfaces complete and all as specified and directed

M&L for preparation of old decorated plastered or unplastered surfaces of walls and applying one coat of cement based paint all complete as specified and as directed.

S & F in repairs Brass CP mixer(40 mm bore dia) for mixing hot & cold water screwed down for iron pipe and fixed complete and all as specified and directed.

S&F in repairs bib taps cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fancy type chromium plated of 15 mm bore dia of pipe complete all as specified and directed.

S&F in repairs Grating doom 125 mm dia with waste hole of PTMT Minimum weight 40 gms complete all as specified and directed.

S&F in repairsStop valves cast copper alloy, screwed down, high pressure with crutch or butterfly handle chromium plated fancy type screwed both ends for iron pipe or for unions for 15 mm bore dia of pipe complete all as specified and directed.

S & F in repairs for Toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws complete all as specified and directed.

S&F in repairs for vitreous china wash basin, white flat back size 550x400mm including waste, chain & plug andporeclain stopper and bracket etc. Complete including cutting for and pinning in ends of brackets or errecting bracket and 32mm dia waste fitting brass chromium plated for sink etc;with long screwed shanks and fly nuts,flange end bedded in red lead cement including 32mm dia waiste pipe fitted complete all as specified and directed.

S&F in repairs PVC connection pipe 45 cm long with PTMT fixed to WHB, flushing cistern an complete all as directed at site.

S&F in repairs 75 mm dia outlet PVC (SWR) floor trap plain with steel grating including jointing with solvent cement complete all as specified and directed.

S&F in repairs Vitreous China wash down water closet pan(pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe "P" or "S" trap (excluding flushing cistern and flush pipe) but including connection to trap, and to flushing pipe, anti-syphonage pipe etc. all as specified and as directed.

S&F in repairs for PVC flushing cistern, 10 ltrs capacity with inlet, ball valve, float and handle, including bracket and 38mm dia flush pipe of polyethylene for low level cistern complete all as specified and as directed.

S&F in repairs soap dish any type fixed to plugs with chromium plated brass screws complete all as specified and directed

S & F in repairs for Shower arm 15 mm size, 195mm long withbend of 45degree with flange of PTMT any colour.(Minimum weight 40gms all as specified and directed.

M&L in repairs brass chromium plated tubular towel rail 20mm dia D type 600 mm long between flanges fixed Complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc

M & L for Point wiring using approved colour coding as per IS, with stranded copper conductor 1.5 sqmm (nominal area), single core, flame retardant low smoke(FRLS), PVC insulated and unsheathed cable 1100 volts grade, ISI 694 marked TEC and FIA approved in and including PVC concealed conduit and its fittings ISI marked, with mild steel sunken boxes suitable for modular/normal switch/sockets etc with earth dolly duly painted with two coats of anti corrosive paint over a coat of red oxide primer internally, incl covered with suitable module cover plate with frame including flame retardant low smoke (FRLS) PVC insulated unsheathed stranded copper conductor 1.5 sqmm (nominal are) single core cable as earth continuity conductor to common earth and connected to earth dolly complete all as specified for One light/ Bell point controlled by one switch.

Ditto all as per above items No 67 but One Fan/ Exhaust fan point controlled by one switch all light point.

Ditto all as per above items No 67 but One socket out let 3 pin 5 Amp on independent board

Ditto all as per above items No 67 but One socket out let 3 pin 5 Amp on same board

All as per item No 67 above but using 4.0 Sqmm cable for one 15 A socket outlet point controlled by one switch on independent board with and including 2.5 Sq mm PVC insulated, unsheathed copper conductor cable as earth continuity conductor.

S & F modular switch 1 way 6A 1 module complete all as specified and directed.

S & F modular socket 6A 2/3 Pin combined 2 module complete all as specified and directed.

S & F modular socket outlet 1 way 6/16 Amps 2/3 pins combined 2 module complete all as specified and directed.

S & F modular switch 1 way 16A 1 module complete all as specified and directed.

S & F for modular Bell Push switch 6Amps, 1 module complete all as specified and directed.

S & F Buzzers and Bell, Ding Dong AC 230 Volts Single pole complete all as specified and directed.

S & F for modular fan regulator 120W, 2 module ISI marked, complete all as specified and directed.

S & F modular white cover plate and frame 2 module complete all as specified and directed.

