Renovation of training centre rooms, dining hall, kitchen, external facade and gate at L and D centre NALCO.

NAME OF WORK :- Renovation of Training Centre Rooms, Dining Hall, Kitchen,

External Facade and Gate at L&D Centre NALCO, Bhubaneswar

ABSTRACT OF COST OF TRAINING HALL ROOMS (G+1)

Sl. Description DSR Anount Amount on

No. (In Rs.) Non- DSR

1 COST OF CIVIL WORK 29,79,075.58 64,03,191.48

2 COST OF PLUMBING WORK 4,98,483.31 3,21,244.00

3 COST OF ELECTRICAL WORK 3,47,452.06 1,69,803.00

Digitally signed by JAYA

NAME OF WORK :- Renovation of Training Centre Rooms, Dining Hall, Kitchen, External Facade and Gate at L&D Centre NALCO, Bhubaneswar

BILL OF QUANTITY ( TRAINING HALL ROOMS (G+1) 24 ROOMS+ 1 No Office )

Sl. DSR-2019 Description Qty Unit DSR-Rate Non-DSR Rate Amount On Amount On

No. (In Rs.) (In Rs.) DSR-2019 Non- DSR

DEMOLISHING WORK

1 15.12 Dismantling doors, windows and clerestory windows (steel or wood) shutter

including chowkhats, architrave, holdfasts etc. complete and stacking within

50 metres lead :

15.12.1 Of area 3 sq. metres and below 100.00 Each 289.21 28,920.54

2 15.17 Dismantling steel work in single sections including dismembering and

stacking within 50 metres lead in:

15.17.2 Channels, angles, tees and flats 208.00 Kg 1.79 372.54

3 15.23 Dismantling tile work in floors and roofs laid in cement mortar including

stacking material within 50 metres lead.

15.23.1 For thickness of tiles 10 mm to 25 mm 653.13 Sqm 57.79 37,743.33

4 15.56 Dismantling old plaster or skirting raking out joints and cleaning the surface

for plaster including disposal of rubbish to the dumping ground within 50

metres lead. 146.52 Sqm 41.09 6,020.40

5 15.60 Disposal of building rubbish / malba / similar unserviceable, dismantled or

waste materials by mechanical means, including loading, ransporting,

unloading to approved municipal dumping ground or as approved by

Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts

6 13.91 Removing dry or oil bound distemper, water proofing cement paint and the

like by scrapping, sand papering and preparing the surface smooth

including necessary repairs to scratches etc. complete. 1104.84 Sqm 19.23 21,243.51

7 14.1 Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.

meters and under, including cutting the patch in proper shape, raking out

joints and preparing and plastering the surface of the walls complete,

including disposal of rubbish to the dumping ground, all complete as per

directions of Engineer-In-Charge.

14.1.2 With cement mortar 1:4 (1cement: 4 coarse sand) 75.24 Sqm 452.61 34,054.70

8 9.1.1 Providing wood work in frames of doors, windows, clerestory windows and

other frames, wrought framed and fixed in position with hold fast lugs or

with dash fasteners of required dia & length (hold fast lugs or dash fastener

shall be paid for separately).

Second class teak wood 1.46 Cum 137157.14 2,00,249.43

9 9.21 Providing and fixing ISI marked flush door shutters conforming to IS : 2202

(Part I) non-decorative type, core of block board construction with frame of

1st class hard wood and well matched commercial 3 ply veneering with

vertical grains or cross bands and face veneers on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with

necessary screws 52.92 Sqm 1987.77 1,05,192.96

10 9.23 Extra for providing lipping with 2nd class teak wood battens 25 mm

minimum depth on all edges of flush door shutters (over all area of door

shutter to be measured). 52.92 Sqm 422.90 22,380.06

11 9.40.1.2 Providing and fixing wooden moulded beading to door and window frames

with iron screws, plugs and priming coat on unexposed surface etc.

2nd class teak wood

12 9.53 Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame

with 10 mm diameter bolts, nuts and wooden plugs and embedding in

cement concrete block 300x100x150mm 1:3:6 mix (1 cement : 3

coarse sand : 6 graded stone aggregate 20mm nominal size).

13 9.71 Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy

weight) with stainless steel screws etc. complete :

14 9.84 Providing and fixing aluminium extruded section body tubular type universal

hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on

the body, door weight upto 36 kg to 80 kg and door width from 701 mm to

1000 mm), with double speed adjustment with necessaryaccessories and

screws etc. complete. 25.00 Each 897.22 22,430.54

15 9.101 Providing and fixing aluminium hanging floor door stopper ISI marked

anodised (anodic coating not less than grade AC 10 as per IS : 1868)

transparent or dyed to required colour or shade with necessary screws etc.

9.101.2 Twin rubber stopper 75.00 Each 65.37 4,903.06

16 9.127 Providing & Fixing decorative high pressure laminated sheet of plain / wood

grain in gloss / matt / suede finish with high density protective surface layer

and reverse side of adhesive bonding quality conforming to IS : 2046 Type

S, including cost of adhesive of approved quality.

Digitally signed by JAYA

17 9.165 Providing and fixing bright /matt finished Stainless Steel handles of

approved quality & make with necessary screws etc all complete. (a) 125

18 MR Providing & fixing Stainless steel sliding door bolts ISI marked anodised

(anodic coating not less than grade AC 10 as per IS : 1868) transparent or

dyed to required colour or shade with nuts and screws etc complete. (a)

19 MR Providing and fixing stainless steel towerbolts (barrel type) with necessary

screws etc. complete. -

WPC DOOR FOR TOILETS

20 DSR 2023 Providing and fixing factory made single extruded WPC (Wood Polymer

26.86.5 Composite) solid door/window/Clerestory windows & other

(MR) Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60

(Suspension Grade), calcium carbonate and natural fibers (wood powder/

rice husk/wheat husk) and non toxic additives (maximum toxicity index of

12 for 100 gms) fabricated with miter joints after applying PVC solvent

cement and screwed with full body threaded star headed SS screws having

minimum frame density of 750 kg/cum, screw withdrawal strength of 2200

N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2,

modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class

A category with property of being termite/borer proof, water/moisture proof

and fire retardant and fixed in position with M.S hold fast/lugs/SS dash

fasteners of required dia and length complete as per direction of Engineer-

In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for

Note: For WPC solid door/window frames, minus 5mm tolerance in

dimensions i.e depth and width of profile shall be acceptable. Variation in

profile dimensions on plus side shall be acceptable but no extra payment

on this account shall be made.

21 DSR 2023 Providing and fixing factory made single extruded WPC (Wood Polymer

26.87.2 Composite) solid plain flush door shutter of required size comprising of

(MR.) virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate

and natural fibers (wood powder/ rice husk/wheat husk) and non toxic

additives (maximum toxicity index of 12 for 100 gms) having minimum

density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) &

900 N (Edge), minimum compressive strength 50 N/mm2, modulus of

elasticity 850 N/mm2 and resistance to spread of flame of Class A category

with property of being termite/borer proof, water/ moisture proof and fire

retardant and fixing with stainless steel butt hinges of required size with

necessary full body threaded star headed counter sunk S.S screws, all as

per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and

necessary S.S screws shall be paid separately)

22 MR. System Aluminium Factory made Double Rebate Windows with Grill and

Providing and fixing of A2Z Series Double rebate windows & ventilators

made of High-performance factory-made system Aluminium windows with

Akzonobel powder coating of 60-70 microns (Any RAL Colour). Section for

Outer frame should be of 91mm x 35mm, Glass shutter frame shall be of

54mm x 30mm, Mesh shutter frame shall be of 54mm x 30mm, 5mm thick

Single Glazed beading shall be of 15mm x 18mm. 5mm thick Clear Glass

shall be used in all the windows & ventilators. Stainless Steel Wire Mesh

shall be used in Wire mesh Shutters. 10mm Sq bar M.S. Grill/Guard bar

with 150mm c/c shall be fixed in between glass & mesh shutter. All frame

corners shall be joined/assembled using self-locating corner cleats (No

screwing at corners shall be allowed). All Hardware shall be used from a

reputed brand, weather silicon shall be used for filling the gap between

window opening & window Frame complete in all respect including all taxes.

23 9.134 Providing and fixing wire gauge shutters using stainless steel grade 304

wire gauge with wire of dia 0.5 mm and average width of aperture 1.4

mm in both directions for doors, windows and clerestory windows with

necessary screws :

9.134.1.2.2 35 mm thick shutters.

With ISI marked stainless steel butt hinges of required size.

Kiln seasoned and chemically treated hollock wood. 52.92 sqm 3410.41 3237.00 1,80,478.94

24 Providing and fixing 6mm thick both sides Pre-laminated cement bonded

wood particle board as per IS : 15786:2008 of approved brand and shade

with suitable full threaded steel screws etc. on the backing of racks, drawer,

DSR 9.167 cupboard, kitchen cabinet under kitchen counter etc. all complete as per

(MR) direction of Engineer in-charge. 120.96 SQM 1010.60 1,22,242.18

Digitally signed by JAYA

25 Providing and fixing cupboard shutter with 19mm thick one side decorative

and other side balancing lamination factory pressed BWP grade marine ply

as per IS 710 of approved brand including 2mm thick PVC edge banding

tape with hot glue by edge bending machine etc. with auto closing spring

loaded hinges (hydraulic type) etc. complete as per direction of Engineer in-

harge.(Payment of providing and fixing auto closing hinges shall be paid

26 Providing and fixing 19mm thick both side balancing lamination factory

pressed BWP grade marine ply as per IS 710 of approved brand

boxes,shelves,racks,almirah, cupboard and drawer etc. including

DSR 9.169 necessary nails,screws etc. complete as per direction of Engineer-in-

27 Providing and fixing stainless steel fancy handle of approved make fixed

DSR 2023 with SS screws etc. complete as per direction of Engineer-in-charge.

9.170.1 200 mm for CB

28 Providing and fixing stainless steel soft closing spring hinges at 0 degree

hinges (hydraulic type) of approved make/brand to cupboard shutters with

DSR 2023 full threaded steel screws including making necessary recess in board and

9.171.1 finished etc. complete as per direction of Engineer-in-charge

SS Hanging Rod for CB

29 Providing and fixing 25 mm dia. SS pipe Hanging rods with SS brackets :

30 10.25 Steel work welded in built up sections/ framed work, including cutting,

hoisting, fixing in position and applying a priming coat of approved steel

primer using structural steel etc. as required.

10.25.2 In gratings, frames, guard bar, ladder, railings, brackets,gates and similar

31 10.28 Providing and fixing stainless steel ( Grade 304) railing made of Hollow

tubes, channels, plates etc., including welding, grinding, buffing, polishing

and making curvature (wherever required) and fitting the same with

necessary stainless steel nuts and bolts complete, i/c fixing the railing with

necessary accessories & stainless steel dash fasteners , stainless steel

bolts etc., of required size, on the top of the floor or the side of waist

slab with suitable arrangement as per approval of Engineer-in-charge, (for

payment purpose only weight of stainless steel members shall be

considered excluding fixing accessories suchas nuts, bolts, fasteners etc.).

32 11.55.1 Providing and laying flamed finish Granite stone flooring in required design

and patterns, in linear as well as curvilinear portions of the building all

complete as per the architectural drawings with 18 mm thick stone slab

over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4

coarse sand) laid and jointed with cement slurry and pointing with white

cement slurry admixed with pigment of matching shade including rubbing,

curing and polishing etc. all complete as specified and as directed by the

Engineer-in-Charge :

Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat

Eye or equivalent. 24.06 sqm 2609.12 62,775.35

33 11.56.1 Providing and laying Polished Granite stone flooring in required design and

patterns, in linear as well as curvilinear portions of the building all complete

as per the architectural drawings with 18 mm thick stone slab over 20 mm

(average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid

and jointed with cement slurry and pointing with white cement slurry

admixed with pigment of matching shade including rubbing , curing and

polishing etc. all complete as specified and as directed by the Engineer-in-

34 MR Providing and fixing machine cut, mirror/ eggshell polished , granite work for

wall lining (veneer work) including dado, skirting, risers of steps etc., in

required design and pattern wherever required, stones of different finished

surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3

coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm

including pointing with white cement slurry admixed with pigment of

matching shade, including rubbing, curing, polishing etc. all complete as per

Architectural drawings, and as directed by the Engineer-in-Charge .

Granite of all colour except black, cherry/ruby red 18 mm thick (slab area

above 0.50 sqm).

Digitally signed by JAYA

35 DSR 2023 Providing and laying Vitrified tiles in floor in different sizes (thickness to be

11.41A.1.3 specified by the manufacturer) with water absorption less than 0.08% and

(MR) conforming to IS:15622, of approved brand & manufacturer, in all colours

and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse

sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the

joints with white cement and matching pigments etc. The tiles must be cut

with the zero chipping diamond cutter only . Laying of tiles will be done with

the notch trowel, plier, wedge, clips of required thickness, leveling system

and rubber mallet for placing the tiles gently and easily.

Double charge vitrified tile polished finish of size

Size of Tile 600 x 1200 mm

36 11.46.4 Providing and laying Vitrified tiles in different sizes (thickness to be

specified by manufacturer), with water absorption less than 0.08 % and

conforming to I.S. 15622, of approved make, in all colours & shade, in

skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1

cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm

including grouting the joint with white cement & matching pigments etc.

Size of Tile 1000 x 1000 mm Or 600x1200 mm.

37 11.48.4 Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy

grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of

hardener and 0.20 kg of resin per kg), including filling / grouting and

finishing complete as per direction of Engineer-incharge.

38 DSR 2023 Providing and laying Vitrified tiles in floor in different sizes (thickness to be

11.41A.3.1 specified by the manufacturer) with water absorption less than 0.08% and

(MR) conforming to IS:15622, of approved brand & manufacturer, in all colours

and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse

sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the

joints with white cement and matching pigments etc. The tiles must be cut

with the zero chipping diamond cutter only . Laying of tiles will be done with

the notch trowel, plier, wedge, clips of required thickness, leveling system

and rubber mallet for placing the tiles gently and easily.

Glazed Vitrified tiles Matt/Antiskid finish of size

Size of Tile 600 x 600 mm.

39 MR Providing and fixing Ist quality Glazed vitrified tiles polished finish of size 60

x 120 cm tiles conforming to IS: 15622 (thickness to be specified by the

manufacturer), of approved make, in all colours, shades except burgundy,

bottle green, black of any size as approved by Engineer-in-Charge, in

skirting, risers of steps and dados, over 12 mm thick bed of cement mortar

1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @

3.3kg per sqm, including pointing in white cement mixed with pigment of

matching shade complete. 485.46 SQM 1982.00 9,62,181.72

40 12.45 Providing and fixing false ceiling at all height including providing and fixing

of frame work made of special sections, power pressed from M.S. sheets

and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as

per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm

thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one

flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with

6mm dia bolts, other flange of cleat fixed to the angle hangers of

25x10x0.50 mm of required length with nuts & bolts of required size and

other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9

mm running at the spacing of 1200 mm centre to centre, to which the

ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges

of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall

be fixed in a direction perpendicular to G.I. intermediate channel with

connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every

junction, /window frames, minus 5mm tolerance in dimensions i.e depth

and width of profile shall be acceptable. Variation in profile dimensions on

plus side shall be acceptable but no extra payment on this account shall be

made. screws @ 230 mm interval, including fixing of gypsum board to

ceiling section and perimeter channel with the help of dry wall screws of

size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush

finish of tapered and square edges of the board with recommended jointing

compound , jointing tapes , finishing with jointing compound in 3 layers

covering upto 150 mm on both sides of joint and two coats of primer

suitable for board, all as per manufacturer’s specification and also including

the cost of making openings for light fittings, grills, diffusers, cutouts made

with frame of perimeter channels suitably fixed, all complete as per

drawings, specification and direction of the Engineer in Charge but

excluding the cost of painting with :

I. 12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095-

(Part I) :2011 (Board with BIS certification marks) 437.52 sqm 1177.52 5,15,190.35

II. 12.45.3 12.5 mm thick tapered edge gypsum moisture resistant board. 96.00 sqm 1355.10 1,30,089.94

WALL PANELLING/CLADDING

Digitally signed by JAYA

41 MR Supply and installation of high-quality decorative wallpaper for interior walls.

The wallpaper should be made from durable materials such as vinyl, non-

woven, or paper, with a smooth, consistent texture and design. The

wallpaper should feature a design, pattern, or color scheme as specified in

the project requirements. It must be easy to maintain, resistant to fading,

and suitable for the intended room environment (e.g., living rooms,

bedrooms, offices). Installation includes preparation of the wall surface,

cutting and fitting the wallpaper to size, and ensuring proper alignment of

patterns and seams. The wallpaper should be securely adhered to the walls

using appropriate adhesive, with any excess trimmed neatly, all complete

for all heights as per specifications, drawings and as directed by Engineer-

42 MR Providing and fixing in position factory-finished WPC (Wood Plastic

Composite) Fluted / Louver Wall Panels of approved premium make

(e.g., Alstone, Euro Pratik, or equivalent) and required shade/texture;

specifications including 24mm to 28mm thickness, interlocking tongue-and-

groove profile, minimum density of 0.65 g/cm³, and properties being 100%

water-proof, termite-proof, fire-retardant, and UV-stabilized; scope of work

includes surface preparation of the base wall, supply and installation of

panels using concealed Stainless Steel (SS) clips, screws, and heavy-duty

structural adhesive (PU/Silicon) to ensure a seamless finish, cutting and

mitering of corners at 45 degrees, and fixing of matching end-caps or

start/end profiles; the rate is inclusive of all material costs, labor for

fabrication and installation, hardware, scaffolding (up to 3m), wastages,

taxes, and contractor overheads complete in all respects.

