SPECIAL REPAIR TO BLDG NO.P-9 AND P-32 AT RAPP SCHOOL ,PROV OF 3X TOILET, 3X BATHROOM , 2 X WASH BASIN WITH MIRROR NEAR JCO MESSS AT ROWRIAH ,PROV OF KOTA STONE IN BLDGS NO.T-46 AT ROWIAH AND SPECIAL REPAIR TO BLDG NO P-56 AT LICHUBARI N JORHAT MILI

Amount

Dismantling asbestos cement (corrugated / semicorrugated, etc.) sheeting in roof covering including ridges complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as directed.

Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) complete all as directed.

Dismantling timber scantling in unframed work, 40 Sq cm and over in section, in any position, complete all as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as directed.

Taking down cement plaster from brick or concrete surfaces of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as directed.

Demolition of Cement Concrete of any description and in any position complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) n. exc. 1.5 Sq. M each, complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) exc. 1.5 Sq. M but not exc. 4.0 Sq M each, complete all as directed.

Taking up or down, steel tubing 15 mm bore, and connection including cleaning for re-fixing or removal from site of work complete all as directed.

Taking up or down, steel tubing 20 mm bore, and connection including cleaning for re-fixing or removal from site of work complete all as directed.

Demolition and breaking up drain pipes up to 150mm dia (Salt glazed ware, AC or Reinforced concrete) set in cement mortar

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil, complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil ,complete all as specified and directed.

Returning filling in soft/loose soil, including, spreading levelling watering and well ramming in layers not exc. 25 cm complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 Metres and depositing where directed at a level n. exc. 1.5 M above the starting point complete all asspecified and directed.

Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering with miniumum compaction required 95% proctor density , complete all as specified and directed.

Materials and Labour for, broken stone or boulder hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface , complete all as specified and directed.

Materials and Labour for sand filling under floors or in foundations including watering and consolidation, complete all as specified and directed.

M & L for polythene film, black, 50 micron laid in floors conforming to IS 1508 complete all as specfied and directed

Materials and Labour for plain cement concrete (1:4:8) Type D-2 using 40 mm graded aggregate in foundations, filling and mass concrete complete all as specified and directed.

Materials and Labour for reinforced cement concrete M-25 design mix in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete ,complete all as specified and directed.

Materials and Labour for reinforced cement concrete M-25 design mix in columns; pillars; piers; posts; struts etc,complete all as specified and directed.

Materials and Labour for reinforced cement concrete M-25 design mix in chajjas,complete all as specified and directed.

Materials and Labour for reinforced cement concrete M-25 design mix in beams, cantilever, bressumers, lintels over 1.5M Span,complete all as specified and directed.

M&L for RCC design mix M-25 in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves , baffle wall and the like slabs etc. complete all as specified & as directed.

Use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sided and soffits of plinth beams and similar works; vertical or to batter for rough finished surfaces of concrete, flat, complete all as specified and directed.

M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), work in rough finished flat surfaces of concrete complete all as specified and directed.

Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings , girders, bressummers, lintels, cantilevers, shelves including supports,overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete, flat, complete all as specified and directed.

Use and waste of form work to chullah hoods, chajjas,troughs and similar items including edges for fair finished surfaces of concrete, flat, complete all as specified and directed.

Use and waste of form work to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surfaces of concrete, square, rectangular or polygonal, complete all as specified and directed.

Materials and Labour for plain cement concrete (1:3:6) type C2 using 40 mm graded aggregate as in surface channels and drains complete all as specified and directed.

M & L for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed.

Materials and Labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded aggregates as in plinth protection/floor including finishing surface even and smooth without using extra cement complete all as specified and directed.

M & L for damp proof course to horizontal or vertical surfaces including necessary formwork, 25mm thick, in cement concrete 1:2:4 type B0 complete all as specified and directed.

Materials and Labour for 25 mm thick plain cement concrete (1:2:4) type B0 using 12.5 mm graded aggregates as in sub floor/pavings complete all as specified and directed.

Materials and Labour for 100 mm thick plain cement concrete (1:4:8) type D2 using 40 mm graded aggregates as in sub floor/pavings complete all as specified and directed.

Materials and Labour for plain cement concrete (1:2:4) type B0 using 12.5 mm graded aggregate in lintels up to 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary from work complete all as specified and directed.

