ADDITION/ALTERATION AND IMPROVEMENT TO SEWAGE SYSTEM AND GREASE TRAP AT AFAC COIMBATORE

Amount

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Demolition of unreinforced cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

All as per item No 2 above but reinforced cement concrete (Manhole Cover) complete all as specified and as directed.

Demolition and breaking up drain pipes of 150 mm internal dia (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, ceilings, etc including racking out Joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.

Excavation in trenches n.exc 1.50 metre wide and n.exc 1.5 metre deep for foundation or for shafts, wells, cesspits, manholes, pier holes not exceeding 10 Sqm on plan and getting out in any type of soil complete all as specified and as directed.

All as per Item No:6 described here in before but depth exceeding 1.50 m and not exceeding 3 .00 m complete all as specified and as directed.

All as per Item No:6 described here in before but depth exceeding 1.50 m and not exceeding 3 .00 m in soft/ disintegrated rock complete all as specified and as directed.

M&L PCC 1:3:6 type C-2 using 40 mm gradded crushed stone aggregate in foundation filling/bed complete all as specified and as directed.

M&L for Pre cast cement concrete block masonary with solid blocks exc 10 cm in width in PCC 1:2:4 type B-1 using 20 mm graded stone aggregate and setting in CM 1:4 complete all as specified and as directed.

M&L, MS rungs fixed in concrete conforming to Fe-290 Gde E 165 complete all as specified and as directed.

M & L Precast reinforced cement concrete 1:1.5:3 type A1 using 20 mm graded stone aggregate as in slab over manhole set in CM 1:4 including fixing of Manhole cover frame complete all as specified and as directed.

M&L, MS TMT bars 10 mm dia and over as in reinforcement cut to length bent to shape required including bending, cranking and hooking ends and binding with and including MS Wire (annealed) not less than 0.90 mm dia complete all as specified and as directed.

S&F 600 x 600 mm FRP Manhole cover with frame to with stand load 5MT, all as specified and directed. Make : Prince (DURAFIT) or equivalent complete all as specified and as directed.

S&F 600 x 600 mm FRP Manhole cover with frame to with stand load 40MT, all as specified and directed. Make : Prince (DURAFIT) or equivalent complete all as specified and as directed.

M & L PCC 1:2:4 type B1 using 20 mm graded stone aggreate as in surface channels and drains complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms , moulds , mitred / stopped ends etc., complete all as specified and as directed.

Rendering 20 mm thick in CM 1:3 on fair faces of brick wall or concrete surfaces using WPC finished even and smooth without using extra cement complete all as specified and as directed.

Supply only Integral Water Proofing Compound complete all as specified and as directed.

M&L PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate as in concrete bedding to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe complete all as specified and as directed.

M&L PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate as in concrete bedding to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete for 200 mm bore pipe complete all as specified and as directed.

S&F 150mm inner dia HDPE DWC( Double wall corrugated) Pipe manufactured according to IS:16098 and SN 8 stiffness class, laid and jointed with coupler with elastomeric sealing ring all as specified and directed. Make : Prince (COREFIT) or equivalent complete all as specified and as directed.

S&F 200mm inner dia HDPE DWC( Double wall corrugated) Pipe manufactured according to IS:16098 and SN 8 stiffness class, laid and jointed with coupler with elastomeric sealing ring all as specified and directed. Make : Prince (COREFIT) or equivalent complete all as specified and as directed.

Returning , filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soil complete all as specified and as directed.

Removing excavated material exc 1.50 Km and not exc 5.00 Km out side the MD land including loading and unloading etc., where responsibility regarding place of deposition and obtaining permission from all authorities etc., in this regard will be of contractor complete all as specified and as directed.

Removing building material exc 1.50 Km and not exc 5.00 Km out side the MD land including loading and unloading etc., where responsibility regarding place of deposition and obtaining permission from all authorities etc., in this regard will be of contractor complete all as specified and as directed.

Cutting in to existing MH for connecting new drain, making goods to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 using 20mm graded stone aggregate, smooth finished and reforming benching as required for internal diameter of pipe 150mm complete all as specified and as directed.

