ADDN/ALTN OF RAMP AND PROVISON OF STAND BY POWER SUPPLY TO POL STORE (MT SECTION) FOR KERB SIDE PUMP AT AF STN HASIMRA

Amount

Taking down cement plaster on brick or concrete surfaces including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed..

Demolition of bricks work or stone/boulder masonary, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stonework and precast concrete aritcles, complete all as specified and directed.

M&L for brick work with fly ash bricks, old size, straight or curved on plan exc 6 mtr mean radius built in CM (1:6), complete all as specified and directed.

M & L for rendering 15mm thick (10mm + 5mm) in two coats on fair faces of brick work or concrete surfaces of wall in CM (1:4), mixed with integral water proofing compound at top layer as per manufacturer's instructions and finished the surface even and fair without using extra cement, complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item as supply only.)

Supply only liquid water proofing compound conforming to IS: 2645 - 1975 specification, complete all as directed

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash, complete all as specified and directed.

Surface dressing not exceeding 15cm deep in soft/loose soil, complete all as specified and directed.

Excavation in trenches n. exc. 1.5m wide and n. exc. 1.5m in deep for foundation etc. or for shaft, wells, cesspits, manhole, pair house or for foundation of pole/stay etc. n. exc. 10 Sqm on plan and getting out in soft/loose soil, complete all as specified and directed.

Returning filling in incl spreading, leveling watering and well ramming in layers not exceeding 25cm in soft/loose soil, complete all as specified and directed.

Removing excavated materials to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point in any type of soil, complete all as specified and directed.

M&L for bringing River Bed Materials (RBM) mixture of natural sand, gravel, crushed stone from outside MoD land and depositing where directed at a level n. exc 1.5 mtr above the starting point including raising (or lowering) RBM, spreading in layers n. exc. 30cm thick watering, ramming and consolidating, complete all as specified and directed.

M & L for PCC (1:3:6) type C2 (using 40mm graded crushed stone aggregate) for foundation, filling, mass concrete etc, complete all as specified and directed.

M&L for hardcore of gauge not exceeding 63mm using broken stone or boulders, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface, complete all as specified and directed. (Note : Compacted thickness shall be measured for payment.)

Demolition of reinforced cement concrete(reinforcement cut as required to facilate demolition) of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

M&L for 100mm thick PCC (1:2:4) type B- 2 (using 40mm graded crushed stone aggregate) as in floors & pavings, path, hard standing etc, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 80mm thick factory made chamfered edge pre-cast cement concrete paver block of M-40 factory made, grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

M&L for PCC (1:2:4) type B1 (using 20mm graded crushed stone aggregrate) as in roof kerbs or mud stops, coping etc., rounded or chamfered on edges, complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof coverings, complete all as specified and directed.

S&F pre painted galvalume aluminium zinc coating, GI based corrugated steel sheet 0.50mm thick, of any colour, having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws, complete all as specified and directed.

S&F pre painted galvalume aluminium zinc coating, GI based plain steel sheet 0.50mm thick, of any colour, having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws, complete all as specified and directed.

S&F roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel ,rolled section or flat sections) of Fe-290, E-265 including distance pieces, cleats etc, complete all as specified and directed.

M&L for prepartion of new steel or iron surfaces of any description over 10cm width or girth not otherwise described and applying of two coats of synthetic enemel paint (1st grade quality) over a coat of red oxide primer, complete all as specified and directed.

Supply, laying, jointing and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70 Sqmm 3.5 core including taking down old unserviceable UG cable of any description, complete all as specified and directed.

All as per item No. 23.00 here-in-before but cross sectional area 16 Sqmm 4 core, complete all as specified and directed.

All as per item No. 23.00 here-in-before but cross sectional area 10 Sqmm 4 core, complete all as specified and directed.

Supply & laying double walled corrugated (DWC) HDPE duct pipe of 40mm dia conforming to IS approved colour complete with fittings for cable protection, complete all as specified and directed.

Supply, filling in trenches, spreading, leveling sand cushioning 8cm below cable and 15cm above the cable punned down to 18cm for under ground cable, complete all as specified and directed. (Note : Punned thickness shall be measured for payment)

M&L for sub class ‘B’ old size bricks, burnt clay bricks, laid flat, dry in trenches for cable protection, complete all as specified and directed.

Supply, fabricating, installing, testingng and commissioning of outdoor type LT feeder pillar box of suitable size factory fabricated, cubical panel, wall/floor mounted single door, dust and vermin proof CPRI approved made out of 3.15mm thick CRCA sheet alongwith both side cable alley of width not less than 200mm each side for termination of cable with provision for top and bottom cable entry mounting on 50 x 50 x 5mm Angle iron supports at the base duly painted with synthetic enamel paint and panel board with front and back opening and locking arrangement compete including finishing with two coats of powder coated paint of approved shade over one coat of red oxide zinc chrome primer including all busbar of copper bus bar strip 40mm x 10mm for three phase 4 wire 415 Volts, 50 Hz, AC supply including suitable size copper conductor control wiring, necessary cable glands, lugs etc, proper arrangement for ventilation with and including the following accessories including taking down old unserviceable LT panel/feeder pillar box of any size : INCOMING: (i) MCCB 200 Amps, AC 4 pole 415 Volt 36 KA Breaking Capacity thermal magnetic release range 200-250A, with suitable rotary extendable handle for operation of MCCB-01 No. OUTGOING: (i) MCCB 100 Amps, AC 4 pole 415 Volt 25 KA Breaking Capacity thermal magnetic release range 80-100A, with suitable rotary extendable handle for operation - 03 Nos (02 working & 01 spare) (ii) MCCB 63 Amps, AC 4 pole 415 Volt 25 KA Breaking Capacity thermal magnetic release range 63-80A, with suitable rotary extendable handle for operation - 03 Nos (02 working & 01 spare) (iii) Isolator 04 pole 80 Amp - 04 Nos (iv) MCB SBN 63 Amp 'B' curve, 10 KA - 08 Nos (v) Digital voltmeter with all accessories for incoming (vi) Digital ammeter with all accessories for incoming & each outgoing (vii) Phase indicating lamp LED Type (R-Y-B) for incoming and each outgoing connections