M & L for precast cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces fair faces, including chamfers, weatherings, throating etc. and setting in cement mortar (1:4) complete with joints to match complete all as specified and as directed

M&L for cement concrete 40mm thick type B-0, 1:2:4 (12.50 mm graded aggregate) as in flooring, finished even and smooth using extra cement all complete as specified and as directed

Materials and Labour for, Digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm,conforming to IS 15622, Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:4),complete all as specified and directed.

Materials and Labour for, Digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,conforming to IS 15622, Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:4),complete all as specified and directed.

Material and Labour for Digital Vitrified Ceramic Tiles, , 10 mm thick (square/rectangular) polished area of each tile not exceeding 0.36 Sq M, on floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 20 mm thick screed bed or bedding layer of cement mortar (1:6), complete all as specified and directed.

Material and Labour for Digital Vitrified Ceramic Tiles,, 10 mm thick (square/rectangular) polished area of each tile not exceeding 0.36 Sq M, on vertical surfaces of wall such as dados, skirting etc., set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 15 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed.

Materials and Labour for, Digital glazed ceramic coloured tiles, 400 X 400 X 7mm thick, conforming to IS 15622, Grade B III, on vertical surface of wall such as dados, skirting etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed.

Material and Labour for chequered ceramic tiles, coloured, 12 mm thick (square/rectangular) area of each tile exceeding 0.09 Sq M but not exceeding 0.16 Sq M, conforming to IS 4457-2007, on floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour,over and including 20 mm thick screed bed or bedding layer of cement mortar (1:6), complete all as specified and directed. MAKE:- (Johnson ‘Endura’/ Somany ‘Durastone’/ Regency ‘Duro’)

M & L for 20mm thick granite tiles (any type) machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing match colour,over and including 20 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed.

M & L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing match colour,over and including 20 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed.

M & L for kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed base and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15 mm thick screed bed or bedding layer of cement mortar (1:3), complete all as specified and directed.

Materials and Labour for brick work with Sub Class ‘B’ bricks straight or curved on plan exceeding 6M mean radius built in cement mortar (1:6), complete all as specified and directed.

Materials and Labour for brick work with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in CM (1:4),complete all as specified and directed.

Material and Labour for pre-painted, galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50 mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self-tapping screws, complete all as specified and directed.Make(Tata bluescope/Sexena Marine Tech/Dyna )

Material and Labour for pre-painted, galvalume aluminium zinc coating GI based plain steel sheet, 0.50 mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self-tapping screws, complete all as specified and directed.(Tata bluescope/Sexena Marine Tech /Dyna)

Supply and Fix, plain, galvanised, 1.00mm thick, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed)) with the grade of Zinc coating 275 including dismantling of existing one complete all as specified and directed.

Supply and fix mild steel TMT bars 10 mm dia. and over, cut to length, bend to shape required including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed

Supply and fix mild steel TMT bars 5 mm dia. and over up to and including 10 mm dia. in stirrups, spacers, binders etc. cut to length, bend to shape required including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed.

S & F hot rolled medium and high tensile structural steel of grade E 250 quality C conforming to IS 2062: 2011 as in rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and as directed.

Supply and fix Steel ventilator with centre hung shutters including two pairs of brass cup pivots,catch spring and pulley wheel all as specified and directed.

Supply and Fix, pressed steel frames, size 105 x 60mm, for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified and directed.

Supply and fixing of aluminium sliding window with powder coating (minimum thickness of powder coating 50 micron) including following components / specifications complete all as specified and as directed. (i) Two leaf glazed sliding shutter and one leaf gauged (fly proofing) sliding shutter. (ii) Opening of windows exceeding 0.90 Sqm but not exceeding 1.50 Sqm (iii) Thickness and weight per metre length of aluminium frame and section of shutter all as shown on drawing. (iv) All vertical/ horizontal joints shall be of extruded aluminium section so as to avoid any play between jointed members. (v) All other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, etc. (vi) Rest all as specified in drawing no CEZ/2015/TD/007 Sheet no 1R/5, 2R/5, 3R/5, 4R/5 & 5R/5. Note: 1. Sheet glass, aluminium grill and stainless steel wire mesh shall be measured and paid against respective items of BOQ and all other items as shown on drawing shall be included in quoted rate. 2. Mode of Measurement : Only opening size of window shall be measured.

