SPECIAL REPAIR TO BLDG NO T-35, T-47, T-48 ALONGWITH CERTAIN PROVN WORKS OF B/R AND E/M AT AF STATION DADRI AND AOR OF GE (AF) FARIDABAD

Amount

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer-in-Charge.

S&F joist channel angle, tee section, bars , MS plate all structrual steel work fixed in purlin rafter cleat, support etc incl welding, riveting etc conf to Fe-410 Gde E-250 complete all as specified and directed by Engineer-in-Charge.

Dismantling plain or corrugated steel sheeting any gauge, thickness, including Naintal or similar pattern roof coverings etc complete all as specified and directed by Engineer-in-Charge.

S&F pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/clading to wall, molding/folding in circular/semicircular of any position and height fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

S&F pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/clading to wall, molding/folding in circular/semicircular of any position and height fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/ slabs/ blankets any thickness including cover fillets complete all as specified and directed by Engineer-in-Charge.

S&F 6 mm thick Asbestos cement plain building boards, fixed to timber framework with screws complete all as specified and directed by Engineer-in-Charge.

S&F interlocking aluminium powder coated snap grid consists of main Tee runners of size 38mm x 25mm x 1.00 mm spaced 1200mm centre to centre and cross Tee of size 25mm x 25mm x1.00mm, 1200 long spaced between the main Tee at 600mm centre to centre to form a grid of 1200mm x 600mm and provide a secondary cross Tee 25mm x 25mm x 1.4mm (of length 600mm) to be interlocked of the centre of 1200mm x 600mm panel to form a grid of 600mm x 600mm and wall angle 25mm x 25mm x 1.5mm . Aluminium alloy extruded section shall be aluminium anodized ( minimum 15 micron) and shall conform to IS 733, IS 1285 and IS 737, and providing and fixing with Hangers of 4mm dia GI (upto 1200mm length ) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x 3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long size of grid 600 x 600mm complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster from brick or stone masonry or concrete surfaces and hacking for key and scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

M&L 15 mm thick rendering in cm 1:6 on brick surfaces or concrete surfaces finished even and smooth without using extra cement

M&L for preparation of new plastered surfaces and applying two coats of cement base paint on walls over a coat of alkali resistant priming paint all as specified.

M&L two coat of oil bound distemper after 3mm Birla/JK wall care putty on new plastered surfaces including necessary prepararion complete all as specified and as directed by Engr-in-Charge..

Demolition of cement concrete unreinforced in groundfloors and pavings not exc 15cm thickness below or above ground level etc complete all as specified and directed by Engineer-in-Charge.

M&L for providing cement concrete 1:2:4, type B1, using 20 mm graded stone aggregates as in coping complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling or stone flooring including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

M&L PCC 1:2:4 type B-1 using 20mm graded stone agg 40 mm thick complete all as specified and directed by Engineer-in-Charge.

M&L for 600mmx600mmx10 mm thick coloured vetrified Light shade tiles shade as approved flooring( in any pattern) and jointed with neat cement slurry over 15 mm thick cement screed in CM 1:6 and pointed with coloured cement matching with surfaces of tiles as in floor complete all as specified and directed by Engineer-in-Charge.

M&L for 600mmx600mmx10 mm thick coloured vetrified Light shade tiles shade as approved ( in any pattern) in vertical surfaces as skirting and jointed with neat cement slurry over fixed to wall as skirting with 10 mm thik cement sand mortar in CM 1: 4 ,and pointed with coloured cement matching with surfaces of tiles as in floor complete all as specified and directed by Engineer-in-Charge.

M&L for machine cut kota stone slab flooring 20-25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing, moulding on edge and polishing over and including 20mm thick screed bed in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

S&F 12 mm thick Toughened glass partition with one door with All accessories(Suitable stainless steel handle 2 Nos, stainless steel Joint cleats, including Suitabel floor spring and with suitable stainless steel upper framing), including fixed to walls and floors with suitable clips and silicon filling materials complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work built in cement mortar of any description complete all as specified and directed by Engineer-in-Charge.

M & L for brick work with sub class 'B' Bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:4 as in manholes and drain complete all as specified and directed by Engineer-in-Charge.

M&L 15mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:4, complete all as specified and directed by Engineer-in-Charge.

Demolition of Reinforced Cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-Charge.

M&L for RCC 1:2;4 B0 (using of 12.5 mm Stone Aggregate) Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and chajjas complete all as specified and directed by Engineer-in-Charge.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) complete all as specified and directed by Engineer-in-Charge.

M&L for 10 mm dia and over TMT bar cut to length bent to shape required including cranking bending spirally for hoping for columns hooking ends binding with MS wire n.exc 0.9mm or with securing clips etc complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15 mm thick in CM 1:4 on stone masonary or surface other than fair face of brick works etc or similar surfaces etc including with mixing of water proofing liquid of Dr. fixit Qty as per manufactrer instruction complete all as specified and directed by Engineer-in-Charge.

M&L 15 mm thick rendering in cm 1:6 on brick surfaces or concrete surfaces finished even and smooth without using extra cement incl mixing of water proofing liquid of Dr. fixit as per manufactrer instruction complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 10mm thick in CM 1:3 on concrete surface in ceillings etc including with mixing of water proofing liquid of Dr. fixit as per manufactrer instruction complete all as specified and directed by Engineer-in-Charge.

M&L three coat of white wash on new surfaces on ceiling including necessary prepararion complete all as specified and directed by Engineer-in-Charge.

M&L for complete removal of existing treatment by washing, rubbing down and stopping of distempered and painting surfaces etc and applying two coats of oil bound distemper on walls over a coat of 3 mm thick wall care putty complete all as specified and directed by Engineer-in-Charge. (Note - work shall be got executed through skilled representative of manufacture company)

M&L for preparation of old previously decorated surfaces by brooming down or steel wire brushes, scrapping down smoke soot, moulds, efflorescent salts etc and applying one coat of white wash on walls complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old decorated wooden surfaces and applying one coat of synthetic enamel paint over 10 cm in width or girth complete all as specified and directed by Engineer-in-Charge.

All as per item No 34 above but on steel surfaces complete all as specified and directed by Engineer-in-Charge.

M&L precast cement concrete type-B1 1:2:4 by using 20 mm graded crushed broken stone aggregate, in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings set in cement mortar 1:4 or complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frame n.exc. 1.50 sqm each with shutters (with out taking off shutter from the frame) and removing from the site complete all as specified and directed by Engineer-in-Charge.

All as per item 37 above but exc 1.50 sqm and n.exc 4.00 sqm each (with out taking off shutter from the frame) and removing from the site complete all as specified and directed by Engineer-in-Charge.

S&F in repair Framed work as in doors, for door frames or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing (Fe-410- W(Gde?E-250)Gde) qualtycomplete all as specified and directed by Engineer-in-Charge.

S&F 30 mm thick flush shutters, solid core construction with block board core and ply wood face panels commercial type on both side. Exposed edges of shutter to be provided with 6mm thick teak wood lipping. The thick ness of lipping shall be 12mm for sides on which hinges are to be provided complete all as specified and directed by Engineer-in-Charge.

S&F 35 mm thick factory made second class hard wood factory made glazed and skelton shutters open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc. Size of members of shutters as specified in IS-1003 supplied and fitted to the chowkats complete all as specified and directed by Engineer-in-Charge.

S&F in repair Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing complete all as specified and directed by Engineer-in-Charge. (Note:- Door frame shall bewater proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life)

S&F sheet glass 3 mm thick ordinary quality and fixed with oil putty / wooden beads in square n.exc. 0.5 sqm in each pane complete all as specified and directed by Engineer-in-Charge.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples fixed including a coat of French blue paint complete all as specified and directed by Engineer-in-Charge.

S&F aluminium anodized barrel tower bolts of extruded section 150 mm long complete all as specified and directed by Engineer-in-Charge.

S&F mild steel sliding door bolts plate type stove enamelled black with bright bolts not less than 12mm dia with and including a minimum of 6 bolts and nuts four on bolts plate and two on staple plate in wooden shutters and welded/riveted in steel shutters (250 mm long) complete all as specified and directed by Engineer-in-Charge.

S&F butt hinges medium weight cold rolled mild steel 100 mm size complete all as specified and directed by Engineer-in-Charge.

S&F 150 mm size mild steel pressed handle oval type stove enamelled black complete all as specified and directed by Engineer-in-Charge.

S&F Aluminium handles cast type anodized of 150 mm size complete all as specified and directed by Engineer-in-Charge.

S&F mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old decorated wooden surfaces and applying one coat of synthetic enamel paint over 10 cm in width or girth complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L preparation of new steel surfaces over 10 cm in width or girth and applying two coat of synthetic enamel paint over one coat of red oxide complete all as specified and directed by Engineer-in-Charge.

S&F Powder coated Aluminium doors shutters air tight with natural anodized alunimium frame with on or more rebate partly glazed and partly panelled of with hollow profile PVC panelling of thickness 12mm (all aluminium member Top, bootom, vertical & middle of shutter made of size 82.55x44.45x1.60mm thick including necessary jointing cleats, glazing clips, 5mm thick tinted glass, rubber packing with anodized aluminium beading /glazing clip size 19.00x17.30x0.70mm, wt 0.097 Kg/RM of both side and fixing aluminium fittings i.e aluminium hinges 100mm three numbers, handles 200mm long two numbers, tower bolts 150mm two numbers and mortic lock with 06 lever fitting shoiuld be (ISI marked) complete all as specified and directed by Engineer-in-Charge. (Rates will also include making good floor /wall jambs of doors/ windows surface with plaster and match with existing finishes)

S&F powder coated aluminium frames for doors,windows,ventilators & partitions with one or more rebates including jointing cleat for fixing and suitable aluminium poweder coated handles, tower bolts and door stopers including fixing to floor with suitable screws/fasteners in partiton etc. complete all as specified and directed by Engineer-in-Charge.

M&L for powder coated anodised aluminium sliding window & ventilator in two track of size of track frame 63.50 x 38.5 x 2.0 mm thick fixed on a powder coated and Aluminium window frame of size 63.5 x 46 x 2 mm and Aluminium shutters (2mm thick of aluminium material) including provision of 5.5 mm thick tinted glass fixed with powder coated aluminium snap and rubber beading.Stainless steel wire mesh of 0.36 mm dia with aperture of 1.40mm fixed with aluminium F chanal complete all as specified and directed by Engineer-in-Charge. Note. (a) Stainless steel wire mesh of 0.36 mm dia with aperture of 1.40mm fixed with aluminium F chanal (b) Aluminium anodised spring to be locking device 02 Nos of 100 mm long in each window. (c) Aluminium eye hook/stopper in each leaf. (d) Amininium anodised handle 02 Nos in each window 100mm size. (e) Aluminium grills to be measured seperatly.

S&F powder coated aluminium anodized grill of 6/7 mm dia rod square, rectangular, circular or similar type of shape, fixed with channel 38 mm x 12 mm x 1.30 mm (Sec No 8778) complete all as specified and directed by Engineer-in-Charge.

S&F in repair for double action floor spring hudraulically regulated make up of minimum 150mm thick aluminium alloy sheet foundation box, main body with stainless steel cover governing pivot made of brass otaher parts made of mild steel heavy duty and fixed complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel water tubing and connection incl cleaning for refixing or removal to stores for following bore complete all as specified and directed by Engineer-in-Charge. :- (a) 15mm

All as per item No 59 20mm complete all as specified and directed by Engineer-in-Charge

S&F GI tubes medium grade with all fitting and fixed concealed complete to walls and ceiling or laid in floor in following bore of tube complete all as specified and directed by Engineer-in-Charge :- (a) 15mm

All as per item No 61 20mm complete all as specified and directed by Engineer-in-Charge

S&F in repair 20 MM Gun-metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe and fixed in repair and complete all as specified and directed by Engineer-in-Charge

S& Fix in repair 15 mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in repair and complete all as specified and directed by Engineer-in-Charge

S&F sinks in repair made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repair vetrious china wash hand basin, white flate back size 550 mm X 400 mm including cutting for and pinning in ends of barakets or erecting stand complete all as specified and directed by Engineer-in-Charge

S&F PVC connection 15 mm bore 450 mm in length complete all as specified and directed by Engineer-in-Charge

S&F in repair PVC Waste pipe 32 mm dia complete all as specified and directed by Engineer-in-Charge

S&F in repair brass CP waste coupling (half or full threaded) of 32 mm size complete all as specified and directed by Engineer-in-Charge

S&F in repair brass CP soap dish of approved quality complete all as specified and directed by Engineer-in-Charge

S & F in repair brass CP tower rail, 600mm long of consisting three rod , brackets complete all as specified and directed by Engineer-in-Charge

S&F rotational moulded polyethylene water storage tanks (cylinderical, vertical with closed top) of 500 Ltrs capacity hoisted and fixed in position complete all as specified and directed by Engineer-in-Charge as per SSR Pt- I

S/F in repairs 15 mm angle valve chromium plated with wall flange and fancy type with high pressure screwed down and with CP flange of same make complete all as specified and directed by Engineer-in-Charge

S&F in repair bib tap long body 15mm, fancy type complete all as specified and directed by Engineer-in-Charge

S&F in repairs Brass CP centre hole WHB mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge

S&F in repair PVC flush bend 32mm dia with two Nos check nuts for conencting low level flushing cistern to European type water closet or India type water closet incl cement joint complete all as specified and directed by Engineer-in-Charge

S&F in repair 10 Litre PVC low level flushing cistern complete with syphonic action type, white, with inlet, ball valve, float and handle connecting to ITWC/ETWC and fixing on walls with brackets complete all as specified and directed by Engineer-in-Charge

S&F in repairs for Vitreous China squatting pan,"Orissa" pattern,size 580 X440 mm white,withintegral foot rests (excluding flushing cistern and flush pipe) including connection to flushing pipe anti syphonage pipe etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs cast iron Nahani trap with grating including jointing to waste pipe, fixed in cement concrete 1:2:4, type B-1, using 20 mm graded stone aggregate, dia of outlet 100 mm complete all as specified and directed by Engineer-in-Charge

S&F door closer hydraulically regulated designation No 2, aluminium (Die cast) body, universal type suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 Kg fixed & repair complete all as specified and directed by Engineer-in-Charge

S&F in repair Curtain rod Stainless steel 25 mm dia 1mm thick with pairs of fixing fancy type brackets heave grade, Fancy type supprting stops heavy grade, rollers including screws with required accessories and finishing the surface with existing wall surface etc complete all as specified and directed by Engineer-in-Charge

M&L for coloured printed non skid tiles area of each tile exceeding exc 0.06 sqm but n.exc 0.11 sqm in floors etc set and jointed with neat cement slurry pointed with colour cement to match the floor, and including 15 mm thick screed bed cement mortar in CM 1:4 and including the chipping of the existing PCC floor complete all as specified and directed by Engineer-in-Charge

All as per item No.83 above but each tile exceeding 0.18 Sqm but not exc. 0.36 Sqm complete all as specified and directed by Engineer-in-Charge

M&L for digital design glazed ceramic tiles in vertical surface of size of each tile 300 x 450/300 x 250 mm and 7 to 8 mm thick fixed to wall with 10 mm thik cement sand mortar in CM 1: 4 , set and joint in neat cement slurry and pointed in white or coloured cement to match the same complete all as specified and directed by Engineer-in-Charge

Dismantling of stone slabs & tiles of any description or thickness (except ceramic tiles) in floors, aprons etc laid bedded & pointed in any mortar complete all as specified and directed by Engineer-in-Charge

M & L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing types nd including 20mm thick screed bed in CM 1:4 complete all as specified and directed by Engineer-in-Charge

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50 m in depth for manholes & sewage lines and getting out in soft/loose soil complete all as specified and directed by Engineer-in-Charge

M&L concrete bed to 100 mm bore drain pipes in cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregates including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed by Engineer-in-Charge

S & F in repair PVC 110 mm (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with clamps and for sewage line complete all as specified and directed by Engineer-in-Charge

M&L cement concrete type C-2 1:3:6 ( 40 mm graded aggregate) as in foundation, filling and mass concrete complete all as specified and directed by Engineer-in-Charge

M&L PCC 1:2:4 type B2 as in surface channels and drains & benching of manholes and finishing even and smooth with out using extra cement complete all as specified and directed by Engineer-in-Charge

Returning filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm complete all as specified and directed by Engineer-in-Charge

Removing excavated materials to a distance not exceeding 50 Mtr and depositing where directed at a level not exceeding 1.5 Mtr above the starting point complete all as specified and directed by Engineer-in-Charge

Cutting into existing manholes for connecting new drains, making good to pipes and rendering, cutting out existing benching for & forming branch channel (1/2 round or 3/4 Section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required, Internal dia of pipe 150mm complete all as specified and directed by Engineer-in-Charge

Cutting into existing manholes for connecting new drains, making good to pipes and rendering, cutting out existing benching for & forming branch channel (1/2 round or 3/4 Section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required, Internal dia of pipe 200 mm complete all as specified and directed by Engineer-in-Charge

M&L PCC 1:4:8 type D.2 (40mm graded agg) as in fdn filling and mass concrete complete all as specified and directed by Engineer-in-Charge

Providing, precast cement concrete1:2:4 type B1 (20 mm graded aggregate) in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces etc. and setting in mortar complete with joints to match complete all as specified and directed by Engineer-in-Charge

M&L for mild steel TMT bars 10 mm dia and over cut to length bent to shape and required including cranking bending spirally for hoping for columns hooking ends and binding with and including mild steel wire n. less than .9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge

Rounding to edges of stone slabs, granite one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed by Engineer-in-Charge

M&L for coloured printed non skid tiles area of each tile exceeding exc 0.11 sqm but n.exc 0.18 sqm in floors etc set and jointed with neat cement slurry pointed with colour cement to match the floor, and including 15 mm thick screed bed cement mortar in CM 1:4 and including the chipping of the existing PCC floor complete all as specified and directed by Engineer-in-Charge

S&F Plates (plain or chequered) channels, square cut or notched ordinary and counter sunk) forming holes, without any attachmen etc conf to Fe-410 Gde E-250 complete all as specified and directed by Engineer-in-Charge

S & F steel window & supply and fixing steel window with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with guard bars glazing dovetailed or welded complete all as specified and directed by Engineer-in-Charge

All as per item No 103 but without glazing bars complete all as specified and directed by Engineer-in-Charge

S&F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; similar work conforming to Fe 290 or Gde-E- 165 complete all as specified and directed by Engineer-in-Charge

S&F MS work as in vertical member of steel structure,MS pipe, MS square tube, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by Engineer-in-Charge

Demolition & breaking up drain pipes (salt glazed stone ware, AC or reinforced concrete) set in cement mortar, internal dia of pipe 150 mm complete all as specified and directed by Engineer-in-Charge

All as per item No 107 here-in-before but bore of pipe 200 mm complete all as specified and directed by Engineer-in-Charge

M & L 150 mm internal dia salt glazed stone ware drain pipes laid in trenches and jointed complete all as specified and directed by Engineer-in-Charge

All as per item No 109 here-in-before but bore of pipe 200 mm complete all as specified and directed by Engineer-in-Charge

M&L concrete bed to 150 mm bore drain pipes in cement concrete 1:3:6 type C-2 using 40mm graded stone aggregated including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed by Engineer-in-Charge

All as per item No. 111 here in before but bore of pipe 200 mm complete all as specified and directed by Engineer-in-Charge

Demolition of cement concrete of any description and in any position as in bed of drain pipes etc complete all as specified and directed by Engineer-in-Charge

M & L for Machine pressed precast concrete interlocking paver block any shape and size with grey cement and coloured pigment confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade over 30 mm thick coarse sand complete all as specified and directed by Engineer-in-Charge

M&L for Sand filling under floors or in foundation including watering and consolidating complete all as specified and directed by Engineer-in-Charge

Dismantling of unserviceable chain link fencing fixed with any post in any position complete all as specified and directed by Engineer-in-Charge

Excavation in post holes or similar holes each n.exc 0.50 cum, getting out and returning, filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25 cm, watering and removing surplus soil to a distance n.exc 50 mtr and making good to surface in soft and loose soil complete all as specified and directed by Engineer-in-Charge

S&F in repair posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc complete all as specified and directed by Engineer-in-Charge

Supply only chain link MS galvanised fencing of any size or type as complete all as specified and directed by Engineer-in-Charge

Fixing only chain link fencing including line wire, any mesh, size and type to any of standards, rails, straining blots etc including provision of blinding wire complete all as specified and directed by Engineer-in-Charge

M&L mild steel work such as round bars fixed independently as fillets for securing chain link fencing including all necessary drilling for bolting etc confirming to Fe-410-0 or Fe-310-0 complete all as specified and directed by Engineer-in-Charge

Supply only mild steel bolts (Machine made) with hexagonal or square head at one end and screwed the other end with washeres and one hexagonal or square nuts length of bolt exc 10cm long and dia of shank 11 to 15mm complete all as specified and directed by Engineer-in-Charge

S&F framed works Fe-290 (Gde E-165) as in doors, gates, of angles or other sections with gusset plates, rails,braces, pintal etc complete drilled for fixing of steel sheeting or other covering.Doors etc to be prepared for hanging or sliding with and including either hooks or hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides)and hanging ,also fastening and fixing including sliding door bolts complete all as specified and directed by Engineer-in-Charge

Cleaning of manhole upto 1 m depth and removal of sludge silt/liquid/mud/sand/water etc in foul position to out side the MOD land complete all as specified and directed by the Engineer-in-Charge.

All as per item No 4 here-in-before but exceeding 1m and not exceeding 2m in depth complete all as specified and directed by Engineer-in-Charge.

Dewatering/desilting of septic tanks,soak wells etc cleaning of all sludge,silt residue of both organic and inorganice nature by manual labour or mechnical scrappers etc and disposal of the same out side the defence land incl dumping the material to any depth complete all as specified and directed by Engineer-in-Charge.

