ADDITION ALTERATION UPGRADATION OF CERTAIN OFFRS AND JCOS OR MD ACCN AT SHAJAHANPUR CANTT

Amount

Item B/R

Excavating in post holes ( or similar hoels ) each n exc 0.5 cum getting out, returining, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm , watering, and removing surplus soil to a distance n exc 50 mtr in soft/loose soil.

M&L cement concrete, 1:3:6 type C2 ( using 40 mm stone aggregate) as in filling and mass concrete.

S&F rolled mild steel in joist , channel, angle or tie sections fixed independently without connecting plates etc (cut to ordinary length i.e. within 20 mm of the length indicated) as in posts and struts in fencing including cutting tops to shape as directed , drilling holes , notching for wire etc ,flat iron fillets ( for securing wire etc ) including all necessary drilling , bolting or riveting, etc and similar work , MS flat iron of any size etc complete.

S&F posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, wind ties, etc.; flat iron fillets ( for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165 complete all as directed.

Supply only mild steel screw bolts 5 to 10 mm dia (machine made) with hezagonal or square at one end and screwed the other ends and fitted with washers and one hezagonal or squre nut exc 5 cm but not 10 cm long

M&L Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire

Supply only chain link MS galvanised fencing, any size or type all as specified and as directed

Supply only mild steel round bars in available length of Fe-290 (Gde E-165)

M&L brick work with sub class' B' bricks of old size, straight or curved on plan exc 6 m mean radius built in cement mortar 1:4.

M & L rendering 10mm thick on brick wall or concrete surfaces in cement mortar 1:4 finished fair and even complete all as specified

M & L applying two coats of cement based paint on newly plastered or unplastered wall surface including preparation of surfaces, complete all as specified.

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/loose soil for roads to required slope gradient, camber etc complete all as specified and directed.

M & L hardcore of broken bricks of gauge n.exc.63mm,deposited,spread and levelled in layers n exc. 15 cm thick, watered and well rammed to a true surface.

M&L for 75 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base floor / pavings complete all as specified and directed.

M&L for cement Concrete coloured interlocking paver blocks shall be factory made with casting in rubber/pvc moulds & compacting on a vibro table assembly and shall be cured in curing tank for atleast 14 days and then air dried before use. The paver block shall be confirming to IS 15658 -2006 of 60mm thickness, M-35 Grade. Approved design, shape, size and colour of top layer complete all as specified and directed.

M&L for precast machine pressesd glazed Kerb stone rubber moulded PCC (1:2:4) type B0 using 12.5 mm graded stone aggregrate, including weathering, slightly rounded or chemferred angles and throating , as directed edges complete including excavavtion for kerb stone complete all as specified and directed.

Taking down cement plaster of any description/any thickness on brick, stone, concrete surfaces including racking out joints, hacking for key, scrubbing down with water, removal of rubbish and cleaning, etc complete as directed and specified.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons Laid, bedded and pointed in any mortar etc. complete all as specified and directed

Roughening surfaces of old concrete floor/ terrazo floor/dado by power tool, hacking, picking, sweeping, cleaning and washing down with water to remove dust etc complete all as specified and directed.

Demolition of cement concrete (un-reinforced) of any description and in any postion below or above ground level complete all as specified and directed.

Demolition of reinforced cement concrete, (other than ground floors), shelves, chajjas, slabs and similar work carefully and matching to adjoining disturbed surfaces complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

Taking down chowkats or frames area not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frames area exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Dismantling of 100mm bore cast iron/ pvc drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed.

Dismantling of 75mm bore cast iron / pvc drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed.

Taking up or down 15 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed.

Taking up or down 20 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed.

Taking down wooden chowkat with shutters of area 6 Sqm and n. exc. 10 Sqm complete neccessary fittings required complete all as specified and directed.

M&L PCC 1:5:10 type E-2 as sunken sub base of floor fillings with 40mm broken brick agg .

S&F 32mm dia GI pipe, medium grade as in spout pipe in sunken floor complete all as specified and directed.

M & L 25 mm thick PCC 1:2:4 type B-1, using 20 mm graded stone aggregate as in floors, surfaces finished fair and even complete all as specified and directed.

M&L glazed ceremic colour tiles in vertical surfaces 300x200x 6 to 7 mm thick, set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 10 mm thick rendering in CM (1:4) complete all as specified and directed.

M&L for non-skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specfied and directed.

M & L for 7 to 8 mm thick glazed coloured ceramic tiles ( square/ rectangular) with border , area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, as in vertical surfaces set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles laid over and including 10 mm thick rendering in CM (1:4) complete all as specfied and directed.complete all as specified and directed.

