PROVIDING SOUND SYSTEM IN MAIN MANDIR BHAGWAN VALMIKI JI AND PARIKARMA AT BHAGWAN VALMIKI JI TIRATH STHAL AT RAM TIRATH, DISTT AMRITSAR

SITC of 2-way full range Loudspeaker,Having Point Source Cabinet, should have 1 x 12” Low Frequency Driver, 1 x 1.4” or Higher Horn loaded Compression Driver, HF Horn or cabinate should Be Rotatble for getting desired coverage pattern ,400 watt or lower Continous RMS Power, 1400W or Higher Peak Power, 8 ohms impedence , Frequency Response(-3db) from 60Hz or lower to 18khz or higher, Average Sensitivity - 97dB or higher, Max SPL Peak 128 db or higher, Horizontal Dispersion 90° or higher,Vertical Dispersion 55° or Higher,The Speaker cabinet Should be made of Touring grade Birch Plywood and Have 12 or Higher x Suspension Mounting points for both horizontal and vertical flying Cabinet.Cabinet Should be Multi purpose cabinet design for FOH or monitor use. complete in all respects as approved and desired by the Engineer in-charge at site.

SITC of Customised Brackets made up of power coated Mild steel for mountind of speakers on wall horizontaly or vertically.complete in all respects as approved and desired by the Engineer in-charge at site..complete in all respects as approved and desired by the Engineer in-charge at site.

SITC of 2-way full range Loudspeaker,Having Point Source Cabinet, 1 x 8” Low Frequency Driver, 1 x 1.4” or Higher Horn loaded Compression Driver,Horn or cabinate should Be Rotatble for getting desired coverage pattern ,350watt or lowerContinous RMS Power, 400W or Higher Peak Power, 8 ohms impedence, Frequency Response(-3db) from 75Hz or lower to 17khz or higher, Average Sensitivity - 94dB or higher, Max SPL Peak 121 db or higher, Horizontal Dispersion 90° or higher,Vertical Dispersion 55° or Higher,The Speaker cabinet Should be made of Touring grade Birch Plywood,12 x Suspension Mounting points for both horizontal and vertical flying Cabinet.Cabinet Should be Multi purpose cabinet design for FOH or monitor use. complete in all respects as approved and desired by the Engineer in-charge at site.

SITC of Customised Brackets made up of power coated Mild steel for mountind of speakers on wall horizontaly or vertically. complete in all respects as approved and desired by the Engineer in-charge at site.

SITC of 2-way full range Looudspeaker,Having Point Source Cabinet, 1 x 8” Low Frequency Driver, 1 x 1” or Higher Compression Driver,200watt or lower Continous RMS Power,240W or Higher Peak Power, 8 ohms impedence or 70/100 volt line operation , Frequency Response(-10db) from 70Hz or lower to 20khz or higher , Average Sensitivity - 93dB or higher, Max SPL Peak 121 db or higher, Horizontal Dispersion 90° or higher,Vertical Dispersion 60° or Higher,includes an integrated transformer with multiple power tap settings,Speaker Should Have 80 watt or Higher power Taping at 100V operation,The Speaker cabinet Should be of IP 54 or higher Rated ,Powder-coated aluminum grille,UV-resistant ,Corrosion-resistant Components.complete in all respects as approved and desired by the Engineer in-charge at site.

SITC of Professional Grade Four channel or Higher, Power amplifier Having Power output 600W or higher @ 8 ohms at Each Channel, 600W or higher @ 4 ohms at Each Channel in all channel drive mode, Frequency Responce - 20Hz - 20kHz, , Input Impedence - 20k ohm or higher, Crosstalk - >65dB or Higher, S/ N ratio - > 101dB or Higher, , THD - < 0.1% or Lower.complete in all respects as approved and desired by the Engineer in-charge at site.

SITC of High performance Outdoor full range loudspeaker with 1 × 4.5”or higher Driver,Power Handling : 160 W or lower RMS ,200W or Higher peak,8 ohm and 100V/70V operation possible, LMT in-built,Frequency Response (-10dB) from 80Hz or Lower to 15KHz or higher,Average Sensitivity 85dB or higher,Calculated Max SPL 105dB Peak or Higher,Speaker Should Have 30 watt or higher Taping at 100V/70V operaion,Speaker Should Have Weatherised IP55 or higher Standard Cabinet. Speaker Should be floor mounted.complete in all respects as approved and desired by the Engineer in-charge at site.

SITC of Digital signal processor Having 16 inputs or higher(atleast 8 Analog inputs + 8 Digital Inputs) , 16 outputs or Higher (Atleast 8 Analog outputs + 8 Digital outputs), Should Have Matrix DSP routing for all inputs and outputs,Should have Dante connectivity for Inputs and Outputs ,Should Have 32-bit or higher floating point processor,24bit/48KHz or Higher sampling rate,In-built USB sound card for USB recording and soft video Conferencing Codec,Acoustic Echo Cancellation (AEC) 8×8 or higher.Low pass & high pass filters – and limiter on output channels,8-way GPIO (General purpose input output) configured as inputs or outputs, allowing for flexible control of digital signals,Ethernet, RS232/485 control interface for third-party control, Frequency Response 20Hz - 20kHz, ±0.3dB,Input Dynamic Range 110dB or higher,Output Dynamic Range 112dB or higher,,Input Impedance 5kΩ or higher ,Output Impedance 100Ω or higher. complete in all respects as approved and desired by the Engineer in-charge at site.

SITC of Power Amplifier Having Max power output 480W or higher, 2 or higher mic or line inputs, 70V/100V line output,Flexible output options: 4-16 ohm or 70V/100V connectivity,Frequency Response from 30 hz or lower to 20khz or higher ,Signal-to-Noise Ratio 70dB or hgiher ,Crosstalk >70 dB or higher. Should have all Protection fetures like Short-Circuit, Over and Under-Voltage, Over-Current, Over-Load, DC Output, Temperature.complete in all respects as approved and desired by the Engineer in-charge at site.

SITC of POWER SEQUENCER ,MCU controlled smart power management system, TFT LCD screen with voltage + status indicators, 10 channels or higher, controllable power output sockets, with each channel programmable delay on/off time, max 16A output per socket & 60A max total output, Smart over and undervoltage management with cut off, relay on/off with delay timer, RS232/485, network control interface availablecomplete in all respects as approved and desired by the Engineer in-charge at site.