43 13.45 Finishing walls with textured exterior paint of required shade :

13.45.1 New work (Two or more coats applied @ 3.28 ltr/10 sqm)

over and including priming coat of exterior primer applied @

44 13.83 Wall painting with premium acrylic emulsion paint of interior grade, having

VOC (Volatile Organic Compound ) content less than 50 grams/ litre of

approved brand and manufacture, including applying additional coats

wherever required to achieve even shade and colour.

13.50 Applying priming coat :

45 13.50.2 With ready mixed aluminium primer of approved brand and manufacture on

resinous wood and plywood 212.94 Sqm 60.63 12,911.20

46 13.50.3 With ready mixed red oxide zinc chromate primer of approved

brand and manufacture on steel galvanised iron/ steel works 15.50 Sqm 53.42 827.95

47 13.61 Painting with synthetic enamel paint of approved brand and manufacture of

required colour to give an even shade:

13.61.1 Two or more coats on new work 228.44 Sqm 128.06 29,254.39

48 13.65 Painting with black anti-corrosive bitumastic paint of approved brand and

manufacture to give an even shade :

13.65.1 Two or more coats on new work 120.96 Sqm 111.73 13,515.01

49 13.99.1 Painting with synthetic enamel paint of approved brand and manufacture of

required colour to give an even shade:

One or more coats on old work 6.30 Sqm 84.23 530.67

50 13.68.1 French spirit polishing :

Two or more coats on new works including a coat of wood filler 33.26 Sqm 369.96 12,304.92

51 13.71 Lettering with black Japan paint of approved brand and manufacture per

WATERPROOFING WORK

52 22.5 Providing and laying water proofing treatment in sunken portion of WCs,

bathroom etc., by applying cement slurry mixed with water proofing cement

compound consisting of applying : a) First layer of slurry of cement @ 0.488

kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This

layer will be allowed to air cure for 4 hours. b) Second layer of slurry of

cement @ 0.242 kg/sqm mixed with water proofing cement compound @

0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with

water curing for 48 hours. The rate includes preparation of surface,

treatment and sealing of all joints, corners, junctions of pipes and masonry

with polymer mixed slurry.

53 MR Providing and filling AAC (Autoclaved Aerated Concrete) lightweight broken

blocks, including transportation, handling, spreading, leveling, and

compacting in layers to specified thickness, as per drawings and Engineer's

instructions. 20.79 CUM 4132.00 85,904.28

54 2.34 Supplying chemical emulsion in sealed containers including delivery as

specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%. 359.20 Ltr. 211.61 76,010.25

Digitally signed by JAYA

55 2.35 Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL

anti-termite treatment (excluding the cost of chemical emulsion):

2.35.3.1 Treatment of soil under existing floors using chemical emulsion @ one litre

per hole, 300 mm apart including drilling 12 mm diameter holes and

plugging with cement mortar 1:2 (1 cement: 2 Coarse sand) to match the

existing floor:

With Chlorpyriphos/Lindane E.C. 20% with 1% concentration 650.00Sqm 239.21 1,55,488.71

GRAND TOTAL 93,82,267.06

GRAND TOTAL 93,82,267.06

Digitally signed by JAYA

NAME OF WORK :- Renovation of Training Centre Rooms, Dining Hall, Kitchen, External Facade and Gate at L&D Centre NALCO, Bhubaneswar

PLUMBING WORK OF TRAINING HALL ROOMS (G+1)

Sl. DSR- Description Qty Unit DSR-Rate Non-DSR- Amount On Amount On

No. 2019 (In Rs.) Rate DSR-2019 Non- DSR

1 15.42 Dismantling C.I. or asbestos rain water pipe with fittings and

clamps including stacking the material within 50 metres lead

2 15.44 Dismantling G.I. pipes (external work) including excavation

and refilling trenches after taking out the pipes, manually/ by

mechanical means including stacking of pipes within 50

metres lead as per direction of Engineer-in-charge :

15.44.1 15 mm to 40 mm nominal bore 95.00 Mtr 113.94 10,824.66

3 15.45 Dismantling C.I. pipes including excavation and refilling

trenches after taking out the pipes, manually/ by mechanical

means breaking lead caulked joints, melting of lead and

making into blocks including stacking of pipes & lead at site

within 50 metre lead as per direction of Engineer-in-charge:

4 14.82 Dismantling W.C. Pan of all sizes including disposal of

dismantled materials i/c malba all complete as per

directions of Engineer-in- Charge. 1.00 Each 101.14 101.14

5 15.53 Dismantling of C.I. sluice valve including stacking of useful

materials within a lead of 50 metres

15.53.1 Up to 150 mm diameter 4.00 Each 251.86 1,007.43

6 12.41 Providing and fixing on wall face unplasticised Rigid PVC

rain water pipes conforming to IS : 13592 Type A, including

jointing with seal ring conforming to IS : 5382, leaving 10

mm gap for thermal expansion, (i) Single socketed pipes.

7 12.42 Providing and fixing on wall face unplasticised - PVC

moulded fittings/ accessories for unplasticised Rigid PVC

rain water pipes conforming to IS : 13592 Type A, including

jointing with seal ring conforming to IS : 5382, leaving 10

mm gap for thermal expansion.

12.42.1.2 a) Coupler

8 13.96 Painting (one or more coats) on rain water, soil, waste and

vent pipes and fittings with synthetic enamel paint of

approved brand and manufacture and required colour on

13.96.1 75 mm diameter pipes 5.00 Mtr 22.92 114.58

13.96.2 100 mm diameter pipes 10.00 Mtr 29.45 294.47

9 17.78 Providing and fixing white vitreous china extended wall

mounting water closet of size 780x370x690 mm of

approved shape including providing & fixing white vitreous

china cistern with dual flush fitting, of flushing capacity 3

litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat

cover, and cistern fittings, nuts, bolts and gasket etc

10 17.7 Providing and fixing wash basin with C.I. brackets, 15 mm

C.P. brass pillar taps, 32 mm C.P. brass waste of standard

pattern, including painting of fittings and brackets, cutting

and making good the walls wherever require:

17.7.4 White Vitreous China Flat back wash basin size 550x 400

mm with single 15 mm C.P. brass pillar tap. 25.00 Each 2644.94 66,123.46

11 MR Providing & fixing CP brass Overhead shower with shower

arm, Hand Shower 95mm dia Single Lever Concealed

Deusch Mixer with Provision for Connection to Overhead

Shower and Easy flex Tube with accessories complete I all

12 MR Providing and fixing of C. P. brass towel rail 600 x 20 mm

size complete with C.P. brass brackets 25.00 Each 2869.00 71,725.00

13 MR Providing and fixing of C. P. brass towel ring complete with

C.P. brass brackets 25.00 Each 1095.00 27,375.00

Digitally signed by JAYA

14 MR Providing and fixing CP Brass soap dish 109 mm wide,

125 mm high and 112 mm distance from wall of standard

shape with bracket and all fittings of the same material of

approved quality and colour.

15 17.34 Providing and fixing toilet paper holder :

16 MR. Providing and fixing health faucet with 1 m CP brass

flexible tube and swivel hook with CP brass wall flange

including cutting & making good the walls wherever

required complete in all respect as per direction of engineer

17 Providing, fixing, jointing and testing in position of ISI

marked UV stabilized UPVC pipes for soil, waste, and

vent, Type-B as per IS : 13592 suitable for rubber ring

joints, including all neccessary specials and fittings

(confirming to IS:14735) i.e. bends, tees, junctions (with or

without doors), reducers, WC connectors, couplers,

expansion joints / bellows, cowels, clamps, rubber rings,

clean outs etc. fixing at wall/ ceiling/ floor level supported by

clamp & hangers etc. in concealed / inside duct / under floor

& basement ceiling / external work etc. including chase

cutting as required, excavation and back filling in all kind of

soils, suspended from floor under false ceiling or

embedding the pipes laid under floors / building in 75 mm.

alround 1:2:4 cement concrete (1 cement : 2 coarse sand :

4 graded stone aggregate 20 mm nominal size) including

cost of shuttering for proper completion of the work,

breaking and making good the walls and floors etc. after

pipes have been duly laid and tested. The rubber ring shall

confirm to IS:5382.

The Pipes will be supported with threaded G I rods & U

clamps with nuts, washers etc on 50x50x5 mm slotted

angle. The cost will include all support arrangements. The

work includes commissioning of all pipes lines as per

drawings and specifications and as directed by engg-in-

charge at site.

MR 110 mm dia (Wall Thickness - 3.2 to 3.8 mm) 45.00 Mtr 790.18 35,558.04

MR 75 mm dia (Wall Thickness - 3.2 to 3.8 mm) 15.00 Mtr 579.46 8,691.96

18 Providing & fixing UPVC Floor trap of self cleansing design

with stainless steel grating complete in all respects.

MR Multi Floor Trap (5" Ht) with height raiser and branch saddle

strip of 50/75 mm outlet 3.00 Each 673.00 2,019.00

MR Plain Floor Trap (4" Ht) with 50 / 75 outlet and with height

MR P-Trap type Floor Trap 110 x 75 mm 3.00 Each 565.00 1,695.00

19 MR Extra for providing & fixing 125 mm dia C.P. grating in

place of C.I. grating over floor traps. 22.00 Each 597.00 13,134.00

20 MR Providing & fixing of SS Floor Cleanout, round or square

with rubber seal and flat round cover with screws and other

required fitting complete as required. 25.00 Each 389.00 9,725.00

21 17.29 Providing and fixing 100 mm sand cast Iron grating for gully

22 17.31 Providing & fixing 600x450mm bevelled edge mirror of

superior glass (of approved quality) complete with 6mm

thick asbestos cement sheet ground fixed to wooden cleats

with C.P. brass screws and washers. 4.00 Each 1351.78 5,407.14

23 17.35 Providing & fixing soil, waste and vent pipes.

17.35.1.2 a) 100mm dia centrifugally cast iron S & S pipe. 10.00 Mtr 1150.71 11,507.11

17.35.2.2 b) 75mm dia centrifugally cast iron S & S pipe. 5.00 Mtr 1045.20 5,225.98

24 17.37 Providing & fixing M.S. holder bat clamps of approved

design to sand cast iron/centrifugally cast (Spun) iron S & S

pipe embeded in & including cement concrete blocks

10x10x10cm. of 1:2:4 mix (1 cement : 2 coarse : 4 graded

stone aggregate 20mm nominal size). Including cost of

cutting holes & making good the walls etc.

25 17.38 Providing and fixing bend of required degree with access

door, insertion rubber washer 3mm thick, bolts and nuts

17.38.1.2 Sand cast iron S&S as per IS - 3989 4.00 Each 486.38 1,945.53

17.38.2.2 Sand cast iron S&S as per IS- 3989 4.00 Each 405.36 1,621.45

26 17.39 Providing and fixing plain cast iron S & S sanitary bend.

Digitally signed by JAYA

17.39.1.1 Sand cast iron S&S as per IS - 1729 4.00 Each 401.78 1,607.12

17.39.2.2 Sand cast iron S&S as per IS - 3989 4.00 Each 305.27 1,221.09

27 17.43 Providing and fixing single equal plain junction of required

degree with access door, insertion rubber washer 3 mm

thick, bolts and nuts complete.

28 17.56 Providing and fixing cast iron terminal guard.

29 17.57 Providing & fixing cast iron coller.

17.57.1.2 Sand cast iron S&S as per IS - 3989 4.00 Each 431.38 1,725.54

17.57.2 b) 75mm dia.

17.57.2.2 Sand cast iron S&S as per IS - 3989 4.00 Each 270.03 1,080.12

30 17.58 Providing lead caulked joints to sand cast iron/centrifugally

cast (spun) iron pipes & fitting of diameters.

31 17.60 Providing & fixing cast iron trap of self cleansing design with

or without ventarm complete, including cost of cutting &

making good the walls & floors.

32 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, having thermal stability for hot & cold water supply,

including all CPVC plain & brass threaded fittings, i/c fixing

the pipe with clamps at 1.00 m spacing. This includes

jointing of pipes & fittings with one step CPVC solvent

cement and the cost of cutting chases and making good the

same including testing of joints complete as per direction of

Engineer in Charge.

18.8.1 15 mm nominal outer dia Pipes 35.00 Mtr 431.60 15,105.84

18.8.2 20 mm nominal outer dia Pipes 30.00 Mtr 503.77 15,112.96

18.8.3 25 mm nominal outer dia Pipes 20.00 Mtr 592.05 11,841.09

18.8.4 32 mm nominal outer dia Pipes 10.00 Mtr 715.53 7,155.33

33 18.16 Providing and fixing brass stop cock of approved quality.

18.16.1 15 mm nominal bore 4.00 Each 343.94 1,375.75

34 18.17 Providing and fixing gun metal gate valve with wheel of

approved quality.

18.17.1 a) 25mm dia nominal bore 4.00 Each 523.78 2,095.13

18.17.2 b) 32mm dia nominal bore 4.00 Each 612.39 2,449.55

35 18.18 Providing and fixing ball valve (brass) of approved quality

complete. (High or low pressure with plastic floats).

18.18.3 a) 25mm. Nominal bore 4.00 Each 415.11 1,660.43

36 18.21 Providing and fixing 30 cm long unplasticised PVC

connection pipe with brass unions.

18.21.1.1 a) 15mm nominal bore 4.00 Each 76.75 307.01

37 18.21 Providing and fixing 45 cm long unplasticised PVC

connection pipe with brass unions.

18.21.2.1 a) 15mm nominal bore 4.00 Each 87.45 349.79

38 18.49 Providing & fixing CP brass bib cock of approved quality

conforming to IS 8931

18.49.1 a) 15mm nominal bore 4.00 Each 441.39 1,765.58

39 18.51 Providing & fixing C.P. brass long body bib cock of

approved quality conforming to IS standards and weighing

not less than 690 gms.

18.51.1 a) 15mm nominal bore 4.00 Each 581.94 2,327.76

40 18.53 Providing & fixing C.P. brass angle valve for basin mixer

and gyser points of approved quality conforming to IS 8931

18.53.1 a) 15mm nominal bore 8.00 Each 560.50 4,484.00

41 18.53A Providing and fixing C.P. Brass extension nipple (size

15mmx50mm) of approved make and quality as per

direction of Engineer-in-charge. 4.00 Each 64.53 258.13

42 18.75 Providing and fixing PTMT extension nipple for water tank

pipe, fittings of approved quality and colour.

