ADDN/ALTN TO OTM ACCN AND SINGLE OFFRS ACCN AT NAGROTA

Amount

Taking down carefully copper/aluminium point wiring (light, fan, bell, socket or power, security light) complete, including fixtures and fittings such as switches, ceiling roses, holders,regulators, sockets, tube light fittings and including making good the disturbed surfaces to match with existing surface and colour shade with putty and white cement for smooth finishing of holes, small patches etc, complete all as specified and directed.

Taking down carefully ceiling fan/exhaust fan/air circulator fan any sweep, any size, removing blades & deposited to MES store, complete all as specified and as directed

Taking down existing energy meters, keeping aside safely & refixing the same in its original position after completion of point wiring/sub main wiring, complete all as specified and directed.

Taking down existing electric water heater, keeping aside safely & deposited to store, complete all as specified and as directed

Taking down MCB DB of any size including MCBs of any size and making good disturbed surfaces complete all as specified.

Fixing only LED light fitting any type, as obtained from site with driver, holder including LED tube light connecting with three core flexible copper conductor of 1.5 sqmm from ceiling rose complete all as specified and directed.

Point wiring for One light point controlled by one switch 5 Amp single pole one-way complete with 1.5 Sqmm (nominal area) PVC insulated, unsheathed and multi strand copper conductor FRLSH cable (ISI marked) drawn into and including PVC concealed conduit (medium quality) and conduit fittings including 1.5 Sqmm PVC insulated unsheathed and multi stranded copper conductor FRLSH cable as earth wire to common earth and connecting to earth dolly including cutting of chases/wall/floor and suitable size of powder coated CRCA mild steel sheet modular sunken box for fixing modular switches, sockets, regulators with frame and top modular cover plate and machine made brass screw and washers etc complete all as specified and directed.

All as Per Srl item No. 7 above but one light point controlled by two way switche.

All as Per Srl item No. 7 above but one call bell point controlled by one bell push point.

All as Per Srl item No. 7 above but for one ceiling fan/exhaust fan point.

All as Per Srl item No. 7 above but for one 3 pin 5 amp socket on same board.

All as Per Srl item No. 7 above but for one 3 pin 5 amp socket on independent board.

All as Per Srl item No. 7 above but with 2.5 sqmm copper conductor for 15 amp socket with 2.5 sqmm earth continuity copper conductor

Modular switch one way 5/6 Amps, 1 Module complete all as specified.

Modular switch two way 5/6 Amps, 1 Module complete all as specified.

Modular Bell push, 5/6 A, 1 Module complete all as specified.

Modular socket 5 pin, 5/6 Amps, 2 Module complete all as specified.

Modular switch one way, 15/16 Amps, 1 Module complete all as specified

Modular socket 5/6 pin, 15/16 Amps, 2 Module complete all as specified.

Ceiling rose, surface backalite, of suitable size, three terminals complete all as specified

Electric bell, AC, 230 volts single phase Ding Dong Type complete all as specified.

Lamp holder, PVC / Polycarbonate type with back plate suitable for batten fittings including 9 watt LED lamp, complete all as specified and directed.

Ceiling fan complete with blades, down rods and accessories, 230V, 1200mm sweep, min air delivery 210 CFM, with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC), complete all as specified and directed.

Electric water heater, storage type, steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc; complete all as specified.

LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, including provision of GI bracket made of 40mm dia, GI pipe, 1.5m long, bend to shape, complete all as specified.

LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose including taking down unserviceable tube light fittings, complete all as specified and directed.

LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED tube light including connecting up with three core flexible copper conductor cable of suitable size including taking down unserviceable tube light fittings, complete all as specified and directed.

Exhaust fan, steel body, heavy duty, AC, single Phase, 230V, of size 300mm sweep with, blades, and frame and louvers all as specified and directed.

Air circulator fan, heavy duty, 230 V AC, having sweep size of 400mm, complete all as specified and directed.

Sheet metal enclosure MCCB/MCB DB VTPN 4 way double door made powder coated, CRCA mild steel, 415 volts, 200 amps rated bus bar, dust and vermin proof suitable for incorporation of MCCB/MCBs duly flush in wall and making good to disturbed surface complete all as specified and directed.