M&L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6.0mm thick buried directly in ground vertically to a depth not less than 2.25 meter below ground level with top edge of earth plate at a depth not less than 1.5 meter below ground level, earth plate surrounded by 15cm thick packed layer of charcoal dust and common salt, connected to galvanized iron strip 25mm x 4mm thick as earth lead by means of bolts, nuts and washers of galvanized iron or steel and thimbles and other end of the earth strip connected to earthing test point/equipment and protected by galvanized iron pipe, light grade, 40mm bore, up to earthing test point/equipment fixed with required number of mild steel clamp made out of 25mm x 3mm flat iron and perforated water pipe 20mm dia. GI medium grade of length 2.25 meter and top with socket & plug and bottom connected to earth plate by slit and two bolts/nuts/washers, PCC chamber in cement concrete (1:2:4) type B-1 and 40mm thick pre-cast RCC (1:2:4) type B-0 cover with 40mm x 40mm x 6mm MS angle iron frame, excavation & earth work complete all as shown in electrical plate No. 3 of MES Schedule Part-I of SSR-2009, complete all as specified and directed.

Supply, fabricating. installing, testinging and commissioning of outdoor type LT feeder pillar box of suitable size factory fabricated, cubical panel, wall/floor mounted single door, dust and vermin proof CPRI approved made out of 3.15mm thick CRCA sheet alongwith outer portion AC 415 volts, 50 Hz of size 600mm x 400mm x 300mm mounting on PCC foundation and inner portion of size 2.0mm thick suitable size of MS channel including suitable size copper conductor control wiring. necessary cable glands, lugs etc. proper arrangement for ventilation with and including the following accessories including taking down old unserviceable LT panel/feeder pillar box of any size:- INCOMING:- (i) MCCB 100 Amps, AC 4 pole 415 Volt 25 KA Breaking Capacity thermal magnetic, with suitable rotary extendable handle for operation - 01 No OUTGOING:- (i) MCCB 63 Amps, AC 4 pole 415 Volt 36 KA Breaking Capacity thermal magnetic, with suitable rotary extendable handle for operation- 02 Nos. (ii) Panel mounted astronomical timer with automatic on-off through 65 Amp TP contactor & by pass function 63 Amp MCB TP for manual on-off - 02 Nos (one woking and one stand by) (iii) Phase indicating lamp LED Type (R-Y-B) for incoming and each outgoing connections (iv) Digital voltmeter with all accessories -01 No. (v) Digital ammeter with all accessories -01 No. (vi) Copper busbar 3 phase 4 wire for wire for rating 400 Amps (40 x 10mm) for phase and neutral - 04 Nos.

S&F KIOSK box weather proof made out of PVC and including made out of one piece mounted SMC base and door pole mounted hinged door size 333 x 233 x 200mm out side and 300 x 200 x 105mm inside dimension comprising of aluminum bus bar 4 strips for 3 phase and neutral 63 Amp and 10 Amp MCB for controlling the street light fitting including Fl clamps 30 x 4mm with necessary MS bolts and washer including notice of size not embossing/painting of danger notice of size not less than 10cm x 7.5cm with letters, figures and conventional skull and bones in signal red colour on front face of KIOSK box body, complete all as specified and directed. Make: Sintex Cat Part No GS JB 3020 or equivalent in Finolex/Universal Switch gear

S & F cable 3 core FR PVC insulated round sheathed copper conductor of size 1.0 Sqmm for connection etc, complete all as specified and directed.

Horizontal boring under the road/pavment/hardstanding (with manual method) below 1mtr from the road surface and dia of hole not exc 100mm, with out damaging the existing road, getting out and disposal of soil to a distance not exceeding 50m from the site of work and making good both the ends, complete all as specified and directed.

M&L for 40mm bore GI tubing, light grade, with necessary fittings for cable protection, laid in trenches, complete all as specified and directed.

Note: An amount of Rs 4750.00 on account of Credit Schedule for schedule 'A' part - II shall be deducted from the total amount of BOQ to arrive at the contract sum.

BHARAT ELECTRIC (BID ID -3140715)

M/S ROY ENTERPRISE (BID ID -3140734)

SHRI PARTHA DUTTA (BID ID -3140695)

M/S RATHIN ENTERPRISES (BID ID -3140128)

M/S. NARENDRA KUMAR GARG (BID ID -3140691)

Hanuman Prasad Agarwal (BID ID -3140701)

M/S BISHAL ENTERPRISES (BID ID -3140744)