18.75.3 25mm nominal bore, weighing not less than 62 gms 1.00 Each 119.48 119.48

Digitally signed by JAYA

43 18.76 Cutting holes up to 30x30 cm in walls including making

18.76.1 With common burnt clay F.P.S. (non modular) bricks 4.00 Each 344.78 1,379.13

44 18.77 Cutting holes up to 15x15 cm in R.C.C. floors and roofs for

passing drain pipe etc. and repairing the hole after insertion

of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2

coarse sand : 4 graded stone aggregate 20 mm nominal

size), including finishing complete so as to make it leak

45 18.78 Making chases up to 7.5x7.5 cm in walls including making

good and finishing with matching surface after housing G.I.

46 19.26 Raising manhole cover and frame slab to required level

including dismantling existing slab and making good the

damage as required (Raising depth of manhole to be paid

19.26.1 Rectangular manhole 90x80 cm with rectangular cover

47 14.75A Cleaning of terrace/loft water storage tank (inside surface

area) upto 2000 litre capacity at all heights with coconut

brushes, duster etc., removal of silt, rubbish from the tank

and cleaning the tank with fresh water disinfecting with

bleaching powder @ 0.5gm per litre capacity of tank

including marking the date of cleaning on the side of tank

body with the help of stencil and paint and disposing of

malba all complete as per direction of Engineer-in-Charge.

(The old date already written on tank should be removed

with paint remover or black paint and if date is not written

with the stencil or old date is not removed deduction will be

made @ Rs. 0.10 per litre) (if during cleaning any GI fittings

or ball cock is damaged that is to be repaired by contractor

at his own cost and nothing extra will be paid on this

Digitally signed by JAYA

NAME OF WORK :- Renovation of Training Centre Rooms, Dining Hall, Kitchen, External Facade and Gate at L&D Centre NALCO, Bhubaneswar

ELECTRICAL WORK OF TRAINING HALL ROOMS (G+1)

Sl. DSR- Description Qty Unit DSR-Rate NonDSR- Amount On Amount On

No. 2022 (In Rs.) Rate DSR-2022 Non- DSR

1 1.8 Wiring for light point/ fan point/ exhaust fan point/ call bell point

with 1.5 sq.mm FR PVC insulated copper conductor single

core cable in surface / recessed medium class PVC conduit,

with piano type switch, phenolic laminated sheet, suitable size

M.S. box and earthing the point with 1.5 sq.mm. FR PVC

insulated copper conductor single core cable etc as required.

2 1.9 Wiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, 2 way piano type switch,

phenolic laminated sheet, suitable size MS box and earthing

the point with 1.5 sq.mm. FRLS PVC insulated copper

conductor single core cable etc. as required.

3 1.12 Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated

copper conductor single core cable in surface/ recessed

medium class PVC conduit alongwith 1 No 4 sq. mm FR PVC

insulated copper conductor single core cable for loop earthing

as required. 20.00 Mtr 351.89 7,037.86

4 1.14 Wiring for circuit/ submain wiring alongwith earth wire with the

following sizes of FR PVC insulated copper conductor, single

core cable in surface/ recessed medium class PVC conduit as

5 1.15 Rewiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FR PVC insulated copper conductor

single core cable and 1.5 sq.mm. FR PVC insulated copper

conductor single core cable as earth wire in existing surface/

recessed steel conduit including dismantling as required.

6 1.16 Rewiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable and 1.5 sq.mm

FRLS PVC insulated copper conductor single core cable as

earth wire in existing surface/ recessed steel/PVC conduit

including dismantling as required. 8.00 Point 941.89 7,535.14

7 1.17 Supplying and drawing following sizes of FR PVC insulated

copper conductor, single core cable in the existing surface/

recessed steel/ PVC conduit as required.

8 1.21 Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of recessed

conduit as required.

9 1.22 Supplying and fixing metal box of following sizes (nominal size)

on surface or in recess with suitable size of phenolic laminated

sheet cover in front including painting etc. as required.

10 1.29 Supplying and fixing metal box of 150mm X 75mm X 60mm

deep (nominal size) on surface or in recess with suitable size

of phenolic laminated sheet cover in front including providing

and fixing 3 pin 5/6 amps socket outlet and 5/6 amps piano

type switch, connection, painting etc. as required. (For light

plugs to be used in non residential buildings).

Digitally signed by JAYA

11 1.30 Supplying and fixing metal box of 180mm X 100mm X 60mm

deep (nominal size) on surface or in recess with suitable size

of phenolic laminated sheet cover in front including providing

and fixing 6 pin 5/6 & 15/16 amps socket outlet and 15/16

amps piano type switch, connection, painting etc. as required.

12 S/F light plug point Modular type accessories :-

1.31 Supply and fixing of suitable size GI box with modular plate

and cover in front on surface or in recess including providing

and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps.

modular switch, connection etc. as required.

13 S/F power plug point modular type accessories :-

1.32 Supply and fixing of suitable size GI box with modular plate

and cover in FRLSont on surface or in recess, including

providing and fixing 6 pin 5/6 & 15/16 amps modular socket

outlet and 15/16 amps. modular switch, connection etc. as

required. 25 Each 617.39 15,434.82

14 1.33 Supplying and fixing 3 pin, 5 amp ceiling rose on the existing

junction box/ wooden block including connection etc as

required. 25.00 Each 91.66 2,291.52

15 1.34 Supplying and fixing brass batten/ angle holder including

connection etc. as required. 25.00 Each 138.02 3,450.45

16 1.38 Supplying and fixing call bell/ buzzer suitable for single phase,

230 volts, complete as required. 24.00 Each 104.30 2,503.29

17 2.3 Supplying and fixing following way, single pole and neutral,

sheet steel, MCB distribution board, 240 volts, on surface/

recess, complete with tinned copper bus bar, neutral bus bar,

earth bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

2.3.1 6 way, Double door 4.00 Each 2324.18 9,296.71

18 2.4 Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 volts, on

surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without

MCB/RCCB/Isolator)

19 2.10 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts,

"C" curve, miniature circuit breaker suitable for inductive load

of following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

2.10.2 Single pole and neutral 12.00 Each 631.09 7,573.07

2.10.5 Triple pole and neutral 8.00 Each 1293.79 10,350.29

20 2.11 Supplying and fixing single pole blanking plate in the existing

MCB DB complete etc. as required. 12.00 Each 13.70 164.36

21 2.21 Providing and fixing M.V. danger notice plate of 200 mm X 150

mm, made of mild steel, at least 2 mm thick, and vitreous

enameled white on both sides, and with inscription in single red

colour on front side as required. 1.00 Each 283.41 283.41

22 5.2 Earthing with G.I. earth pipe 4.5 Mtr long, 40 mm dia including

accessories, and providing masonry enclosure with cover plate

having locking arrangement and watering pipe etc. with

charcoal/ coke and salt as required. 2.00 Each 7222.23 14,444.46

23 5.12 Providing and laying earth connection from earth electrode with

6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth

electrode including connection with G.I. thimble excavation and

re-filling as required. 10.00 Mtr 302.38 3,023.75

24 5.15 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in

recess for connections etc. as required. 10.00 Mtr 257.07 2,570.71

25 5.16 Providing and fixing 6 SWG dia G.I. wire on surface or in

recess for loop earthing as required. 10.00 Mtr 73.75 737.50

26 1.41 Installation, Testing and Commissioning of pre-wired,

fluorescent fitting / compact fluorescent/ LED fitting of all types,

complete with all accessories and tube/lamp etc. directly on

ceiling/ wall, including connections with 1.5 sq. mm

FRLS/HFFR PVC insulated, copper conductor, single core

cable and earthing etc. as required. 90.00 Each 217.04 Digitally signed by JAYA

27 1.50 Installation of exhaust fan in the existing opening, including

making good the damage, connection, testing, commissioning

etc. as required.

28 NSDR Supply of 15W SURFACE MOUNTED ROUND LED with all

accessories as per standard item.. 26.00 Each 1,345.00 34,970.00

29 NSDR Supply of 20W SURFACE MOUNTED ROUND LED with all

accessories as per standard item.. 25.00 Each 953.00 23,825.00

30 NSDR Supply of 15W WALL BRACKET LED BULB with all

accessories as per standard item. 25.00 Each 378.00 9,450.00

31 NSDR Supply of 20W SURFACE MOUNTED LED TUBE with all

accessories as per standard item. 14.00 Each 897.00 12,558.00

32 NSDR Providing and fixing concealed LED strip lighting in cove/false

ceiling, comprising of high quality flexible LED strip (minimum

9W per meter, warm white/cool white as approved), including

extruded aluminium profile with opal diffuser, complete with

driver (SMPS), connectors, wiring, soldering, fixing inside

ceiling groove, testing and commissioning, complete in all

respects as per direction of Engineer-in-charge.

33 NSDR Supply of AC 230/250 volts, 50 HZ exhaust fans including

providing nuts, bolts, mounting FRLSame and other

accessories etc. complete

Digitally signed by JAYA

NAME OF WORK :- Renovation of Training Centre Rooms, Dining Hall, Kitchen, External Facade and Gate at L&D Centre NALCO, Bhubaneswar

ABSTRACT OF COST FOR FAÇADE STRUCTURE – CIVIL WORKS

[Based on DSR- 2019 ]

Non-DSR- AMOUNT AMOUNT

S.N. DESCRIPTION OF ITEM SCH. NO. QUANTITY UNIT DSR-RATES

RATES DSR ITEMS MR ITEMS

1 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing

in position and applying a priming coat of approved steel primer using structural steel

etc. as required. In gratings, frames, guard bar, ladder, railings, brackets,gates and

2 Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming DSR-13.45.1 141.970 SQM 244.43 34,701.52

coat of exterior primer applied @2.20kg/10 sqm.

3 Providing and applying white cement based putty of average thickness 1 mm, of

approved brand and manufacturer, over the plastered wall surface to prepare the 13.80 141.970 SQM 121.32 17,223.62

surface even and smooth complete.

4 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as

per manufacturer’s specifications including appropriate priming coat, preparation of

surface, etc.complete.

5 Designing, fabricating, testing, installing and fixing in position Curtain Wall with

Aluminium Composite Panel Cladding, with open grooves for linear as well as

curvilinear portions of the building , for all heights and all levels etc. including:

(a) Structural analysis & design and preparation of shop drawings for pressure

equalisation or rain screen principle as required, proper drainage of water to make it

watertight including checking of all the structural and functional design.

(b) Providing, fabricating and supplying and fixing panels of aluminium composite

panel cladding in pan shape in metalic colour of approved shades made out of 4mm

thick aluminium composite panel material consisting of 3mm thick FR grade mineral

core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium

composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF /

Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1

and polymer (Service) coating on face # 2 as specified using stainless steel screws,

nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.

(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised

with serrations and serrated washers to arrest the wind load movement, fasteners, SS

316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent

bi-metallic contacts all complete required to perform as per specification and drawing.

The item includes cost of all material & labour component, the cost of all mock ups at

site, cost of all samples of the individual components for testing in an approved

laboratory, field tests on the assembled working curtain wall with aluminium composite

panel cladding, cleaning and protection of the curtain wall with aluminium composite

panel cladding till the handing over of the building for occupation. Base frame work for

ACP cladding is payable under the relevant aluminium items.

The Contractor shall provide curtain wall with aluminium composite panel cladding,

having all the performance characteristics all complete , as per the Architectural

drawings, as per item description, as specified, as per the approvedshop drawings

and as directed by the Engineer-in-Charge. However, for the purpose of payment, 8.32 1419.770 Sqm 4540.68 64,46,724.29

only the actual area on the external face of the curtain wall with Aluminum Composite

Panel Cladding (including width of groove) shall be measured in sqm. up to two

decimal places.

Providing and fixing double scaffolding system (cup lock type) on the exterior side of

building/structure, upto 25 metre height, above ground level, including additional rows

of scaffolding in stepped manner as per requirement of site, made with 40mm dia

M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup

& lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in

the scaffolding for working platform etc. and maintaining it in a serviceable condition

for execution of work of cleaning and/ or pointing and/ or applying chemical and

removing it thereafter. 24.20 527.880 Sqm 271.77 1,43,461.29

The scaffolding system shall be stiffened with bracings, runners, connecting with the

building etc, wherever required, if feasible, for inspection of work at required locations

with essential safety features for the workmen etc., complete as per directions and

approval of Engineer-in-charge.Note :- (1) The elevational area of the scaffolding shall

be measured for payment purpose.

(2) The payment will be made once only for execution of all items for such works.

Digitally signed by JAYA

NAME OF WORK :- Renovation of Training Centre Rooms, Dining Hall, Kitchen,

External Facade and Gate at L&D Centre NALCO, Bhubaneswar

ABSTRACT OF COST OF DINING HALL & RECREATION HALL

Sl. Description DSR Amount Non- DSR

No. (In Rs.) Amount

1 COST OF CIVIL WORK 5,06,252.46 17,75,239.85

2 COST OF PLUMBING WORK 1,62,449.04 45,571.00

3 COST OF ELECTRICAL WORK 2,28,892.61 44,756.00

Digitally signed by JAYA

NAME OF WORK :- Renovation of Training Centre Rooms, Dining Hall, Kitchen, External Facade and Gate at L&D Centre NALCO, Bhubaneswar

BILL OF QUANTITY FOR DINING HALL & RECREATION HALL

Sl. DSR-2019 Description Qty Unit DSR-Rate Non-DSR- Amount On Amount On

No. (In Rs.) Rate DSR-2019 Non- DSR

DEMOLISHING WORK

1 15.12 Dismantling doors, windows and clerestory windows (steel or wood) shutter including

chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

15.12.1 Of area 3 sq. metres and below 13.00 Each 289.21 3,759.67

2 15.23 Dismantling tile work in floors and roofs laid in cement mortar including stacking material

within 50 metres lead.

15.23.1 For thickness of tiles 10 mm to 25 mm 158.90 Sqm 57.79 9,182.58

3 15.56 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster

including disposal of rubbish to the dumping ground within 50 metres lead. 22.40 Sqm 920.40

4 15.60 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials

by mechanical means, including loading, ransporting, unloading to approved municipal

dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all

leads including all lifts involved. 4.31 Cum 630.50

5 13.91 Removing dry or oil bound distemper, water proofing cement paint and the like by

scrapping, sand papering and preparing the surface smooth including necessary repairs to 19.23

scratches etc. complete. 134.39 Sqm 2,584.01

6 6.13 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class

designation 75 in superstructure above plinth level up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand 4.50 Sqm 982.03 4,419.15

7 6.15 Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course

of half brick masonry. 4.50 Sqm 379.76

8 9.1.1 Providing wood work in frames of doors, windows, clerestory windows and other frames,

wrought framed and fixed in position with hold fast lugs or with dash fasteners of required

dia & length (hold fast lugs or dash fastener shall be paid for separately). 137157.14

Second class teak wood

9 9.21 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-

decorative type, core of block board construction with frame of 1st class hard wood and

well matched commercial 3 ply veneering with vertical grains or cross bands and face

veneers on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

10 9.23 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all

edges of flush door shutters (over all area of door shutter to be measured). 13.44 Sqm 5,683.82

11 9.40.1.2 Providing and fixing wooden moulded beading to door and window frames with iron

screws, plugs and priming coat on unexposed surface etc. complete :

2nd class teak wood

12 9.53 Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm

diameter bolts, nuts and wooden plugs and embedding in cement concrete block

300x100x150mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate

20mm nominal size). 36.00 Nos 6,796.80

13 9.84 Providing and fixing aluminium extruded section body tubular type universal hydraulic door

closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36

kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with

necessaryaccessories and screws etc. complete. 6.00 Each 5,383.33

14 9.101 Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic

coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour

or shade with necessary screws etc. complete.

9.101.2 Twin rubber stopper 12.00 Each 65.37 784.49

15 9.127 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss /

matt / suede finish with high density protective surface layer and reverse side of adhesive

bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved

16 9.165 Providing and fixing bright /matt finished Stainless Steel handles of approved quality &

make with necessary screws etc all complete. (a) 125 mm.