M&L for ceramic floor tiles 8 to 9 mm thick (square / rectangular) area of each tiles exc 0.18 sqm but not exceeding 0.38 sqm in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match with coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

M&L for ceramic tiles 8 to 9 mm thick (square / rectangular )area of each tiles exc 0.18 sqm but not exceeding 0.38 Sqm in vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles incl 10 mm thk cement plaster 1:4 backing coat, complete all as specified and directed.

M&L for vitrified ceremic tiles 8 to 9 mm thick, as approved by GE dark shade / double charged tiles (Square/rectangular) polished, area of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

M&L for vitrified ceramic tiles as approved by GE dark shade/ double charged tiles 8 to 9 mm thick (square/ rectangular) polished area of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm as in vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles 10 mm thk cement plaster 1:4 backing coat, complete all as specified and directed.complete all as specified and directed.

M&L for machine cut mirror polish kota stone slab flooring20-25mm thich over 15mm thick screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigmen to match the shad of the slab including round nosing at corners rubbing and polishing complete all as specified and directed

M&L for machine cut mirror polish kota stone slab 20-25mm thich in riser of step,skirting,dado and pillers over and including 15mm thick rendering in CM 1:4 including rubbing and polishing complete all as specified and directed

M&L for 20 mm thick Granite of any colour (table rubbed and polished) as in windows cill & cooking platforms and like fixed in cement mortar (1:6) including form work , pointing in white cment (1:2) using marble dust with admixture of pigment to match with shade of granite with full round bull nosing edging complete all as specified and directed.

M&L for red stone slab 25mm to 35 mm thick dressed true and square,in one length not less than 60 cm and n exc 120 cm as in plinth protection etc in cement mortar 1:4 punched dressed on exposed faces and self faced on the embedded unexposed beds and joints exposed edges chamfered or rounded as directed and including screed bed of 20 mm thickness in cement mortar 1:6 all as specified and directed

M&L for reinforced cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) (nominal mix) as in slabs supported on wall,landing, balconies, shelves and like including bonding agent , complete all as specified and directed. (Note - Reinforcement to be measured and paid under respective items)

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick for rough finished surfaces of concrete flat, complete all as specified and directed.

M&L for formwork to chuullah hoods,chajjas,troughs and similar items including edges for rough finished flat surfaces of concrete complete all as specified and directed

M&L for form work to edges of concrete flats, treads, breaks in floors window cill, concrete railing opening in conc wall , floor and roof n.exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n.exc 20cm wide for rough finished surfaces of concrete, complete all as specified and directed.

Supply and fixing TMT bars, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) but not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M&L for PCC (1:2:4) type B-0 using 10/12.5 mm graded stone aggregrate laid over roof slab after applying cement slurry for filling undulationations finished even and smooth without using extra cement complete all as specified and directed.

M & L for applying cement slurry over existing roof surface @ 3 Kg/Sqm incl mix with water proofing liquid @ 0.20 ltr per 50 kg cement bags as per manufactures instructions complete all as specified and directed. (Note : Water proofing liquid shall be measured and paid separately)

M&L screed bed or bedding layer of mortar, 15 mm thick, in cement mortar (1:4), over RCC roof slabs for laying water proofing treatment mixed with using water proofing liquid @ 200 ml per bag of cement complete all as specified and directed. (Note : Water proofing liquid shall be measured and paid separately)

Supply only liquid water proofing compound (ISI) marked complete all as specified and directed.

M & L for cool roof antislip tiles 300x300x10 mm with high SRI value not less than 90 laid over existing treatment on accessible roof and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) complete all as specified and directed.

M&L for brick work with old size burnt clay bricks, built in CM (1:4) in half brick thick walls complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:6 on other than fair faces of brick/masonry wall surfaces finished even and fair without using extra cement complete all as specified and directed.

M & L for 15 mm thick rendering in two layers on fair faces of brick work or concrete surfaces first layer of 10 mm thick in CM (1:6) and second layer of 5 mm thick in CM (1:4) with mixing of water proofing compound @200 ml / bag of cement complete all as specified and directed. Note:- Water Proofing liquid shall be measured and paid seprately.

M&L for rendering 5 mm thick in CM 1:3 as on concerete surface of ceilings finished even and smooth without using extra cement complete all as specified and directed.

S & F 125 x 50 mm size Factory made single extruded WPC(Wood polymer composite) solid door/window/ceosetory windows and other frames/chowkhat of size 45*70mm comprising of virgin PVC polymer of K value 58-60(suspension grade),calcium carbonate and natural fibres(wood powder/rice husk/wheat husk) and non toxic additives(max toxicity index of 12 for 100gms)fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum,screw withdrawl strength of 2200N(Face) and 1100 N(Edge),minimum compressive strength of 58N/mm2,modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof,water/moisture proof and fire retardant and fixed in positin with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engg-in-charge(M.S hold fast/lugs or SS dash fasteners shall be paid for separately) Note:For WPC solid door/window frames, minus 5 mm tolerance in dimension i.e depth and width of profile shall be acceptable.Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