S&F aluminium anodised grill of design "DG - 104" pattern made out of 7.5 mm plate and finished grill have 7.5 mm width and 6 mm thick complete all as per manufacturer instruction. Make : Decogrille or equivalent model of makes as approved by the GE.

S&F Glazing with sheet glass 5 mm thick ordinary quality in panels of aluminium windows, ventilator, etc. fixed with glazing clips, rubber beading and EDPM gasket in square not exceeding 0.5 Sqm in each pane.complete all as specified and as directed

S & F anodised aluminium frame powder coating (Minimum thickness of powder coating 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc with complete all as specified and directed

S & F for Anodised aluminium door shutters with powder coating of any colour (Thickness of powder coating not less than 50 micron), aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified.

M & L in repair for 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work with including teak wood lipping 6mm thick complete all as specified and directed.

S & F aluminium (Extruded section) body door closer, hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 60 to 80 kg

Supply and Fix, factory made rigid lam PVC door frame of size 125 mm x 50 mm, double rebated with wall thickness of extruded 5mm PVC sheet of density 600 kgs/cum , made by joining 3 Nos. heat bent PVC sheet 'C' channel of 5mm PVC foam sheet of size 35mm x 35mm x 25mm & 40mm x 55mm x 40 mm & 25 mm x 35 mm x 35 mm using solvent cement, the two side 'C' channel shall be reinforced with 19mm x 19 mm MS square tube of 19 SWG with all three 'C' ed to flat base of 5mm PVC sheet with solvent cement. The profile shall be mitred cut at two corners and jointed by inserting 4 Nos. 150 mm long brackets of 15mm x15 mm MS square tube inside the 19 mm square tubes. The two vertical members of door frame shall be reinforced with 40mm x 20 mm MS tubes of 19 SWG duly filled with 2nd class hardwood throughout the frame. The door frame shall be fixed to the wall using 100 mm long nikel coated dry wheet screws through the frame by using PVC fastener. Minimum 08 Nos. of screws shall be provided for each vertical member and minimum 04 Nos.for horizontal members etc. as per manufacturers specifications, fixed in opening, complete all as specified and directed.

Supply and fix solid PVC door frame of size 50 mm X 47 mm made out of 5 mm single side prelam PVC sheet with edges painted to match with prelam sheet, reinforced with MS square tube, fixed in opening, complete all as specified and directed.

Materials and Labour , Factory Made Solid PVC Moulded Door designer Shutter, with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC sheet on back face, supplying & fixing in frame at site as per specification and drawing, complete all as specified and directed.

Supply and Fix, factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded prelam PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail: Panelling of both sides prelam PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, fixed to door frame complete all as specified and directed.

Supply and Fix,IS markedStainless steel butt hinges, medium weight, cold rolled 100 mm size complete all as specified and directed

Supply and fix Aluminium anodized barrel tower bolts of extruded section, 200 mm long complete all as specified and directed.

Supply and Fix, aluminium handles, cast type, anodized, 150 mm size, complete all as specified and directed.

Supply and Fix, aluminium handles, Fabricated type, anodized, 150 mm size, complete all as specified and directed.

Supply and Fix,4 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane complete all as specified and directed.

Supply and Fix, Aluminium Alloy, anodised, sliding door bolt, length of bolt 300 mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Materials and Labour for mild steel works, conforming to Fe 290, Grade E-165 , in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles, complete all as specified and directed.

Materials and Labour for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290, Grade E-165 complete all as specified and directed.

Supply and Fix, stainless steel wire cloth, 0.36mm nominal dia. of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

M&L providing and fixing of false ceiling with powder coated exposed GI grid suspension system (E-grid T-2420 or equivalent of Armstrong having load carrying capacity of 12.5 Kg/M3 with mid span deflection not exceeding 1/360 span with hanger spacing of 1200 mm c/c) consisting of Main Runner 3600 mm long, Cross Tee 1200/600 mm long and Wall Angle. The wall angle shall be fixed on PVC dash fasteners on the perimeter of the wall with steel screws with distance 300 mm c/c. The main runners to be placed @ 1200 mm, the cross tee 1200 mm will be inserted in the pre-cut slots of Main Runner at regular interval of 600 mm to form a modular grid of 1200x600mm. Additional cross tees of 600 mm shall be placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600 mm x 600 mm with and including 6 mm thick HSPC (High pressure steam cured) oceanic pre primed, self embossed, textured designer board, water, termite & fire resistant for insulation and acoustic purpose to be placed in the grid system duly suspended with 4 mm dia GI bar hangers fixed with steel dash through fasteners from purlins with butterfly clips (wt 0.007 kg/clip), hold down clips (wt-0.0035 Kg/clip), with provn of light fixture complete all as per manufacturer instructions and as directed. Make Armstrong/Everest

