REP/REPLACMENT CLEANING OF SEWAGE LINES, SEPTIC TANKS, MANHOLES, SOAK WELL, ETC OUTSIDE MH, REP/MAINT OF CENTRIFUGAL/ SUBMERSIBLE PUMP SET AND CONNECTED WKS OF WATER SUP AND STREET LIGHT, CONNECTED ITEM OF WKS AT NAMKUM AND KHOJATOLI UNDER GE RANCHI

Amount

Excavation in trenches n.exc 1.5 metres wide and n.exc 1.5 metres deep for foundation etc for shafts, cesspits, manholes etc n.exc 10 Sqm on plan and n. exc 1.5 metres in depth and getting out in hard/dense soil.

Demolition and breaking of SGSW or RCC drain/Soil pipes jointed in cement mortar and taking out from trenches if required internal diameter 150mm.

Demolition of brick work built in cement mortar.

Demolition of reinforced cement concrete of any description in any position not otherwise described, complete all as specified and directed.

Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level).

Taking down cement plaster on wall of any description incl racking out joints hacking for key and scrubbing down with water, complete all as specified and directed.

Returning filling in incl spreading leveling watering, well ramming in layers not etc 25 cm hard/dense soil

Removing excavated materials etc not exc 50 metres depositing where directed at a level of n.exc. 1.5 metres above the starting point.

M&L pre cast RCC (1:1.5:3) type A-1 as in manhole cover, drain cover and set in cement mortar (1:4) including necessary formwork, complete all as specified and directed.

M&L brick work with sub class 'B' brick straight or curved on plan exc 6 metres radius with old size bricks built in cement mortar (1:4), complete all as specified and directed.

M&L PCC 1:3:6 and type C-2 using 40mm graded stone agregate for concrete bed to drain pipes including packing under hunching against the sides of pipes after they laid and tested for 150mm dia pipes, complete all as specified and directed.

M&L cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate in fondation and mass concrete for manhole surface channels and drains, complete all as specified and directed.

M&L Salt-glazed stone ware drain (SWSG) pipe grade 'A' 150 mm dia laid in trenches & jointed in CM 1:1 and tested, complete all as specified and directed.

M&L PCC (1:2:4) type B-1 using 20mm graded stone aggregate in coping etc, including weathering slightly rounded champers angle forming channels & form work.

M&L PCC (1:2:4) type B-1 using 20mm graded stone aggregate as benching including forming channels using forms, moulds etc, complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 using 20mm graded stone aggregate including finished surface even & fair without using extra cement as in plinth protection including necessary form work of edge all as specified and directed. Note: 10mm wide and 75mm deep joints shall be made at 3 mtr intervel and at each corner and the same shall be filled with using bitumen 85/25 and sand in the ratio 1:3, complete all as specified and directed.

M&L mild steel TMT bar 8mm dia cut to length bent to shape required including cranking bending and binding with MS wire not less than 0.9mm diaor securing clips, complete all as specified and directed.

M&L rendering 15mm thick cement mortar (1:4) on fair faces of brick or concrete surfaces and finished even and fair without using extra cement, complete all as specified and directed.

Cutting into existing manholes for connecting new drains making good to pipes and rendering, cutting existing benching for forming branch channel etc for 150mm pipes, complete all as specified and directed.

Cleaning and dewatering of Septic tank by any means & getting out and removing the sludge to a distance not exc 250m and disposal of the same in approved low lying areas complete all as specified and directed. Capacity of tank 50 users.

All as per item No 20 above but of capacity 100 users.

All as per item No 20 above but of capacity 150 users.

All as per item No 20 above but of capacity 200 users.

All as per item No 20 above but of capacity 500 users.

Dewatering of soak well/Soak pit by pumping out and discharging the water away using suitable discharge, digging katcha channel for flow of water and making good of the same, complete all as specified and directed. Dia (internal) exc 1.2m and n exc 1.8m and depth up to 3m.