S&F factory made single extruded WPC(Wood polymer composite) solid decorative type plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60(Suspension grade),calcium carbonate and natural fibres(wood powder/rice husk/wheat husk)and non toxic additives (maximum toxicity index of 12 for 100gms)having minimum density of 650 kg/cum and screw withdrawl strength of 1800N(Face) and 900N(Edge),minimum compressive strength 50 N/mm2,modulus of elasticity 850 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof,water/moisture proof and fire retardant and fixing with stainless steel butt hinge of required size with necessary full body threaded star headed counter sunk S.S screws,all as per direction of Engg-in-charge. (Note-stainless steel butt hinges and necessary SS screws shall be paid separately)

S&F 35mm thick WPC(Wood Polymer Composite) factory made glazed and skeleton door shutters decorative type open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain cham-fered or rounded, mitred and rebated sash bars, any numbers The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. (Note :- Supply only of Glass/gauge shall be measured and paid for separately)

M&L for Preparation of wood and wooden surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed..

S&F stainless steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staples complete all as specified and directed.

S & F 150 mm long floor door stopper of brass body and tongue with hard drawn steel spring, fixed in floor complete all as specified and directed.

S & F 150 mm thick Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S & F 200 mm thick Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150mm thick Stainless steel handles, cast type anodised complete all as specified and directed.

S&F 100 mm size mild steel butt hinges medium weight mild steel colled rolled complete all as specified and directed.

S&F 300 mm size ordinary mild steel , rat tailed rod pattern spring including roller and roller plate welded to mild steel frame fixed in repair complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet,cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame., complete as specified by the manufacturer and as per directions of Engineer-in-charge

Supply and fixing 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table 3 of IS: 14856 complete all as specified by the manufacturer and as per directions of Engineer- in-charge.

S&F mild steel window grills box type framed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding confirming to FE-290 grade E-165 complete all as specified and directed.

S&F steel window with pressed steel frame(size 95*45*1.25mm)side hung shutter including box type hinges with steel handle and steel peg stay complete with glaed openable shutter with glazing bar(open outside) and wire gauged openable shutter without glazing bar(open inside),detailed or welded complete all as specified and directed and as per Drg no TD-88 sh 1/2 and 2/2. (i)Two shutter i.e wire gauged and glaed shall be fixed in one composite frame and both shutter shall be measured as one unit. (ii)rate for filling of PCC frame deemed to be included in quoted rate. (iii)MS grill,wire gauge and glass shall be measured and paid separately.

S&F for steel windows/ventilators with top hung shutter including hinges,steel peg stay complete with glazing bars complete welded including one shop coat of red oxide zinc chromate primer complete all as specified and directed. (Note:-Glass shall be measured and paid separately)

Providing and fixing factory made UPVG white colour sliding window three track of area exceeding 2.00 Sqm each made of extruded profiles with wall thickness 2.3 mm (+/-0.2 mm). Window profile with hollow section with multi chamber. Frame (88mm X 52mm), sliding sash (42mm X 67mm). Sliding mesh Sash (42mm X 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm) , Glazing bead (24.5 mm x 16 mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, (1.2 +/- 0.2) mm thick galvanised steel Frame (30 mm X 18mm) 2 Nos, sliding sash (30mm x 18mm), sliding mesh sash (26mmX10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware (Touch Lock of Zinc alloyed(white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor exculdes cost of glass and includes all other connected acessories. Net Opening will be measured for payment purpose.

S & F for aluminium powder coated frame hollow sections members of size 63.50 mm x38mmx 1.48 mm thick fixed with 3 mm thick aluminium composite panel into the wall for kitchen cabinet/ cupboard shelf incl hanging self for clothes with aluminium clip/strips, PVC beadings fixed with adhesive on edging , design as per site requirements basis, complete all as specified and directed.

S&F for Stainless Steel (AISI 304 grade ) non magnetic multilayer nickel chrome plated for multipurpose utensils container including frame work , telescopic channels , handles etc as reqd & complete all as specified and as directed, utensils sample , design & pattern of each basket to be approved by GE of following size in each kitchen :- (a) plain basket of size 510x470x100mm or 520x485x100 mm or 486X500X100mm -01Nos size 530x505x150mm/ (b) multi size plate basket of size 510x470x150mm or 520x485x150 mm or 436 x 500 x200 mm (clear depth 500 mm) -01 Nos. size 530x505x100)mm size 520x485x90mm (c) cutlery basket,with perforated bottom & side of compacted /slots for holding cutlery of size 510x470x100mm or 520x485x100 mm or 144x 468 x50mm ( clear depth 500 mm) -01Nos , size 530x505x100 mm/ 520x485x95mm (d) Plain basket of size 510x470x200mm or 520x485x200 mm or 486x500x200 mm -02 Nos, size 520x485x180 mm. (e) Pull out with 02 baskets each of size 150x485x80mm or 100x485x80 mm -01 Nos 610x485x90 mm. (f) Dust bin as required -01 Nos Make:- 200 series of Hettich order No 9210444)/Sleek Elnora (Asian Paint) elnora grade SS 304/Evershine size 250x 145 mm. (g) Telescopic channels, handels etc as required complete all as specified and as directed. as reqd incl frame work handles etc as reqd & all as spd, sample & design as approved by GE. Note:- Sample and design to be approved by GE.