Material and labour for (seamless) suspended ceiling which includes GI perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and web of 27mm) along with perimeter of ceiling, fixed with screw to brick wall with half of nylon sleeves and screws at 610mm center to center. Then suspended GI intermediate channels of size 450mm (0.90mm thick with two flange of 15mm each) from soffit at 1220mm center to center with ceiling angle of width 25mm x 10mm x 0.55mm thick fixed to soffit, trusses rafters or pipe etc. with GI cleat and steel expansion fasteners Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to intermediate channel with the half of connection clip and in direction perpendicular to the intermediate channel at 457mm center to center 12.50mm thick gypsum board (conforming to IS-2095-1982) is then fixed with screw to ceiling section with 25mm dry wall screw at 230mm center to center. Screw fixing is to be done mechanically either with the driver or drilling machine with suitable attachments. and then finally the boards are to be jointed and finished so as to have flush look which includes filling and finishing the tapered and square edges of the boards with jointing compound, joint proper tape as per manufacturer instruction all as specified and directed

M & L for second class hard-wood in clean sawn timber fixed and wrought, in scantlings in unframe works and any position fixed with nails complete all as specified and directed

M & L for 6mm thick (5 ply) plywood, grade BWR, type BB, fixed with screws to timber frame work complete all as specified and directed

Material and labour for pre-fabricated glass fiber reinforced gypsum beads/cornices architecturally beautifully crafted decorated 100 mm wide all as specified and directed.

Supply and fix pre-fabricated glass fiber reinforced gypsum mouldings/ corners of approved architectural design and make all as specified and directed

Material and labour for pre-fabricated glass fiber reinforced gypsum mouldings of Architectural design of circular panels n.exc 75cm dia all as specified and directed.

M & L for chamfer, spays, grooves rebates, rounded angles, rounded nosings, tongued and grooved edges (each tongue and groove measured) etc exc 3mm but n. exc 75mm girth on hard wood including moulding complete all as specified and directed

S&F in repairs Gratings chromium plated 140 mm dia fixing in floors with neat cement slurry to match, etc. complete all as directed.

Supply and Fix in repair PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle, of capacity 10 Litres, including brackets, flush pipe, complete all as specified and directed.

Supply and Fix PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle, of capacity 10 Litres, including brackets, flush pipe, complete all as specified and directed.

Supply and fix PVC connections 15 mm size with PTMT nuts of length 450 mm,complete all as specified and directed.

Supply and Fix, brass chromium plated, towel rail, 20mm dia, 60cm long between flanges, complete all as specified and directed.Make Jaquar or equivalent of Marc/Kohler

Supply and Fix, in repair bib tap, cast copper alloy, fancy type, brass chromium plated,long body with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule,15 mm bore and fixed, complete all as specified and directed.

Supply and Fix, brass CP fancy wall mixer Wall Mixer 3-in-1 System with Provision for both Hand Shower and Overhead Shower Complete with 115mm Long Bend Pipe, Connecting Legs & Wall Flange (without Hand & Overhead Shower)for mixing hot & cold water screwed down for iron pipe 15 mm bore and fixed, complete all as specified and directed. ( wall mixer cat part no. QQT-7281 of Jaquar or equivalent make Kohler/Marc)

Supply and Fix, brass CP fancy centre hole basin mixer for mixing hot & cold water screwed down for iron pipe 15 mm bore and fixed, with including hand shower and tube inlcuding taking out unserviceable existing one complete all as specified and directed. (Make mixer cat part no. QQT-7169B of Jaquar or equivalent make Kohler/Marc)

Supply and Fix, in repair stop valves/Angle cock, cast copper alloy, fancy type, brass chromium plated,screwed down, high pressure with crutch or butterfly handle, screwed both ends for steel pipe of for unions, 15 mm bore, complete all as specified and directed.