All as per serial item No. 25 above but dia (Internal diameter) exc 1.2m and n exc 1.8m and depth exc 3m and n exc 4.50m.

All as per item No. 25 above but dia (Internal diameter) exc 1.8m and n exc 2.40m and depth exc 3m and n exc 4.50m.

S&F in repairs 110mm dia, PVC (SWR) Pipes single socketed in any length with rubber rings joints land in trenches or floor and making good the surfacecomplete all as specified and directed.

S&F in repairs 110mm dia, PVC (SWR) Pipes single socketed in any length with rubber rings joints fixed to walls, complete all as specified and directed.

S&F in repairs 75mm dia, PVC (SWR) Pipes single socketed in any length with rubber rings joints fixed to walls, complete all as specified and directed.

S&F PVC (SWR) vent cowl, 110 mm dia.

S&F PVC (SWR) bend, 110 mm dia.

S&F PVC (SWR) junction single, (Single T) equal or unequal 110mm dia, complete all as specified and directed.

S&F PVC (SWR) bend, 75 mm dia.

S&F PVC (SWR) junction single, (Single T) equal or unequal 75mm dia.

M&L forming fair finished drain or channel, 30 cm inner girth, cement concrete finished even and smooth, using extra cement including forms moulds etc, complete all as specified and directed.

Cleaning of blockage of WCs , bath room and blockage sewage line, manhole etc. day to day wise as per complain slip received from concerned AGE B/R-II located at Namkum cell on all working day from 900 hrs to 1700 hrs doing only by manually (including all necessary T&P), complete all as specified and directed.

S&F in repair vitreous china squatting pan, Orrissa pattern size 580x440mm white with PVC 'P' or 'S' trap with integral foot rest of any pattern incl connection to trap & to flushing pipe, antisyphonage pipe etc making good to floor, complete all as specified and directed.

S&F in repair Vitreous china wash down water closet pan ( pedestal pattern), white (excluding fixing bolt, flushing cistern and flush pipe) but including P or S trap, sheet cover of white colour, complete all as specified and directed.

S&F in repair vitreous china wash hand basin, white, flat back, size 550x400 mm incl chain and plug and porcelain stopper, brackets, waste pipe incl cutting for and pinning in ends of brackets or erecting stand including dismantling, complete all as specified and directed.

S&F in repair PVC flushing cistern 10 ltr capacity including bracket fixed to wall & flush pipe complete ISI marked, complete all as specified and directed.

S&F in repair, plastic water closet seat cover, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device for pedestal pattern WC, black/ white colour, complete all as specified and directed.

Taking up or steel tubing & connections including cleaning for refixing bore of pipe 15mm etc, complete all as specified and directed.

All as per item No 43 above but 20mm bore.

S&F tubes medium grade galvanised with all fittings & fixed complete to walls & ceiling or laid in floors 15mm bore etc, complete all as specified and directed.

All as per item No 45 above but 20mm bore.

Refixing old galvanised steel tubes & connections on wall 15 mm bore complete all as specified and directed.

All as per item No 47 above but 20mm bore.

S&F in repair for Gun-metal, globe or gate valves 20mm, with iron wheel head, screwed both ends for iron pipe etc, complete all as specified and directed.

S&F in repair for Gun-metal, globe or gate valves 15mm, with iron wheel head, screwed both ends for iron pipe etc, complete all as specified and directed.

S&F in repair bib tap 15mm fancy type of PTMT any colour high pressure screwed for iron pipe and fixed, complete all as specified and directed.

S&F in repair bib tap 15mm chromium plated fancy type long shank with crutch butterfly handle, screw down screwed for iron pipe or for brass ferrule etc, complete all as specified and directed.

S&F in repair stop valve 15mm chromium plated screw down, high pressure with crutch or butterfly handle, screwed fboth ends for or iron pipe or for unions and fixed, complete all as specified and directed

All as per item No 53 above but two way angle cock.