S&F ball catches with 8mm dia steel ball and brass body and striking plate including letting in and fixed, complete all as specified and directed.

S&F 200 mm long Stainless Steel glossy finish handles with SS screw, complete all as specified and directed.

S& F factory made single extruded WPC(wood polymer composite)solid door/window/ceosetory windows and other frames/chowkhat of size 40*70mm comprising of virgin PVC polymer of K value 58-60(suspension grade),calcium carbonate and natural fibres(wood powder/rice husk) and non toxic additives(max toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum screw withdrawl strength of 2200 N(Face) and 1100 N(Edge) min compressive strength of 58 N/mm2 modulus of elsticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per dir of engineer-in charge(M.S hold fast/lugs or SS dash fasteners shall be paid for separately)

S&F factory made single extruded WPC(wood polymer composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60(suspension grade) calcium carbonate and natural fibres(wood powder/rice husk)and non toxic additives(max toxicity index of 12 for 100 gms)having min density of 650 kg/cum and screw withdrawl strength of 1800 N(Face) and 900 N(Edge) min compressive strength of 50N/mm2 modulus of elsticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws all as per dir of Eng-in charge

S&F for factory made 18 mm thick WPC solid board of density 600 Kg/cum as in cupboard shelves, partitions, sides of cupboard & drawers with collapsible handle & with wardrobe/ finch lock, including powder coated aluminium cleat of size 25X25X3mm(colour of powder coated to match colour / shade of laminate) and as in fixing to sides of cupboard, soffits & base of cupboard with SS fastener, also including PVC lipping on all exposed edges of same texture & shade to match the laminate complete all as specified as directed. Note: 1) Design & layout of wardrobe and pattern / colour of lamination to be approved by GE.

S & F 125 mm aluminium hasp and staple including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F rotational moulded polythene water storage tank Triple Layer white colour Cylindrical vertical with closed top)hoisted and fixed in position of 1000 ltrs capacity fixed with PVC tank nipples,complete all as specified and directed Incl dismantling of existing tank.

S&F rotational moulded polyethylene water storage tank Triple Layer white colour (Cylindrical vertical withclosed top)hoisted and fixed in position of 500 ltrs capacity fixed with PVC tank nipples, complete all as specified and directed Incl dismantling of existing tank.

S&F 20mm bore ball brass valve high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F,16 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Refixing old steel tubing and connection in new or old position (wall, Ceiling,Floor, etc.) 15mm bore complete all as specified and directed.

S&F,20 mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Refixing old steel tubing and connection in new or old position (wall, Ceiling,Floor, etc.) 20mm bore complete all as specified and directed.

S&F in repairs vitreous chinaware wash hand basin with pedestal of size 55X45X82cm complete including 15mm dia CP pillar tap fancy type, CP brass waste coupling, waste pipe, 450 mm long HDPE PVC connection including fixing arrangement and cutting for and pinning in walls & making good complete all as specifed and directed.

S&F in Vitreous China table top wash basin of size 455cm x 325cm x 135 cm including SS bottle trap, HDPE waste pipe including fixing on counter with SS waste coupling complete all as specified and as directed.

S&F in repairs brass chromium plated wall single lever diverter concealed body 3 in 1, 15mm for mixing hot & cold water screwed down three joints to steel pipes or unions and plugging and screwed to walls complete all as specified and as directed.

S&F Brass chromium plated wall mixer 2 in 1 , 15mm for mixing hot & cold water, screwed down three joints to steel pipes or unions and plugging and screwed to walls complete all as specified and directed.

S&F in repair fancy type 15mm dia chromium plated fancy type Sink mixer hot & cold with long swan for kitchen sink fixing and connection to pipes complete all as specified and directed.

S&F in repair brass chromium plated toilet paper holder, complete all as specified and directed.

S & F in repair fancy type 125mm size square brass CP shower rose complete all as specified and directed.

S&F in repairs 15 mm dia bib tap fancy type chromium plated with flange quarter turn complete all as specified as directed.

S&F in repair fancy type 15mm dia brass chromium plated mixer for mixing hot and cold water screwed down for iron pipe and fixed to WHB including taking out existing mixer from old WHB, complete all as specified and directed.

S&F in repair fancy type chromium plated brass two way bib cock suitable for 15mm bore pipe 2 Way Bib Cock with Wall Flange complete all as specified and directed.