M&L for Earthing complete with copper plate 60×60cm ×3.15mm thick electrode, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normalground level, connected to 20×3mm copper strip as earthing lead all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion complete all as specified and directed by Engineer-in-Charge.

M&L for Installation, testing, commissioning of Reverse Osmosis based Water Treatment Plant-Capacity 250 ltrs/hr One running & One standby of 250 LPH capacity including filters, cleaning materials,transportation complete all as specified and directed by Engineer-in-Charge. a) Raw water pump -2.5 -3.0 Kg/cm2 (Make - Kirloskar/ Crompton) b) Pressure Sand Filter for Coarse Filteration - 1000 ltrs/Hr c) Pressure Vessel 1054 frp Vertical Cylindrical Type d) Membrane Housing Type Horizontal Pressure vessel model 4040 Discharge Capacity 500lph @ 110 meter head Pressure Gauge- 0-500 psig c) Anti- scalant dosing system d) Fine Filtration e) RO High Pr pump, RO Housing, RO membrane f) Electronic control panel :- (KB Control panel)

M&L for Rotational moulded polye thylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I of capacity 1000 Ltr Make : Sintex (or) Equvilent

M&L for Rotational moulded polye thylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed by Engineer-in-Charge in SSR Part I of capacity 500 Ltr

M&L for Electrical wire, Raw water line and Fittings 20 Mtr complete all as specified and directed by Engineer-in-Charge.

M&L for One Skilled Operator for complete operating RO plant including replacement of filters, cleaning, back washing, smoth functioning of plant for one Month complete all as specified and directed by Engineer-in-Charge.

Supply, and fixing bus bar chamber 4 Way outdoor type factory made out of CRCA sheet dust & vermin proof , front opening door having locking arrangement totally enclosed weather proof, antirusted powder coated painted including aluminium Bus Bar of 200 Amps rating bus size 45 cm long x 50mm wide x 15mm thick, 440 volts, 3 Phase 4 wire having suitable gap to connect the cables of size 95 Sqmm 3.5 core and bus mounted on suitable type of insulators incl coloured insulating sleeve on each complete with bottom removable gland plates for inccomming and out going cables, bus chamber mounted on MS angle stand made of MS angle 50mm x 50 mm x 5 mm and should having minimium 45 Cm gap below bus chamber incl necessary PCC foundation work complete all as specified and directed by Engineer-in-Charge.

Supply, laying, testing and connecting cable under ground XLPE insulated screened PVC bedded, galvanised strip or wire armoured, electric power cables ( heavy duty) with 1100 Volts grade with starndedard aluminium conductor inclusive connected with thimbles, nutt bolt by crimping tool etc complete of size 95 sq mm 3.5 core complete all as specified and directed by Engineer-in-Charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for laying of cables/ poles or foundation etc getting out complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed by Engineer-in-Charge.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engineer-in-Charge.

M&L for sand cushioning with a layer of sand 80mm thick before laying of cable and 150mm thick after laying of cable to trenches complete all as specified and directed by Engineer-in-Charge.

Supply of brick sub class B laid dry in trenches over the cable ad joining each other widthwise for cable protection complete all as specified and directed by Engineer-in-Charge.

S&F sheet metal enclousers MCB type DB suitable VTPN 4 way 200 Amp rated bus bar double door type complete all as specified and directed by Engineer-in-Charge.

S&F MCCB 4 Pole .415 V. fixed type, 100 Amps with breaking capacity 16 KA , 240 V complete all as specified and directed by Engineer-in-Charge.

S&F MCB SP capacity 6-32 Amps , 240 V complete all as specified and directed by Engineer-in-Charge.

M & L for Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanisedusing galvanised iron strip 32×6mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion complete all as specified and directed.

M & L for submain wiring with two runs of PVC insulated 1100 volts graded multistranded, copper conductor of size 2x4.0 sq. mm + 1x2.5 sq. mm earth wire in PVC 20mm dia conduit complete all as specified and directed by Engineer-in-Charge.

M & L for submain wiring with two runs of PVC insulated 1100 volts graded multistranded, copper conductor of size 2x6.0 sq. mm + 1x4.0 sq. mm earth wire in PVC 20mm dia conduit complete all as specified and directed by Engineer-in-Charge.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20Amps for AC complete all as specified and directed by Engineer-in-Charge.

36SHRI RADHEY ASSOCIATES

GARG CONSTRUCTION CO

NAVEEN KUMAR TYAGI