Renovation of Co-Ordination Building in JUT Campus Namkum, Ranchi

Amount

Taking down ceiling any type and refixing them after repair with departmental material with 15M lead and disposal unserviceable materials with all leads all complete as per direction of E/I.

Taking down chaukhat in doors including stacking serviceable materials within 15M, lead and disposal unserviceable materials with all leads all complete as per direction of E/I.

Taking down old door and window shutters including stacking serviceable materials within 15M, lead and disposal unserviceable materials with all leads all complete as per direction of E/I.

Dismantling old plaster and pointing in cement or lime and raking out joints to 15mm depth, watering and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Water' proofing for Old and New Roof Slab :- Providing, and laying water· proofing treatment on roof slab by applying two Component, factory designed, ready to ·use, acrylic modified . flexible material applied with , brush, roller or spray for water proofing coating_ as per manufacturer specifications with following steps :- (a) surface preparation:- Providing . and cleaning of concrete surface to remove dust, oil, grease including removal of existing loose paint / coating, and cement la1tance by cleaning with compressed air & water jet including all materials, labour, tc;,ols complete. Ponding test to be done after plugging all outlets and to be checked from soffit to identify seepage, leakage. On identification of seepage, cement grouting to. be done with non shrink expanding admixture of Sika India Pvt. Ltd. / MYK Schomberg I pr Fixit/Fosroc or equivalent. Providing and repairing of all corners and joints such as. those between ·the parapet wall and the roof slab etc shall be chamfered with 150 mm X 150 mm fillet of mortar (Cement: sand-1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent. Before chamfering a prime coat shall be given with the slurry of acrylic polymer. Repairing surface irregularities, damaged concrete in base slab, dead cracks if any, with an ·acrylic polymer modified repair mortar including a coat of bonding agent of ·the same with cement slurry including all material, ·labour, tools complete. (b) 1st Coat :- Apply 1st coat of two component acrylic modified, . ready to use, flexible. cementitious material on surface. saturated qry roof and inside wall of· Parapet wall upto 600 mm by brush or -roller. After 1st coat of application, 45 gsm of Fibre glass-cloth. to lay when the first layer is still green. 1st coat ·should be applied @ 1.50 kg/ Sqmt / coat. For the purpose of measurement the entire treated surface will be measured: (c) 2nd coat :- To apply the 2nd coat of two component acrylic modified; ready to use, flexible cementitious material right angle to the 1st coat over the glass fibre la. id surface. 2nd coat should be applied. @O. 7 kg/Sq mt/coat. For the purpose-of measurement the entire treated surface will be measured." After three days of drying the 2nd coat , the rail water outlets to be plugged and ponding .-:test to be done for 48 h·ours to identify seepage, leakage .from soffit and if found necessary rectification to be done as p_er satisfaction of EiC. The -Waterproof coating to be protected from damage before screed ·over it. Waterproofing Brand:- s·ika Topseal 109hi / Fosroc Brushbond: RFX / Dr Fixit Pidiffin 2K / MYK Aquafin TG . Product Performance - Chemical Base Part A : Acrylic copolymer, Part B : Specially graded cementitio LJS powder - Density 1.6 kg/I ( mixed density) at+ 27°C Tensile Strength ~2 N/mm2 after 28 days ( with Fibre cloth ) (According to ASTM D 2370) Pullout Bond Strength ~2 N/mm2 (concrete failure) (According to iSO 4624) Siant - Shear Bond Strength ~4 N/mm2 (According to FIP 5.15) Elonga tion at Break ~35°/o without Fibre Cloth and.20% with Fibre Cloth( (According to ASTM D 2370) (d) Protection of treated surface with PCC :- The treated surface should be covered with 25mm/ 50mm PCC of M-20 grade(1 :1.5:3) with proper slope ( 1 :120) towards the rain outlets in alternate panels of 2 mt x 2mt keeping 6 mm gap between the panel joint. Integral water proofing admixture conforming to IS 2645 @ of 100 ml per bag of of cement to be added in the screed concrete(paid separately for this items). All corners shall be chamfered with 150mm X 150 mm fillet. The rain water outlets shall be just levelled with the screed concrete to ensure smooth discharge of water - the peripheral gaps between pvc pipe outlet and concrete surface· should be packed properly with rich concrete and the peripheral mouth to be sealed with moisture insensitive epoxy putty of Sika India Pvt.Ltd. / MYK Schomberg I Dr Fixit/Fosroc. For the purpose of measurement, the entire treated surface will be measured." (e)Groove of PCC surface should be filled with Polysulphide Sealant.(Paid separately). Brand - Sika India Pvt. Ltd. / MYK Schomberg/ Dr Fixit/Fosroc. Warranty for five years .