S&F stainless steel of AE - SI 316 grade tubular towel ring including a pair of CP brass bracket complete all as specified and directed.

S&F in repairs 15mm bore PVC connections, with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair fancy type brass chromium plated soap dish of 160x160x90 mm, complete all as specified and directed..

S&F (in repairs) angle cock cast copper alloy chromium plated fancy type screw down ,screwed both end for iron pipe or or brass ferrule for 15 mm bpre of pipe complete all as specified and as directed.

S&F in repair fancy type stainless steel towel rack size 600mm X 300mm including a pair of brass bracket complete all as specified and directed.

S&F in repair chromium plated brass tubular towel rail 20 mm dia, D type for wash hand basin centre holed fixed to iron pipe complete all as specified and directed.

S&F for fancy type glass corner 300mm radius of 10mm thick toughned glass with CP railing fixed with screws fancy type complete all as specified and directed.

S&F in repair 15 mm dia fancy type stop cock , chromium plated with long shank and cup (concealed type) for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair vitreous china squatting pan of orrissa pattern long pan size 580 x 440 mm white with "P"or "S" trap size 100 mm dia front or back inlet and integral foot rest any pattern (excluding flushing cistern and flush pipe) including provn of lime concrete bedding complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) with 'P' or 'S' trap white, including connection to drain or out going pipe and flush pipe anti symphonize pipes etc complete all as specified and directed.

S&F in repairs, PVC low level flushing cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket etc complete all as specified and directed.

S & F in repair Brass CP health faucet with 8mm Dia 1.25 Meter Long Flexible Tube and Wall Hook screwed for iron pipe fancy type long body complete all as specified and directed.

S & F Brass CP Hand Shower with 8mm Dia 1.2 Meter Long Flexible Tube and Wall Hook screwed for iron pipe fancy type long body complete all as specified and directed.

S&F in repair PVC (SWR) multifloor trap with grating including jointing with solvent cement floor trap 75 mm dia outlet plain with grating including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 complete all as specified and directed.

S&F in repair PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fitting complete all as specified and directed.

S&F in repair PVC (SWR) 110mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fitting complete all as specified and directed.

S&F PVC (SWR) 110mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75 mm bore junction single (Single 'T') equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) 110 mm bore junction single (Single 'T') equal or unequal with access door complete all as specified and directed.

S& F Mortice lock 4 lever , size 75mm as all specified and directed

S&F in Stainless Steel plate rack of size 90x80x25cm made with 1.00 mm thick sheet including taking out existing wooden plate rack, complete all as specified and directed.

S&F in repair for 0.8 mm thick stainless steel kitchen sink size 590x460x230mm undermount, single bowl (bowl size 540x410x230 mm) , incl waste pipe & SS coupling, washers etc complete all as specified and as directed.

S & F in repair for 0.8 mm thick stainless steel in graceful glory range ,anti scratch, satin finish of popular range kitchen sink over all size 990x459mm , double bowl size 400x340xx200 mm incl waste pipe & SS coupling, washers etc. complete all necessary fittings all as specified and as directed.

S&F in repair 25 mm dia stainless steel 1.0 mm thick fancy type drapery rod with decorative design matching brackets as approved and knobs (lattu) or end bracket as required incl fitting with 80 mm long SS screw with 75 mm long wooden gitty of appropriate c/s in each end & intermediate support complete all as specified and directed.

M&L for Providing & injecting chemical for post construction ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in a portion with cement mortar 1:2 to match the existing apron complete all as specified and directed.

M & L for Post Construction anti termite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor soil complete all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1979 complete all as specified and directed.

S&F Pre-coated Mangalore pattern galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

M & L for cutting chases of hanging chajjas, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of sunshades, shelves, lintels, Chajja ( up to IInd floor) etc making good, cutting out exc 10cm and not exc 40cm girth in RCC chajjas in brick walls complete all as specified and directed.

Dismantling of concrete by chiseling from RCC members like column , beam, parapet facia, chajja, ceiling,etc exposing the reinforcement without disturbing the reinforcement free from rust by sand blasting/using chemical , apply a coat of rustolin to remove rust and acralic polymer on old rusted reinforcement proving at places addl reinforcement welding with existing reinforcement as directed wherever required binding RCC 50 mmx50 mm (10 mm gauge welded mesh ) & tack , securing with clips / blinding wire, welding & provision guniting pressure 2.2 to 2.5 kg /sqm with admixer 1 part cement and 3.5 part of sand of thickness 25 to 40 mm including stripping floating with wooden strippers for proper dimension control neccssary form work & scaffolding up to three storey and including height of head room complete surface of guniting to be finished fair with 10 mm thick plaster in cement mortar 1:4 with water proofing compound @3% by weight of cement and recron 3 S as per manufacturer instruction cleaning & removing of waste meterial etc as dirply two coat of Dr fixit /pidilite new coat ezee at interval of 8 hours cure for the surfaces complete all as specified and directed.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and fastening and fixing FE 290 Gde E-165 complete all as specified and directed.