S&F in repairs IVC hand shower (Health faucet) with 8mm dia, 01 (one) metre long PVC tube and wall hook with plastic body, complete all as specified & directed.

S&F in repairs 15mm dia pillar tap cast copper alloy fancy type with capstan heads chromium plated screwed down high pressure with or without letered "Hot or Cold" high pressure with long screwed shanks & fly nuts screwed for iron pipe etc, complete all as specified and directed.

S&F in repairs 15 mm dia concealed type stop valve fancy type chromium plated etc, complete all as specified and directed.

S&F in repair Brass chromium plated shower rose 125mm size fancy type with or without swelves joint fixed to iron pipe etc, complete all as specified and directed.

S&F in repair PVC connection 450mm long with two PTMT nuts (Prayag).

S&F in repair CP towel rail, 20mm dia, D type,60cm long, complete all as specified and directed.

S&F in repair 32mm bore waste coupling of PTMT (half or full threaded) (Min wt 45 gms), complete all as specified and directed.

S&F in repair 32mm bore low density polyethylene (LDPE) pipes of pressure rating 6 Kgf/Sqcm, complete all as specified and directed.

M&L 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified and directed.

M&L dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), complete all as specified and directed.

M&L Cement concrete 1:5:10, type E-2 (using 40 mm graded stone aggregate) as in sub base etc, complete all as specified and directed.

M&L Cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in levelling course, coping, etc, complete all as specified and directed.

M&L for joint free non skid coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc incl 15mm thick screed bed in CM 1:4, set & jointed in neat cement slurry and pointed with white or coloured cement to match, complete all as specified and directed.

M&L coloured ceramic glazed tiles 300x200x6mm thick as in dado/skirting etc incl 10 mm thick rendering in CM 1:3, set & jointed in neat cement slurry & pointed in white or coloured cement slurry & pointed in white or coloured cement, complete all as specified and directed.

Cleaning and removing all scale and dirt etc by using bleaching powder from water tank and from mouth of circulating pipe,etc Capacity of tank n exc 250 litres.

All as per item No 71 above but Capacity of tank exc 250 litres & n exc 500 litres.

All as per item No 71 above but Capacity of tank exc 500 litres & n exc 1000 litres.

S&F in repair PVC ball valve 15mm dia with epoxy coateed aluminium rod and high density ball (minium weight 142 gms), complete all as specified and directed.

S&F in repair PVC ball valve 20mm dia with epoxy coateed aluminium rod and high density ball (minium weight 210 gms), complete all as specified and directed.

Taking down/out unserviceable UG cables of any cross sectional area and connections including Bricks, GI Pipes, etc of any descriptions, laid in trenches and/or fixing with walls/poles including segregating of serviceable materials viz Bricks, cables, GI Pipes etc, complete all as specefied and as directed.

S&F or passing through pipe, XLPE insulated, armoured, electric power UG cable (Heavy duty) with aluminium conductor, 1100 volts grade, nominal cross sectional area 6 sqmm 2 core including brass compression cable gland, terminal lug etc and testing, complete all as specefied and as directed. Make: Havells/Finolex/Anchor

All as per item No 77 above, but nominal cross sectional area 10 sqmm 2.0 Core.

All as per item No 77 above, but nominal cross sectional area 16 sqmm 4.0 Core.

M&L for LT cable two core PVC insulated, PVC sheathed multi stranded Copper conductor size 2.5 Sqmm for security light.