Supply and Fix,in repair stop valves, cast copper alloy , fancy type, chromium plated, screwed down, high pressure with long shank and cup (concealed type), screwed both ends for steel pipe of for unions, 15 mm bore, complete all as specified and directed.Make:Cat No.KUB-35053F of Jaquar or equivalent make of Marc/Kohler)

Supply and Fix, Pillar Cock with 200mm Extension Body & Base Flange, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe, 15 mm bore, including taking down existing unserviceable one complete all as specified and directed.Make:Cat No.KUB-35021of Jaquar or equivalent make of Marc/Kohler)

Materials and Labour for galvanized steel tubing, medium grade, 15 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor, complete all as specified and directed.

Materials and Labour for galvanized steel tubing, medium grade, 20 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor, complete all as specified and directed.

S&F 75mm bore chromium plated shower rose with shower arm of 15mm dia (size of arm 195mm long with bend to 45 degree) complete all as specified and as directed (Make: Jaquar/Marc/Kohler)

S&F 500 ltrs IS marked multilayer rotational moulded polythytene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position with and including 20mm PTMT ball valves high pressure with polythene float and nut with and including dismantling exsiting one complete all as specified and directed .

S&F 1000 ltrs IS marked multilayer rotational moulded polythytene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position with and including 25mm PTMT ball valves high pressure with polythene float and nut with complete all as specified and directed .

Supply and Fix vitreous China wash down water closet pan (pedestal pattern), white, (including fixing bolts, flushing cistern and flush pipe connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe etc.including PVC seat cover and taking out of existing one and making good disturbed surfaces as per existing specification complete all as specified and directed.

S & F in repairs wash basins, vitreous china, white, flat back, size 550 mm X 400 mm with and including cast iron brackets (embedded in wall upto 110 mm depth with and including cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate or fixing on wall with and including rawl plug and screws), 32 mm nominal size, copper alloy, nickel chromium plated finish waste fittings, including painting of fittings and brackets, sealing gap between wall and basin with silicone sealant, cutting and making good the walls wherever required and connecting to supply pipes, waste pipes, waste fittings etc. with silicone sealant complete all as specified and as directed.

S & F wash basins, vitreous china, white, flat back, size 450 mm X 300 mm with and including cast iron brackets (embedded in wall upto 110 mm depth with and including cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate or fixing on wall with and including rawl plug and screws), 32 mm nominal size, copper alloy, nickel chromium plated finish waste fittings, including painting of fittings and brackets, sealing gap between wall and basin with silicone sealant, cutting and making good the walls wherever required and connecting to supply pipes, waste pipes, waste fittings etc. with silicone sealant complete all as specified and as directed.

Materials and Labour for Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe), including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; fixing, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), complete all as specified and directed.

Materials and Labour for Vitreous China Urinal partition white of size 310mmX700mm complete all as specfied and directed

Supply and Fix in repair vitreous China Squatting pan ‘Orissa’ pattern, size 580 X 440 mm, white, with integral foot rests and with ‘P’ or ‘S” trap, (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, etc and including provision of cement concrete bedding, complete all as specified and directed. (Make Cat part no.20042 of Hindware or equivalent make of parryware/Cera

S & F unplasticized PVC pipes as per IS 4985: 2000, of class 5, working pressure PN 10 (1 Mpa), plain or socket ended and nominal size 150 including all fittings and fixtures fixed to walls, ceiling or in laid in trenches with elastomeric sealing ring joints complete all as specified and as directed.

Supply and Fix 110 mm bore UPVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls, complete all as specified and directed.

Supply and Fix, 75 mm bore UPVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls or laid in trenches with including fittings, complete all as specified and directed.

Supply and Fix, 75 mm bore PVC (SWR) bends any radius, with access door, complete all as specified and directed.

S&F 75mm dia PVC(SWR) junction single, (single T) equal or unequal with access door complete all as specified and as directed.

S&F 110mm dia PVC(SWR) junction single, (single T) equal or unequal with access door complete all as specified and as directed.

Supply and Fix, 110 mm bore PVC (SWR) bends any radius, with access door, complete all as specified and directed.

S & F 110mm bore PVC (SWR) vent cowl complete all as specified and directed.

Supply and Fix, in repair PVC (SWR) floor trap, plain with grating including jointing with solvent cement with dia. of out let 75 mm, complete all as specified and directed.