17 MR Providing & fixing Stainless steel sliding door bolts ISI marked anodised (anodic coating

not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade

with nuts and screws etc complete. (a) 250mm x 16mm . 12.00 Each 560.00 6,720.00

18 MR Providing and fixing stainless steel towerbolts (barrel type) with necessary screws etc.

Digitally signed by JAYA

19 MR System Aluminium Factory made Double Rebate Windows with Grill and Mesh

Providing and fixing of A2Z Series Double rebate windows & ventilators made of High-

performance factory-made system Aluminium windows with Akzonobel powder coating of

60-70 microns (Any RAL Colour). Section for Outer frame should be of 91mm x 35mm,

Glass shutter frame shall be of 54mm x 30mm, Mesh shutter frame shall be of 54mm x

30mm, 5mm thick Single Glazed beading shall be of 15mm x 18mm. 5mm thick Clear

Glass shall be used in all the windows & ventilators. Stainless Steel Wire Mesh shall be

used in Wire mesh Shutters. 10mm Sq bar M.S. Grill/Guard bar with 150mm c/c shall be

fixed in between glass & mesh shutter. All frame corners shall be joined/assembled using

self-locating corner cleats (No screwing at corners shall be allowed). All Hardware shall be

used from a reputed brand, weather silicon shall be used for filling the gap between

window opening & window Frame complete in all respect including all taxes.

20 9.134 Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with

wire of dia 0.5 mm and average width of aperture 1.4

mm in both directions for doors, windows and clerestory windows with necessary screws :

9.134.1.2.2 35 mm thick shutters.

With ISI marked stainless steel butt hinges of required size. 3410.41

Kiln seasoned and chemically treated hollock wood. 13.44 sqm 45,835.92

21 10.25 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in

position and applying a priming coat of approved steel primer using structural steel etc. as

10.25.2 In gratings, frames, guard bar, ladder, railings, brackets,gates and similar works 476.70 Kg 138.02 65,793.11

22 MR Providing and fixing machine cut, mirror/ eggshell polished , granite work for wall lining

(veneer work) including dado, skirting, risers of steps etc., in required design and pattern

wherever required, stones of different finished surface texture, on 12 mm (average) thick

cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @

3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching

shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings,

and as directed by the Engineer-in-Charge .

Granite of all colour except black, cherry/ruby red 18 mm thick (slab area above 0.50 sqm).

23 DSR 2023 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the

11.41A.1.3 manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of

(MR) approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement

mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm

including grouting the joints with white cement and matching pigments etc. The tiles must

be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the

notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet

for placing the tiles gently and easily.

Double charge vitrified tile polished finish of size

24 11.46.4 Providing and laying Vitrified tiles in different sizes (thickness to be specified by

manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of

approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of

cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ 2683.82

sqm including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 1000 x 1000 mm Or 600x1200 mm.

25 11.48.4 Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of

0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin

per kg), including filling / grouting and finishing complete as per direction of Engineer- 144.71

Size of Tile 1000 x 1000 mm Or 600x1200 mm. 158.90 sqm 22,994.11

26 12.45 Providing and fixing false ceiling at all height including providing and fixing of frame work

made of special sections, power pressed from M.S. sheets and galvanized with zinc

coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats

of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to

centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with

6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of

required length with nuts & bolts of required size and other end of angle hanger fixed with

intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to

centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered

flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in

a direction perpendicular to G.I. intermediate channel with connecting clips made out of

2.64 mm dia x 230 mm long G.I. wire at every junction, er ring shall confirm to

IS:5382.Knurling GI 50 mm (50X32X32X0.5X3660) floor and ceiling channel are to be

fixed with nylon plastic sleeves and wooden screws to from the proper framework .soft

coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved

make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection

internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and

U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be

decided by technical sanctioning authority as per the site

I. 12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011

(Board with BIS certification marks) 70.90 sqm 83,486.46

Digitally signed by JAYA

II. 12.45.3 12.5 mm thick tapered edge gypsum moisture resistant board. 28.00 sqm 1355.10 37,942.90

27 Providing and Fixing Knauf Channelled Woodworks perforated panels of width

192mm, thickness of 15mm and length 2400 mm, made of a Moisture resistant fibre board

substrate with a laminated facing as per the approved shade (Portland Maple, Sea Beech,

Siam Wood & Mystique Walnut, Interior White, Alumina Pearl) and a melamine balancing

layer on the reverse side. The boards shall have a special perforation pattern where the

reverse surface has a “Helmholtz” fluted perforation with consecutive 3mm wide groove

followed by 21mm of visible pane. The edges of the panel shall be “tongue-and-grooved” to

fix special clips for installation and seamless visual. The back of the perforated panel shall

have sound absorbing non-woven Soundtex acoustical fleece hot pressed to achieve NRC

of 0.5. (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000

Hz and 2000 Hz) as per ASTM C423 and Humidity Resistance (RH) of 70% with camber

limit less than 1mm/1000mm and bow less than 1mm/300mm.The panels shall be mounted

on special aluminium splines (keel) using inside clips provided by Knauf and approved by

the Architect/ Engineer-in-Charge.

28 Providing and fixing acoustic wooden (Knauf SoundScapes See Beech Lv1004 (G-21)

slotted panels of shade Sea Beech (Code: Lv1004 G-21), made of 12 mm thick HDF

substrate with decorative veneer finish on the front, balancing layer on the rear, and black

acoustic fleece backing, fixed on GI framework with 25 mm thick mineral wool (48–64

kg/m³ density) for acoustic performance, having NRC 0.90, complete as per manufacturer’s

specification,and direction of the Engineer in Charge.

WALL PANELLING/CLADDING

29 MR Supply and installation of high-quality decorative wallpaper for interior walls. The wallpaper

should be made from durable materials such as vinyl, non-woven, or paper, with a smooth,

consistent texture and design. The wallpaper should feature a design, pattern, or color

scheme as specified in the project requirements. It must be easy to maintain, resistant to

fading, and suitable for the intended room environment (e.g., living rooms, bedrooms,

offices). Installation includes preparation of the wall surface, cutting and fitting the

wallpaper to size, and ensuring proper alignment of patterns and seams. The wallpaper

should be securely adhered to the walls using appropriate adhesive, with any excess

trimmed neatly, all complete for all heights as per specifications, drawings and as directed

by Engineer-in-charge. 57.60 sqm 1,506.96 86,800.90

30 13.83 Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile

Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture,

including applying additional coats wherever required to achieve even shade and colour.

13.50 Applying priming coat :

31 13.50.2 With ready mixed aluminium primer of approved brand and manufacture on resinous wood

and plywood 22.92 Sqm 1,389.71

32 13.61 Painting with synthetic enamel paint of approved brand and manufacture of required colour

to give an even shade:

13.61.1 Two or more coats on new work 22.92 Sqm 128.06 2,935.17

33 13.99.1 Painting with synthetic enamel paint of approved brand and manufacture of required colour

to give an even shade: 84.23

One or more coats on old work 12.60 Sqm 1,061.34

34 13.68.1 French spirit polishing :

Two or more coats on new works including a coat of wood filler 16.13 Sqm 5,967.48

35 13.71 Lettering with black Japan paint of approved brand and manufacture per

36 2.34 Supplying chemical emulsion in sealed containers including delivery as specified.

Chlorpyriphos/ Lindane emulsifiable concentrate of 20%. 54.40 Ltr. 11,511.57

37 2.35 Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite

treatment (excluding the cost of chemical emulsion):

2.35.3.1 Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300

mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1

cement: 2 Coarse sand) to match the existing floor:

With Chlorpyriphos/Lindane E.C. 20% with 1% concentration 98.90 Sqm 23,658.20

GRAND TOTAL 22,81,492.31

GRAND TOTAL 22,81,492.31

Digitally signed by JAYA

DINING HALL & RECREATION HALL HVAC BOQ - NALCO BHUBANESHWAR (ODISHA)

S.No Description NDSR UNIT QTY.

1 VRV/VRF SYSTEMS

Supplying, Installation, Testing & Commissioning of Modular type Variable

Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for

cooling/heating having 100% hermetically sealed inverter type twin Rotary/Scroll

Compressor(s), minimum two compressors (with individual separate PCB) for

above 14HP modules, microprocessor based Controller, top discharge type

condensing unit(s), with R-410-A Refrigerant or equivalent, vibration Isolators with

suitable foundation etc. complete as required. To have better efficiency condenser

fan shall be capable to operate at different speed with respect to load. The unit shall

deliver the rated capacity and in confirmation as per IS 18728:2024 and CPWD

Specifications and work even at 50°C ambient temperature without tripping. The

system shall be able to deliver 100% of the rated capacity upto 39 0C. The unit

shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply and

BMS compatible. The unit shall be filled with first charge of the refrigerant and ready

for use as required. The condenser should be coated with a hydrophilic film to

prevent water accumulation on the surface of the heat exchanger, enhance water

dispersion, and reduce the risk of degradation, thereby improving overall

performance and durability. The Indian Seasonal Energy Efficiency Ratio (ISEER)

of the unit shall be as per Energy Conservation and Sustainable Building Code

(ECSBC) 2024 as below and complete as per CPWD specification, connections,

inter connections etc. as required. (For capacity <40 kWr ISEER 5.4, Capacity > 40

and <70 ISEER 5.5, Capacity > 70 ISEER 5.6 for ECSBC Building)

For Cooling or Heating or Both

Supplying, Installation, Testing and Commissioning of following minimum capacity

High wall type Indoor unit equipped with and comfort washable synthetic media

prefilter, fan section with low noise fan/dynamically balanced blower, multispeed

motor, coil section with DX copper coil, electronic expansion valve, outer cabinet,

cord less remote control, drain pan, necessary accessories etc., suitable for

2 operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required.

The Indoor units must shut down upon receiving a singal from the BMS System/Fire

Singnals. The system shall be capable to adjust air flow as per room requirement

automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27

0C DB and 19 0C WB temperature. (Make will be same as of Outdoor)

COPPER REFRIGERANT PIPING

Supplying, Installation, testing and commissioning including vaccumiazation and

Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant

piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type

hanger supports, jointing/brazing including accessories, insulated with XPLE Class-

O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular

sleeves sections of 19 mm thick insulation as given below for Suction and Liquid

lines, all accessories as per specifications etc. as required :

3.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Meter 139 256 35,530.00

3.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Meter 170 346 58,820.00

3.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Meter 80 487 38,960.00

3.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Meter 63 615 38,745.00

3.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Meter 60 739 44,340.00

3.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Meter 81 904 73,224.00

3.7 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Meter 45 1068 48,060.00

3.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Meter 55 1157 63,635.00

Say in Lacs 6,30,000.00

Digitally signed by JAYA

NAME OF WORK :- Renovation of Training Centre Rooms, Dining Hall, Kitchen, External Facade and Gate at L&D Centre NALCO, Bhubaneswar

PLUMBING WORK OF DINING HALL & RECREATION HALL

Non-DSR- Amount On Amount On

Sl. DSR- DSR-Rate

Description Qty Unit Rate DSR-2019 Non- DSR

1 15.42 Dismantling C.I. or asbestos rain water pipe with fittings

and clamps including stacking the material within 50 metres

2 15.44 Dismantling G.I. pipes (external work) including excavation

and refilling trenches after taking out the pipes, manually/

by mechanical means including stacking of pipes within 50

metres lead as per direction of Engineer-in-charge :

15.44.1 15 mm to 40 mm nominal bore 15.00 Mtr 113.94 1,709.16

3 15.45 Dismantling C.I. pipes including excavation and refilling

trenches after taking out the pipes, manually/ by

mechanical means breaking lead caulked joints, melting of

lead and making into blocks including stacking of pipes &

lead at site within 50 metre lead as per direction of

Engineer-in-charge:

4 15.53 Dismantling of C.I. sluice valve including stacking of useful

materials within a lead of 50 metres

15.53.1 Up to 150 mm diameter 4.00 Each 251.86 1,007.43

5 12.41 Providing and fixing on wall face unplasticised Rigid PVC

rain water pipes conforming to IS : 13592 Type A, including

jointing with seal ring conforming to IS : 5382, leaving 10

mm gap for thermal expansion, (i) Single socketed pipes.

6 12.42 Providing and fixing on wall face unplasticised - PVC

moulded fittings/ accessories for unplasticised Rigid PVC

rain water pipes conforming to IS : 13592 Type A, including

jointing with seal ring conforming to IS : 5382, leaving 10

mm gap for thermal expansion.

12.42.1.2 a) Coupler

7 13.96 Painting (one or more coats) on rain water, soil, waste and

vent pipes and fittings with synthetic enamel paint of

approved brand and manufacture and required colour on

13.96.1 75 mm diameter pipes 0.00 Mtr 22.92 -

13.96.2 100 mm diameter pipes 10.00 Mtr 29.45 294.47

8 17.7 Providing and fixing wash basin with C.I. brackets, 15 mm

C.P. brass pillar taps, 32 mm C.P. brass waste of standard

pattern, including painting of fittings and brackets, cutting

and making good the walls wherever require:

17.7.4 White Vitreous China Flat back wash basin size 550x 400

mm with single 15 mm C.P. brass pillar tap. 3.00 Each 7,934.82

9 MR Providing and fixing of C. P. brass towel rail 600 x 20 mm

size complete with C.P. brass brackets 2.00 Each 2869.00 5,738.00

10 MR Providing and fixing CP Brass soap dish 109 mm wide,

125 mm high and 112 mm distance from wall of standard

shape with bracket and all fittings of the same material of

approved quality and colour.

Digitally signed by JAYA

11 Providing, fixing, jointing and testing in position of ISI

marked UV stabilized UPVC pipes for soil, waste, and

vent, Type-B as per IS : 13592 suitable for rubber ring

joints, including all neccessary specials and fittings

(confirming to IS:14735) i.e. bends, tees, junctions (with or

without doors), reducers, WC connectors, couplers,

expansion joints / bellows, cowels, clamps, rubber rings,

clean outs etc. fixing at wall/ ceiling/ floor level supported by

clamp & hangers etc. in concealed / inside duct / under

floor & basement ceiling / external work etc. including

chase cutting as required, excavation and back filling in all

kind of soils, suspended from floor under false ceiling or

embedding the pipes laid under floors / building in 75 mm.

alround 1:2:4 cement concrete (1 cement : 2 coarse sand :

4 graded stone aggregate 20 mm nominal size) including

cost of shuttering for proper completion of the work,

breaking and making good the walls and floors etc. after

pipes have been duly laid and tested. The rubber ring shall

confirm to IS:5382.

The Pipes will be supported with threaded G I rods & U

clamps with nuts, washers etc on 50x50x5 mm slotted

angle. The cost will include all support arrangements. The

work includes commissioning of all pipes lines as per

drawings and specifications and as directed by engg-in-

charge at site.

MR 110 mm dia (Wall Thickness - 3.2 to 3.8 mm) 15.00 Mtr 790.18 11,852.68

MR 75 mm dia (Wall Thickness - 3.2 to 3.8 mm) 10.00 Mtr 579.46 5,794.64

12 Providing & fixing UPVC Floor trap of self cleansing design

with stainless steel grating complete in all respects.

MR Multi Floor Trap (5" Ht) with height raiser and branch saddle

strip of 50/75 mm outlet 2.00 Each 673.00 1,346.00

MR Plain Floor Trap (4" Ht) with 50 / 75 outlet and with height

MR P-Trap type Floor Trap 110 x 75 mm 3.00 Each 565.00 1,695.00

13 MR Extra for providing & fixing 125 mm dia C.P. grating in

place of C.I. grating over floor traps. 21.00 Each 597.00 12,537.00

14 MR Providing & fixing of SS Floor Cleanout, round or square

with rubber seal and flat round cover with screws and other

required fitting complete as required. 25.00 Each 389.00 9,725.00

15 17.29 Providing and fixing 100 mm sand cast Iron grating for gully

trap. 2.00 Each 93.98

16 17.31 Providing & fixing 600x450mm bevelled edge mirror of

superior glass (of approved quality) complete with 6mm

thick asbestos cement sheet ground fixed to wooden cleats

with C.P. brass screws and washers. 3.00 Each 4,055.35

17 17.35 Providing & fixing soil, waste and vent pipes.