Covering of treated surface with PCC :-Providing 50mm thick Cement Concrete M20(1:1.5:3) maintaining slope in alternate 2 mt x 2 mt panels with approved quality of stone chips of 20 mm to 6 mm size graded and cleaned sand of F.M 2.5 to 3 Including screening, shuttering and mixing cement concrete in mixer with admixture of integral water proofing and placing in position, striking curing, taxes and Royality all complete as per building specification and direction of E/I. Panels that has been left should be casted next day.There should be_ 6 mm gap between Panels .Brand-Sika. Plastocrate plus, MYK proof WP 1 O,Fosroc-Conplast X4211 C,Dr.fixit Pidiproof LW+ or Equivalent.

Covering of treated surface with PCC :-Providing 50mm thick Cement Concrete M20(1:1.5:3) maintaining slope in alternate 2 mt x 2 mt panels with approved quality of stone chips of 20 mm to 6 mm size graded and cleaned sand of F.M 2.5 to 3 Including screening, shuttering and mixing cement concrete in mixer with admixture of integral water proofing and placing in position, striking curing, taxes and Royality all complete as per building specification and direction of E/I. Panels that has been left should be casted next day.There should be_ 6 mm gap between Panels .Brand-Sika. Plastocrate plus, MYK proof WP 1 O,Fosroc-Conplast X4211 C,Dr.fixit Pidiproof LW+ or Equivalent.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Providing 12mm thick cement plaster (1:8) with clean coarse sand of F.M 1.5 including screening curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M 1.5 including screening curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing & Applying high quality acrylic modified resin based texture of Dholpur/Red sand stone Pattern with anti algae and UV resistance properties to be applied as intermediate finish in desired pattern @ 43.04 kg/10 sqm to form film of 1- 1.5 mm thickness after scrapping and properly cleaning the surface to remove loose particles from the plaster surface, followed by top coating with Premium Acrylic Smooth exterior paint with Silicone additives of required shade by two or more coats @ 1.43 litre/10 sqm, complete as the direction of Engineer -in-Charge.

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortrar (1:3) and jointing with grey cement slurry flush point with cement including rubbing, polishing and cost of curing taxes and royality all complete as per building specification and direction of E/I. with commercial grade colour tiles.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1 :4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Area of slab over 0.50 sqm

Providing and laying double charged vitrified floor tiles in different size (thickness to be specified by the manufacturer) with water absprotion less than 0.08% and conforming to IS:15622/ISO 13006 of approved make in all colour and shades, laid on 20mm thick cement mortrar 1:4 (1 cement : 4 coarse asnd) jointing with grey cement slurry @3.3kg/sqm including groting the joints with cement and matching pigments etc. complete size of tile 600 x 600mm

Providing and laying in position cement concrete of specificed grade excluding the cost of centering and shuttering - all work upto plinth level : 1:1½:3 ( 1 cement : 1½: coarse sand (zone III) : 3 graded stone aggregate 20mm nomninal size)

Providing and laying vitrified paring/industrial tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08% and confirming to IS : 4457:2007, of approved make in all colour and shades, laid on 20mm thick cement mortrar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry %3.3kg/sqm including groutings the joints with white cement and matching pigments etc, complete size of tiles 300 x 300 x 10mm size.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5 mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Frame size 65 x 125 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 30 mm thick

Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R2 series with frame (70 mm & above) x (40 mm & above) & both glazed and fly screen sash (25 mm & above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 metre).

Supplying, fitting and fixing 20 guage G.C.I sheet gate fitted on M.S. Angle frame of size 60 x 60 x 6mm including cost of fabrication, providing necessary locking arrangements with haskal and domny duly fixed in P.C.C (1:2:4) blocks of required size, applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I.

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plasterd surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.

Providing two coats of painting with ready mixed paint of approved shade and make over steel surface including cleaning the surface throughly, scaffolding and taxes all compelte as per building specification and direction of E/I.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized@ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main 'T' at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1 .6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard,manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16 mm thick fire retardant PVC film on the face side and 12 micron metalized polyester on the ack side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.

Supply fitting and fixing good quality,well dressed and well seasoned salwood work in chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preseravative of approved quality on the surface buttling walls and lintels all complete as per building specification and direction of E/I.

Supply fitting and fixing good quality, well dressed and well seasoned teak wood work in choukhat including wedge over all clamps complete including application of two coats of wood preseravative of approved quality on the surface buttling walls and lintels all complete as per building specification and direction of E/I.

Supply fitting and fixing 150 x 20 x 6mm L-Type M.S clamp properly fishtailed, inlcuding makeing holes and setting the including making holes and setting the same in 200 x 125 x 75mm

Supply fittting and fixing 38mm thick good quality, well dressed well seasoned teakwood fully glazed shutters in doors with aluminium fittings such as hinges, sliding doors, bolts, tower bolts, handles or rings hook an deye cleats sand blocks as per schedule and 5.5mm thick plain single glass fitted with teak wood beads taxes all complete as per building specification and directino of E/I.

Supply fitting and fixing 35mm thick solid core type non decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formula dehydes synthetic resin of standered make with aluminium fittings such as hinges, tower bolts, handle, cleats and sand block and taxes all complete as per building specification and directino of E/I.

S/F/F All height door frame pannelling do do all complete job as per building specification and direction of E/I.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Making plinth protection 50mm thick of cement concrete (1:3:6) (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) over 75mm thick bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including necessary excavation levelling and dressing and finishing the top smooth

Providing 150mm wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 125mm appron including cost of earthwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A, flat soling in proper grade and slope at the base, the drain duly plastered in C.M (1:3) with punnign over exposed surface all complete as per building specification and direction of E/I.

Providing one coat of wax polishing with mansion, eaxpol or equivalent approved quality of wax polish over old or new wooden surface including cleaning the surface after removing dirt, scales, smokes, greases and sand papering, including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Carriage of materials on materials on pucca road as truck with loading and unloading from truck and stacking of the materials at work site with all complete as per building specifiction and direction of E/I

(i) Sand lead 8km

(ii) S/ Chips lead 22km

(iii) Bricks

P/P on terrace (at the floor level) polyehylene water storage tank

Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 0.63 mm thick with zinc coating not less than 275 gm/m2

Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 0.80 mm thick with zinc coating not less than 275 gm/m2

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Copuler - 75mm

Copuler - 110mm

Single tee with door - 75 x 75 x 75mm

Single tee with door - 110 x 110 x 110 mm

Bend 87.5" - 75mm bend

Bend 87.5" - 110mm bend

Shoe (Plain) - 110mm

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1 :4 (1 cement : 4 coarse sand} and making good the wall etc. complete.

(i) 75mm dioa

(ii) 110mm dia

Dismantling pucca brick or lime work including stacking servicable metarials in countables stacks within 15M. leads and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment ( excluding the cost of chemical emulsion) :

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.:

Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same.