M&L GI tubing light grade 20 mm bore for protection of service connection laid in trenches/ walls etc and for protection of connection wire from junction box to light fittings, earth wire, complete all as specefied and directed. (Note : Necessary clamps, nuts, bolts etc deemed to be included)

S&F in repairs thermo plastic cable Junction box of size 300X200X105mm suitable for Cable IP 65 Protection with metric knockout for cable entry incl MS clamp of size 25x3mm, with aluminium bus bar 200 Amps 3 pole and neutral and MCB SP 16 Amps incl 3 nos HDPE gland fixed on pole with clamp nuts,bolts etc, complete all as specified and directed. Make:Sintex Hensal/HPL

Taking down worn out, unserviceable and supply & fixing pole street light bracket fabricated out of GI tubing light grade 40 mm bore Bend to the shape as directed and not less then length 1.0 mtr complete with mounting MS clamp of flat iron size 40X5mm of suitable length 02 Nos incl nut bolts etc of suitable size, complete all as specified and directed.

M&L for GI pipe light grade of size 40mm dia laying in trenches/ under floor/on walls for protection of UG cables, complete all as specified and directed.

All as per item No 84 above, but size 50mm dia.

M&L for removing old paint from surface of steel LT pole by scraping,rubbing and making good surface for painting with two coats of aluminium paint on rusted pealed out surface after cleaning ,marking nos as per direction, complete all as specified and directed. Make: ASIAN/Nerolac/Berger

M&L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.0 mm thick burried directly in gorund (earth pit not less than 2.25 Mtr normal ground level),and top edge of earth plate not less than 1.5 mtr below normal ground level, connected to galvanised means of earth wire 4 mm dia with bolts, nuts & check nuts, and washers of galvanised iron protection pipe light grade of 15 mm dia and watering pipe medium grade of 20 mm dia and filled with alternate layer of charcoal and common salt, watering funnel with wire mesh, earth pit chamber and cover CI frame PCC 1:3:6 type C-2 all as shown in electrical plate No-3 of SSR part-I of 2009 connected to earthing test point all as specified and indicated including all earth work excavation, returning filling and disposal of surplus soil and testing on completion.

Taking down worn out, old, unserviceable light fitting of any description, complete all complete as specified and directed.

S&F in replacement of LED Street light luminaries fittings 60 watt green line a road lighting luminaries with high power LED and unique peanut to ensure uniform light distribution higher spacing between poles and maintenance free system. Make-Crompton/Bajaj/Havells./ Phillips Note:- (i) The contractor shall produce minimum two years warrenty against any manufactures defect/ failure of fitting from the authorised representative / OEM of the make as specified and brought at site. (ii) The efficacy of system is 120 lumne/watt. (iii) The PF should be > 0.90 (iv) The LED street light fittings shall be provided with overload / under load protection with range 180 to 380 volts and inbuilt surge protection device. (v) The contractor / manufacture shall provide on site warranty for carrying out necessary repair / replacement of defective street light fittings. (vi) The LED fitting and driver in fitting shall be of same make. (vii) Street light should be with phase to phase and phase to neutral protection

All as per item No 89 above LED street light fitting 90W.

All as per item No 89 above LED street light fitting 45W

S&F LED Post top / Gate light 1x40 watt decorative type, 360° indirect light including fixing with suitable size GI pipe as requir on the top of gate pillor, control by two way SP DB with Suitable MCBs as per direction and wiring, complete all as specified & directed. Make : CROMPTON /Havells Bajaj/Phillips

S&F Garden Light/ Bollards 10W watt are made of extruded Aluminium, profiles with cast aluminium base,opal PC diffusers with integrated LED and driver, complete all as specified and directed. Make:- Crompton /Phillips/Havells/Bajaj

S&F LED Flood light 120W with IP 65 protection on 11 mtr flood light pole as per sample, complete all as specifed and directed. Make : CROMPTON/ Havells/Bajaj/Phillips

