Interior work at the office space of IOL at Unit no. F-005, Ground floor, tower F, World Trade Centre, Nauroji Nagar, New Delhi-110029

S NO DESCRIPTION AMOUNT AMOUNT

2.00 SANITARY/ PLUMBING WORKS 12,928.85 1,06,292.00

3.00 ELECTRICAL WORKS 13,89,919.00 18,49,452.00

7.00 WI-FI & LAN WORKS (ACTIVE & PASSIVE) 0.00 57,47,660.00

10.00 FIRE ALARM & PA SYSTEM 0.00 12,22,969.00

13.00 ACESS CONTROL 0.00 2,87,014.00

Total (DSR +MR) 3,00,54,047.09

Digitally signed by SAKET

SCHEDULE OF QUANTITIES-CIVIL

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

1 FLOORING WORKS

CEMENT CONCRETE: Providing and laying in position CEMENT CONCRETE of specified grade exluding the cost of centring and

1.01 shuttering-all work upto plinth level.

4.1.8 1: 4: 8 (1 Cement: 4 coarse sand: 8 graded stone aggregate 40mm nominal size) 13.22 CUM 6812.00 90054.64

RAISED FALSE FLOOR: Providing and fixing removable raised/false access flooring with systemand its components of approved

make for different plenum height with possible height adjustment upto 50mm, comprising of modular loadbearing floor panels

supported on G.I. rectangular stinger frame workand G.I. Pedestal etc. all complete, as per the architectural drawings, as specified

and as directed by Engineer-in-charge consisting of:

(a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm

outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal

head of size 75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the

stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be

fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug.

(b) Stringers system in all steel construction hot dipped galvanized ofrectangular size 570x20x30x0.80mm thick having holes at both

ends for securing the stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions,

the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid

11.54 support for access floor panel, the system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for

electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the Engineer-in-

(c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of

800H grade (FS800H). Access Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64

hemispherical cones. The top and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together

(minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust

protection and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious core mixed with

lightweight foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp

technology upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a Concentrated

Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the panel which is placed on four steel blocks. The

panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all complete as per the

approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of

the panel to ensure the quality of the product.

11.54.2 450mm Finished Floor Height (FFH). 5.88 sq m 5977.35 35146.818

ALUMINIUM SKIRTING: Supply of 100mm Aluminium (Grade 6063) Skirting with 15 micron anodising In Natural Finish. Thickness

1.30 to 1.50mm. Designed to conceal screws. Seamless finish. Complete with Rubber/ PVC Jointers and Gasket.

ENGINEERED WOODEN FLOORING: Supplying and Installation of engineered wooden flooring of total thickness 13 mm -16 mm,

1.04 MR Toplayer PEFC controlled Core board PEFC controlled Backing layer PEFC controlled sources Wood Veneer 2 mm Tongue and 35 sq m 7000.00 245000.00

groove Length Uniclic Width Uniclic Multifit Domestic use Conditions as per direction of engineer in charge.

VITRIFIED TILES: Providing and laying vitrified floor and wall tiles in different sizes (thickness to be specified by the manufacturer)

with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick

1.05 cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white

cement and matching pigments etc., complete.

CARPET TILES: Providing and laying Carpet tiles of Yarn type Eco Solution Q® Nylon (Nylon 6) only; Multi-Level Pattern Loop,

manufactured using 100% solution dyeing process, Tiles of size 23cms x 91cms or equivalent as per direction of EIC and site

requirement with SSP® Soil Protection treatment TM or equivalent containing properties of Stain Repel, with Ecoworx® Tile- 100%

PVC Free/ 100% Bitumen Free/ 100% Recyclable - backing system with recycled content, made from thermoplastic polyolefin

1.06 MR compound with reinforcing layer high-performance environments requiring modular flooring, having tufted yarn weight of 542.5 72.77 sq m 2844.00 206957.88

gsm/sqm and average yarn density of Minimum 9143 oz/cu. yd. or more, Nominal total thickness 5.42 mm minimum, Radiant Panel

class 1 rated (ASTM E648), NBS smoke < 450, Pill test -Passed, Anti Static Property less Than 3.5 kv, Texture Appearance Retention

Rating of 3.5 for Severe Use, Anti Microbial Treatment-Passes (AATCC-174). CRI Green Label Plus is certified for indoor air quality,

including fixing/ installation with Low/ Zero VOC content Adhesive. Impact Sound (ISO 10140-3) 20 dB & Sound absorption (ISO 354)

0.2 Class D.or equilent as per direction of EIC and site requirement

Digitally signed by SAKET

SCHEDULE OF QUANTITIES-CIVIL

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

IPS FLOORING: 52mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12mm thick cement hardener

1.07 11.4 consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed 107.77 sq m 978.45 105447.5565

@ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of

nosing of steps etc. complete.