Sheet metal enclosures DB's double door factory made power coated made out of CRCA mild steel sheet 1.6 mm thick with metallic painting white series, 240 volts 200 amps rated enamelled bus bar 8 way dust and vermin proof proof suitable for incorporation of MCBs duly concealed in wall and making good to disturbed surface and colour matching, fixed in repair, complete all as specified

MCCB, 4 pole, 63 Amp, 415 Volt, 16 KA, complete all as specified

MCCB, 4 pole, 100 Amp, 415 Volt, 16 KA, complete all as specified

MCB, SP, 240 Volts, 40 Amps,10KA, B curve, complete all as specified.

MCB, SPN, 240 Volts, 32 Amps, 10 KA, B curve, complete all as specified.

MCB, SP 240 Volts, 6 Amps to 32 Amps, 10 KA, B curve, complete all as specified.

LED luminaire 600mm x 600mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holder & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size including taking down existing fittings, complete all as specified and as directed.

Sub main wiring with two run of single core FRLSH PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 6 Sqmm drawing through and including concealed rigid non metallic PVC conduit medium grade (ISI marked) 20mm dia or above required including one single core FRLSH PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 6 sqmm as earth continuity conductor connected to commen earth and earth dolly complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6mm buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of earth plate not less than 1.5m below normal ground level connected with galvanized iron earth lead wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel complete with 15mm dia GI light grade protection pipe, 20mm dia GI medium grade watering pipe with funnel including charcoal, dust, salt, PCC M-15 type B1 in pit with angle iron (25x25x3)mm frame work with precast RCC 1:2:4 type B-1 cover reinforced with 8mm dia TMT bars @ 150mm C/C both ways and 12mm dia MS fabricated handle, test point etc. in and including light grade GI protection pipe 20mm bore up to 7.5m length for drawing in earth lead wire, all as shown in electric plate No. 3 of SSR Part-I complete with necessary earth work in any type of soil, removal of soil to a distance not exc. 50m, testing on completion complete all as specified and directed. Note:- On testing after completion of earthing, if desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own risk & cost to the entire satisfaction.

Modular fan regulator 120 watt 2 module, complete all as specified.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in any type of soil including removal of excavated material to a distance not exceeding 50 mtr and deposited where directed at a level not exceeding 1.5 mtr above the starting point, complete all as specified and directed.

Hard core of broken stone or boulders gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm, thick watered and rammed to a true surface complete all as specified and directed.

75mm thick, plain cement concrete type D-2, 1:4:8 (using 40mm graded crushed stone aggregate) as in sub base of flooring / hard standing etc; complete all as directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete (using 20mm graded crushed stone aggregate) in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete all as specified and directed.

Earth work in excavation by mechanical means (Hydraulic excavator)/ in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out in any type of soil (the excavated soil) and disposal of surplus excavated soil, within a lead of 50m complete all as specified and directed.

Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete, complete all as specified and as directed.

Rendering 15mm thick in cement mortar 1:4 on fair faces of brick work (manhole and similar work), finished even and smooth without using extra cement including mixing of water proofing compound as per manufacture instruction, complete all as specified. Note: Water proofing compound shall be measured and paid separately as supply only.

Supply only liquid water proofing compound.

Plain cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in copings, benching including weathering slightly rounded or chamfered angles including necessary formwork and finishing the exposed surfaces, complete all as specified and directed.

Precast RCC (1:2:4) type B-1, using 20mm graded crushed stone aggregate as in cover slab (for manhole etc), landing chullah hoods, chajjas, water troughs, mangers, sheleves and similar articles with plain faces complete set in cement mortar (1:4) including use of form work complete all as specified and directed.

Mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

Returning, filling in any type of soil including spreading, levelling, watering and well ramming in layers not exceeding 25cm, complete all as specified and as directed.

Removing excavated material not exceeding 100m and depositing where directed and depositing where directed at a level not exceeding 1.50m above the starting point complete all as specified and directed.

Reinforced concrete pipes, class NP3, laid and jointed complete with collars, bore of pipe 150mm dia, laid in trenches in concrete bedding and jointed complete in cement mortar (1:1) complete all as specified and directed.