Taking down old unserviceable and Supply and fixing connecting and testing (in replacement) time switch panel box size 400mm x 350mm x170 mm dust and vermin proof made of 16 gauge MS sheet factory made duly painted with two coats of synthetic enamel paint recommended colour over a coat of red oxide primer and mounted inside the following .Note:- Time switch pannel box shall be fixed on one pole/wall in feeder pillar box with flat iron clamp 40x6 mm or other suitable fixing arrangement complete all as specified and directed by Engr-in-Charge. (a) MCB triple pole 32 Amps 230 volt-01 No (b) Analog electro mechanical time switch 24 hours with minimum setting 30 minutes for daily working contact rating 16 Amps,240 volts,AC with initial charging battery backup having supply and reserve failure upto 150 Amp hours and coil voltage 415 volts (c) AC contactor ,3 pole,ML-2,415 Volts,50 Hz (d) intenal wiring with pvc insulated stranded copper conductor of suitable size and making electric connection -01 No. (e) By pass MCB single pole ,32/40 Amps,230 volts-01 No. Note:- Time switch pannel box shall be fixed on one pole/wall in feeder pillar box with flat iron clamp 40x6 mm or other suitable fixing arrangement, complete all as specified and directed.

Taking out the submersible motor from bore/open well upto 17.5 HP including GI pipe of 50/65 mm dia complete all as directed and transportation of submersible motor upto 17.5 HP 3 Phase from pump house at any location in Namkum area under AGE E/M Namkum Yard, transporting to contractors workshop, dismantling and carrying out necessary repair/replacement of motor including reassembling, testing and commissioning for satisfactory operation as per the following :- (a) Cutting out existing winding of starter of submersible motor of any make and rewinding with same size of copper winding wire as existing as directed by the Engineer-in-Charge. (b) Straightening the slot of water of submersible motor of any make. (c) Replacement of thrust bearing block complete of submersible motor of any make. (d) Replacement of worm-out bushes of submersible motor as per manufactures design and specification. (e) Replacement of submersible cable 3 Core of suitable size 4 Mtr long complete with suitable clips. (f) Replacement of sand guard. (g) Providing of sleeves in end plate of submersible motor. (h) Replacement of cable gronment. (j) Replacement of water seal. (k) Replacement of studs with nuts. (l) Remetlling of motor shaft, turning to bring it to original size and shape and plastering of shaft of submersible motor. (m) Painting of motor and tranporting it back to site/store yard and testing to the entire satisfaction of Engineer-in-Charge.

All as per item No 96 above but of capacity upto 10 HP.

All as per item No 96 above but of capacity upto 7.5 HP.

All as per item No 96 above but of capacity upto 5 HP.

All as per item No 96 above but of capacity upto 25 HP.

All as per item No 96 above but of capacity upto 60 HP.

Reparing of submersible pump upto 17.5 HP and lowering down of motor pump set with GI pipe and rope all as directed and transportation of submersible pumps upto 15 stage from pump house at any location in Namkum area under AGE E/M Namkum Yard, transporting to contractors workshop, dismantling and carrying out necessary repairs/replacement of pumps/testing as the following :- (a) Replacement of coupling of submersible motor pump key. (b) Overhauling of submersible pump and carrying out the following repairs. (c) Balancing of pump shaft and cutting of key slots. (d) Minor repairs of bowel assembly. (e) Re-threading of worn-out studs holes and providing over size studs with nuts. (f) Replacement of bowels bushes. (g) Replacement of neck ring. (h) Replacement of steel distance pieces. (j) Replacement of impeller. (k) Replacement of bowel. (l) Replacement of head extension. (m) Painting of pumps and transporting it back to site/store yard and testing to the entire satisfaction of Engineer-in-Charge.

All as per item No 102 above but of capacity upto 10 HP.

All as per item No 102 above but of capacity upto 7.5 HP.

All as per item No 102 above but of capacity upto 5 HP.

All as per item No 102 above but of capacity upto 25 HP.

All as per item No 102 above but of capacity upto 60 HP.

S&F PVC insulated submersible cable water proof flat type 3 core with stranded copper conductor cable, 6 Sqmm, 1100 Volts grade inculding cable lugs/joints, connection to submersible motor and other end to aluminium amoured cable including jointing, complete all as specified and directed. Make: HPL / Havell's

All as per item No 108 above but of 4 Sqmm, 1100 Volts submersible cable.