S & F modular white cover plate and frame 3 module complete all as specified and directed.

S & F modular white cover plate and frame 4 module complete all as specified and directed.

S & F modular white cover plate and frame 6 module complete all as specified and directed.

S & F modular white cover plate and frame 8 module complete all as specified and directed.

S & F for ceiling rose 3 phase/PVC/polycarbonated isolated body complete all as specified and directed.

S & F Modular flush box 2 module complete all as specified and directed.

S & F Modular flush box 3 module complete all as specified and directed.

S & F Modular flush box 4 module complete all as specified and directed.

S & F Modular flush box 6 module complete all as specified and directed.

S & F Modular flush box 8 module complete all as specified and directed.

S & F for power unit mini modular MCB box with mini MCB 20 Amps SP with ISI plug top with box for connecting AC's upto 2 ton complete all as specified and directed.

Supply and fixing LED lights fitting 1x 18W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fix building security light of 35/36 watt IP 65 watt,LED die casting aluminium with LED street optic lenses ,efficacy of skyline plus is upto 120lm/w, with pea nut lenses LED type with bracket arrangement all as per required and directed by Engg in Charge.

Taking down ceiling fans/ exhaust fan, sealing cable end, dismantling blades and removing fan and blades deposite to store complete all as specified and directed.

Supply and fixing ceiling fans complete with biades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

S & F for MCB DB's 16 Way (Horizontal each 4 way) TPN, 415 volts for mounting MCBs/RCBO's ELCB's etc. as per IS specification of factory made fabricated out of CRCA sheet 1.2 mm thick powder coated fitted with DIN Channel neutral link and 200 Amps rated bus bar.The DB's shall double door type . Inner door fixed on spring loaded hinges with locking arrangement & outer door openable hinged with locking arrangement having IP-43 protection complete all as specified and directed.

Supply and fixing 415V 10KA 'C' curve MCB of 63 Amps TPN and current carrying capacity in the DB complete with connection testing and commissioning.

S & F for MCB SPN 40 Amps 240 Volts C Curve 10 KA complete all as specified and directed.

S & F for MCB SP 40 Amps 240 Volts C Curve 10 KA complete all as specified and directed.

S & F for MCB SP 6-32 Amps 240 Volts C Curve 10 KA complete all as specified and directed.

M & L for Sub main wiring with approved colour coding as per IS with two runs of single core PVC insulated cable FRLS with Multi Strand copper conductor of size 6 Sq. mm and drawing into PVC conduit including one run of PVC insulated 6 sqmm stranded copper conductor earth wire complete all as directed. Note : Three run of 6 Sqmm wire and one run of PVC conduit shall be measured as one unit.

M & L for Earthing complete with galvanised steel earth plate electrode of size 60cm X 60cm X 6mm buried directly in ground (earth pit not less than 2.25 metres deep below the normal ground level) with top edge of the plate not less than 1.5m below normal GL connected to GI earth wire 4 mm dia by means of GI bolts, nuts, check nuts and washers and earth strip protected by 25 mm dia GI pipe medium grade and connected to main distribution board/earthing test point all as shown on electrical plate No.3 of SSR Part I and all as specified including testing on completion.Notes: The unit rate shall also include for excavation, earth work in hard/dense soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix, type B1 cover reinforced with 8mm dia TMT bars @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh, protection pipe for earth lead upto 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II and also refer Plate No-03. Earth strip and protection pipe beyond 7.5m shall be measured and paid separately. Note :- Earthing will be redone if desied erath result not found during testing of the same at site.

M & L for taking down window type AC of any capacity by disconnecting the existing cable connection, kept in store and re-fiixing by connecting with AC metal box/Socket after wall panelling of the room including testing of AC at the satisfactory level of Engr-in-Charge. Note : AC metal box/Socket will be measured and paid separately

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm Sweep complete all as specified.

Supply, laying and connecting XLPE insulated armoured heavy duty electric cable 16 sqmm 4 core with aluminum conductor 1100 volts grade cross sectional area laid in ducts/wall/cable tray/trenches with suitable size of cable glands, crimping type cable lugs, connecting to existing MCCBs in panels all as specified.

Total contract sum shall be calculated after deduction of schedule of credit amount of Rs. 34893.00

ASHOKA ASSOCIATES

m/s ramanuj singh and sons

M/S INDIA ENTERPRISES

FIRST SOLAR