S & F for 110 mm bore PVC (SWR) Tee,branch piece, bends, single (single Y) equal or unequal, complete all as specified and directed.

M & L for PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed.

Supply and Fix, in repair soap dish, fixed in wall, complete all as specified and directed.Make Catpart no.AQN-7731 of Jaquar or equivalent make of Kohler/Marc

Supply and Fix, gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe, 15 mm bore, complete all as specified and directed.

S&F 50 mm dia low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. cm fixed complete to walls, ceiling or in floors etc including cutting, chasing, pinning and making floor good with existing one all as directed

Material and Labour for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel and iron surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

Materials and Labour for rendering 5 mm thick, cement plaster, in cement mortar (1:4) mixed with water proofing compound as per manufactures instructions over and including 10mm thick backing coat in cement mortar (1:4) on fair faces of brick work or concrete surface in walls, complete all as specified and directed. Note: - (Water proofing compound will be measured and paid separately)

Materials and Labour for rendering 15 mm thick, cement plaster, in cement mortar (1:4) on surface fair face of brickwork in walls and finishing surface even and smooth without using extra cement, complete all as specified and directed.

Materials and Labour for rendering 15 mm thick, cement plaster, in cement mortar (1:6) on surface fair face of brickwork in walls and finishing surface even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of new plastered or un -plastered from walls, and applying two coats acrylic distemper on walls, over and including a coat of 3 mm thick white wall care putty over a coat of primer complete all as specified and as directed.Make;Berger (Bison)/J&N(Jensolin)/Asain Piants(Tractor)/Nerolac(Beauty)

M&L for complete removal of existing treatment from walls, and applying two coats acrylic distemper on walls, over and including a coat of 3 mm thick white wall care putty with and including a coat of primer complete all as specified and as directed.Make;Berger (Bison)/J&N(Jensolin)/Asain Piants(Tractor)/Nerolac(Beauty)

Material and Labour for applying three coats of white wash to new plastered surfaces on walls including preparation of surfaces complete all as specified and directed.

Material and Labour applying two coat of100 % Acrylic Exterior Emulsion paint (Berger,Weather coat Advanced XP Brand/Asain Paints :Apex ultima Brand /ICI:Dulux Weather shield Max Brand/J&N:Safeguard Optima Brand painting over and including a coat of primer to new plastered or unplastered surfaces on walls including preparation of surfaces, complete all as specified and directed.Note (Work shall be exectuted through authorised applicator and shall be got approved by GE before commencement of work)

Material and Labour for complete removal of existing treatment by means mechnical process / Machine as directed by manfucaturer through authorised applicator of manufacturer,s and applying two coat of100 % Acrylic Exterior Emulsion paint (Berger,Weather coat Advanced XP Brand/Asain Paints :Apex ultima Brand /ICI:Dulux Weather shield Max Brand/J&N:Safeguard Optima Brand painting over and including a coat of primer to old plastered or unplastered surfaces on walls including preparation of surfaces, complete all as specified and directed.Note (Work shall be exectuted through authorised applicator and shall be got approved by before commencement of work)

Supply only integral water proofing compound all as specified

Material and Labour for applying two coats of cement-based paint, white or tinted to new plastered surfaces on walls including priming with alkali resistant priming paint and including preparation of surfaces complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Taking down copper/aluminium sub main wiring complete and removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

M&L for concealed type wiring using approved colour coding as per IS for one light/ fan/ bell point controlled by one switch with1.5 Sqmm (Nominal area) PVC insulated, unsheathed, multistranded copper, conductor cable FRLSH (1100Volts grade) drawn in and including heavy duty PVC rigid conduits of 20/25 mm dia with all fittings and accessories alongwith PVC insulated multi stranded copper conductor of size 1.5 Sqmm as earth continuity conductor including fixing of 1. 22mm thick MS sunk terminal box duly flushed to wall with 3mm thick plastic laminated/ebonite sheet cover fixed with brass screws,cap and washers complete all as specified and as directed. Note:- (i) The chases in the wall shall be cut with elect cutter (ii) The disturbed surfaces of wall shall be made good with cement plaster 1:4 including matching the surfaces with as per existing finishes and to the entire satisfaction of Engineer in Charge

All as per item No- 140 as above but for one 3/5 pin socket outlet 5 Amps on the same board with other switches.

