Resurfacing of 60m wide service road and Construction of balance work of 60m wide road service road, Greater Noida

Cleaning jungle including up rooting of rank, vegetations grass, push, wood trees and samplings of grith upto 30cms. measured at a height of 1 M. above ground level and removal of rubbish up to a distance of 50M. Out side periphery of area cleared. (SOR-20/259(i))

Same as above 259(i) above but grass only (SOR-20/259(a)

Excavation in foundation in ordinary soil (Loam clay or sand) including lift upto 1.50 M and lead upto 30.00M and including filling watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the engineer incharge upto a distance of 30m from the foundation trenches (where machine con not reach/move) (SOR/251 (A)/4.1.1)

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm. depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres. (DSR-18/16.1)

Granular sub-base with graded material, plant mix method Construction of granular sub-base by providing close graded material, mixing in a mechanical mix plant at OMC, carriage of mixed material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401. MORTH/4.01/401(A)

Wet mix macadam (Plant mix method) Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layers with grader in sub-base/base course on well prepared surface and compacting with vibratory roller to achieve the desired density (MORTH/4.14/406(B))

Brick edging in full brick width and half brick depth including excavation, refilling and disposal of surplus earth lead upto 50 metres.

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (DSR-18/16.7.1)

Providing and applying primer coat with SS1 grade bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means. (MORTH 502/5.01/A(i))

Providing and applying tack coat with bitumen grade of VG-10 using pressure distributor at the rate of 0.50 Kg per sqm on the prepared bituminous surface cleaned with mechanical broom. (MORTH 5.02/503)

Providing and laying dense graded bituminous macadam with Higher capacity batch type HMP using crushed aggregates of specified grading Premixed with bituminous binder VG-30 @4.5% by weight of total mix and filler, transporting the hot mix to work site, laying with hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve to desired compaction as per MoRT & H Specification CLAUSE No 505 complete in all respects (Morth/5.04/505(B))

50mm compacted thickness with bitumen peretration of [email protected]% by weight of total mix. (MORTH-/5.05/505(B))

Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder [email protected]% of mix and filler transporting the hot mix to work site laying with hydrostatic paver finsher with sensor control to the required grade, level and alignment rolling with smooth, wheeled, vibrator and tendom roller to achieve the desired compaction as per MORTH specification clause 507 complete in all respect (MORTH/507(B)/5.05)

40mm compacted thickness with bitumen peretration of [email protected]% by weight of total mix

Road marking with Hot applied Thermoplastic compound with reflectorising Glass beads on Bituminious surface Providing and laying of hot applied thermoplastic compound 2.5mm thick including reflectorising glass beads @250gms per sqm area, thickness of 2.5mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes, Rates are inclusive of all taxes, royalty etc. all T&P/machine material and labour required for proper completion of work. (SOR-2020/New item/Sr.No.19.01)

Labour cess and GST will be paid extra as per Govt. orders.

Please Enable Macros to View BoQ information