Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹33.1 LAccepted-AOC NO 14 SMALL STREET MANAPET PO BAHOUR COMMUNE PUDUCHERRY 607 402 | CUDDALORE | TAMIL NADU | 607402 | L1 | Accepted-AOC Single bidder |
Tender Value
₹32.3 L
EMD Value
₹64,574
Closing Date
20 Jun 2024, 4:30 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
The Executive Engineer, PWD, Mahe
Public Works Department, Mahe. Near Sub Court, Mahe
Improvements to the Regional Administrator residence at First Floor of Regional Administrator Office
2024_PWDC2_15740_1
12/EEM/24-25/07(24-25)
Open Tender
Civil Works
Item Rate
90 days
Work at Mahe
Please refer Tender documents.
8 documents required · 8 mandatory
₹525
₹64,574
27 Dec 2024
11 Jun 2024
21 Jun 2024
11 Jun 2024
20 Jun 2024
11 Jun 2024
Amount
Code No. Derived NON PSR:- Providing and fixing marine plywood 12mm thick with necessary screws including priming coat and unexposed surface.
Code No. 9.134.2.1.1M:- and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws - 30 mm thick shutters - With ISI marked M.S.pressed butt hinges bright finished of required size - Malabar Ist class teak wood
Code No. 10.16.1:- Steel work in built up tubular (round,square or rectanglar hollow tubes etc.) trusses etc., including cutting , hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete - hot finished welded type tubes
Code No. 10.28:- Providing and fixing stainless steel (grade 304) railing made of hollow tubes, channels, plates etc., including welding ,grinding. Buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete. i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.,)
Code No. 11.63.3:- Providing and fixing homogeneous Polyvinyl chloride sheet in flooring and skirting in approved pattern on a smooth and damp proof base using rubber based adhesives of approved quality including rolling with light wooden roller weighing about 5 kg. All complete - 2 mm thick sheet
Code No. 13.26A:- Providing and applying ready mixed wall putty (JK / Birla) of 2 mm thickness over plastered surface to prepare the surface even and smooth complete
Code No. 13.48.1:- Finishing with deluxe multi surface paint system for interiors and exteriors using primer as per manufacture's specification - Two or more coats applied on walls @ 1.25 ltr / 10 sqm over and including one coat of special primer applied @ 0.75 ltr / 10 sqm
Code No. 13.61.1:- Painting with synthetic enamel paint of approved brand and manufacutre to give an even shade - Two or more coats on new work
Code No. 15.39.1:- Dismantling wooden boardings in lining of walls and partitions , excluding supporting members but including stacking within 50 metres lead - upto 10mm thick
Code No. 15.57:- Dismantling aluminium / gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 metres lead
Code No. 15.58:- Demolishing R.C.C. work by mechanical means and stockpiling at designated locations and disposal of dismantled materials upto a lead of 1 kilometre , stacking serviceable and unserviceable material separately including cutting reinforcement bars
Code No. 16.97:- Providing and fixing PVC false roofing with the existing PVC cabin using sintex PVC section of size 6mm x 250 mm , having interlocking facilities supported in the PVC extruted multi chamber frame section of 40 x 48 mm , with necessary MS / Stailess screws. The rate includes the cost of sintex PVC section , labour charges for fixing and transport etc.complete
Code No. 16.118:- Supply and fixing of sliding windows at all levels made out from Unplasticised Poly vinyl chloride frame (UPVC) of natural colour (PRISTINE WHITE) with outer frame of size 40 x 56x40mm / 102 x 56x 40mm and for shutter frame of size 53 x 38 x37 mm for two track / three track sliding widows , with wall thickness of 1.8mm (+/-0.3mm). The section should be single glazing using (flush catch) single point locking. The gasket should be made of EPDM (Ethylene propylene dimonomer) and applying silicon sealents (GE make or wacker make) outside and acrylic sealent inside including single glazing of 5mm thick clear float glass . The sections should be reinforced with GI sheet of 1.5 mm thick with suitable drainage grouting
Code No. 21.2.1:- Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 grade I type II , in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings- Pre - laminated particle board with decorative lamination on one side and balancing lamination on other side
Code No. 21.3.2:- Providing and fixing glazing in aluminium door, window , ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings ( cost of aluminium snap beading shall be paid in basic item) - with float glass panes of5.50 mm thickness
Code No. 21.18:- Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture , including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete (Door handle, lock and stopper etc. to be paid separately)
Code No. 21.1.1.1:- Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions , i.e at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling , C.P.brass / stainless steel screws , all complete as per architectural drawings (Glazing, paneling and dash fasteners to be paid for separately) - for fixed portion - anodised aluminium (anodised transparent or dyed to required shade according to IS:1868, Minimum anodic coating of grade AC 15)
Code No. 27.9:- Providing and fixing factory made solid Foam uPVC profile for kitchen cabinet frame (45 x 20 mm) of approved shade , quality and make . The profile shall be laminated on both sides , made from rigid foam sheets (Single extruded) having density 600 Kg /cum and the exposed edges sealed with PVC edge beading of same shade and colour. The frame shall be fire retardent with necessary screw holding capacity. Frame shall be fixed to wall using Expendable Fastner with necessary stainless steel screws , all complete
Code No. 27.10:- Providing and fixing factory made Kitchen Cabinet Shutter / Partition 20mm nominal thickness of approved shade , quality and make from rigid foam sheets (single extruded) having density 600 Kg / cum and laminated on both side by laminate Sheet / PVC foil lamination. The exposed edges shall be sealed with PVC edge beading of same shade and colour. The shutter shall be fire retardent having necessary screw holding capacity. Shutter shall be fixed to frame using approved hinges with necessary stainless steel screws , all complete.
Code No. 27.10:- Providing and fixing concealed hinge of approved quality for 19-20mm thick door with stainless steel screws complete
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .