PROVN OF LIVING ACCN / SHED FOR GUARD / SENTRIES AT TCP OF DHANA MIL STN.

Amount

Excavating in trenches not exc 1.5 Mtr wide & not exc 1.5 Mtr depth for foundation etc or for shafts, wells, cesspits, manholes etc and getting out Hard/dence soil, complete all as specified and directed.

Material & Labour for PCC 1:4:8 type D-2 (with using 40mm graded stone aggregate) in foundation filling and mass concrete, complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point, complete all as specified and directed.

Returning, filling in trenches including spreading, levelling, watering and well ramming in layer n. exc 25 mm all as specified and directed by Engineer-in-Charge.

Material & Labour for Mild steel bars 10mm dia TMT bar and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Material & Labour for Mild steel bars 6mm to 8mm, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Material & Labour for Mild steel bars 5mm and over upto and including 10mm dia in stirrups spaces and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for fair finished surfaces, complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surface complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for fair finished surface complete all as specified and directed.

Formwork to chullah hoods, chajjas, troughs and similar items including edges fair finished surface complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surface complete all as specified and directed.

Material & Labour for RCC M25 as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc. basement slabs, under-reamed piles and mass concrete, complete all as specified and directed.

Material & Labour for RCC M25 as in Columns, pillars, piers, posts and struts complete all as specified and directed.

Material & Labour for RCC M25 as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Material & Labour for RCC M-25 as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Material & Labour for RCC M25 as in chejjas, complete all as specified and directed.

Material & Labour for cement concrete Type B1 1:2:4 (20 mm graded aggregate) in lintels upto 1..5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, complete all as specified and directed.

Material & Labour for Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement Mortar 1:6, complete all as specified and directed.

Material & Labour for brick work with sub class ‘B’ bricks straight or curved on plan exc 6 m mean radius built in CM 1:4 all as specified and directed by Engg-In-Charge.

Material & Labour for 15 mm thick rendering on other than fair faces of brick work or concrete surfaces of wall in cement mortar 1:6 for finished even and smooth (without using extra cement), complete all as specified and directed.

Material & Labour for 15mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces using integral water proofing compound 3% by weight of cement and finishing the surface even and smooth without using extra cement complete all as directed and directed. Note:- WPC shall be measured and paid separately.

Supply only integral water proofing compound complete all as specified & directed.

Material & Labour for 5mm thick rendering in CM (1:3) on concrete surfaces, finished even & smooth (without using extra cement), complete all as specified and directed.

Material & Labour for preparation of new plastered surfaces of ceiling including cornices, pilasters etc and applying three coat of white wash complete all as specified and directed.

Material & Labour for two coats of Oil bound distemper including preparation of newly plastered wall surface over 1.50 mm thick wall care putty etc complete all as specified and directed.

Material & Labour for preparing new plaster surfaces walls including chajjas, facias etc. and applying two coat of weather proof acrylic exterior paint (100% Acrylic) over a coat of primer including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

Material & Labour for Pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

Supply & Fix 2nd class hard wood factory made 35mm thick plain framed pannelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Supply & Fix 2nd class HW 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares (without sash bars ), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats, complete all as specified and directed.

Supply & Fix galvanised steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.8mm and fixed with tinned tacks or galvanized wire staples or wooden bead complete all as specified and directed.

Material & Labour for preparation new or previously untreated surfaces of wood and wood based material of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Material & Labour for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer, complete all as specified and directed.

Supply & Fix MS butt hinges of 100 mm size cold rolled mild steel medium weight, ISI marked complete all as specified and directed.

Supply & Fix 200mm size mild steel barrel tower bolt stone enameled black with bright bolt ISI marked complete all as specified and directed.

Supply & Fix 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

Supply & Fix 300mm mild steel, ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and as directed.

Supply & Fix 150mm size Extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed.

Providing and fixing ECO-4000 series pre-coated double rebated openable window or ventilator made out of galvanised steel colour coated/powder coated (base steel as per IS 513 of 'D' quality galvanised as per IS 277 with zinc of 120 gm/Sqm) with total thickness of coating 0.58 microns finished painted with polyester paint of 12 to 16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with polyester powder up to 50-60 microns thick outer frame section 72x55 mm, centre mullion section 72x50 mm, shutter section 47x20 mm, fly mesh section 40x20 mm and the fixed glass beading section 12x12 mm outer frame and mullions shall consist rebate for glazed shutter, fly mesh and 20 mm provision for gaurd bars/grills, the section cut to length miter jointed with corner brackets, center mullions fixed with mullion cap, stay handles, latch 2 Nos of heavy duty stainless steel pivot hinges per shutter and paneled with 5 mm thick pain float glass and stainless steel (304 grade) mesh for fly mesh shutter fitted with EPDM (Ethyl Propylene Diamine Monomer ) gaskets including fixing window with concrete/stone or brick masonry wall by means of self expanding sleeves and driving MS electroplated 80 mm long bolt into the sleeves through frames (Minimum 4 nos for 1600mm high windows, 3 Nos for 1200 mm less window and 2 nos in ventilator ), including 10 mm square bars welded to 6x12 mm flat at a distance 125 mm c/c etc as per direction of Engineer in Charge. Note:- Refer TD No CELZ/C-TD/102 sheet 1/2 and 2/2.

Material & Labour for hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

Material & Labour for 100mm thick cement concrete type D-2, 1:4:8 using 40mm graded stone aggregate in floor sub base, complete all as specified and as directed.

Material & Labour for 25 mm thick cement concrete in flooring type B1, 1:2:4 (20 mm graded aggregate) screed bed below floor tile, complete all as specified and as directed.

