Construction of Regional Disease Diagnostic lab at Leh

Earth work in excavation by mechanical means (Hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

Supplying and fixing MS angle brackets, hangers, supports as per detail drawing for supporting soil, waste and rain water pipes with suitable GI U clamps, bolts, nuts and washers etc. The clamps shall be painted with two coats of enamel ( approved ) paint over a coat of primer etc, Coplete.

Constructing masonry Chamber 30x30x50 em, Inside with 75 class designation brick work in cement mortor 1:4 ( 1 Cement : 4 coarse sand ) for stop cock, with C.I surface box 1 00 x1 00x75 mm ( inside ) with hil 1 yea C: Iver fixed in Cement concrete slab 1:2:4 mix ( 1 cement :2 Coarse Sand: 4 excavation, foundation concrete 1:5"10 ( 1 Cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 ( 1 Cement : 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design. with cement conc solid block 1:3:6

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form work for : Foundations, footings, bases for columns

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Cement concrete flooring 1:2:4 ( 1 Cement : 2 Coarse Sand : crushed stone aggregate ) with a floating coat of neat cement slurry but excluding cost of nosing of steps etc. Complete 50mm thick with 20mm nominal ( complete job including carriage )

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Ordinary rock

Dumping Stone including cost of stone horizontal level.

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diaMetre bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Circular shape 453x357mm

Providing and fixing heat tape 33 watts of multi layer including wiring over pipe line in spring shape all complete job. Denfos or chromolex

Providing & fixing upto floor five level precast cement concrete solid blocks including hoisting and setting in position in cement mortar 1:3:6 (1cement:3 coarse sand , 6 graded stone aggregate 20mm nominal size inc cost of required centring, shuttering and curing complete

Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete : 100x58x1.90 mm

Providing and fixing aluminium tower bolts ISI marked (anodised anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour of shade with necessary screws etc complete:

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete.

Providing and fixing aluminum hanging floor door stopper, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : Single rubber stopper

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profilesduly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriatedimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated)casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plasticcaps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusionwelded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixinghardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wallshall be filled with weather proof silicon sealant over backer rod of required size and of approved quality,all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes andsilicon sealant shall be paid separately). Variation in profile dimension in higher side shall be acceptedbut no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth& width of profile shall be acceptable.uPVC profile should be tested by BSI(UK) & SKZ(Germany) @25000 weathering hours Casement window single panel with S.S. friction hinges (400 x 19 x 1.9 mm) made of (big seriesframe 67 x 60 mm & sash 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 0.75 sqm.) Preferable brand shall be Fenesta/Arco-Kommerling as per the details attached,

Providing and fixing Aluminum work for doors, windows, ventilators etc with extruded builtup standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS 733 and IS 1285, fixed with rawlplugs and screws incl necessary filling up of gaps at junctions, at tops, bottoms and sides with required PVC / neoprene felt etc.all complete as per directions of Engineer I/C (glazing and panelling to be paid for separately.) FOR fixed portion, Powder Coated aluminum (minimum thickness of Powder coated 50 microns)

Providing and fixing Aluminum work for doors, windows, ventilators etc with extruded builtup tubular sections / appropriate Z sections and other sections of approved make conforming to IS 733 and IS 1285, fixed with rawlplugs and screws incl necessary filling up of gaps at junctions, at tops, bottoms and sides with required PVC / neoprene felt etc.all complete as per directions of Engineer I/C (glazing and panelling to be paid for separately.) FOR shutters of doors, windows and ventilators including P/F hinges / Pivots and making provision for fixing of fittings wherever required including cost of PVC / neoprene gasket required (Fittings shall be paid separately.) Powder Coated aluminum (minimum thickness of Powder coated 50 microns)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with with water proofing cement compound @ 0.253kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm . This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.The rate includes reparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Providing and fixing Ist quality ceramic glazed tiles conforming to IS:15622 of minimum thickness 9mm of approved make like NITCO. ORIENT, SOMANY, KAJARIA or equivalent make in all colour, shades except begundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados(walls) over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slury @ 3:3 Kg per Sqm including pointing in white cement mixed with pigment of matching shade complete. including carriage of material.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Medium shade pigment using 50% white cement 50% Grey cement (Ramp)

Providing and laying gang saw cut of specified thickness, mirror polished pre- moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations(kitchen, washroom counters, stairs etc) , laid over 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in- Charge. (Granite work) 18 mm thick

Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. (Granite Work Double Edge)

15mm thick cement plaster on the rough side of single or half brick wall of mix 1:6 (1 cement :6 fine sand)

Rough cast plaster upto 10 m height above ground level with a mixture of sand and gravel or crushed stone from 6 mm to 10 mm nominal size, dashed over and including the fresh plaster in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) and top layer 10 mm cement plaster 1:3 (1 cement : 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement. Ordinary cement finish using ordinary cement

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

Finishing wall with water proffing cement paint of required shade on new work (two or more coat applied 3.84kg/10sqm )