S & F 1.60 mm thick Mild steel, plain black sheet in steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles etc as required complete including cutting out of existing sheet if required complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed.

M& L for two coat of oil bound distemper incl preparation of old treated surface of wall including 1 mm thick wall care putty with airless electric sprayers prepared and sanded with electrically operated machine complete all as specified and as directed.

M& L for two coat of oil bound distemper including preparation of new surface of wall including 1 mm thick wall care putty with airless electric sprayers prepared and sanded complete all as specified and as directed.

M&L for for complete removal of existing treatment and applying of two coat OBD on ceiling including complete removal of old finishes and preparation of surface with airless electric sprayers prepared and sanded complete all as specified and directed .

M&L for preparing newly plastered surfaces and applying two coat OBD on ceiling including preparation of surface with airless electric sprayers prepared and sanded complete all as specified and directed .

M&L for complete removal of existing treatment, preparation of old decorated plastered or unplastered surfaces of walls and applying two coat of white putty and applying one coat of exterior water based primer by using Airless spray techonology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressue and paint usage and certified by jpaint manufacturer and as mentioned in PS and accessories fpr applying distemper, should be able to spray in hard to reach areas and penetration of distemper, on the surface to achieve excllent application using limited manpower complete all as specified and directed. Note : - Sanding of old decorated surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer.

M&L for applying two coat of exterior weather proof 100% anti fungal acrylic smooth emulsion with silicon additives that offer anti alge high performance exterior wall finish with 6 years of performance warranty by manufacturer applied by using Airless spray technology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacture with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper, should be able to spray in hard to reach areas and penetration of distemper on the surface to achieve excellent application using limited manpower complete all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of walls and applying two coat of white putty and applying one coat of exterior water based primer by using Airless spray techonology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressue and paint usage and certified by jpaint manufacturer and as mentioned in PS and accessories fpr applying distemper, should be able to spray in hard to reach areas and penetration of distemper, on the surface to achieve excllent application using limited manpower complete all as specified and directed. Note : - Sanding of old decorated surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer.

M&L for applying two coat of exterior weather proof 100% anti fungal acrylic smooth emulsion with silicon additives on new plastered surfaces that offer anti alge high performance exterior wall finish with 6 years of performance warranty by manufacturer applied by using Airless spray technology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacture with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper, should be able to spray in hard to reach areas and penetration of distemper on the surface to achieve excellent application using limited manpower complete all as specified and directed.

S&F in repair 20mm dia gun metal ,globe or gate valves , with iron wheel head , screwed both ends for iron pipe complete all as specified and directed.

M&L for reinforced cement concrete(1:2:4) type B1 using 12.5mm graded stone aggregate as in chajjas complete all as specified and directed.

S&F in repairs gun metal globe or gate valve with iron wheel screwed both ends for iron pipe of 15 mm dia complete all as specified and directed.

Demolition an breaking up drain pipes(salt glazed ware,AC or Reinforced concrete)of size 100mm set in cement mortar

M&L for RCC pipe class NP2 laid and jointed complete with collar 150mm bore completed all as specified.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 complete and finished surface even and smooth without using extra cement.

M&L for providing cement concrete type B0 1:2:4(12.5 mm graded aggregate) in lintels upto 1.5m clear span,cills,steps:seismic and other similar bands,plinth courses,string courses,lacing courses,parapets and railings upto 60 cm in height,coping,knnelers,apex stones,bed plates,kerbs water troughs and the like including weathering,slightly rounded or chamfered angles and throating,as directed

M&L for concrete bed to drain pipe including packing under and haunching around the side of pipe after they are laid and tested in for 150mm bore pipe in cement conc 1:4:8 type D2 using 40mm graded stone aggregate complete all as specified and directed.

M&L cutting chase for pipes pinning in making good to fancing where required in cement mortar in CM 1:3 and making surface good cutting out not exc 10 cm in girth in RCC/ brick wall complete all as specified and directed.

M&L looking mirror 5mm thick of size 300mm x 900mm fixed to wooden surface with wooden frame of size 30mm x 20mm section complete all as specified and directed.

M&L silicon ceiling strip for door bottom self-adhesive and fixed with screw of size 4.8 cm and 0.3mm thick of any colour all as specified and directed.

M&L stainless steel railing of FE304 of any size and shape fixed to concrete/ brick stone/ tiles with steel rawl plug nut and bolts complete all as specified and directed.

M&L forming square grooves in plaster not exc 12mm deep and not exc. 15mm on face and filled with polysulphide compound or equivalent water proof elastic compound all as specified and directed.

M&L PVC green fibre sheet 4mm thick of any colour fixed to angle iron frame with nuts and bolts complete all as specified and directed.