M&L for concealed type wiring using approved colour coding as per IS for switch socket combination 15 amps 5/6 Pin point on Independent board with 4 Sqmm (Nominal area) PVC insulated, unsheathed, multistranded copper, conductor cable FRLSH (1100Volts grade) drawn in and including heavy duty PVC rigid conduits of 20/25 mm dia with all fittings and accessories alongwith PVC insulated multi stranded copper conductor of size 2.5 Sqmm as earth continuity conductor including fixing of 1. 22mm thick MS sunk terminal box duly flushed to wall with 3mm thick plastic laminated/ebonite sheet cover fixed with brass screws,cap and washers complete all as specified and as directed. Note:- (i) The chases in the wall shall be cut with elect cutter (ii) The disturbed surfaces of wall shall be made good with cement plaster 1:4 including matching the surfaces with as per existing finishes and to the entire satisfaction of Engineer in Charge

M & L wiring for circuit/Sub main wiring concealed type with two single core cable PVC insulated cable with 6.00 Sqmm (Nominal area) multi stranded copper conductor FRLSH cable 1100 volts grade including earth continuity conductor using PVC insulated cable of stranded copper conductor of size 4 Sqmm connected to common earth dolly and drawing into and including steel conduits of size 20/25 mm dia medium grade including making good the disturbed surfaces to match with existing surfaces complete all as specified and as directed. Note:- (i) The chases in the wall shall be cut with elect cutter (ii) The disturbed surfaces of wall shall be made good with cement plaster 1:4 including matching the surfaces with as per existing finishes and to the entire satisfaction of Engineer in Charge

Supply and Fix, switch piano, flush button, single pole, one way, 5 Amps, complete all as specified and directed.

Supply and Fix, switch socket combination 2 in 1, 5 pin, 15 Amp, flush type universal, complete all as specified and directed.

S & F Socket outlet, 3 pin, 5 Amp, Flush type complete all as specified and directed.

Supply and Fix, ceiling rose, three terminal, PVC/ Polycarbonate insulated body, complete all as specified and directed.

Supply and Fix stepped type electronic fan regulator, flush type, on existing phenolic laminated sheet etc. as required , complete all as specified and directed.

Supply and laying common burnt clay building bricks, sub-class ‘B’ designation 75, old size bricks, in cable trenches, as cable protection, complete all as specified and directed.

Supply and filling in approved dry sand in cable trenches before and after the cables are laid, as in sand cushioning to cables, complete all as specified and directed.

Supply,laying, jointing and testing of LT, XLPE insulated, PVC sheathed, armoured, heavy duty electric cables with aluminium conductor for working voltage up to and including 1100 volts, of cross sectional area 16 sq. mm, 2 core, including with suitable size of lugs including taking out existing one complete all as specified and directed.

Supply,laying, jointing and testing of LT, XLPE insulated, PVC sheathed, armoured, heavy duty electric cables with aluminium conductor for working voltage up to and including 1100 volts, of cross sectional area 25 sq. mm, 3 ½ core, including with suitable size of lugs including taking out existing one complete all as specified and directed.

Supply and Fix lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings,complete all as specified and directed.

Supply and Fix, LED lamp, 10 Watts, lumen output 770 lm, colour temp 6500 K, lamp current 0.04 amp, lamp base cap B22, complete all as specified and directed.

S&F Decorative ultra slim linear LED lighting fixture with co extruded polycarbonate body environmental friendly, E-lite LED GREEN 20W, 240 Volt, LED tube light as per Havells Cat No. LUMILINEBS20WLED865SPCWH or equivalent of philips/Bajaj/wipro and including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.50 Sq mm, 3 core, 1100 Volts grade, from light fitting to point outlet, complete all as specified and directed.

S&F Decorative ultra slim linear LED lighting fixture with co extruded polycarbonate body environmental friendly, 10W, 240 Volt, LED tube light as per Wipro Cat No. LL20-111-XXX-65-NE or equivalent of philips/Bajaj and including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.50 Sq mm, 3 core, 1100 Volts grade, from light fitting to point outlet, complete all as specified and directed.

S & F 18 Watt 230 volt 50 Hz LED type new generation energy saving building security light luminiries housing is of versatile pressure die cast aluminium IP 66 with high power LED light complete with ballast/charging unit including of all accessories prewired including connecting up with 2.5 sqmm multi stranded aluminium conductor 2 core cables not less than 2 m of length fixed to pole/wall etc and testing with and including 1.5mtr GI pipe 40mm dia light grade bracket bend to shape ,clamps,nuts,bolts and washer complete all as specified and directed. Make: Wipro cat part No. LR06-241-XXX-57-XX or equivalent of philips/CG.