S&F HDPE borecaps of size 250 mm dia, complete all as specified and directed.

Replacement of old rusted GI Column Pipe medium grade of size 65 mm dia in pieces of 3.3 Metre long, lathe m/c threaded both ends in the bore/open wells, complete all as specified and directed.

All as per item No 112 above but of 50 mm dia.

S&F of steel rope in submersible bore wells from motor to top edge of the bore well of size 6 mm dia (Multi wire stainless steel) for holding of submersible pump motor set, complete all as specified and directed.

M&L GI flange joints with rubber gasket or 3 mm thick chemically treated compressed including suitable size bolts, nuts and washer complete as directed of size 65 mm dia, complete all as specified and directed.

All as per item Srl No 115 above but of size 50 mm dia.

S&F MS work as/or holding MS clamps on tube well for delivery/column pipe, fabricated out of flat iron section as directed, made to shape drilled fixed with 16 mm dia MS bolts, nuts, washers etc including one shop coat of red oxide primer, after preparation of surface, complete all as specified and directed.

Flushing/cleaning of bore well including taking out and lowering of new /repaired submersible pump set of any size (5 HP to 17.5 HP), 3 Phase 400/415 Volts in 200/250 mm size tube well upto existing depth of bore comprising following nature of work:- (a) Dip connecting existing pipe connection in any size and removing electric connection. (b) Errection of trapord/chain pulley lock at site. (c) Unscrewing the submersible pump and removing the same at site for relowering. (d) Transporting the trolley mounted DTH machine at site for flusing the bore well/further boring if required. (e) Flushing the bore hole through compressor operating 120 PSI after lowering the rig in length 1.5 Mtr x 80 Nos continously till clear water in obtained not less than 8 hrs.

M&L for dismantling the power supply of electric motor any type including dismantling from pump and taking to workshop with necessary transportation and opening the complete motor and rewinding the rotor with super enameled copper wire as per the existing guage with necessary insulation, sticks and varnishing, including replacement of shaft bearing of shaft and replacement of bearing 02 Nos and motor terminals plate/cable ducts and minor repair of strater complete of capacity 100 HP including two coat of synthetic enamel painting complete all as directed including reassembling, testing and commissioning for satisfactory operation.

All as per item No 119 above but of capacity 40 HP electric motor any type.

All as per item No 119 above but of capacity 30 HP electric motor any type.

All as per item No 119 but of capacity 20 HP electric motor any type.

All as per item No 119 above but of capacity 7.5 HP electric motor any type.

All as per item No 119 above but of capacity 1 to 1.5 HP electric motor/booster pump any type.

M&L dismantling complete Centrifugal/Mono Block Pump set of any type and overhauling the pump re-threading of wornout holes of studs and providing over size studs with nuts and washers. Remantlling and balancing of shaft, replacement of gunmental bush, all bearing type 6309/6307/6307C etc and gland packing (12/8 mm) of pump set and refitting the same after the repair all as specified capacity 100 HP including two coat of synthetic enamel painting, SM No writings etc, complete with base etc all as directed.

All as per item No 125 above but of capacity 40 HP.

All as per item No 125 above but of capacity 30 HP.

All as per item No 125 above but of capacity 20 HP.

All as per item No 125 above but of capacity 7.5 HP.

All as per item No 125 above but of capacity 1 to 1.5 HP.

M&L Cement concrete (1:4:8) Type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete, all as specified and directed.

Removing excavated material n.exc 50 m and depositing where directed at a level n.exc 1.5m above the starting point, complete all as specified and directed.

Excavation in trenches, n.exc. 1.5 m wide and n.exc 1.5m in depth for foundation and getting out in soft/loose soil, comlete all as specified and as directed.

Demolition of cement contrete in ground floors and paving n.exc 15 cm thickness (below or above ground level), complete all as specified and as directed.