PCC 1:3:6 type C-2 (using 20mm graded crushed stone aggregate) as in concrete bed to 150mm dia drain pipes including packing under and hunching against the sides of pipes after they are laid and tested, complete all as specified and directed.

Cutting holes in brick walls exceeding half brick and not exceeding one brick wall in cement mortar for inserting holdfasts or pipe and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required, complete all as specified and directed.

Construction of septic tank for 50 users (Brick construction) complete shown on drg No. CEUZ /TD-1585/2021 sheet 1/4 to 4/4 complete all as specified and directed.

Construction of soakage well (Brick construction) 2.40mtr dia and 3.0mtr deep below inlet pipe level (depth from inlet pipe to ground level 45cm), complete all as specified and shown on drg No. CEUZ/TD-1585/2021 sheet 1/4 to 4/4 complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coat of cement base paint over a coat of primer complete all as specified and directed

Demolition of brick work or stonework built in cement mortar including all quoins, arches pillars etc but excluding ashlar facings ,dressed stonework and precast concrete articles and stacking the serviceable materials within 100m and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed.

Plain Cement concrete 1:2:4 type B-1 (using 12.5mm graded crushed stone aggregate) as in louvers and jallies, 25mm thick (measured solid), including all mouldings but excluding frame and set in cement mortar 1:4, complete all as specified and directed.

Brick work with sub class 'B' bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:4 complete all as specified.

Demolition of cement or lime concrete in any description along with tar felt treatment in roof and cement mortar bedding from roof, removal of debrish out side MD land complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semi corrugated; etc) sheets in roof coverings, complete all as specified and as directed.

Brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan exceeding 6m in mean radius, built in cement mortar 1:6 including flush pointing in same mortar as work proceeds, complete all as specified.

All as per Srl item No 66 above but except bricks

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level), complete all as specified and directed.

Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed.

Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed.

Dismantling wall and ceiling boards (fiber, pulp, insulation; etc) or insulation boards / slabs / blankets; any thickness including cover fillets, complete all as specified and as directed.

Aluminium anodized snap grid (powder coated) frame work of grid size 605x605mm including hangers 6mm dia GI (upto 1200mm long) for false ceiling including notching and preparing holes, including aluminium cleat/corner pieces and GI 4mm dia suspenders with utterly clips, wall angle of size 24 x 24mm, main runner (tee) of size 24 x 38mm, cross tee of size 24 x 28mm, (No of suspenders shall be decided by the GE as per actual size requirement) including 4mm thick non asbestos fibre cement plain building boards fixed to aluminium snap grid and providing two coats of oil bound distemper including preparation of surfaces, complete all as specified and directed.

Mild steel work as wind ties for roof including securing bolts conforming to, Fe-290 Gde, E-165 complete all as specified and directed.

Pressed steel frame of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. including one coat of red oxide providing and providing mild steel bars 6mm dia threshold bar and including filling hollow portion of frame with PCC (1:3:6) type C-0 using 12.5mm graded crushed stone aggregate complete all as specified and as directed

Pressed steel frame of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. including one coat of red oxide providing and providing mild steel bars 6mm dia threshold bar and including filling hollow portion of frame PCC (1:3:6) type C-0 using 12.5mm graded crushed stone aggregate complete all as specified and as directed

Factory made, HDF prelaminated moulded door shutter, 35mm thick (style with 2, 4 or 6 raised panel design with 2mm thick 3D wood grain moulded PVC sheet on the front face and 2mm plain colour PVC sheet on back face, supplied and fixed to frame at site all as per specification and drawing No CEUZ/TD-1343/2013 sheet No 1/1 complete all as specified.

Factory made, single piece wire gauzed panel HDF door shutter 35mm thick (style) with 2, 4 or 6 raised panel design including GI wire gauge complete supplied & fitted in the frame at site as per specification and drawing No CEUZ/TD-1343/2013 sheet No 1/1 complete all as specified.