17.35.1.2 a) 100mm dia centrifugally cast iron S & S pipe. 10.00 Mtr 1150.71 11,507.11

17.35.2.2 b) 75mm dia centrifugally cast iron S & S pipe. 5.00 Mtr 1045.20 5,225.98

18 17.37 Providing & fixing M.S. holder bat clamps of approved

design to sand cast iron/centrifugally cast (Spun) iron S & S

pipe embeded in & including cement concrete blocks

10x10x10cm. of 1:2:4 mix (1 cement : 2 coarse : 4 graded

stone aggregate 20mm nominal size). Including cost of

cutting holes & making good the walls etc.

19 17.38 Providing and fixing bend of required degree with access

door, insertion rubber washer 3mm thick, bolts and nuts

17.38.1.2 Sand cast iron S&S as per IS - 3989 4.00 Each 486.38 1,945.53

17.38.2.2 Sand cast iron S&S as per IS- 3989 4.00 Each 405.36 1,621.45

20 17.39 Providing and fixing plain cast iron S & S sanitary bend.

17.39.1.1 Sand cast iron S&S as per IS - 1729 4.00 Each 401.78 1,607.12

17.39.2.2 Sand cast iron S&S as per IS - 3989 4.00 Each 305.27 1,221.09

Digitally signed by JAYA

21 17.43 Providing and fixing single equal plain junction of required

degree with access door, insertion rubber washer 3 mm

thick, bolts and nuts complete.

22 17.56 Providing and fixing cast iron terminal guard.

23 17.57 Providing & fixing cast iron coller.

17.57.1.2 Sand cast iron S&S as per IS - 3989 4.00 Each 431.38 1,725.54

17.57.2 b) 75mm dia.

17.57.2.2 Sand cast iron S&S as per IS - 3989 4.00 Each 270.03 1,080.12

24 17.58 Providing lead caulked joints to sand cast iron/centrifugally

cast (spun) iron pipes & fitting of diameters.

25 17.60 Providing & fixing cast iron trap of self cleansing design with

or without ventarm complete, including cost of cutting &

making good the walls & floors.

26 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, having thermal stability for hot & cold water supply,

including all CPVC plain & brass threaded fittings, i/c fixing

the pipe with clamps at 1.00 m spacing. This includes

jointing of pipes & fittings with one step CPVC solvent

cement and the cost of cutting chases and making good

the same including testing of joints complete as per

direction of Engineer in Charge.

18.8.1 15 mm nominal outer dia Pipes 35.00 Mtr 431.60 15,105.84

18.8.2 20 mm nominal outer dia Pipes 30.00 Mtr 503.77 15,112.96

18.8.3 25 mm nominal outer dia Pipes 20.00 Mtr 592.05 11,841.09

18.8.4 32 mm nominal outer dia Pipes 10.00 Mtr 715.53 7,155.33

27 18.16 Providing and fixing brass stop cock of approved quality.

18.16.1 15 mm nominal bore 4.00 Each 343.94 1,375.75

28 18.17 Providing and fixing gun metal gate valve with wheel of

approved quality.

18.17.1 a) 25mm dia nominal bore 4.00 Each 523.78 2,095.13

18.17.2 b) 32mm dia nominal bore 4.00 Each 612.39 2,449.55

29 18.18 Providing and fixing ball valve (brass) of approved quality

complete. (High or low pressure with plastic floats).

18.18.3 a) 25mm. Nominal bore 4.00 Each 415.11 1,660.43

30 18.21 Providing and fixing 30 cm long unplasticised PVC

connection pipe with brass unions.

18.21.1.1 a) 15mm nominal bore 4.00 Each 76.75 307.01

31 18.21 Providing and fixing 45 cm long unplasticised PVC

connection pipe with brass unions.

18.21.2.1 a) 15mm nominal bore 4.00 Each 87.45 349.79

32 18.51 Providing & fixing C.P. brass long body bib cock of

approved quality conforming to IS standards and weighing

not less than 690 gms.

18.51.1 a) 15mm nominal bore 4.00 Each 581.94 2,327.76

33 18.53 Providing & fixing C.P. brass angle valve for basin mixer

and gyser points of approved quality conforming to IS 8931

18.53.1 a) 15mm nominal bore 8.00 Each 560.50 4,484.00

34 18.53A Providing and fixing C.P. Brass extension nipple (size

15mmx50mm) of approved make and quality as per 64.53

direction of Engineer-in-charge. 4.00 Each 258.13

35 18.76 Cutting holes up to 30x30 cm in walls including making

18.76.1 With common burnt clay F.P.S. (non modular) bricks 4.00 Each 344.78 1,379.13

Digitally signed by JAYA

36 18.77 Cutting holes up to 15x15 cm in R.C.C. floors and roofs for

passing drain pipe etc. and repairing the hole after insertion

of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2

coarse sand : 4 graded stone aggregate 20 mm nominal

size), including finishing complete so as to make it leak

proof. 4.00 Each 1,452.24

37 18.78 Making chases up to 7.5x7.5 cm in walls including making

good and finishing with matching surface after housing G.I. 162.41

pipe etc. 25.00 Mtr 4,060.20

38 19.26 Raising manhole cover and frame slab to required level

including dismantling existing slab and making good the

damage as required (Raising depth of manhole to be paid

19.26.1 Rectangular manhole 90x80 cm with rectangular cover

600 x 450 mm of grade LD - 2.5 2.00 Each 5,179.25

39 14.75A Cleaning of terrace/loft water storage tank (inside surface

area) upto 2000 litre capacity at all heights with coconut

brushes, duster etc., removal of silt, rubbish from the tank

and cleaning the tank with fresh water disinfecting with

bleaching powder @ 0.5gm per litre capacity of tank

including marking the date of cleaning on the side of tank

body with the help of stencil and paint and disposing of

malba all complete as per direction of Engineer-in-Charge.

(The old date already written on tank should be removed

with paint remover or black paint and if date is not written

with the stencil or old date is not removed deduction will be

made @ Rs. 0.10 per litre) (if during cleaning any GI fittings

or ball cock is damaged that is to be repaired by contractor

at his own cost and nothing extra will be paid on this

Digitally signed by JAYA

NAME OF WORK :- Renovation of Training Centre Rooms, Dining Hall, Kitchen, External Facade and Gate at L&D Centre NALCO, Bhubaneswar

ELECTRICAL WORK OF DINING HALL & RECREATION HALL

Non-DSR- Amount On Amount On

Sl. DSR- DSR-Rate

Description Qty Unit Rate DSR-2022 Non- DSR

1 1.8 Wiring for light point/ fan point/ exhaust fan point/ call bell point

with 1.5 sq.mm FR PVC insulated copper conductor single

core cable in surface / recessed medium class PVC conduit,

with piano type switch, phenolic laminated sheet, suitable size

M.S. box and earthing the point with 1.5 sq.mm. FR PVC

insulated copper conductor single core cable etc as required.

2 1.9 Wiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, 2 way piano type switch,

phenolic laminated sheet, suitable size MS box and earthing 1535.05

the point with 1.5 sq.mm. FRLS PVC insulated copper

conductor single core cable etc. as required.

3 1.12 Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated

copper conductor single core cable in surface/ recessed

medium class PVC conduit alongwith 1 No 4 sq. mm FR PVC 351.89

insulated copper conductor single core cable for loop earthing

as required. 20.00 Mtr 7,037.86

4 1.14 Wiring for circuit/ submain wiring alongwith earth wire with the

following sizes of FR PVC insulated copper conductor, single

core cable in surface/ recessed medium class PVC conduit as

5 1.15 Rewiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FR PVC insulated copper conductor

single core cable and 1.5 sq.mm. FR PVC insulated copper

conductor single core cable as earth wire in existing surface/

recessed steel conduit including dismantling as required.

6 1.16 Rewiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable and 1.5 sq.mm

FRLS PVC insulated copper conductor single core cable as 941.89

earth wire in existing surface/ recessed steel/PVC conduit

including dismantling as required. 8.00 Point 7,535.14

7 1.17 Supplying and drawing following sizes of FR PVC insulated

copper conductor, single core cable in the existing surface/

recessed steel/ PVC conduit as required.

8 1.21 Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of recessed

conduit as required.

9 1.22 Supplying and fixing metal box of following sizes (nominal size)

on surface or in recess with suitable size of phenolic laminated

sheet cover in front including painting etc. as required.

10 1.29 Supplying and fixing metal box of 150mm X 75mm X 60mm

deep (nominal size) on surface or in recess with suitable size

of phenolic laminated sheet cover in front including providing

and fixing 3 pin 5/6 amps socket outlet and 5/6 amps piano 377.18

type switch, connection, painting etc. as required. (For light

plugs to be used in non residential buildings).

11 1.30 Supplying and fixing metal box of 180mm X 100mm X 60mm

deep (nominal size) on surface or in recess with suitable size

of phenolic laminated sheet cover in front including providing

and fixing 6 pin 5/6 & 15/16 amps socket outlet and 15/16

amps piano type switch, connection, painting etc. as required. Digitally signed by JAYA

8.00 Each 4,113.14 GURU

12 S/F light plug point Modular type accessories :-

1.31 Supply and fixing of suitable size GI box with modular plate

and cover in front on surface or in recess including providing

and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps. 502.55

modular switch, connection etc. as required.

13 S/F power plug point modular type accessories :-

1.32 Supply and fixing of suitable size GI box with modular plate

and cover in FRLSont on surface or in recess, including

providing and fixing 6 pin 5/6 & 15/16 amps modular socket 617.39

outlet and 15/16 amps. modular switch, connection etc. as

required. 16 Each 9,878.29

14 1.33 Supplying and fixing 3 pin, 5 amp ceiling rose on the existing

junction box/ wooden block including connection etc as 91.66

required. 8.00 Each 733.29

15 1.34 Supplying and fixing brass batten/ angle holder including

connection etc. as required. 8.00 Each 1,104.14

16 2.3 Supplying and fixing following way, single pole and neutral,

sheet steel, MCB distribution board, 240 volts, on surface/

recess, complete with tinned copper bus bar, neutral bus bar,

earth bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

2.3.1 6 way, Double door 2.00 Each 2324.18 4,648.36

17 2.4 Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 volts, on

surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without

MCB/RCCB/Isolator)

18 2.10 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts,

"C" curve, miniature circuit breaker suitable for inductive load

of following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

2.10.2 Single pole and neutral 6.00 Each 631.09 3,786.54

2.10.5 Triple pole and neutral 2.00 Each 1293.79 2,587.57

19 2.11 Supplying and fixing single pole blanking plate in the existing

MCB DB complete etc. as required. 2.00 Each 27.39

20 2.21 Providing and fixing M.V. danger notice plate of 200 mm X 150

mm, made of mild steel, at least 2 mm thick, and vitreous

enameled white on both sides, and with inscription in single red

colour on front side as required. 1.00 Each 283.41

21 5.2 Earthing with G.I. earth pipe 4.5 Mtr long, 40 mm dia including

accessories, and providing masonry enclosure with cover plate

having locking arrangement and watering pipe etc. with

charcoal/ coke and salt as required. 2.00 Each 14,444.46

22 5.12 Providing and laying earth connection from earth electrode with

6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth

electrode including connection with G.I. thimble excavation and

re-filling as required. 10.00 Mtr 3,023.75

23 5.15 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in

recess for connections etc. as required. 10.00 Mtr 2,570.71

24 5.16 Providing and fixing 6 SWG dia G.I. wire on surface or in

recess for loop earthing as required. 10.00 Mtr 737.50

25 1.41 Installation, Testing and Commissioning of pre-wired,

fluorescent fitting / compact fluorescent/ LED fitting of all types,

complete with all accessories and tube/lamp etc. directly on

ceiling/ wall, including connections with 1.5 sq. mm

FRLS/HFFR PVC insulated, copper conductor, single core

cable and earthing etc. as required. 24.00 Each 5,208.86

26 1.50 Installation of exhaust fan in the existing opening, including

making good the damage, connection, testing, commissioning

etc. as required.

27 NSDR Supply of 15W SURFACE MOUNTED ROUND LED with all

accessories as per standard item.. 10.00 Each 1,345.00 13,450.00

Digitally signed by JAYA

28 NSDR Supply of 20W SURFACE MOUNTED ROUND LED with all

accessories as per standard item.. 4.00 Each 953.00 3,812.00

29 NSDR Supply of 15W WALL BRACKET LED BULB with all

accessories as per standard item.. 4.00 Each 378.00 1,512.00

30 NSDR Supply of 20W SURFACE MOUNTED LED TUBE with all

accessories as per standard item. 6.00 Each 897.00 5,382.00

31 NSDR Providing and fixing concealed LED strip lighting in cove/false

ceiling, comprising of high quality flexible LED strip (minimum

9W per meter, warm white/cool white as approved), including

extruded aluminium profile with opal diffuser, complete with

driver (SMPS), connectors, wiring, soldering, fixing inside

ceiling groove, testing and commissioning, complete in all

respects as per direction of Engineer-in-charge.

32 NSDR Supply of AC 230/250 volts, 50 HZ exhaust fans including

providing nuts, bolts, mounting FRLSame and other

accessories etc. complete

Digitally signed by JAYA

NAME OF WORK :- Renovation of Training Centre Rooms, Dining Hall, Kitchen,

ABSTRACT OF COST GUARD ROOM.

Sl. No. Description Amount

1 COST OF CIVIL WORK 36,51,233.47 3,28,310.12

2 COST OF PLUMBING WORK 71,013.19 27,207.00

3 COST OF ELECTRICAL WORK. 52,039.32 77,400.00

S.N. DESCRIPTION OF ITEM Non-DSR-

SCH. NO. QTY. UNIT DSR-RATES RATES AMOUNT AMOUNT

DSR 2019 MR ITEMS

1 Excavation work by mechanical means (Hydraulic excavator)/

manual means in foundation trenches or drains (not exceeding

1.5m in width or 10 sqm on plan), including dressing of sides

and ramming of bottoms, lift upto 1.5 m, including getting out

2.8.1 the excavated soil and disposal of surplus excavated soils as 54.46 CUM 265.82 14,476.34

Filling within aexcavated

available lead of 50earth

m. (excluding rock) in trenches,

plinth, sides of foundations etc. in layers not exceeding 20cm in

depth,consolidating each deposited layer by ramming and

watering, lead upto 50 m and lift upto 1.5 m.

3 Supplying and filling in plinth with sand under floors, including

watering, ramming, consolidating and dressing complete.

Diluting and injecting chemical emulsion for POST-

CONSTRUCTIONAL anti-termite treatment (excluding the cost

4 2.35 of chemical emulsion) :

Treatment of soil under existing floors using chemical

emul sion @ one litre per hole, 300 mm apart including drilling

12 mm diameter holes and plugging with cement mortar 1 :2 (1

2.35.3 cement : 2 Coarse sand) to match the existing floor:

2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration 12.11 Sqm 239.21 2,896.87

Supplying chemical emulsion in sealed containers including

delivery as specified.

2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% 7.00 Ltr. 211.61 1,481.27

B CONCRETE WORK

6 Providing and laying in position cement concrete of specified

grade excluding the cost of centering and shuttering - All work

up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III)

natural sources : 8 graded stone aggregate 40 mm nominal

4.1.8 size derived from natural sources) 6.170 CUM 6099.76 37,635.50

7 Providing and laying damp-proof course 40mm thick with

cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-iii)

derived from natural sources : 4 graded stone aggregate

12.5mm nominal size derived from natural sources)

8 Extra for providing and mixing water proofing material in cement per

concrete work in doses by weight of cement as per 50kg

4.12 manufacturer's specification. 1.000 ceme 59.58 59.58

9 Providing & applying a coat of residual petroleum bitumen of

of VG-10 of approved quality using 1.7 kg per square metre on

damp proof course after cleaning the surface with brushes and

finally with a piece of cloth lightly soaked in kerosene oil.

10 Making plinth protection 50mm thick of cement concrete 1:3:6 (1

cement : 3 coarse sand (zone - III) : 6 graded stone aggregate

20 mm nominal size) over 75mm thick bed of dry brick ballast

40 mm nominal size, well rammed and consolidated and

grouted with fine sand, including necessary excavation, levelling

& dressing & finishing the top smooth.