Construction of Brick masonry valve chamber of size (90 x 90 x 105) cms (internal dimension) chamber depth to be reckoned from the top of PCC foundation to top of brick wall, including PCC 1:4:8 type D2 in foundation PCC 1:2:4 type B1 in coping, brick work in cm 1:4, plaster 15 mm thick in CM 1:4 flush pointing externally as the work proceeds in CM (1:4), MS sheet cover 3.15 mm thick with handle and locking arranging and angle iron frame of size (25 x 25 x 5 mm)including painting with two coats of synthetic enameled paint over a coat of red oxide primer, complete all as specified and directed.

Dismantling of existing/damaged masonry valve chamber of any size, complete all as specified and directed.

M&L in repairs gun metal gate or globe valves with iron wheel head (ISI Marked), screwed both ends for iron pipe and fixed of size 15mm bore, complete all as specified and directed. Make : Shakti/Leader/Vardhman/BIR Jalandhar.

All as per item No 137 above but of size 20 mm bore.

All as per item No 137 above but of size 25 mm bore.

All as per item No 137 above but of size 40 mm bore.

All as per item No 137 above but of size 50 mm bore.

S&F GI Tubing medium grade ISI marked including all fittings laid in trenches/fixed on wall of size 15mm bore, complete all as specified & directed.

All as per item No 142 above but of 20 mm dia .

All as per item No 142 above but of 25 mm dia.

All as per item No 142 above but of 40 mm dia.

All as per item No 142 above but of 50 mm dia.

Taking up or down GI tubing and connection and stacking neatly for reuse and removing the balance material from site of size 15 mm bore, complete all as specified and directed.

All as per item No 147 above but of 20 mm dia.

All as per item No 147 above but of 25 mm dia.

All as per item No 147 above but of 40 mm dia.

All as per item No 147 above but of 50 mm dia.

M&L for dismantling the power supply of electric motor of STP including dismantling from pump and taking to workshop with necessary transportation and opening the complete motor and rewinding the rotor with super enameled copper wire as per the existing guage with necessary insulation, sticks and varnishing, including replacement of shaft bearing of shaft and replacement of bearings and motor terminals plate/cable ducts and minor repair of strater complete of capacity 5 HP including two coat of synthetic enamel painting complete all as directed including reassembling, testing and commissioning for satisfactory operation.

M&L dismantling complete Centrifugal/Mono Block / STP Pump set of any type and overhauling the pump re-threading of wornout holes of studs and providing over size studs with nuts and washers. Remantlling and balancing of shaft, replacement of gunmental bush, all bearing type etc and gland packing (12/8 mm) of pump set and refitting the same after the repair all as specified capacity 5 HP including two coat of synthetic enamel painting, SM No writings etc complete with base etc, complete all as specified and directed.

S&F MCCB four pole 415 volts 50 Hz 250 amps of capacity 25 KA with thermal magnetic release complete with all accessories. Make :Havells/Legrand/Schnider/HPL

S&F MCCB four pole 415 volts 50 Hz 400 amps of capacity 25 KA with thermal magnetic release, complete all as specified and directed. Make :Havells/Legrand/Schnider/HPL

Dismantling and Repair/maint of Lt panel/starter panel of centrifugal motors of any capacity, complete all as specified and directed.

S&F Dry run and over load protection with phase failure relay alongwith suitable CTS-01 Set and single phase preventor.

S&F Surge protector of suitable rating 3 Ph 4 wire based 415 Volts AC. Make :- Schinder/Hanger/Siemence.

S&F Contractor suitable for 5 HP to 17.5 HP submersible pump motor.

M K Enterprises

M/S Sahib N Sahiba Enterprises

Raj Construction

BHARATI ENTERPRISES

M/S ABDHESH CONSTRUCTION

ISHAAN ENGINEERING

M/S JAI MATA DEE CONTRUCTION CO.

M/s Dwarika Nath Singh