ITALIAN MARBLE: Providing and laying machine cut, mirror polished, Italian Marble brass brass inlay stone flooring laid in required

pattern in linear portion of the building all complete as per architectural drawings, with 18mm thick stone slab laid over 20mm

1.08 11.51 (average) thick base of cement mortar 1: 4 (1 cement: 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm

including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing

etc. all complete as specified and as directed by the Engineer-in-Charge.

11.51.1 18 mm thick Italian Marble stone slab in all colour and shade 52.22 sq m 6603.35 344826.937

TOTAL FLOORING WORKS 585163.3985 477330.68

2 FALSE CEILING WORKS

GYPSUM BOARD CEILING: Providing and fixing false ceiling at all height including providing and fixing of frame work made of

special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS :

277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre,

one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle

hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate

G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom

wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction

2.01 12.45 perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction,

including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed

to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of

gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including

jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes ,

finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all

as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with

frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but

excluding the cost of painting with

12.45.1 12.5mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) 66 sq m 1355.8 89482.8

WAVE BAFFLE CEILING: To Supply & Install Custom made Vertical curve Polylam Blades Ceilings as per the design intent. The

vertically curve baffle system POLYLAM exhibiting space- delineating characteristics. The system comprises vertically curve baffle

with 75-150mm deep curved rafters manufactured out of 1.2mm Aluminium to provide wave effect. The module for fixing baffle shall

be 150mm centres as per design requirement. The carrier rails run perpendicular to the baffles axis and can be mounted with M6

2.02 MR threaded rods using technical approved fasteners as per EN 13964 standards. The individual baffle lengths between 1200- 2400 mm 10 sq m 8776.00 87760.00

can be selected. Baffles lengths less than 1500mm required two carrier rails mounted at the baffle ends. Baffle longer than 1500mm

require additional carrier rails mounted in the centre. Finish RAL Powder Coated.No Pre Coated products shall be accepted. The

spacing of the grid angles is according to the requirements of DIN 18168 and DIN EN 13964 and quality controlled to ISO 9001:2015

approved by SIS & LEED certification by Indian Green Building council (IGBC).

METAL CEILING: Providing and fixing GI Plain 13- 15mm deep panel upto 6mtr, shall be roll formed out of 0.5mm thick Powder

Coated .The top coat of panel shall be 60 micron polyester coated finish in approved colour. The panel shall be factory cut in up to

6Mtr OR required length. Accessories Detail: Carrier: 63mm deep, made out of 0.6mm thick steel backed with enameled black paint

having cut out to hold on panel in a module of 75mm closed. The joint of two carriers shall be joined by means of carrier splices

maintaining a module of 75mm .4mm dia galvanized rod with special height adjustment butter fly clips made out of SS steel sheet.

The edge profile G.I.shall be matching with the panel.

PERFORATED SQUARE ACOUSTIC CEILING: Providing and fixing suspended Demountable acoustic ceiling in recessed grid

system 300x1200x12.5mm E with Unity 3, square 3.5mm holes, with 0.80 NRC* Material: High Grade Glassfiber Reinforced

2.04 MR Perforated plasterboard with Cleaneo TechnologyBoard type: Ceiling tile Lengthxwidthxthickness: 300x1200x12.5mmEdge: E 10 sq m 3200.00 32000.00

recessed grid system (8mm recess) Perforation: Unity 3, 3.5x3.5 Surface: Water-based acrylic paint Colour: White NCS 0701 Y24R,

closet match to RAL 9003; gloss 5 Attachment: Silhouette 15mm face exposed grid. 100 MM Centre to Centre

Digitally signed by SAKET

SCHEDULE OF QUANTITIES-CIVIL

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

GYPSUM LOUVERED CEILING: 12.5x600x600 high grade, glass-fibre reinforced, acoustic, gypsum panel with acoustic perforation

as Unity 3 - square 3.5x3.5mm c/c 8.33 type U3.The ROLD 12 tiles with Strip shall be screw fixed on min. 60mm wood or steel

furring. The ROLD 12 with strips tiles are with edge B+ and are pre-painted ready for installation on site. ROLD 12 screws, type Torx