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the wall surface to prepare the surface even and smooth complete. ( 2mm Thick). Complete job

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimetre channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimetre of ceiling fixed to wall/partition with the help of rawl plugs at 450

mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimetre channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimetre channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated areawith perforation size and pattern as approved by the Engineer-in-charge and as per manufacturer'sspecification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.61

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/ liter of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. (Two Coats)

Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on new work

Supply and installation of satin finish stainless steel AISI 304 stainless steel handrail and balustrade system having 38mm dia (2") tube handrail (1.5mm gauge) weight 3.7 kg, erected with chemical grout to be fixed on the top of slab/skirting (Spigot Fixed) at max c/c distance of 600mm complete with all necessary bends and terminations complete, with cover plate, fixings, end terminations, custom bends, as manufactured by Dline or approved equivalent. Height shall be 1050 mm above the finished skirting level complete as per architectural drawings (including cost of all material, leads, lifts and carriages etc upto site of work complete). ( On both sides and along the landing as well)

Providing and fixing traditionally carved wood work (Shingstak) over doors and windows including all accessories as per the direction of the Engineer in-charge, complete with; 2nd class kail wood

French spirit polishing with Two or more coats on new works including a coat of wood filler

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. (Firs Class kail Wood)

Providing and laying 200mm thick mud pushka over talboos with 5mm thick dry grass (Yakzes/spoto/dry paddy straw etc), including ramming at OMC (over Ceiling)

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :Stainless Steel AISI-304(18/8) Orissa pattern W.C. pan of size 585x480 mm with flush pipe and integrated type foot rests.

supply& fixing of brass 2 in 1 Bib cock confirming to IS standards

Providing and fixing toilet paper holder : C.P. brass

Supply & fixing of CP Brass Health faulet in chrome finish with flexible pipe with spray head and wall hook confirming to IS standard.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps.

Providing and fixing CP Brass pillar tap.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing Twin Robe Hook

Providing and fixing Liquid Soap Dispenser

Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink with drain board 17.10.1.1 510x1040 mm bowl depth 250mm.510x1040 mm bowl depth 178mm.

Supply & fixing of single lever sink cock

Supply & fixing of Long body Bib cock

Supply & fixing of Stainless Steel Circular grating with upvc floor Trap of approved make - For Toilets & Kitchen.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15mm nominal bore.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15mm nominal bore.

Supplying, fixing & Testing of Fancy Type cp Brass Bottle Trap for wash Basins .

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15mm nominal bore.

Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length 15 mm nominal bore

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes SDR 7.4 U V stabilized & anti -microbial fusion welded, having thermal stability for hot & cold water supply including all PP - R plain & brass threaded polypropylene random fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineer in Charge. (Internal workexposed on wall) PN-16 Pipe, 16 mm OD

PN - 16 Pipe, 20mm OD (SDR-7.4)

PN - 16 Pipe, 25mm OD (SDR-7.4)

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes SDR 7.4 U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Chajge. (Concealed work including cutting chases and making good the walls etc.,) PN-16 Pipe, 32 mm OD (SDR-7.4)

PN - 10 Pipe, 75mm OD (SDR-11)

PN-16 Pipe, 40 mm OD (SDR-7.4)

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes SDR 7.4 U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings i/c trenching .refilling & testing of joints complete as per direction of Engineer in Charge. (External work) PN-10 Pipe, 50 mm OD

Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately): 80 mm dia nominal bore

Supply , fixing , testing & commissioning of 25mm thick foam insulation insulation Endura Maxx circular water tank 5000 litres.

Providing and fixing 100mm pine wood plain lining tongued and groved including wooden plugs complete with necessary screws and priming coat on enexposed surface 10mm thick. Complete job.

Providing and fixing of Puff insualation including covering with wire meshing and aluminium sheet of 0.6mm thick complete job.

Providing and fixing thermocold fex over pipe line for insulation all complete job.

Supplying and fixing in position p.c.c pedestals 300mmx300mmx150mm with MS brackets & GI clamps for laying pipes on terrace.

Supplying , Fixing, Testing & Commissioning of SWR PVC Pipe, Single Socke

ted, in any length with rubber ring joints- fixed to Walls 110mm dia

75mm dia in Walls & on wall

50mm dia in walls & on Walls

40mm dia- in walls & on wall

Supplying , Fixing , Testing & Commissioning of PVC Vent cowls 50mm

Supplying , fixing , Testing& Commissioning of Rain water PVC Pipe, including fittings shall be unplasticized Rigid UPVC rain water pipes conforming to IS : 13592 Type A along with all bends, elboes. Tee, Y etc exposed on wall/ in the shafts. 110 mmm

Supplying , Fixing Testing & commissioning of Rain water 110mm Khurra.

Providing and fixing PTMT grating of approved quality and colour. Circular type 125 mm nominal dia with 25 mm waste hole.