Brick edging in full brick width and half brick depth including

excavation, refilling and disposal of surplus earth lead upto 50

metres.With common burnt clay F.P.S. (non modular) bricks of

12 Analysis Brick Drain along Plinth Protection (Size 250X300 MM ) 20.37 Rm 2570.26 52,356.22

Digitally signed by JAYA

13 5.9 Centering and shuttering including strutting, propping etc. and

removal of form for all heights :

(a) Foundations, footings, bases of columns, etc. for mass

(b) 5.9.6 Columns,Pillars, Piers, Abutments, Posts and Struts. 94.860 SQM 773.01 73,327.29

(c) Edges of slabs and breaks in floors and walls

(d) Suspended floors, roofs, landings, balconies and access

5.9.20 platform. with water proof ply 12 mm thick 19.120 SQM 821.05 15,698.44

(e) Lintels, beams, plinth beams, girders, bressumers and

5.9.21 cantilevers. with water proof ply 12 mm thick 60.920 SQM 675.97 41,180.18

14 Providing and laying in position ready mixed or site batched

design mix cement concrete for reinforced cement concrete

work; using coarse aggregate and fine aggregate derived from

natural sources, Portland Pozzolana / Ordinary Portland

cement, admixtures in recommended proportions as per IS:

9103 to accelerate / retard setting of concrete, to improve

durability and workability without impairing strength; including

pumping of concrete to site of laying, curing, carriage for all

leads; but excluding the cost of centering, shuttering, finishing

and reinforcement as per direction of the engineer-in-charge; for

the following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement

content in design mix shall be payable separately. In case the

cement content in design mix is more than 1.10 times of the

specified minimum cement content, the contractor shall have

discretion to either re-design the mix or bear the cost of extra

(a) 5.33.1 All works upto plinth level

Concrete of M25 grade with minimum cement content of

(iii) 5.33.1.1 R.C.C. work in Columns 1.290 CUM 8425.73 10,869.19

(b) 5.33.2 All works above plinth level upto floor V level

(ii) 5.33.2.1 R.C.C. work in Columns 6.93 CUM 9904.47 68,637.96

15 Steel reinforcement for R.C.C. work including straightening,

cutting, bending, placing in position and binding all complete

Thermo-Mechanically Treated bars of grade Fe-500D or more.

upto plinth level.

16 Steel reinforcement for R.C.C. work including straightening,

cutting, bending, placing in position and binding all complete

Thermo-Mechanically Treated bars of grade Fe-500D or more.

above plinth level.

17 Add for plaster drip course/ groove in plastered surface or

5.30 moulding to .R.C.C. projections. 36.000 RM 62.06 2,233.99

18 Brick work with common burnt clay F.P.S. (non modular) bricks

of class designation 7.5 in foundation and plinth in: Cement

6.1.2 mortar 1:6 (1 cement : 6 coarse sand). 4.90 CUM 6487.31 31,787.84

19 Brick work with common burnt clay F.P.S. (non modular) bricks

of class designation 7.5 in superstructure above plinth level up

6.4.2 to floor V level in all shapes and sizes in :

Cement mortar 1:6 (1 cement : 6 coarse sand)

20 Half brick masonry with common burnt clay F.P.S. (non

modular) bricks of class designation 7.5 in superstructure above

plinth level up to floor V level.Cement mortar 1:4 (1 cement :4

21 Extra for providing and placing in position 2 Nos 6mm dia. M.S.

6.15 bars at every third course of half brick masonry. 6.12 SQM 84.39 516.47

Digitally signed by JAYA

22 Providing and fixing ISI marked flush door shutters conforming

to IS : 2202 (Part I) non-decorative type, core of block board

construction with frame of 1st class hard wood and well

matched commercial 3 ply veneering with vertical grains or

9.21.1 cross bands and face veneers on both faces of shutters:35 mm 2.10 SQM 1987.77 4,174.32

thick including ISI marked Stainless Steel butt hinges with

23 Extra for providing lipping with 2nd class teak wood battens 25

mm minimum depth on all edges of flush door shutters (over all

9.23 area of door shutter to be measured). 2.10 SQM 422.90 888.10

24 Providing and fixing bright /matt finished Stainless Steel handles

of approved quality & make with necessary screws etc all

complete(a) 125 mm.

25 Providing and fixing M.S. grills of required pattern in frames of

windows etc. with M.S. flats, square or round bars etc. including

priming coat with approved steel primer all complete. Fixed to

9.48.1 steel windows by welding. 19.44 KG 174.16 3,385.58

26 Providing and fixing oxidised M.S. casement stays (straight peg

9.68 type) with necessary screws etc. complete.

(ii) 9.68.2 250 mm weighing not less than 150 gms 1.00 NOS 54.15 54.15

27 Providing and fixing aluminium casement stays, ISI marked,

anodised (anodic coating not less than grade AC 10 as per IS :

DSR 1868) transparent or dyed to required colour and shade, with

9.102 necessary screws etc. complete. 1.00 NOS 65.90 65.90

28 Providing & fixing Stainless steel sliding door bolts ISI marked

anodised (anodic coating not less than grade AC 10 as per IS :

1868) transparent or dyed to required colour or shade with nuts

and screws etc complete. (a) 250mm x 16mm .

29 Providing and fixing aluminium casement stays, ISI marked,

anodised (anodic coating not less than grade AC 10 as per IS :

1868) transparent or dyed to required colour and shade, with

necessary screws etc. complete.

WPC DOOR FRAME & SHUTTERS FOR TOILETS

30 DSR 2023 Providing and fixing factory made single extruded WPC (Wood

26.86.5 Polymer Composite) solid door/window/Clerestory windows &

(MR) other Frames/Chowkhat comprising of virgin PVC polymer of K

value 58-60 (Suspension Grade), calcium carbonate and natural

powder/ rice husk/wheat husk) and non toxic additives

(maximum toxicity index of 12 for 100 gms) fabricated with miter

joints after applying PVC solvent cement and screwed with full

body threaded star headed SS screws having minimum frame

density of 750 kg/cum, screw

withdrawal strength of 2200 N (Face) & 1100 N (Edge),

minimum compressive strength of 58 N/mm2, modulus of

elasticity 900 N/mm2 and resistance to spread of flame of Class

A category with property of being termite/borer proof,

water/moisture proof and fire retardant

and fixed in position with M.S hold fast/lugs/SS dash fasteners

of required dia and length complete as per direction of Engineer-

In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be

paid for separately).

Note: For WPC solid door/window frames, minus 5mm

tolerance in dimensions i.e depth and width of profile shall be

acceptable. Variation in profile dimensions on plus side shall be

acceptable but no extra payment on this account shall be made.

Frame size 65 x 100 mm

Digitally signed by JAYA

31 DSR 2023 Providing and fixing factory made single extruded WPC (Wood

26.87.2 Polymer Composite) solid plain flush door shutter of required

(MR.) size comprising of virgin polymer of K value 58-60 (Suspension

Grade), calcium carbonate and natural fibers (wood powder/

rice husk/wheat husk) and non toxic additives (maximum toxicity

index of 12 for 100 gms) having minimum

density of 650 kg/cum and screw withdrawal strength of 1800 N

(Face) & 900 N (Edge), minimum compressive strength 50

N/mm2, modulus of elasticity 850 N/mm2 and resistance to

spread of flame of Class A category with property of being

termite/borer proof, water/ moisture proof and fire retardant and

fixing with stainless steel butt hinges of required size with

necessary full body threaded star headed counter sunk S.S

screws, all as per direction of Engineer-In- Charge. (Note:

stainless steel butt hinges and necessary S.S screws shall be

paid separately) 35 mm thick

32 Providing 40x5 mm flat iron hold fast 400 mm long including

fixing to frame with 10 mm diameter bolts, nuts and wooden

plugs and embedding in cement concrete block

300x100x150mm 1:3:6 mix (1 cement : 3 coarse sand : 6

graded stone aggregate 20mm nominal size).

33 Providing and fixing IS : 12817 marked stainless steel butt

hinges (heavy weight) with stainless steel screws etc. complete

34 Providing and fixing factory made ISI marked steel glazed

doors, windows and ventilators, side /top /centre hung, with

beading and all members such as F7D, F4B, K11 B and K12 B

etc. complete of standard rolled steel sections, joints mitred and

flash butt welded and sash bars tenoned and riveted, including

providing and fixing of hinges, pivots, including priming coat of

approved steel primer, but excluding the cost of other fittings,

complete all as per approved design, (sectional weight of only

steel members shall be measured for payment). Fixing with

15x3 mm lugs 10 cm long embedded in cement concrete block

15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6

graded stone aggregate 20 mm nominal size).

35 Providing and fixing T-iron frames for doors, windows and

ventilators of mild steel Tee-sections, joints mitred and welded,

including fixing of necessary butt hinges and screws and

applying a priming coat of approved steel primer

Fixing with 15x3 mm lugs 10 cm long embedded in cement

concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse

sand : 6 graded stone aggregate 20 mm nominal size

36 Providing and fixing M.S. Tubular frames for doors, windows,

ventilators and cupboard with rectangular/ L-Type sections,

made of 1.60 mm thick M.S. Sheet, joints mitred, welded and

grinded finish, with profiles of required size, including fixing of

Fixing withbutt hinges

10 cmand applying

long a priming

concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse

sand : 6 graded stone aggregate 20 mm nominal size)

37 Providing & fixing glass panes with putty and glazing clips in

steel doors, windows, clerestory windows, all complete with

10.30.1 4 mm thick glass panes 0.360 SQM 948.79 341.57

38 Extra for providing frosted glass panes 4 mm thick (weight not

less than 10 kg per sqm) instead of ordinary float glass panes 4

mm thick (weight not less than 10 kg per sqm) in doors,

windows and clerestory window shutters. (Area of opening for

glass panes excluding portion inside rebate shall be measured).

Digitally signed by JAYA

38 Providing and laying flamed finish Granite stone flooring in

required design and patterns, in linear as well as curvilinear

portions of the building all complete as per the architectural

drawings with 18 mm thick stone slab over 20 mm (average)

thick base of cement mortar

1:4 (1 cement : 4 coarse sand) laid and jointed with cement

slurry and pointing with white cement slurry admixed with

pigment of matching shade including rubbing, curing and

polishing etc. all complete as specified and as directed by the

Engineer-in-Charge :Flamed finish granite stone slab Jet Black,

Cherry Red, Elite Brown, Cat Eye or equivalent

39 DSR 2023 Providing and laying Vitrified tiles in floor in different sizes

11.41A.3.1 (thickness to be specified by the manufacturer) with water

(MR) absorption less than 0.08% and conforming to IS:15622, of

approved brand & manufacturer, in all colours and shade, laid

on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand)

jointing with grey cement slurry @3.3 kg/sqm including grouting

the joints with white cement and matching pigments etc. The

tiles must be cut with the zero chipping diamond cutter only .

Laying of tiles will be done with the notch trowel, plier, wedge,

clips of required thickness, leveling system and rubber mallet for

placing the tiles gently and easily.Glazed Vitrified tiles

Matt/Antiskid finish of size

Size of Tile 600 x 600 mm

40 Providing and fixing Ist quality Double charged vitrified tiles

polished finish of size 60 x 120 cm tiles conforming to IS:

15622 (thickness to be specified by the manufacturer), of

approved make, in all colours, shades except burgundy, bottle

green, black of any size as approved by Engineer-in-Charge, in

skirting, risers of steps and dados, over 12 mm thick bed of

cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with

grey cement slurry @ 3.3kg per sqm, including pointing in white

cement mixed with pigment of matching shade complete.

H PLASTERING AND POINTING

41 15 mm cement plaster on the rough side of single or half brick

13.5.2 wall of mix : 1:6 (1 cement: 6 coarse sand) 99.16 SQM 320.18 31,749.08

INNERSIDE PLASTER

42 12mm cement plaster in single coat on fair side of single or half

brick wall for exterior plastering up to floor two level including

internal rounded angles chamfers, and/or rounded angles not

exceeding 80mm in girth and finished even and smooth no extra

for mixing any additive. 1:6 (1 cement: 6 coarse sand)

CEILING PLASTER 6MM THICK

43 6 mm cement plaster on celling (a) 1:3(1 cement:3 fine sand)

44 Wall painting with premium acrylic emulsion paint of interior

grade, having VOC (Volatile Organic Compound ) content less

than 50 grams/ litre of approved brand and manufacture,

13.83.2 including applying additional coats wherever required to achieve 61.260 SQM 120.00 7,351.31

Finishing andwith

textured exterior paint of required shade :

45 New work (Two or more coats applied @ 3.28 ltr/10 sqm) over

and including priming coat of exterior primer applied @

46 Providing and applying white cement based putty of average

thickness 1 mm, of approved brand and manufacturer, over the

plastered wall surface to prepare the surface even and smooth

47 Providing and applying plaster of paris putty of 2 mm thickness

13.26 over plastered surface to prepare the surface even and smooth 19.120 SQM 207.24 3,962.38

Digitally signed by JAYA

48 Painting with synthetic enamel paint of approved brand and

manufacture of required colour to give an even shade :

13.62.1 Two or more coats on new work over an under coat of

suitable shade with ordinary paint of approved brand and

J WATER PROOFING

49 Providing and laying integral cement based water proofing

treatment including preparation of surface as required for

treatment of roofs, balconies, terraces etc consisting of following

operations: (a) Applying a slurry coat of neat cement using 2.75

kg/sqm of cement admixed with water proofing compound

conforming to IS. 2645 and approved by Engineer-in-charge

over the RCC slab including adjoining walls upto 300 mm height

including cleaning the surface before treatment. (b) Laying brick

bats with mortar using broken bricks/brick bats 25 mm to 115

mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse

sand) admixed with water proofing compound conforming to IS :

2645 and approved by Engineer-in-charge over 20 mm thick

layer of cement mortar of mix 1:5 (1 cement :5 coarse sand)

admixed with water proofing compound conforming to IS : 2645

and approved by Engineer-in-charge to required slope and

treating similarly the adjoining walls upto 300 mm height

including rounding of junctions of walls and slabs. (c) After two

days of proper curing applying a second coat of cement slurry

using 2.75 kg/ sqm of cement admixed with water proofing

compound conforming to IS : 2645 and approved by Engineer-in-

charge. (d) Finishing the surface with 20 mm thick jointless

cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed

with water proofing compound conforming to IS : 2645 and

approved by Engineer-in-charge including laying glass fibre

cloth of approved quality in top layer of plaster and f inally

22.7.1 finishing the surface with trowel with neat cement slurry and 19.12 SQM 1473.42 28,171.78

making pattern of 300x300 mm square 3 mm deep

Providing and fixing 18 mm thick gang saw cut, mirror polished,

premoulded and prepolished, machine cut for kitchen platforms,

vanity counters, window sills , facias and similar locations of

required size, approved shade, colour and texture laid over 20

mm thick base cement mortar 1:4 (1 cement : 4 coarse sand),

joints treated with white cement, mixed with matching pigment,

epoxy touch ups, including rubbing, curing, moulding and

polishing to edges to give high gloss finish etc. complete at all

8.2.2 Granite stone slab of colour black, Cherry/Ruby red

52 Providing edge moulding to 18mm thick marble stone counters,

Vanities etc. including machine polishing to edge to give high

gloss finish etc. complete as per design approved by Engineer-

53 Extra for fixing marble /granite stone over and above

corresponding basic item, in facia and drops of width upto 150

mm with epoxy resin based adhesive including cleaning etc.

54 Extra for providing opening of required size & shape for wash

basins/ kitchen sink in kitchen platform, vanity counters and

similar location in marble/Granite/stone work including

necessary holes for pillar taps etc. including moulding, rubbing

and polishing of cut edges etc. complete.

Digitally signed by JAYA

55 Designing, fabricating, testing, installing and fixing in position

Curtain Wall with Aluminium Composite Panel Cladding, with

open grooves for linear as well as curvilinear portions of the

building , for all heights and all levels etc. including:

(a) Structural analysis & design and preparation of shop

drawings for pressure equalisation or rain screen principle as

required, proper drainage of water to make it watertight

including checking of all the structural and functional design.