Cutting in to existing MH for connecting new drain, making goods to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 using 20mm graded stone aggregate, smooth finished and reforming benching as required for internal diameter of pipe 200mm complete all as specified and as directed.

S&F for PVC (SWR) 110mm dia pipes single socketed, in any length with rubber ring joints, fixed to walls including dismantling old PVC pipes complete all as specified and as directed.

S&F PVC (SWR) couplers 110 mm, setting and jointing with solvent cement complete all as specified and as directed.

S&F PVC (SWR) bend 110 mm, setting and jointing with solvent cement complete all as specified and as directed.

S&F PVC (SWR) branch piece 110 mm, single T equal or unequal with access cover, setting and jointing with solvent cement complete all as specified and as directed.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement including dismantling old gully trap complete all as specified and as directed.

S&F PVC (SWR) reducers 110 mm, setting and jointing with solvent cement complete all as specified and as directed.

S&F for PVC (SWR) 75mm dia pipes single socketed, in any length with rubber ring joints fixed to walls including dismantling old PVC pipes complete all as specified and as directed.

S&F PVC (SWR) couplers 75 mm, setting and jointing with solvent cement complete all as specified and as directed.

S&F PVC (SWR) bend 75 mm, setting and jointing with solvent cement complete all as specified and as directed.

S&F PVC (SWR) branch piece 75 mm, single T equal or unequal with access cover, setting and jointing with solvent cement complete all as specified and as directed.

S&F PVC (SWR) vent cowl 110 mm, setting and jointing with solvent cement complete all as specified and as directed.

M & L soling for sub base with broken boulders or quarried stone of 200mm thickness complete all as specified and as directed.

M&L for 150mm thick WBM (compacted thickness)(laid in two layers of each 75mm) ,with coarse agreggate(Kankar) of grading 3 (50 to 20mm size). Spread rolled and consolidated to gradient and camber required complete all as specified and as directed.

M& L for applying evenly a priming/ tack coat with cationic bituminous emulsion SS-1 conforming to IS-8887 @ 7.5 kg/10 Sqm on new WBM surface all as specified and directed.

M&L for Bituminous premixed carpet 30mm consolidated thickness, with 0.405 cum of stone chipings mixed with 21.9 kg of binder(Paving bitumen VG-30), rolled and compacted to required camber and gradient complete all as specified and as directed.

M & L PCC 1:4:8 type D2 using 40mm graded stone aggregate as in filling and mass concrete complete all as specified and as directed.

M & L cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in filling and mass concrete complete all as specified and as directed.

Dismantling of stone sett paving of any description, laid dry complete all as specified and as directed.

M&L Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M & L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658 -2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and as directed.

All as in item No.48 above but except existing paver block complete all as specified and as directed.

M&L Screed bed or bedding layer of mortar 20 mm thick for laying floor finishes in CM 1:6 complete all as specified and as directed.

M & L Chequered cement concrete tiles 300 x 300 x 25 mm thick with grey cement and pigment, set, jointed and pointed in neat cement slurry in floors complete all as specified and as directed.

M & L precast cement concrete solid building blocks exc 10 cm thick in type C1 1:3:6 (20mm graded aggregate) and set in cement mortar 1:4 complete all as specified and as directed.

M & L PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in coping including necessary formwork complete all as specified and as directed.

Rendering 10mm thick on brick or concrete surface in CM 1:4 and finished even & fair complete all as specified and as directed.

M & L preparation of newly plastered surfaces of any description over 10cm in girth or width and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and as directed.

Supply and replace galvanised steel tubing medium grade 50mm bore dia including fittings complete all as specified and as directed. (Make: TATA/JINDAL/Zenith)

Supply and replace galvanised steel tubing medium grade 80mm bore dia including fittings complete all as specified and as directed. (Make: TATA/JINDAL/Zenith)

Suply and fixing for straight through cable joining kit heat shrinkable type joint for 1100 volts grade cable complete with jointing material and accessories suitable for 305/4 core XLPE/PVC insulated armoured aluminium conductor cable for the size 70 to 150 sqmm all as specified and directed MAke: Raychem, M seal, Denson etc.

P Natesan and Co

PRAGATHI BUILDERS

Lucky Enterprises

devan enterprises