Box type steel window with side hung double shutter with provision for desert cooler / AC (inside for wire mesh & out side for glass) including guard bar, hinges, steel, handle, tower bolt and steel peg stay complete with glazing bar dovetailed or welded and fixed steel window shall be conforming to relevant IS complete all as shown on drawing No CEUZ/TD/1517/15 sheet No 1/3 to 3/3 and directed. (Note: Wire mesh and sheet glass shall be measured and paid separately).

Box type steel ventilators top hung double shutter (inside for wire mesh & outside for glass), including guard bar, hinges, steel handle tower bolt and steel peg stay complete with glazing bar dovetailed or welded steel ventilators shall be conforming to relevant IS complete complete all as shown on drawing No CEUZ/TD/1517/15 sheet No 1/3 to 3/3 and directed. (Note: Sheet glass shall be measured and paid separately).

Machine cut kota stone flooring 20-22 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing ( mirror finish) (Each stone not less than 55cm x 55cm) over and including 15mm thick screed bed in cement mortar (1:4) as in floor finished rough including roughening of existing surfaces by pick axicess and applying a coat of cement slurry @ 3 Kg/Sqm of surface, complete all as specified and directed.

Machine cut kota stone slab 20-22mm thick in skirting, dado and pillar and riser of stair case, (in single piece) size as required jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing (mirror finish) over and including 15mm thick rendering in cement mortar (1:4) including taking out of existing plaster, complete all as specified and directed.

Sheet glass, 3.00mm thick, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed.

Figured glass, 3.00mm thick, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm.in each pane, complete all as specified and directed.

Preparation of old steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and painting with one coat of synthetic enamel paint complete all as specified and directed.

PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in roof kerbs, padding, mud stops etc; complete all as specified and as directed.

Rendering 10mm thick in cement mortar 1:4 on roof surfaces including liquid water proofing compound @ 200 ml per bag of cement finished even and smooth without using extra cement, complete all as specified and directed.

APP (atatic polypropylene) modified membrane 3mm thick and weight not less than 3.00 Kg per Sqm with 160 GSM/Sqm, non woven polyester mat as centre core reinforcement laid over a coat of bitumen 85/25 at the rate of 1.2 Kg per sqm with 100mm over lap the membrane has to be laid with LPG torch and over lap sealed and finished neat over roof / sunken floor including APP membrane complete all as specified and directed. Note: APP based polymeric membrane of approved manufacturer will be laid/fixed by authorised person of the same manufacturers.

Applying two coat of bituminous based aluminium painting @ 0.15 kg/Sqm each coat on water proofing treatment with preparation of surfaces complete all as specified and directed at site.

PCC 1:7:12 type F-2, (40mm graded crushed stone aggregate) as in sunken floor filling and mass concrete complete all as specified and directed.

Mild steel framed work as in staging for water storage tanks with grills, doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to Fe-290- W(Gde-E-165) complete all as specified and as directed.

Preparation of new steel surfaces over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Disconnecting existing tanks of capacity exceeding 250 and not exceeding 500 litre, setting aside (or lowering if required) for repairs, cleaning, etc; and hoisting if required reconnectioing and re-fixing in position, complete all as specified and directed.

Rotational moulded polyethylene water storage tanks of 1000 Litres capacity (ISI marked), (cylindrical vertical tanks with closed top) (White in Colour and three layered) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including dismantling existing water tanks and removing to store complete all as specified and directed.

Ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe or brass ferrule and fixed, 20mm bore, complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning for refixing or removal to store 15mm bore complete all as specified and as directed.

Taking up or down steel tubing and connections including cleaning for refixing or removal to store 20mm bore complete all as specified and as directed.

15mm bore, GI tubing medium grade with all fittings and fixed to walls and ceiling and floor/roof complete all as specified.

All as Per Srl item No. 97 above but except pipe.

20mm bore, GI tubing medium grade with all fittings and fixed to walls and ceiling and floor/roof complete all as specified.

All as Per Srl item No. 99 above but except pipe.

Taking down chowkhats or frames with shutters (without taking off shutters from frames) exceeding 1.5 sqm but not exceeding 4 sqm each, complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 Sqm each, complete all as specified and directed.

Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, door seal at bottom,anodised aluminium snap beading screws etc. (thickness of powder coating should not less than 50 micron) complete all as specified and directed.