(b) Providing, fabricating and supplying and fixing panels of

aluminium composite panel cladding in pan shape in metalic

colour of approved shades made out of 4mm thick aluminium

composite panel material consisting of 3mm thick FR grade

mineral core sandwiched between two Aluminium sheets (each

0.5mm thick). The aluminium composite

panel cladding sheet shall be coil coated, with Kynar 500 based

PVDF / Lumiflon based fluoropolymer resin coating of approved

colour and shade on face # 1 and polymer (Service) coating on

face # 2 as specified using stainless steel screws, nuts, bolts,

washers, cleats, weather silicone sealant, backer rods etc

(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with

Hot Dip Galvanised with serrations and serrated washers to

arrest the wind load movement, fasteners, SS 316 Pins and

anchor bolts of approved make in SS 316, Nylon separators to

prevent bi-metallic contacts all complete required to perform as

per specification and drawing The item includes cost of all

material & labour component, the cost of all mock ups at site,

cost of all samples of the individual components for testing in an

approved laboratory, field tests on the assembled working

curtain wall with aluminium composite panel cladding, cleaning

and protection of the curtain wall with aluminium composite

panel cladding till the handing over of the building for

occupation. Base frame work for ACP cladding is payable under

the relevant aluminium item.s The Contractor shall provide

curtain wall with aluminium composite panel cladding,

having all the performance characteristics all complete , as per

the Architectural drawings, as per item description, as specified,

as per the approved shop drawings and as directed by the

Engineer-in-Charge. However, for the purpose of payment, only

the actual area on the

external face of the curtain wall with Aluminum Composite Panel

Cladding (including width of groove) shall be measured in sqm.

up to two decimal places.

Extra for stone work for wall lining on exterior walls of height

more than 10 m from ground level for every additional height of

57 Providing and fixing dry cladding upto 10 metre heights with

30mm thick gang saw cut stone with (machine cut edges) of

uniform colour andsize upto 1mx1m, fixed to structural steel

frame work and/ or with the help of cramps, pins etc. and

sealing the joints with approved weather sealant as per

Architectural drawing and direction of Engineer-in-charge. (The

steel frame work, stainless steel cramps and pins etc. shall be

paid for separately).

8.20.1 Red sand stone - 30mm thick gang saw cut stone 84.26 SQM 2336.56 1,96,878.38

Digitally signed by JAYA

58 Providing and fixing structural steel frame (for dry cladding with

30 mm thick gang saw cut with machine cut edges sand stone)

on walls at all heights using M.S. square/ rectangular tube in the

required pattern as per architectural drawing, including cost of

cutting, bending, welding etc. The frame work shall be fixed to

the wall with the help of M.S. brackets/ lugs of angle iron/ flats

etc. which shall be welded to the frame and brick wall with

cement concrete block 1:2:4 (1 cement :2 coarse sand :4

graded stone aggregate 20 mm nominal size) of size

300x230x300 mm, including cost of necessary centring and

shuttering and with approved expansion hold fasteners on

CC/RCC surface, including drilling necessary holes. Approved

cramps/ pins etc. shall be welded to the frame work to support

stone cladding, the steel work will be given a priming coat of

Zinc primer as approved by Engineer-in-charge and painted

with two or more coats of epoxy paint (Shop drawings shall be

submitted by the contractor to the Engineer-in-charge for

approval before execution). The frame work shall be fixed in

true horizontal & vertical lines/planes. (Only structural steel

frame work shall be measured for the purpose of payment,

stainless steel cramps shall be paid for separately and nothing

extra shall be paid).

59 Providing and fixing adjustable stainless steel cramps of

approved quality, required shape and size, adjustable with

stainless steel nuts, bolts and washer (total weight not less than

260 gms), for dry stone cladding fixed on frame work at suitable

location, including making necessary recesses in stone slab,

drilling required holes etc complete as per direction of the

8.22 Engineer-in-charge. 169.00 No. 344.52 58,223.52

60 Steel work welded in built up sections/ framed work, including

cutting, hoisting, fixing in position and applying a priming coat of

approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates

and similar works

61 Providing and fixing false ceiling at all height including providing

and fixing of frame work made of special sections, power

pressed from M.S. sheets and galvanized with zinc coating of

120 gms/sqm (both side inclusive) as per IS : 277 and

consisting of angle cleats of size

25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm,

at 1200 mm centre to centre, one flange fixed to the ceiling with

dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts,

other flange of cleat fixed to the angle hangers of 25x10x0.50

mm of required length with nuts & bolts of required size and

other end of angle hanger fixed with intermediate G.I. channels

45x15x0.9 mm running at the spacing of 1200 mm centre to

centre, to which the ceiling section 0.5 mm thick bottom wedge

of 80 mm with tapered flanges of 26 mm each having lips of

10.5 mm, at 450 mm centre to centre, shall be fixed in a

direction perpendicular to G.I. intermediate channel with

connecting clips made out of 2.64 mm dia x 230 mm long G.I.

wire at every junction, including fixing perimeter channels 0.5

mm thick 27 mm high having flanges of 20 mm and 30 mm

long, the perimeter of ceiling fixed to wall/partition with the help

of rawl plugs at 450 mm centre, with 25mm long dry wall screws

@ 230 mm interval, including fixing of gypsum board to ceiling

section and perimeter channel with the help of dry wall screws

of size 3.5 x 25 mm at 230 mm c/c, including jointing and

finishing to a flush finish of tapered and square edges of the

board with recommended jointing compound , jointing tapes ,

finishing with jointing compound in 3 layers covering upto 150

mm on both sides of joint and two coats of primer suitable for

12.45 board, all as per manufacturer’s specification and also including -

12.5 mm thick tapered edge gypsum plain board conforming to

IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Digitally signed by JAYA

62 Providing and supplying aluminium extruded tubular and other

aluminium sections as per the architectural drawings and

shop drawings , the aluminium quality as per grade 6063 T5 or

T6 as per BS 1474,including super durable powder coating of

60-80 microns conforming to AAMA 2604 of required colour and

shade as approved by the Engineer-in-Charge. ( The item

includes cost of material such as cleats, sleeves, screws etc.

necessary for fabrication of extruded aluminium frame work.

Nothing extra shall be paid on this account).The weight of

aluminium extruded section shall be taken for purpose of

63 Designing, fabricating, testing, protection, installing and fixing in

position semi (grid) unitized system of structural glazing (with

open joints) for linear as well as curvilinear portions of the

building for all heights and all levels, including: (a) Structural

analysis & design and preparation of shop drawings for the

specified design loads conforming to IS 875 part III (the system

must passed the proof test at 1.5 times design wind pressure

without any failure), including functional design of the aluminum

sections for fixing glazing panels of various thicknesses,

aluminium cleats, sleeves and splice plates etc. gaskets,

screws, toggles,nuts, bolts, clamps etc., structural and weather

silicone sealants,flashings, fire stop (barrier)-cum-smoke seals,

microwave cured EPDM gaskets for water tightness, pressure

equalisation & drainage and protection against fire hazard

(b)Fabricating and supplying serrated M.S. hot dip galvanised

/Aluminium alloy of 6005 T5 brackets of required sizes,

sectionsand profiles etc. to accommodate 3 Dimentional

movement for achieving perfect verticality and fixing structural

glazing system rigidly to the RCC/masonry/structural steel

framework of building structure using stainless steel anchor

fasteners/ bolts, nylon seperator to prevent bimetallic contacts

with nuts and washers etc. of stainless steel grade 316, of the

required capacity and in required numbers. c) Providing and

filling, two part pump filled, structural silicone sealant and one

part weather silicone sealant compatible with the structural

silicone sealant of required bite size in a clean and controlled

factory / work shop environment, including double sided spacer

tape, setting blocks and backer rod, all of approved grade,

brand and manufacture, as per the approved sealant design,

within and all around the perimeter for holding glass. d)

Providing and fixing in position flashings of solid aluminium

sheet 1 mm thick and of sizes, shapes and profiles, as required

as per the site conditions, to seal the gap between the building

structure and all its interfaces with curtain glazing to make it

Digitally signed by JAYA

(e) Making provision for drainage of moisture/ water that enters

the curtain glazing system to make it watertight, by

incorporatingcurtain glazing to make it watertight.principles of

pressure equalization, providing suitable gutter profiles at

bottom (if required), making necessary holes of required sizes

and of required numbers etc. complete. This item includes cost

of all inputs of designing, labour for fabricating and installation of

aluminium grid, installation of glazed units, T&P, scaffolding and

other incidental charges including wastages etc., enabling

temporary structures and services, cranes or cradles etc. as

described above and as specified. The item includes the cost of

getting all the structural and functional design including shop

drawings checked by a structural designer, dully approved by

Engineer-in-charge. The item also includes the cost of all mock

ups at site, cost of all samples of the individual components for

testing in an approved laboratory, field tests on the assembled

working structural glazing as specified, cleaning and protection

till the handing over of the building for occupation. In the end,

the Contractor shall provide a water tight structural glazing

having all the performance characteristics etc. all complete as

required, as per the Architectural drawings, as per item

description, as specified, as per the approved shop drawings

and as directed by the Engineer- in-Charge.

. Note:-1.The cost of providing extruded aluminium frames,

shadow boxes, extruded aluminium section capping for fixing in

the grooves of the curtain glazing and vermin proof stainless

steel wire mesh shall be paid for separately under relevant

items under this subhead. However, for the purpose of

payment, only the actual area of structural glazing (including

width of grooves) on the external face shall be measured in

sqm. up to two decimal places.Note:-2. The following

performance test are to be conducted on structural glazing

system if area of structural glazing exceeds 2500 Sqm from the

certified laboratories accreditated by NABL(National

Accreditation Board for Testing and Calibration Laboratories),

Department of Science & Technologies, India. Cost of testing is

payable separately. The NIT approving authority will decide the

necessity of testing on the basis of cost of the work, cost of the

test and importance of the work. Performance Testing of

Structural glazing system Tests to be conducted in the NABL

accredited lab or by any other accreditation body which

operates in accordance with ISO / IEC 17011 and accredits labs

as per ISO/ IEC 17025.

1. Performance Laboratory Test for Air Leakage Test (-50pa to -

300pa) & (+50pa to +300pa) as per ASTM E-283-04

testing method for a range of testing limit 1 to 200 mVhr

2. Static Water Penetration Test. (50pa to 1500p) as per

ASTME- 331-09 testing method for a range up to 2000 ml.

3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA

501.01- 05 testing method for a range upto 2000 ml

4. Structural Performance Deflection and deformation by static

25.2 air pressure test (1.5 times design wind pressure without any 14.21 SQM 3107.30 44,154.71

Digitally signed by JAYA

64 Providing, assembling and supplying vision glass panels (IGUs)

comprising of hermetically-sealed 6-12- 6 mm insulated glass

(double glazed) vision panel units of size and shape as required

and specified, comprising of an outer heat strengthened float

glass 6mm thick, of approved colour and shade with reflective

soft coating on surface # 2 of approved colour and shade, an

inner Heat strengthned clear float glass 6mm thick, spacer tube

12mm wide, dessicants, including primary seal and secondary

seal (structural silicone sealant) etc. all complete for the

required performances, as per the Architectural drawings, as

per the approved shop drawings, as specified and as directed

by the Engineer-in-Charge. The IGUs shall be assembled in the

factory/ workshop of the glass processor.(Payment for fixing of

IGU Panels in the curtain glazing is included in cost of item

No.25.2) For payment, only the actual area of glass on face # 1

of the glass panels (excluding the areas of the grooves and

weather silicone sealant) provided and fixed in position, shall be

measured in sqm. (i)

Coloured tinted float glass 6mm thick substrate with reflective

soft coating on face # 2, + 12mm Airgap + 6mm Heat

Strengthened clear Glass of approved make having properties

as visible Light transmittance (VLT) of 25 to 35 %, Light

reflection internal 10 to 15%, light reflection external 10 to 20 %,

shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2

degree K etc. The properties of performance glass shall be

decided by technical sanctioning authority as per the site

65 Extra for openable side / top hung vision glass panels (IGUs)

including providing and supplying at site all accessories and

hardwares for the openable panels as specified and of the

approved make such as heavy duty stainless steel friction

hinges, min 4 -point cremone locking sets with stainless steel

plates, handles, buffers etc. including necessary stainless steel

screws/ fasteners, nuts, bolts, washers etc. all complete as per

the Architectural drawings, as per the approved shop drawings,

as specified and as directed by the Engineer- in- Charge.

66 Providing and fixing double scaffolding system (cup lock type)

on the exterior side of building/structure, upto 25 metre height,

above ground level, including additional rows of scaffolding in

stepped manner as per requirement of site, made with 40mm

dia M.S. tube, placed 1.5 metre centre to centre, horizontal &

vertical tubes joint with cup & lock system with M.S. Tubes, M.S.

tube challis, M.S. clamps and staircase system in the

scaffolding for working platform etc. and maintaining it in a

serviceable condition for execution of work of cleaning and/ or

pointing and/ or applying chemical and removing it thereafter.

The scaffolding system shall be stiffened with bracings, runners,

connecting with the building etc, wherever required, if feasible,

for inspection of work at required locations with essential safety

features for the workmen etc., complete as per directions and

approval of Engineer-in-charge.

Note:- (1) The elevational area of the scaffolding shall be

for payment purpose. (2) The payment will be made once only

execution of all items for such works.

67 Providing and fixing MS Laser Cut Decorative Screen Panel

made out of Mild Steel sheet of thickness 3 mm, cut in approved

geometric/design pattern using CNC laser cutting machine,

including necessary framing with MS square hollow sections

(50X50 mm ), complete welding, grinding, edge finishing,

surface preparation, zinc primer + powder coating (minimum 80

microns thickness) of approved shade and make, including

fixing in position with necessary fasteners, anchors, supports,

complete in all respect as per direction of Engineer-in-charge.

Digitally signed by JAYA

NAME OF WORK :- Renovation of Training Centre Rooms, Dining Hall, Kitchen,

PLUMBING INTERNAL ESTIMATE ( Guard Room )

Sl. No. Description Amount

1 Sanitary Installation 37,164.15 17,024.00

NAME OF WORK :- Renovation of Training Centre Rooms, Dining Hall, Kitchen, External Facade and Gate at L&D Centre NALCO, Bhubaneswar

PLUMBING INTERNAL ESTIMATE ( Guard Room )

S.No. DSR '19 Description Qty. Unit DSR-Rate Amount

Sub Head – I Sanitary Installation

1 17.2.1 Providing and fixing white vitreous china pedestal type water closet (European type

W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including

flush pipe, with manually controlled device (handle lever), conforming to IS : 7231,

with all fittings andfixtures complete, including cutting and making good the walls

and floors wherever required :W.C. pan with ISI marked white solid plastic seat and

2 17.7 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32

mm C.P. brass waste of standard pattern, including painting of fittings and brackets,

cutting and making good the walls wherever require:

3 17.7.3 White Vitreous China Wash basin size 550x400 mm

with a pair of 15 mm C.P. brass pillar taps

4 NSI-1 Providing and fixing white vitreous china wash basin under counter basin, with C.I.

concealed type brackets fixed to walls with GI rag bolts or approved fasteners etc., including

32 mm CP brass waste coupling, including painting of fittings and brackets, cutting and

making good the walls wherever required all complete (Granite counter top will be

measured and paid separately under relevent item): as per approved make and decision of

engineer-in-charge

5 NSI-2 Providing and fixing CP brass auto closing system basin pillar tap / hand wash of

Jaquar PRS - 001 or Equivalent as approved by Engineer- In Charge

6 Providing and fixing CP brass single lever basin mixer without popo with 450mm long

NSI-3 braided hose (connection pipe) basin pillar tap of Jaquar LYR-38001B or Equivalent as 0 each 7802.75 - 0

approved by Engineer- In Charge.

7 Providing and fixing 32mm C.P brass bottle Trap of approved quality & make as per the

direction of engineer-in-incharge.

8 17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved

quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass 1 Sqm 1351.78 1,351.78

screws and washers complete.

9 17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings

17.28.2 Flexible pipe

1.15 17.35 Providing and fixing soil, waste and vent pipes :

17.35.1.3 Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 5 meter 1108.09 5,540.47

1.16 17.38 Providing and fixing bend of required degree with access door, insertion rubber washer 3

mm thick, bolts and nuts complete.