Supply, Fitting and fixing virterous white glazed earthen ware I.W.C of Parry Hindustan or any other I.S.S approved make with 100mm H.C.I 'p' trap 15 litres C.I pull and let go flushing cistern of names or other I.S.S. equivalent make complete with all fittings C.I or C.C brackets 32 alkathene/P.V.C telescopic flush, pipe about 2M long with one brass coupling and clamps G.I chain and pull including supplying and fixing a pare of viterous white glazed earthenware ware footrest to be fixed in floor 15mm C.I body brass spindle stope cock of weight not less than 50 grams, 15mm P.V.C connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I. 500mm long with 10litre low level PVC Cistern

Supplying fitting and fixing flat back or angular lipped front vireous white glazed earthen ware urinal of 'Hindustan Parry' or any other approved I.S.S make with 5 litre capacity C.I automatic flushing cistern or reliance or any other I.S.S approved make with all fittings with C.I or R.S. brackets standared size G.I flush pipe with fittings clamps, 15mm C.I body brass spindle stop cock of approved quality. Flat back standing corner 600 x 350mm

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore

Providing and laying Double Flanged (screwed / welded) Centrifugally (Spun) Cast Iron, Class B (IS : 1536) : 100 mm dia C.I. Double Flanged Pipe

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Circular shape 450 mm dia

Providing and fixing PTMT grating of approved quality and colour 125 mm nominal dia with 25 mm waste hole

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 32 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

15 mm nominal dia Pipes

20 mm nominal dia Pipes

25 mm nominal dia Pipes

32 mm nominal dia Pipes

40 mm nominal dia Pipes

Supply materials and labour for constructing inspection chabmer of designation class 75B bricks size 750mm deep 600 x 450mm internal dimension having 250mm wall thickness in cement mortrar (1:6) cement plaster (1:6) with 600 x 475mm G.I cover with frames (weight not less than 36kg) along with earth work in excavation and 80mm thick P.C.C (1:3:6) in foundation and refilled all complete job as per specification and direction of E/I.

roviding and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Supply fitting and fixing C.P bras towel rail 20mm x 600mm with bracket container complete wiht all materials as per specification and direction of E/I.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 510x1040 mm bowl depth 178 mm

Special type of C.P bathroom fittings for V.I.P building (JAL, Jaguar, Marc or equivalent makes)(ISI Marked) Sink cock with swinging casted spout

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Single Tee with door 75 x 75 x 75mm

Single Tee with doro 110 x 110 x 110mm

Single tee without door 75 x 75 x 75mm

Single tee with door 110 x 110 x 110 mm

Bend 87.5" dia 75mmb end

Bend 87.5" 110mm bend

shoe (plain) 75mm shoe

Shoe (Plain) 110,mm shoe

Point wiring in PVC Conduit, with modular type switch : wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5sqmm FR PVC insulated copper conductor single core in surface/recessed PVC modular switches modular plate suitable GI Box etc as required Group C

Power plug wiring in PVC conduit (2 x 4 sqmm) :- Wiring for light / power plug with 2 x 4sq.mm FR PVC insulate copper conductor single core cable with surface/recessed PVC conduit, along with 1 NO. 4sq.mm FR PVC insulated copper conductor single core cable for loop earthing etc as required.

Supply and installation of 16" (400mm) wall mounted fan do do all complete job as per building specification and direction of E/I. (BR.Rs.1950.00 + 10%C.P + 5%OHC)

Circuit/Sub-main wiring in PVC conduit :- Wiring circuit/ submain wiring along with earth wire with the following zises FR PVC insulated copper conductor single core cable in surface recessed PVC conduit as required

2 x 2.5sqmm + 1 x 2.5sqmm earth wire

2 x 4.0sqmm + 1 x 1.4sqmm earth wire

2 x 6.0sqmm + 1 x 6.0sqmm earth wire

S/F Modular type electronic fan regulator :- Supply fitting and fixing stepped type elecronic fan regulaytor on the existing modular plate and switch box ijncluding connections but excluding modular plate etc. as required

SITC of floowing rateing LED street light luminare with presrsure die cast housing and toughened glass cover (ip 66 protection) in existing pole/pipe for supply voltage 100 - 270V AC, 50Hz. Luminarie shall be confirm to IS: 10322 part - 5 section 3 and shall be complete dwith all necessary acessories as reuqired :- 2'0" x 2'0" LED Pane light

S/F SP MCB DB: Supplying and fixing of following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland late,interconnections, phosphatized and powder painted including earthing etc. as required (Without MCB/RCCB/ISOLATOR).