Powder coated aluminium frame work (minimum thickness of powder coating 50 micron) for doors, windows, ventilators and partition, (sliding/openable/fix doors, windows, ventilator), etc with one, two or more rebates (reqd as per site), including joining cleat for fixing with dash fasteners of required dia and size, including filling up gaps at junctions, ie top, bottoms and sides etc complete all as specified and directed.

Powder coated aluminium work (minimum thickness of powder coating 50 micron) for window, ventilator shutters and partition wall, etc; sliding/openable/fixed (as per required at site) type without sash bar, aluminium section weighing 0.55 kg/m, including necessary locking arrangement, guide wheels, joining cleats, glazing clips rubber packing anodised aluminium snap beading screws etc; complete all as specified and directed.

Sheet glass plain/coloured (as approved by GE), 5.5mm thick, and glazing with rubber packing, screws or glass putty in squares exceeding 0.5 Sqm each pane complete all specified.

Stainless steel wire cloth of 0.36mm dia wire and average width of aperture 1.40mm & fixed with tacks or screws, wire staples, etc complete all as specified and directed.

Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and as directed.

Stainless steel, 20mm to 25mm dia, drapery/Harrison rail / curtain rod with brass /nickel chrome polish / designer lattos and brackets complete all as specified and approved by GE including taking out old pelmet with curtain rods complete all as directed.

Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube with wooden grain printed PVC sheet used inserted of plain colour PVC sheet & edges will be painted to match with printed sheet complete all as specified and directed.

Factory Made Solid PVC moulded door shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site complete all as specified and directed.

Taking down cement plaster on brick or concrete surfaces, parapets including raking out joint, hacking for key, scrubbing down with water, at any description with necessary scaffolding of max height for G+2 storied etc complete all as specified and as directed.

Rendering 10mm thick, in cement mortar (1:6 ) on wall/ concrete surfaces finish even and smooth without using extra cement, complete all as specified and directed.

Rendering 15mm thick, in two layer (10mm+5mm) in cement mortar 1:4 on fair faces of brick work / concrete surfaces finished even and smooth with out using extra cement with water proofing compound complete all as specified and as directed. Note:- (i) water proofing compound on only top layer of plaster (ie 5mm thick) (ii) Qty of WPC 200ml per cement Bag as per manufacturer instructions (iii) WPC shall be measured and paid separately as supply only.

Rendering 5mm thick, in ceiling cement mortar (1:3) on concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

Preparation of new plastered surface of wall and applying two coats of oil emulsion distemper over a coat of primer over and including 1mm thick wall care putty complete all as specified and directed.

Anti fungal weather coat on two coats of new plastered surface with acrylic smooth exterior emulsion paint applied 1.67kg/10sqm of required shade over a coat of primer applied 2.20kg/10Sqm on new surfaces including preparation of surfaces, including necessary scaffolding for max height of G+2 stories, etc complete all as specified and directed. Make of Acrylic emulsion weather coat paint:- Asian (Apex Ultima), Berger (Super coat ) or ICI Dulux (weather shield). Make of primer:- sian or Berger or ICI Dulux.

Complete removal of old plastered surfaces and applying two coats of anti fungal weather coat with acrylic smooth exterior emulsion paint applied 1.67kg/10sqm of required shade over a coat of primer applied 2.20kg/10Sqm on old surfaces including preparation of surfaces, including necessary scaffolding for max height of G+2 stories., etc complete all as specified and directed. Make of Acrylic emulsion weather coat paint:- Asian (Apex Ultima), Berger (Super coat ) or ICI Dulux (weather shield). Make of primer:- Asian or Berger or ICI Dulux.

Preparing new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

Preparation of old decorated plastered or unplastered surface including complete removal by machanical mean only, scraping down smoke soot, moulded, moss, efflorescent salt, trading oil and greasy spots and applying two coat of Oil emulsion distemper on walls over 1 mm thick wall care putty, complete as specified and directed.

Preparation of old plastered surfaces of ceiling and applying two coat of white wash, complete all as specified and directed.