Material & Labour for Non-skid ceramic colour tiles7 to 8 mm thick, (square/rectangular), area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of the tiles over and including 15 mm thick screed bed in cement sand mortar 1:4, complete all as specified and as directed.

Material & Labour for Granite (of any type) tiles 20mm thick machine cut, in, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing including 15 mm thick screed bed in cement sand mortar 1:4 complete all as specified and directed.

Material & labour for rendering 15 mm thick in cement mortar 1:4 over RCC Roof mixed with water proofing compound @ 3% by weight of cement or manufacturer instruction complete all as specified and as directed. (Note:- water proofing compound shall be measured and paid separately as supply only)

Material & labour for ponding test by filling 75 mm deep water over roof treatment by making necessary arrangement to fill the complete Roof slab at least for 72 hrs complete all as specified and directed.

Material & labour for preparing RCC roof surfaces with wire brush drying and cleaning to remove all foreign materials and washing with water to remove loose particle and applying APP membrane HMHDPE 3 Kg plain (thickness 2.1 mm) (total weight of the finished membrane not less than 3.0 kg/ sqm ± 5 % per sqm) confirming to IS 16540: 2017 of following operation complete all as specified and directed:- (a) Applying a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25⁰C, 0.87-0.89 kg/ litre and viscosity 70-160 cps, laying over the primer coat using Butane Torch and sealing all joints, overlapping etc. as per Annex D of IS 16540: 2017 (b) Applying hot blown grade bitumen 85/25 @ 1.20 Kg/Sqm over primer. (c) Laying of polymeric water proofing membrane of weight not than 3 kg/Sqm (d) Applying a coat of hot blow grade bitumen 85/25 @ 1.20 kg/Sqm over APP membrane. (e) Applying aluminium paint in two coats @ 100gm/sqm in each coat of finished membrane surface complete all as specified and directed.

INTERNAL ELECTRIFICATION:- Material & labour for point wiring with 1.5 Sqmm (nominal area) single core PVC insulated 1100 Volts, grade multi stranded (FR-LSH) copper conductor unsheathed cable in and including PVC rigid non metallic conduit medium grade not less than 20mm dia ISI marked and fittings and accessories concealed in walls/roof/ ceiling with suitable size of sunk type cast iron or pressed steel terminal box for mounting of modular switches, sockets, fan regulator etc with modular white cover plate with frame for suitable module as per site requirements and one green colour cable of 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed as earth wire up to common earth and connected to earth including cutting chase and making good to disturbed surfaces of wall with cement mortar 1:3 including necessary plaster and pointing in cement mortar 1:3 with white wash/distemper/other paintings of following, complete all as specified and directed:- (Note:- Cost of cutting chase and making good shall be included in the quoted rate.) Make:- Havells/Finolex/Polycab (a) One light point controlled by one way, one switch SP 230 Volts

(b) One fan point or wall mounted fan controlled by one way, one switch SP 230 Volts

(c) One 3/5 pin 5 Amp socket outlet point controlled by one way, one switch on same board.

(d) One 3/5 pin 5 Amp socket outlet point controlled by one way one switch on independent board.

(e) One 5 pin, 15 amps socket controlled by Independent 15 Amps switch but with cable 2.5 sqmm.

Supply & Fix modular switch 1 way 16 Amp, 1 module, complete all as specified and directed.

Supply & Fix modular socket 6 Amp/16 Amp, 2/3 pin combined, 2 module complete all as specified and directed.

Supply & Fix modular switch 6 Amp/10 Amp, 2/3 pin combined, 1 module complete all as specified and directed.

Supply & Fix modular socket 6 Amp, 2/3 pin combined 2 module complete all as specified and directed

Supply & Fix ceiling rose, 3phase/PVC/Polycarbonate, isolated body, 3 pin surface, white /any shade, three terminals. Make :- Anchor/Leader/SSK

Supply & Fix MCB distribution board steel sheet, enclosures powder coated fitted with bus bar, neutral link, earth bar din rail conforms IS-8822:96 and EIC 898-96, 240 volts double door when MCB SPN 8 way, 200 amps rated bus bar to be used, complete all as specified and directed.

Supply & Fixing of MCB in DB's/ Isolator of the following rating complete all as specified and directed. (a) MCB SPN 40 Amps, curve 'C' breaking capacity 10 kA.

(b) MCB SP 6- 32 Amps, curve 'C' breaking capacity 10 kA.

Supply & Fix LED tube light fitting (separate box fitting and LED rod) acrylic linear tube (1x 18 watt), 230V for single LED light fitting & rod (1 x 18W LED) bar professional CW 6500 K cover channel in box fitting, bipin holders, LED power driver, connector block, etc complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling rose complete all as specified and directed. Make:- Bajaj /Havells/ Philips

Supply & Fix LED light fitting 1x9W/1X10W bulkhead luminaries including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

Material & labour for earthling complete with GI earth plate electrode 60 cm x 60 cm x 6.30 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connected to GI lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electric plate No 3 of SSR Part-I connected to continuous earth wire on main switch board all as specified or indicated and testing on completion including provision of earth wire protection by 15 mm dia medium grade GI pipe and watering pipe shall be 20 mm bore, medium grade including excavation & earth work, PCC pit with RCC cover, charcoal salt funnel, GI wire up to 7.5 mtrs length complete all as specified and directed.

Supply & Fix ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC), complete all as specified and directed.

Supply & Fix 25 watts LED building security light fitting including suitable bracket and nut bolts etc complete all as specified and directed.

siddhant construction

d k suppliar