8 way double door for PDB (First Floor)

12 way double door for power and light circuit at ground floor

Supplying and fixing the follwing way Three Pole pole and Neutral Sheet steel M.C.B distribution board, 415 volts in recess, completed with tinned copper busbar, neutral bus bar, earth bus bar, din bar, hinged front acrylic cover from MCB Knob detachable gland plate, interconnection including earthing etc. as required(without MCB/RCCB/Isolator). Make-Havells/ Legrand/ Polycab/ C&S/ Hager/ABB / HPL/Anchor

4 way(4+12) Double door Horizontal type for Lighting (GL=1, FF=1) (power=1 nos at GL)

Supply and fixing 6 amps to 32 amps rating 240 volts, 10 KVA "C" curve miniature circuit braker suitable for inductive load of followign poles in the existing MCB DB complete with connections, easting and commissioning etc as required

6/32A Single Pole

32A DP MCB (LIGHTNING)

32A TPN MCB (LIGHTNING)

63A TPN MCB (POWER)

63A DP MCB (POWER)

S/F Rewireable double pole/ TP&N Switch Disconnector: Supplying and fixing following capacity double pole/TP&N sheet metal swich disconnector fuse unit in existing metal board with rewireable types fuses, including drilling holes in metal board, making connections, etc. as required

32 amps, double pole for LDBs

63amps, double pole outings for PDBs

32 amps, TP&N outings for LDBs

63amps, TP&N outing for PDB

200amp, TP&N as incomer

Copper Earth Plate Elecrode:- Earthing with copper plate 600mmx 600mmx 3mm thick including acessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal or cock and salt complete etc. as required.

Providng and fixing 25mm x 5mm G.I strip in 40mm dia G.I pipe from earth electrode including connection with G.I nut, bolt, spring, washer excavation and refilling etc as required.

Providing and Fixing Lightning Conductor Finial : P/F of lighting conductor finial,made of 25mm dia 300mm long GI tube, having single prong at top, with 85mm dia 6mm thick Gl base plate including holes etc. complete as required.(2 nos for Science block 2 nos for Arts block, 2 nos for Library)

GI lightning conductor tape in horizontal run - Providing and fixing of Gl tape 20mm X3mm thick on parapet or surface of wall for lighting conductor etc complete as required.

Providng and fixing G.I lightning conductor tape in Vertical run - Providing and fixing of Gl tape 20mm X3mm thick on parapet or surface of wall for lighting conductor etc complete as required.

MV Cable:- Supply of ISI marked aluminium cable conductor XLPE PVC insulated cable as per IS:7098 armoured, served, sheathed, 1100V grade with Termination and Laying of cable. Make:- Finolex / Polycab / Havells / Mescab/KEI

3.5CX95 sq. mm armoured AL Cable. For JSEB supply.

Laying oof one number PVC insulated and PVC sheathed/XLPE power cable of 1.1KV grade of size excedding 35sqmm but not excedding 95 sqmm direct in ground including excavation and refilling the trenches etcd as required but excluding sand cushioning and protective covering

SITC of floowing rateing LED street light luminare with presrsure die cast housing and toughened glass cover (ip 66 protection) in existing pole/pipe for supply voltage 100 - 270V AC, 50Hz. Luminarie shall be confirm to IS: 10322 part - 5 section 3 and shall be complete dwith all necessary acessories as reuqired :- 120W LED Flood light

S/F DP MCB insolatir :- supplying and fixing following rating, double pole 240 volts isolator in the existing MCB DB complete with connections, testing and commissioning etc as required : 40 amps

LED bulb 9W/10W : Supply and fixing of LED 9W/10W bulb and sccessories as required (Make- Bajaj/Hevells/Phillips_

Supply of metal exhaust fan 12" (300mm) supply of 12" (300mm) 230V AC exhasut fan in the existing opening including making good and damage, connection testing, commissioning etc as required (make - Polar / Bajaj/ Havells/ Crompton)