Printed PVC sheet, 5mm thick, used instead of plain colour PVC sheet plain colour PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC wall lining, insulated PVC wall lining, and solid PVC partitions inclusive of solvent cement and fixing at site, complete all as specified and directed.

5mm thick, PVC sheet, fillet of width 35mm, for wall panelling inclusive of fixing on to wall to make PVC frame as per specification and drawing, complete all as specified and directed.

8mm thick, seamless calcium silicate, ceiling made out of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25mm long self drilling and tapping screws having Philips head with under head cutter at 200mm centre to centre including finishing thr joints of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seamless finish with 8 mm thick for seamless false ceiling fixed with screw over and including Gl frame work comprising of Gl perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx. 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete as per manufacturer instruction including two coats of oil emulsion paint over and including 1mm thick, wall care putty, complete all as specified and directed.

Non skid joint free coloured ceramic floor tiles 7mm to 8mm thick, (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the surface with and including 15mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed.

Glazed ceramic coloured tiles of size 300mm x 450mm x 7mm thick as on vertical surfaces such as wall, dado ,skirting etc set and jointed in neat cement slurry and pointed with coloured cement to match over and including 10mm thick backing coat on fair faces of brick work in cement mortar (1:4) complete all as specified and as directed.

Vitrified Ceramic tiles, 10mm thick, (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry with and including 15mm thick screed bed or bedding layer in cement mortar (1:6) complete and pointed in white or coloured cement to match

All as per item No 130 but as in skirting including 10mm thick, rendering in cement mortar (1:4).

S & F in repair 100mm bore cast iron pipe (sand cast pipes), waste and vent pipes in any length with or without ears including jointing with cement joints , laid in trenches or in floors or in walls, complete all as specified and as directed.

S & F in repair 75mm bore cast iron pipe (sand cast pipes), waste and vent pipes in any length with or without ears including jointing with cement joints , laid in trenches or in floors or in walls, complete all as specified and as directed.

S & F in repair cast iron bends diminishing pieces or tapers including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), dia of outlet 100 mm bore complete all as specified and as directed.

S & F in repair cast iron bends diminishing pieces or tapers including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), dia of outlet 75mm bore complete all as specified and as directed.

PCC 1:3:6 type C-2 (20mm graded crushed stone aggregate) 75mm thick as in plinth protection and finishing the surface even and fair w/o using extra cement complete all as specified and directed.

Forming 12mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’, completed all as specified and directed.

150mm long, aluminium anodised barrel tower bolt of extruded section and fixed completed all as specified and directed.

100mm mild steel butt hinges, medium weight, cold rolled and fixed, completed all as specified and directed.

150mm long aluminium handles cast type, anodised and fitted, completed all as specified and directed.

Aluminium alloy anodised sliding door with hasp staple(bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolts of extruded section or cast aluminium alloy and fixed 300mm long, complete all as specified and as directed .

300mm long ordinary MS rat tail rod pattern springs including roller and roller plate complete, complete all as specified and as directed .

Floor doors stoppers of aluminium alloy body and tenque anodised with hard drawn steel spring fixed in floor 150mm long, fixed in repair, complete all as specified and as directed.

Door closer hydraulically , aluminium extruded section of regulated, designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and as directed.

18mm to 20mm thick, granite, (of any type) work (single piece table rubbed and polished, size as directed at site) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with 15mm thick screed bed or bedding layer in cement mortar (1:6) complete and pointed in white or coloured cement to match, complete all as specified and as directed.

S & F in repair vitreous china premium/ 1st quality wash down water closet floor mounted EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flush pipe) complete all as specified and as directed.

S&F in repair PVC valve less, symphonic action type, flushing cistern 10 litre capacity, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe complete all as specified and as directed.

Toilet paper holder with flat recessed type stainless steel complete all as specified and as directed.

Fixed in repair plastic water closet seat cover, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

Vitreous China wash basin, white, flat back, size 630x450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed.

Sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Health faucet (ABS Body), Mild steel, chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

Supply and fixing in repair chromium plated, shower roses of 125 mm size with or without swivel joints, including fixing to steel pipe or union complete all as specified and directed.