S&F Square with Recess/Suspended Type Luminaire LED lighting fixture with Powder Coated White Aluminum Fixture Material environmental friendly, Colour Temperature 6500K 36W, 240 Volt, LED,s with driver as per CG Cat No. LCPL-36-CDL(2X2). or equivalent of philips/Bajaj/wipro and including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.50 Sq mm, 3 core, 1100 Volts grade, from light fitting to point outlet, complete all as specified and directed.

Supply and Fix, Heavy Duty Exhaust Fan with self closing metallic louvers, 300 mm sweep, 1400 RPM, Single Phase, 230 V, 50 Hz, all as per Model “Turbo Force” of Make ‘Havells’ or equivalent Model of Make ‘Usha’ / ’Crompton Greaves’/’Almonard’ and connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 1.50 Sq mm, 3 core, 1100 Volts grade, from ceiling rose/ connector to fan complete all as specified and directed.Note: Cost of cutting and making hole for fixing exhaust fan shall be deemed to included in quoated rates

Supply and Fix, 6M Flush type with AC Starter, 20Amps MCB Plug top with Indicator , 6 moudule plate including connection,complete all as specified and directed. Wipro(Northwest) cat part No. ACPU6M-FT or equivalent make

Supply and Fix, 6M metal box GI 20G for mounting of AC Starter complete all as specified and directed. Wipro(Northwest) cat part No.MB06M20GGI or equivalent make

Supply and Fix, miniature circuit breaker (MCBs), single pole and neutral, 240 Volts,10KA, 40 Amps "C" series complete all as specified and directed.

Supply and Fix, double door, sheet metal enclosure for DBs for mounting of MCB for 240 Volts, 6 way, with 200 Amps rated bus bar, Single Pole & Neutral, , including dismantling taking down unserv. DB complete all as specified and directed Cat No.DBSPN006DD of Make L&T or equivalent Model of Make Legrand/Siemens]

Supply and Fix, double door, sheet metal enclosure for DBs for mounting of MCB for 240 Volts, 4 way, with 200 Amps rated bus bar, Single Pole & Neutral, , including dismantling taking down unserv. DB complete all as specified and directed Cat No.DBSPN004DD of Make L&T or equivalent Model of Make Legrand/Siemens]

Supply and Fix, double door, sheet metal enclosure for DBs for mounting of MCB for 240 Volts, 8 way, with 200 Amps rated bus bar, Single Pole & Neutral, , including dismantling taking down unserv. DB complete all as specified and directed Cat No.DBSPN008DD of Make L&T or equivalent Model of Make Legrand/Siemens]

Supply and Fix, miniature circuit breaker (MCBs), single pole, 240 Volts,10KA, 6-32 Amps "C" series complete all as specified and directed.

Taking out existing unserviceable armoured electric cables,1100 volts,cross sectional area 16 sq. mm, 2 core from trenches/ducts/poles etc.,complete all as directed.

Supply and Hanging, ceiling fan, rating 240 V, 50 Hz, Single Phase, 32 watt, 1200 mm sweep with down rod, canopy, fan blades and accessories, BEE 5 Star Rated, service value more than 5.1 all as per Model “USHA ENERGIA 32 5 STAR” of Make ‘USHA’ or equivalent Model of Make ‘Havells’/’Crompton Greaves’/’Almonard’ , and connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.50 Sq mm, 3 core, 1100 Volts grade, from ceiling rose/ connector to fan complete all as specified and directed.

Supply and Laying galvanized steel tubing, 40 mm bore, light grade, in trenches or fixed to poles/Walls etc., for cable protection, complete all as specified and directed.

Materials and Labour for earthing complete with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.5M below normal ground level connected to galvanised steel earth lead wire 4 mm dia. by means of bolts, nuts check nuts and washers of galvanised steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 54 cm x 54 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm centre to centre both ways, with one handle for lifting made out of 8 mm dia. MS bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 15 mm bore galvanized steel tubing medium grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown on electrical plate No 3 of SSR Part –I (2009)

M/S GOPAL ROY AND CO

A M CHOUDHURY AND CO