Air conditioner 2.0 ton 5 star split AC (Inverter type ) IS 1391 Part 1

Air conditioner 1.5 ton 5 star split ac (Inverter type) IS 1391 part I

Coppor tube of size ½" for split AC with 1 to 3 ton capacity including nitride rubber insulation

5 KVA Wall mounted Automatic voltage stablizer from range 140V to 280V

Drain pipe for AC

Outdoor stand for 1 to 1.5 ton split AC

Outdoor stand for2 ton split AC

Silent type D.G. Set of Capacity 50 KVA three phase with AMF Panel IS (IEC-60034-IS:1460IS:13018)

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item -A) and disposal of excavated earth as obtained to a distance upto 50M. including all lifts, levelling, ramming the foundation trenches, removing roots of trees shurbs all complete as per approved design, building specifcation and direction of E/I.

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all completed as per building specification and direction of E/I. (Mode of measurment compacted volume)

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 with floating coat of neat cement in skirting including rounding of junctions with floor, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying in position cement concrete of specificed grade excluding the cost of centering and shuttering - all work upto plinth level : (1:3:6) (1 cement : 3 coarse sand (zone III) : 4 Concrete)

Providing and laying in position specified grade of reinformed cement concrete, excluding the cost of centering shuttering finishing and reinforcement - all work upto plinth level (1:1.5:3) (1 cement : 1.5 coarse sand (zone III) : 3 graded stone aggregate 20mm nominal size)

Centering and shuttering including strutting propping etc and removal of form for : foundation footings base of columns etc for mass concrete

Centering and shuttering including strutting propping etc and removal of form for : columns, pillars, piers, abutments, posts and struts

Centering and shuttering including strutting propping etc and removal of form for : Lintel, beams, plinth beams, girders, bressumers and centilevers

Providing TMT reinforcement of following dia rods as per approved design and drawing including carriage of M.S. rods of (Straight or in coils) to work site, cutting, bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per building specification and direction of E/l.

Providng TOR steel reinforcement of 8mm dia rods as per approved TMT Fe 500 (Only falid for TATA (Tiscon), SAIL, JSPL, Electrosteel Steels LTd. Bokaro and Vizag (RINL)

Providing tor steel reinforcement 10mm dia bars as per approved design and drawing

Providing tor steel reinforcement 12mm, and 16mm dia bars as per approved design and drawing

Providing tor steel reinforcement and 16mm dia bars as per approved design and drawing

Filling in founation trenches and plenth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of founation trenches within a lead of 50M and lift of 1.5M all complete as per building specification and direction of E/I.

Providing 12mm thick cement plaster (1:6) in ceiling with clean coarse sand of F.M 1.5 including screening curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm)

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing primer one coat of red lead paint of approved make over new, steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and · cleaning the surface thoroughly including of scaffolding and faxes all complete as per building specification' and direction of E/1. (Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specification).

Providing two coat of synthetic enamel paint of approved make over new, steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and · cleaning the surface thoroughly including of scaffolding and faxes all complete as per building specification' and direction of E/1. (Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specification).

Providing two coat of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper, scaffolding, curring the taxes all complete as per building specification and direction of E/I.

Chequered terrazo tiles 22 mm thick in floors on 20 mm thick bed of cement mortar (1:4). : Light shade using white cement

Providng and fixing VICTORIA--U.P TEXTILES HANDLOOMS Fabric - polyester Vertical Blinds of Slat Width 100 mm and Slat Thickness 2 mm VICTORIA Unregistered Brand Manufactured by: U.P TEXTILES HANDLOOMS (VICTORIA VERTCAL BLINDv)Product id: 5116877-84129325237

Supply fitting and fixing Jaquar S-Trap Pattern 4 (fi g 3B)(Vitreous China) - WashdownWater Closets Jaquar (SLS-WHT-6851S220PP) Product id: 5116877-96738919636

Supply fittings and fixing Cera Vitreous China Sinks / WashBasins Flat Back and Rectangle Cera (S2020158) Product id:5116877-8464281376

Add 18 % GST (in Basic Rate must fill 12)

Add 1% Labour Cess (in Basic Rate must fill 1)

M/S Raman Construction