17.38.1.3 Hubless centrifugally cast (spun) iron epoxy coated inside & outside I.S. 15905 0 each 577.99 -

17.39 Providing and fixing plain bend of required degree.

17.39.1.3 Hubless centrifugally cast (spun) iron pipe epoxy inside & outside IS: 15905 5 each 362.32 1,811.62

17.40 Providing and fixing heel rest sanitary bend

17.40.1.2 Sand cast iron S&S as per IS - 3989 0 each 455.35 -

17.42 Providing and fixing double equal plain junction of required degree

17.42.1.3 Hubless centrifugally cast (spun) iron pipe epoxy inside & outside IS: 15905 0 each 757.04 -

17.43 Providing and fixing single equal plain junction of required degree with access door,

insertion rubber washer 3 mm thick, bolts and nuts complete.

17.43.1.2 sand cast Iron S&S as per IS: 3989 0 each 761.26 -

1.21 17.44 Providing and fixing single equal plain junction of required degree

17.44.1.3 Hubless centrifugally cast (spun) iron pipe epoxy inside & outside IS: 15905 0 each 601.96 -

1.22 17.56 Providing and fixing terminal guard:

17.56.1.3 Hubless centrifugally cast (spun) iron pipe epoxy inside & outside IS: 15905 0 each 418.69 -

1.23 17.57A Providing and fixing shielded coupling for Hubless centrifugally cast iron pipes

17.57A.1.1 S S 304 grade coupling with EPDM rubber gasket 5.00 each 425.75 2,128.74

1.24 17.59 Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron

pipes of diameter :

Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and

fittings with two coats of synthetic enamel paint of any colour such as chocolate

grey, or buff etc. over a coat of primer (of approved quality) for new work :

17.65.1 100 mm diameter pipe 0 meter 67.64 -

1.26 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron

(spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1

cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of

cutting holes and making good the walls etc. :

17.37.1 100 mm diameter pipe 0 each 302.8491071 -

Providing and fixing G.I. soil / waste pipes complete with G.I. fittings and clamps, i/c cutting

and making good the walls etc.

18.10.4 32 mm dia. nominal bore 5.00 metre 558.08 2,790.38

18.10.5 40 mm dia. nominal bore 5 metre 673.86 3,369.32

18.10.6 50 mm dia. nominal bore 5 metre 828.90 4,144.49

1.28 Providing and fixing trap of self cleansing design with screwed down or hinged grating with

17.60 or without vent arm complete, including cost of cutting and making good the walls and floors

17.60.1 100 mm inlet and 100 mm outlet

17.60.1.3 Hubless centrifugally cast (spun) iron epoxy

coated inside & outside as per IS:15905

1.29 18.77 Cutting holes up to 15 x 15 cm in R.C.C. floors and roofs for passing drain pipe etc.

and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 ( 1

Cement : 2 course sand : 4 graded stone aggregate 20 mm nominal size ) , including

finishing complete so as to make it leak proof.

1.30 NSI-4 Providing & fixing in position GI 100x50 elbow floor drain including cost of cutting and

making good the walls and floors wherever required.

Providing and fixing 125 mm dia S/S grating (with or without hole)for floor or Nahani

1.32 Providing and fixing soap dish holder from wall of standard shape with fittings of approved

quality with all complete.

1.33 NSI-7 Providing and fixing soap dispenser with glass bottle from wall of standard shape

with fittings of approved quality with all complete.

NSI-8 Providing & fixing 600 mm towel rail long stanless steel from wall face with

concealed fittings arrangement of approved quality with all complete.

18.65 Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth

1.35 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 0 each 117.42 -

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP

brass screws with concealed fittings arrangement of approved quality and colour.

17.73.2 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88

mm, weighing not less than 190 gms.

1.37 12.22 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4

(1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C.

sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse 2 each 257.12 514.25

sand) and a coat of neat cement, rounding the edges and making and finishing the outlet

NAME OF WORK :- Renovation of Training Centre Rooms, Dining Hall, Kitchen, External Facade and Gate at L&D Centre NALCO, Bhubaneswar

PLUMBING INTERNAL ESTIMATE ( Guard Room )

S.No. DSR '19 Description Qty. Unit DSR-Rate Amount

1.38 12.41 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS

: 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap

for thermal expansion,

(i) Single socketed pipes.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for

12.42 unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing

with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

12.42.1 Coupler

12.42.3 Single tee with door

12.42.6 Shoe (Plain)

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised -

PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S.

screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1

cement : 4 coarse sand) and making good the wall etc. complete.

Supplying and fixing of HDPE pipe (PE grade 63 - PN-8 ) confirming to IS 14333-1996

chemical waste pipes jointed with rubber ring with good quality lubricant with fittings

inclussive of all necessary specials like bends, tees, offsets,junctions etc laid under

1.41 NSI-9 floor/under ceiling/on walls with suitable clamps and specials curing, necessary chasing,

jointing and restoring to original conditions, testing etc. including all other incidental charges

etc. complete for successful completion of work as per specifications, and as directed by

Engineer -in- Charge.

a) 110 mm outer dia 5 metre 1543.00 7715

b) 50 mm outer dia 5 metre 558.00 2790

1.42 NSI-10 Providing & fixing in position upvc P"or S" trap of self cleaning design of following sizes

for the embedded areas Making proper connection with chemical sealent joint , cutting

chase / hole in floors /slabs and bringing the same in proper condition in cement concrete 0 each 627.00 -

1:2:4 mix complete as required. including cost of cutting and making good the walls and

floors wherever required.

Providing & Fixing water cooler wth stainless steel having storage capacity of 80 liter &

cooling capacity 60 liter / hour with Reverse osmosis system & ultra voilet membrane TDS

reduction 90% having automatic back wash system with filteration unit & all other required

accessories complete in all respect as per direction of the engineer in charge .

Sub Head – II Water Supply

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making

good the walls etc.

Internal work – Exposed on wall.

18.10.2 20 mm nominal outer dia Pipes 5 metre 362.53 1,812.67

18.10.3 25 mm nominal outer dia Pipes 5 metre 461.46 2,307.32

18.10.4 32 mm nominal outer dia Pipes 5 metre 558.08 2,790.38

18.10.5 40 mm nominal outer dia Pipes 0 metre 673.86 -

18.10.6 50 mm nominal outer dia Pipes 0 metre 828.90 -

NSI-12a 65 mm nominal outer dia Pipes 0 metre 1142.07 -

NSI-12b 80 mm nominal outer dia Pipes 0 metre 1344.36 -

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability

for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the

pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step

CPVC solvent cement and the cost of cutting chases and making good the same including

testing of joints complete as per direction of Engineer in Charge.

Concealed including cutting chases and making good the wall etc.

18.8.2 15 mm nominal outer dia Pipes 5 metre 503.77 2,518.83

18.8.3 20 mm nominal outer dia Pipes 5 metre 592.05 2,960.27

18.8.4 25 mm nominal outer dia Pipes 3 metre 715.53 2,146.60

2.3 18.17 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end)

18.17.1A 20 mm dia. nominal bore 1 each 484.85 484.85

18.17.1 25 mm dia. nominal bore 1 each 523.78 523.78

18.17.2 32 mm dia. nominal bore 0 each 612.39 -

18.17.3 40 mm dia. nominal bore 0 each 714.74 -

18.17.4 50 mm dia. nominal bore 0 each 915.76 -

2.4 18.18 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic

floats complete :

18.18.3 25 mm nominal bore 0 each 415.11 -

2.5 NSI-13 Providing and fixing hand held ablution fitting (health faucet) with 1.2 meter long flexible

tube and wall hook, all complete approved engineer-in-charge

2.6 NSI-14 Supply and fixing of 15mm CP brass 2 -Way Bib Cock with wall flange and suitable length

CP brass extension pipe all of approved engineer-in-charge

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS :

12701 marked, with cover and suitable locking arrangement and making necessary holes 1000 per litre 9.27 9,271.43

for inlet, outlet and overflow pipes but without fittings and the base support for tank

2.8 18.51 Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS

standards and weighing not less than 810 gms.

18.51.1 15 mm nominal bore 0 each 581.94 -

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved

2.9 18.52 make conforming to IS:8931.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved

2.10 18.53 quality conforming to IS:8931

18.53.1 15mm nominal bore 4 each 560.5 2242

2.11 18.21 Providing and fixing uplasticised PVC connection pipe with brass unions :

18.21.2 45 cm length

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as

2.13 17.22B approved by Engineer in charge.

(a) 15 mm nominal dia 1 each 6441.114286 6441.114286

Providing , Fixing, testing and commissioning of CP Brass 150 mm x 150 mm Shower

head with wall flange with all accessories as required and making good the walls wherever 1 each 4875 4875

2.14 NSI-15 required.

NAME OF WORK :- Renovation of Training Centre Rooms, Dining Hall, Kitchen, External Facade and Gate at L&D Centre NALCO, Bhubaneswar

BILL OF QUANTITIES FOR ELECTRICAL WORKS ( MAIN GATE )

Non-DSR- DSR- Non-DSR-

S.No DESCRIPTION UNIT Quantity RATE AMOUNT AMOUNT

I SUB HEAD (I) :- INTERNAL WIRING

1 Point wiring in PVC conduit, with modular type switch :-

1.1 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm

FRLS PVC insulated copper conductor single core cable in surface / recessed

medium class pvc conduit, with modular switch, modular plate, suitable GI box

and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable etc. as required.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell

point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated

1.54 copper conductor single core cable in surface/ recessed PVC conduit, and

earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single

core cable etc. as required.

2 Twin Control Point wiring in PVC conduit, with modular type switch :-

1.9 Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable in surface / recessed medium class pvc conduit, 2 way

modular switch, modular switch, suitable M.S. box and earthing the point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

3 Power plug wiring in PVC conduit (2 x 4 Sq.Mm.) :-

1.12 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper

conductor single core cable in surface/ recessed medium class pvc conduit

alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable

for loop earthing as required. M 30.00 351.89 10,556.79

4 Circuit / Sub main wiring in PVC conduit :-

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of

1.14 FRLS PVC insulated copper conductor, single core cable in surface/ recessed

medium class pvc conduit as required.

6 S/F light plug point Modular type accessories :-

1.31 Supply and fixing of suitable size GI box with modular plate and cover in front on

surface or in recess including providing and fixing 3 pin 5/6 amps modular socket

outlet and 5/6 amps. modular switch, connection etc. as required.

7 S/F power plug point modular type accessories :-

1.32 Supply and fixing of suitable size GI box with modular plate and cover in FRLSont

on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps

modular socket outlet and 15/16 amps. modular switch, connection etc. as

required. Each 2.00 617.39 1,234.79

8 2.18 Supplying and fixing 20 amps, 240 volts, SPN, industrial type socket outlet, with 2

poles and earth metal enclosed plug top along with 20 amps. "C" curve, SP MCB

in sheet steel enclosure, on surface or in recess, with chained metal cover for the

socket outlet, and complete with connections, testing and commissioning etc. as

9 S/F modular type electronic fan regulator :-

1.25 Supply and fixing two module stepped type electronic fan regulator on the

existing modular plate switch box including connections but excluding modular

plate etc. as required. Each 1.00 388.77 388.77

10 S/F modular type blanking plate :-

1.26 Supply and fixing modular blanking plate on the existing modular plate & switch

box excluding modular plate as required. Each 1.00 42.14 42.14

II SUB HEAD (II) :- DISTRIBUTION BOARDS & MCB's

1 2.3 Supplying and fixing following way, single pole and neutral, sheet steel,

MCB distribution board, 240 V, on surface/ recess, complete with tinned

copper bus bar, neutral bus bar, earth bar, din bar, interconnections,

powder painted including earthing etc. as required. (But without

MCB/RCCB/Isolator)

2.3.2 8 way , Double door Each 1.00 2710.84 2,710.84

Digitally signed by JAYA

2.3.3 12 way , Double door Each 0.00 2439.02 -

4 2.14 Supplying and fixing following rating, double pole, (single phase and neutral), 240

volts, residual current circuit breaker (RCCB), having a sensitivity current upto

30 mA in the existing MCB DB complete with connections, testing and

commissioning etc. as required.

5 2.10 Supplying and fixing 5 amps. to 32 amps. rating, 240 volts `C' series, miniature

circuit breaker (MCB)suitable for inductive load of following poles in the

existing MCB DB complete with connections, testing and commissioning etc.

6 Supplying & fixing single pole, blanking plate in the existing MCB DB complete

etc. as required. Each 1.00 13.70 13.70

1 Supplying and fixing following rating, Single/ double/ three pole, 230/ 415 volts,

MCB "C" curve in the existing MCB DB complete with connections, testing and

commissioning etc. as required.

NDSR 40 amps DP MCB Each 0.00 1012.00 -

NDSR 63 amps DP MCB Each 1.00 1121.00 1,121.00

III SUB HEAD (III) :- MISCELLANEOUS

1 2.21 Providing and fixing M.V. danger notice plate of 200mmx150mm made of mild

steel, atleast 2mm thick and vitreous enamelled white on both sides and with

inscription single red colour on FRLSont side as required. Each 1.00 283.41 283.41

2 1.38 Supplying and fixing call bell/buzzer suitable for single phase, 230 volts,

complete as required. NOS 1.00 104.30 104.30

3 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for

10.18 ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5

DSR- mm thick M.S. sheet with its top surface hacked for proper bonding,

2019 top lid shall be screwed into the cast iron/ M.S. sheet box by means of

(Civil) 3.3 mm dia round headed screws, one lock at the corners. Clamp shall

be made of 12 mm dia M.S. bar bent to shape as per standard drawing. Each 1.00 181.48 181.48

IV SUB HEAD(IV):-INTERNAL LIGHTING FIXTURES & FANS

SUPPLY OF LIGHTING FIXTURES

1 Supply of 15W SURFACE MOUNTED LED with all accessories as per standard

Supply of 15W WALL BRACKET LED BULB with all accessories as per standard

Supply of 20W SURFACE MOUNTED LED TUBE with all accessories as per

standard item. Each 1.00 916.00 916.00

Supply of 18W SURFACE MOUNTED LED TUBE with all accessories as per

standard item. Each 0.00 1494.00 -

SUPPLY OF CEILING & EXHAUST FANS

5 19.1 Brush Less Direct Current (BLDC) Fan with Remote

Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less

Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal(Aluminium

alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope,

copper winding, steel/Al body. Power Factor not less than 0.9, Service Value

(CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD

(Total Harmonic Distortion) less than 10%, remote (preferably mobile app based)

for speed control and all remaining accessories including safety pin, nut bolts,

washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega

ohm, suitable for 230 V, 50 Hz, single phase AC supply Ceiling Fan compliant to IS

374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated

copper conductor single core cable and earthing etc. as required.

1200mm, service value ≥ 6.0 CM/Min/Watt, air

delivery 210 CM/Min (Minimum) Nos 1.00 2876.25 2,876.25

6 Supply of AC 230/250 volts, 50 HZ exhaust fans including providing nuts, bolts,

mounting FRLSame and other accessories etc. Complete as required (Such as

Ventil Air - DX White or Equivalent).

NDSR 300 mm sweep 900 rpm Nos 1.00 2800.00 2,800.00

ERECTION OF LIGHTING FIXTURES AND FANS

Digitally signed by JAYA

1 1.41 Installation, testing and commissioning of pre-wired, flourescent fitting / compact

fluorescent fitting of all types, complete with all accessories and tubes etc. directly

on ceiling / wall, including connection with 1.5 sq. mm. FRLS PVC insulated,

copper conductor, single core cable and earthing etc. as required.

2 1.45 Installation, testing and commissioning of ceiling fan including wiring the down rod

of standard length (upto 30 cm.) with 1.5 sq. mm. FRLS PVC insulated, copper

conductor, single core cable, including providing and fixing phenolic laminated

sheet cover on the fan box etc. as required. Each 1.00 357.16 357.16

3 1.50 Installation of exhaust fan in the existing opening, including making good the

damage, connection, testing, commissioning etc. as required

4 MR Providing and fixing concealed LED strip lighting in cove, comprising of high quality

flexible LED strip (minimum 14W per meter, warm white/cool white as approved),

including extruded aluminium profile with opal diffuser, complete with driver

(SMPS), connectors, wiring, soldering, fixing inside ceiling groove, testing and

commissioning, complete in all respects as per direction of Engineer-in-charge.

Digitally signed by JAYA