15, with white-painted head are used for screw-fixing. The acoustic ROLD 12 tiles are furnished with a grey (white) absorbent felt

backing with an airflow resistance of 330-460 Ns/m³ (DIN 53887).Colour - White, NCS 0701 Y24R, gloss 5 (standard) or re-paintable

at site with water based acrylic paint.Closest match for repainting: NCS 0700/RAL 9003. Paint Type - Waterbased acrylic emulsion

paint including titanium for hygienic indoor climate. Light Reflection: 69.2% according to DIN Norm 5036.Acoustic Property - αw: 0.95;

NRC: 0.90.Fire Class - A2-s1,d0 .Suspension - The ROLD 12 must be screw fixed to furring of 22 mm wood or 60mm steel battens at

ACOUSTIC CEILING: Providing and fixing suspended Demountable acoustic ceiling in recessed grid system -Danoline : Belgravia

300 x 1200 x12.5mm E with Unity 3,square 3.5mm holes, with 0.80 NRC* Material: High Grade Glassfiber Reinforced Perforated

2.06 MR plasterboard with Cleaneo Technology Board type: Ceiling tile Length x width x thickness: 300x1200x12.5mm Edge: E recessed grid 24.19 sq m 3200.00 77408.00

system (8mm recess)

Perforation: Unity 3, 3.5x3.5 Surface: Water-based acrylic paint ,Colour: White NCS 0701 Y24R, closet match to RAL 9003; gloss 5

LINEAR OPEN CELL CEILING: Providing and fixing of Starlum 9 linear cell ceiling made out of Aluminium. The assembled cell

ceiling panels shall be in size of 600x1200mm. The assembled cell ceiling panels shall made out of main blades in 9mm (W) x 40mm

(H) in 1200mm (L), installed at 66.66 mm c.c. and cross connected to secondary blades in 15mm(W) x 37mm (H) in 600mm (L) with

240 mm pitch. The assembled cell ceiling panels are then clipped into U-94 carriers in GMS,coated in black enamelled finished at

1200mm c.c. Wire clips shall hold the cell ceiling panels into the U-94 carriers. Once the U-94 carriers are installed then primary

angles made out of GMS, type U1040 are cross connected to the U-94 carriers at 1200mm c.c. for lateral bracing The whole ceiling

shall be suspended by M6 threaded rods installed at 1200mm c.c. The panels are fully downward demountable / hinged from the

proprietary U 94 carrier section using C 94 spring panels.The system should be in accordance with Material class A2-s1, d0 according

to EN 13501-01 “non-combustible”, as per the Direction of Arch-in-charge. The system will meet fire retardant standards of BS 476:

Part 6 & Part 7. Tolerances according to TAIM, DIN EN 13964 and quality controlled to ISO 9001:2015 approved by SIS, LEED

certification by IGBC.All panel modules must be hinge able through wire clips. Finish of cell ceiling panels: Metallic silver in RAL 9006

& RAL 9016 White White colour.

LOOP CEILING: Providing & fixing LOOP® Type 2 system formed as an open metal ceiling with an open area of more than 50% and

to the flare [5mm] of the perforation pattern [RV-50-40] the ceiling has a three-dimensional visual effect and hides the insight into the

plenum. Bypassing the perforation, the S-shaped sides of the LOOP® interlock both the long and front side joint with a non magnetic

suspension, the elements are installed with a circumferential 1 mm joint, thus compensating tolerances in x and y direction. The non-

magnetic suspension system effectuates a self-alignment of the elements [puzzle effect]. The module size 966x1115x1.0mm GMS is

perforated with 60mm deep drawn holes .The substructure consists of a form perforated L profile [U1040] as a lateral grid which is

suspended from the ceiling with nonius adjustable upper and lower parts or with threaded rods using official approved dowel plugs.

2.08 MR The grid profiles are to be connected together at the ends by means of longitudinal connectors [U 1041] [screw fasteners]. The 10.23 sq m 21780.00 222809.40

spacing of the grid profile is according to the requirements of DIN EN 13964. On profiles angles, C-band raster as secondary profiles

are bolted on by means of C channel hanger bracket with M6 bolts. Only construction parts approved by the manufacturer may be

used. Provide necessary supports, provisions as per the architects / PM’s Instructions. Tolerances according to TAIM, DIN EN 13964

and quality controlled to ISO 9001:2015 approved by SIS.Finish of ceiling is in RAL 9016 white/ RAL 9006 Silver grey powder coated

with minimum 70-80 microns paint thickness. Manufacturer shall have the fully automatic powder coating system with power and free

conveyorize 3mtr/minute capacity. Powder coating plant shall be equipped with latest modern technology with fully automatic inline

Pre-treatment using nano technology, Inline automatic water Drying system after pretreatment.

SMART ACOUSTICAL CEILING PANELS: Providing and fixing Smart Acoustical CEILING PANELS (HEXAGON SHAPE AS PER

APPROVED COLOUR) with square edges made of Polyester fiber substrate 9mm thick with acoustical properties and with an option

of 15 colours as per the choice of the Architect/ Person in-charge, providing a minimum sound absorption level of 0.50-0.90 NRC, to

be affixed to wall/channels using Adhesive. The material should adhere to Formaldehyde emission standards of GB18580-2001 class

E1, asbestos-free, non-toxic, non-irritant and recyclable. Material to have fire resistance as per B1 Chinese standards. The sheets to

have density of 184 kg/m3 and weight of 1.64 kg/m2. The sheets to be made available as per the design approved by Architect/

Person in charge. Cutting to be in done by supplier using laser cutting or blade cutting as per requirement.

HEXAGON: 1200x1200 WITH 1.61 SOUND ABSORPTION

TOTAL FALSE CEILING WORKS 89482.8 1109634.48

Digitally signed by SAKET

SCHEDULE OF QUANTITIES-CIVIL

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

3 WALL FINISHES WORKS

GLASS PARTITION (FIXED DOUBLE GLAZED GLASS PARTITION) : Supply & Insallation Supply & Installation of Modular Double

glazed partitioning frame of 100mm System, (100mm x 25mm) as wall starter and top section, Using (100mm x 25mm) as wall starter

3.01 MR and top section, Using (100mm x25mm) as bottom channel. Glass to Glass butt joint with I, L & T profiles. 10mm + 10mm thk clear 7.2 sq m 11531 83023.2

toughened glass. Required accessories like Gasket and Adhesive tapes as per standard partition height upto 2500mm.

FRAMED HINGED GLASS DOOR: Supply and Installation of Modular Aluminium single leaf stile door frame of make 100 mm

3.02 MR System, using (100mm x 25mm) as door frame, using for Stile door Shutter 75x45mm with 5mm + 5mm thk clear thoughened Glass. 4 sq m 33554 134216

All hardware shall be included in the item.

WOODEN DOOR FRAMES : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed

9.1 and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for

9.1.1 Second class teak wood 0.078 cu m 142949.7 11150.0766

WOODEN BATTERNS : Providing and fixing specified wood frame work consisting of battens 50x25mm fixed with rawl plug and

3.04 drilling necessary holes for rawl plug etc. including priming coat complete.

8.27.1 Kiln seasoned and chemically treated hollock wood 2.3 CUM 187277.65 430738.595

FLUSH DOOR SHUTTERS : Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type,

9.21 core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains

or cross bands and face veneers on both faces of shutters:

9.21.1 35mm thick including ISI marked Stainless Steel butt hinges with necessary screws 4.8 SQM 2392.65 11484.72

WOODEN LIPPING : Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door

shutters (over all area of door shutter to be measured).

Providing and Fixing 600-900 mm or equivelent D-type Handle Material : Stainless Steel. Finish : Satin Stainless Steel (SSS). of

approved make and model all complete as per the direction of Engineer-in-charge.

Providing and Fixing Mortise Lock Body SB/TB for door thickness 25-50 mm for of approved make and model all complete as per the

direction of Engineer-in-charge.

Providing and Fixing Double cylender Floor Spring- with Closing Force EN 3 with Maximum door weight 105 Kg. Maximum door

width 950mm.Closing speed : 130°

3.09 MR Final closing speed : 15-0°. Hold Open (standard): 90° hold open. Weight of floor spring approx : 6kg, 5,00,000 cycles Tested with 5 6 Each 9354 56124

Years Warranty against manufacturing defect. CE certified for wooden doors all complete as per the direction of Engineer-in-charge.

Providing 40x5mm flat iron hold fast 400mm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and

3.1 9.53 embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm 12 EACH 228.85 2746.2

3.11 MR Providing and Fixing top and Bottom Strap of approved make and model all complete as per the direction of Engineer-in-charge. 6 Each 1007 6042

Providing and Fixing Dead lock Back set- 50 mm with Key Hole of approved make and model all complete as per the direction of

Engineer-in-charge.