E/M Items:

S&F Sheet metal enclosure TPN distribution board vertical type double door with insulated bus bar arrangement IP 43 protection 4 way 415V complete all as specified .

Taking down of TPN DB all as specified.

S&F MCCB TPN 100 Amps 16 KA all as specified

S&F MCCB TPN 63 Amps 16 KA all as specified

Taking down faulty damaged unserviceable LT under ground cable of any size.

Supply and laying XLPE insulated, armoured, heavy duty electric cable with aluminium conductor, 1100V grade, cross-sectional area 16 sqmm 4 core complete all as specified .

Supply and laying XLPE insulated, armoured, heavy duty electric cable with aluminium conductor, 1100V grade, cross-sectional area 25 sqmm 4 core complete all as specified .

Supplying and laying un-reinforced precastconcrete cable cover, but Class LV, Type I, flat, size 250mm x 150mm x 40mm all as directed and specified by Engr-in-Charge.

Taking down carefully of point wiring (Light , fan, socket or power) complete (fittings such as switches, Ceiling roses, pendants, regulator, sockets etc to be measured separately) removing from site of work and making good to the disturbed surfaces of walls/floors etc all as directed

Taking down carefully old unserviceable fittings & Fixers of any type and any size.

Taking down carefully old unserviceable by unscrewing from DB box, MCB SP/SPN/TPN of any size & any capacity .

Taking down carefully old unserviceable sub main wiring of any size .

Concealed Point wiring using approved colour coding as per IS in concealed PVC conduit using stranded copper conductor cable of size 1.5 Sqmm, PVC insulated unsheathed FRLSH cable complete with all fittings and accessories sunken cast iron or pressed steel terminal box for mounting of switches, sockets, fan regulators etc but with 2 module to 18 module modular base and sheet fastened with chromium plated screws and 1.5 Sqmm PVC insulated stranded copper conductor FRLSH cable as continues earth wire connected to common earth dolly all as directed and as specified for the following :- NOTE: (i) Cutting /chasing of wall etc. deemed to be incl in quoted rate item.(ii) Modular GI metl flush/sunken box along with modular base/front cover are inclusive in the item rate quotd.(iii) Only switches sockets and fan regulator shall be measured and paid seperetly.

(a). One light point controlled by one switch

(b). One fan point controlled by one switch

(c). One exhaust fan point controlled by one switch

(d). One 3-pin socket outlet 5 Amp on independent board.

(e). One 3 pin socket outlet 5 Amp on same board

(d). One light point controlled by two way switches

(f). One bell point controlled by one switch

All per Srl item No. here-in-before, but with 2.5 Sqmm copper conductor cable complete all as specified for One 3 pin socket outlet 15 Amp on independent board.

Material and labour for two single core PVC Insulated unsheathed multi stranded FRLSH copper conductor cable of size 6sqmm as sub main wiring including suitable size heavy duty rigid PVC conduit and of PVC insulated unsheathed multi stranded FRLSH copper conductor cable of size 6 sqmm as an earth continuity conductor complete all as specified. Note : Two run of 6.00 sqmm copper cable, one run of 6.00 sqmm copper cable and one run of conduit shall be measured as one unit.

Material and labour for two single core PVC Insulated unsheathed multi stranded FRLSH copper conductor cable of size 10 sqmm as sub main wiring including suitable size heavy duty rigid PVC conduit and of PVC insulated unsheathed multi stranded FRLSH copper conductor cable of size10 sqmm as an earth continuity conductor complete all as specified. Note : Two run of 6.00 sqmm copper cable, one run of 6.00 sqmm copper cable and one run of conduit shall be measured as one unit.

Material and labour for two single core PVC Insulated unsheathed multi stranded FRLS copper conductor cable of size 4 sqmm as sub main wiring including suitable size heavy duty rigid PVC conduit and of PVC insulated unsheathed multi stranded FRLS copper conductor cable of size 4 sqmm as an earth continuity conductor complete all as specified. Note : Two run of 6.00 sqmm copper cable, one run of 6.00 sqmm copper cable and one run of conduit shall be measured as one unit.

S &F Modular switch polycarbonate SP one way 6 Amps complete all as specified and directed

Supply and fix in replacement two way modular switch 6 amps, 230 volts, complete all as specified .

S &F modular switch type polycarbonate SP one way 16 Amps complete all as specified .

S&F bell push modular type 6 amp single pole one way complete.

S&F modular socket out let 3 pin 6 amp multipurpose flash type.

S&F modular socket out let 5 pin 6/16 Amp multipurpose, flush type 240 volt complete.

S&F ceiling rose surface Bakelite 65 x 50 mm two to three terminals complete.

S&F bell ding dong type AC 230 volt single pole Complete.

S & F lamp holder insulated body surface bakelite with back plate suitable for angle / batten fittings fixed with wooden round blocks all as specified.