S & F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S & F in repair soap dish, chromium plated approximate size 160x 160x90mm complete all as specified and directed.

S&F in repair stainless steel plate rack wall mounted type with 5/6 partition of size 600mm x 900mm x 250mm made out of 1mm thick stainless steel sheet complete all as specified and directed.

S&F in repair steel grating doom 125mm dia with waste hole complete all as specified and directed.

Brass chromium plated tubular towel rail 20mm dia(D) type 60cm long between flanges, fixed in repair, complete all as specified and as directed.

PVC connection 15mm bore size with PTMT nuts of length 600mm complete all as specified and as directed.

Towel Ring of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified and as directed.

Stop valve (angle valve), 15mm bore dia, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, screwed for iron pipe or for fixed unions and fixed in repair, complete all as specified and as directed.

S&F in repair brass CP mixer 15mm central hole for WHB for mixing hot & cold water screwed down for iron pipe and fixed, complete all as specified and as directed.

S &F in repair bib taps 15mm, cast copper alloy, fancy type, chromium plated, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and as directed.

S&F in repair 15mm Stop valves, cast copper alloy, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed (concealed type), complete all as specified and as directed.

S&F in repair wall mixer 3 in 1, 15 mm dia, chromium plated fancy type high pressure with letered hot and cold complete all as specified and as directed.

Gun metal globe or gate valves 20mm, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Pre laminated particle board,18/19mm thick, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screw to timber/PVC work fixed in repair as cupboard shelve and shutter complete all as specified and directed.

External teak wood lipping, 6mm thick fixed with nails complete all as specified and directed.

Hasp and staple of size 100mm aluminium anodised safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

Butt hinge of size 50mm, medium weight, cold rolled mild steel complete all as specified.

Dismantling of PVC pipes including fittings taking out of trenches or walls as required dia of pipe 100mm, complete all as specified.

PVC (SWR) pipes, grade 'A' (ISI marked), 110mm bore, single socketed in any length with rubber ring joints fixed to wall, complete all as specified and as directed.

PVC (SWR) pipes, grade 'A' (ISI marked), 110mm bore, single socketed in any length with rubber ring joints and laid in trenches/floors, complete all as specified and as directed.

PVC (SWR) bends (ISI marked), any radius for 110mm bore with oval access door, complete all as specified and as directed.

Writing letters or figures (Block. Roman, Italic or Indian) not exceeding 30cm high complete all as specified and directed

Brass Hat and coat hooks, solid body, 175mm to 250mm complete all as specified and directed

Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed

Hard drawn steel wire fabric (in available size) not exceeding 4 Kg per sqm complete all as specified and directed

Fixing only hard drawn steel wire including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire, complete all as specified and directed

Dismantling of water tanks exceeding 500 but not exceeding 1000 litre capacity, complete all as specified and as directed.

Fixing only ceiling fan/exhaust fan/air circulator any sweep, any size including connecting with three core flexible copper conductor of 1.5 sqmm from ceiling rose complete all as specified. Note:- Contractor will fix and commissioning ceiling fan/exhaust fan/ air circulator provided by the department (old & new) against the taking down under respective items. Cost of additional wire & lugs shall deemed included in quoted rates.

Fixing only electric water heater (Geyser) of any size including connecting with three core flexible copper conductor of 2.5 sqmm and plug top complete all as specified. Note:- Contractor will fix and commissioning electric water heater (Geyser) provided by the department (old & new) against the taking down under respective items. Cost of additional wire & lugs shall deemed included in quoted rates.

Deduction to be made from BOQ for Sch 'A' Part -II (Schedule of credit) Amount of Rs. 3,77,203.10 during AOC. Note: Tenderers shall not quote for this schedule.

M/S MOHAN LAL SHARMA (BID ID -3285040)

bamral builder (BID ID -3285246)

R.K. Works (BID ID -3285050)

ASHOK KUMAR SHARMA (BID ID -3285512)

SHARMA CONSTRUCTION COMPANY (BID ID -3284097)

RAJINDRA ENGINEERS & CONTRACTORS (BID ID -3285261)

vijay builders (BID ID -3285403)

M/s Khajuria Construction Co. (BID ID -3285355)