Supply and fixing LED bulb 9 watt include connection all as specified. Make: C &S

M & L replacement of 0 to 5 step fan regulator suitable for BLDC fan on modular box sheet as required complete all as specified and directed.

Taking down Exhaust fan of any size and deposited to E/M storeyard for refixing, complete all as specified

Taking down fan of any size, sealing cable end, dismantling blades and removing fan and blades to store.

M&L exhaust fan PVC body single phase 230 V of size 250mm sweep with blade and frame with louvers complete all as specified and directed.

Supply and fixing 240V, 10 KA 'B' curve miniaturecircuit breaker (MCB) of single poles and currentcarrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and as directed by Engr-In-Charge.

Supply and fixing 240V, 10 KA 'B' curve miniaturecircuit breaker (MCB) of single poles and currentcarrying capacity SPN 40 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and as directed by Engr-In-Charge.

Supply and fix in replacement MCB DB Single pole and neutral 8 way sheet steel phospetised powder painted with 200 amps rated bus bar with IP 43 protection 240 V nautral link, earth bar and Din rail double door complete all as specified and as direcrted .

Supply and fix in replacement MCB DB Single pole and neutral 4 way sheet steel phospetised powder painted with 200 amps rated bus bar with IP 43 protection 240 V nautral link, earth bar and Din rail double door complete all as specified and as direcrted .

Taking down and refixing the same of Decorative box type LED light fitting suitable for 4 ft T8 -20 watt with blue colored end 20 watt complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size all as specified and as directed.

S&F Decorative box type LED light fitting suitable for 4 ft T8 -20 watt with blue colored end 20 watt complete with all accessories pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size all as specified and as directed.

Taking down old unsv bldg security light fitting, Supply and fixing new LED bldg security light fitting 35 watts to be fixed to channel and as reqd to be mounting bracket in wall/floor to suit the opening of the fitting with FI clamp, nut, bolt and washers of suitable size including making connection complete all as specified.

Material and labour for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick, buried directly in ground, vertically to a depth not less than 2.25 mtr deep below ground level with top edge of the earth plate at depth not less than 1.5 mtr below ground level earth plate surrounded by 15 cm thick and packed layers of charcoal, dust and common salt, earth lead GI wire 4mm dia by means of bolts, nuts, check-nuts and washers of galvanized iron and thimbles and of earth wire protected by galvanized iron pipe light grade 15mm bore and water pipe 20 mm bore GI medium grade with funnel and wire mesh complete including excavation and earth work, PCC chamber and cover in cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate in lieu of CI cover and frame etc all as specified and shown in electrical plate No. 5 of SSR-2009 (Part-I including testing after completion.

Supply and fixing Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20Amp complete all as specified and as direcrted.

Supply and fix decorative light fitting 1x9watt ceiling/wall mounted LED BULKHEAD luminaire with engineering plastic housing and top frame with opal PMMA diffuser.

S&F "BLDC" ceiling fan 1200mm sweep 230V BEE5 star rated complete all as specified and directed.

Taking down existing energy meter by disconnecting clectric connection of any type ,any make ,any capacity in poly carbinate or sheet steel body, ISI marked ,50 Hz 240 volts AC single phase rating etc. all as specified.

Refixing existing energy meter by disconnecting clectric connection of any type ,any make ,any capacity in poly carbinate or sheet steel body, ISI marked ,50 Hz 240 volts AC single phase rating etc. all as specified.

S & F in replacement mirror LED light fitting 2 feet 10 watt with accessories complete all as specified and directed.

Supply and fix electric water heater,storage type steel body with copperinner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Starrated complete with all accessoriessuch as safety valve, thermostate,NRV, connection piece etc all as specified.

S & F PVC conduit with accessories 25 mm dia for drawing telephone/TV/internet wires complete all as specified and directed. Note :- ( only PVC conduit with accessories shall be measured and paid).

S & F for TV socket and including sunk cast iron 1.6 mm thick pressed steel terminal box and mounting of hylem sheet its necessary fittings and accessories all as specified.

Common Items:-

Excavation in trenches n.exc 1.5m deep & n.exc 1.5m wide and n. exc 10 sqm on plan, in soft/loose soil and getting out.

Returning filling in including spreading leveling, watering and well ramming in layers not exc 25 cm in soft/loose soil.

Removing excavated soil material n. exc. 50 mtr and depositing where directed at a level n. exc. 1.5 mtr above the starting point complete all as specified and directed.

M&L for Sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

Note: The amount of Rs. 5,82,087.00.00 shall be deducted from the quoted amount.

M/S SURAT SINGH AND SONS (BID ID -3399614)

BHARAT ELECTRICAL TRADERS (BID ID -3395226)

A K BANDHUS (BID ID -3394054)

HI TECH COLONISERS PRIVATE LIMITED (BID ID -3394107)

Ms dev associates (BID ID -3393344)