Providing and Fixing SS Cylinder One side knob and one side regular key (3 key) for wooden doors of approved make and model all

complete as per the direction of Engineer-in-charge.

Digitally signed by SAKET

SCHEDULE OF QUANTITIES-CIVIL

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

GLASS FILMS: Providing & Fixing Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-effect film to reproduce

Sand-blasting effect on glass with customised designs, thickness of 2 mil (0.05mm) without adhesive & 3mil (0.8)with adhesive having

minimum tensile strength of 3.5 pound/inch at 73 F(0.6 kg/cm at 23 C). Adhesion after 24hrs of installation should be 4 pounds/inch

(0.7 kg/cm) on Acrylic, Glass Polycarbonate: MCS warranty of 3yrs (if exposed to direct sunlight) to 15yrs (indoors) .

Providing and fixing Channelled woodwork acoustic wall panel of width of 192/132/128mm with finishing of 14.5 mm thick random

Grooved wooden acoustic panel of size 2420 mm, Groove Size 3.2mm at an interval of 21mm/28 mm c/c as per acoustic design /

Architects’ approval, the wooden acoustic panels to be backed with black acoustic fleece with NRC of 0.45 (NRC 0.8 with 50mm GW

of 48kg/m3).the edge of panel shall be Tounge and groov to be fixed with clips on aluminium profile designed specially fo the panel.

the panel will be mounted with the help of clips on Bollard Aluminium extruded Keel. The grooved acoustic panel laminated in

desired shade as per Engineer In charge / Architect’s approval.

LACQUERED GLASS: Providing and fixing of 6mm thick annealed SGG Planilaque Evolution (premium GRIHA rated lacquered glass

from Saint-Gobain) of approved color by Architect/ Client / Customer, fixed with SGG ULTRAFIX (compatible neutral core silicon /

double sided tape) on a perfectly leveled 12mm thick water proof marine plywood / MDF / Mineral fibre board which is mounted on the

3.16 MR RCC wall/any other structure. Lacquered glass must be made industrially (via curtain coating process); opaque (if viewed against a 35.225 SQM 5112 180070.2

support wall), coated with PU lacquer (50 micron thick); color consistency (measured by Minolta spectrophotometer CM5081); highly

durable (passes PERSOZ hardness test for minimum 220 oscillatios); humid resistant (conforms to BS EN 1036 1999);

environmentally friendly (no lead, no arsenic, no copper, noformaldehyde); appropriate recycled content (12% post industrial / 6% post

consumer); compressive strenght (1000 MPa) & tensile strenght (40 MPa),same as float glass;

GYPSUM BOARD PARTITION: Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including

providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both

side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor

and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor

9.105 fastener or metal screws with nylon plugs and the studs 48mm wide having one flange of 34 mm and other flange 36 mm and 0.50

3.17 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia

bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws

with nylon plugs at spacing of 450mm centre to centre, and fixing of boards to both side of frame work by 25mm long dry wall screws

on studs, floor and ceiling channels at the spacing of 300mm centre to centre. The boards are to be fixed to the frame work with joints

75mm overall thickness partition with 12.5mm thick double skin fire rated Glass Reinforced Gypsum (GRG) plaster board conforming

to IS: 2095: part 3 (Board with BIS certification marks)

ACRYLIC SOLID SURFACE CLADDING: Providing & fixing of straight Paneling for walls & Columns structures anchored in floor slab

& celling, cladded with Acrylic Solid Surface 12mm thick sheets straight fabricated on a single face, finished in matte finish, pasted

with industrial grade silicon on a robust substrate. Substrate shall be with suitable MS box sections [Appx. 15 to 20 kg/ Sqm] as per

structural requirement & duly painted with anti-rust red oxide coating and covered with 12 mm thick water proof ply as per the design

and dimensions approved. The proposal includes the cost of preparing appropriate substrate surface over the civil structure provided,

along with material cost & installation / fixing on straight walls etc. FOR ALL WALL CLADDING, TABLE TOPS ETC. COMPLETE

Providing and Fixing of Window Blinds as per the approved sample consisting of Duette double honeycomb shades with easy rise

TOP DOWN BOTTOM UP (TDBU) operating system as per following specifications:

FABRIC SPECIFICATIONS:

• Black Out original Non-woven honeycomb shades having soft fabric appearance and high energy-efficient fabric with high tear

strength constructed out of Anti static, resilent, colour fast & Sanitized Treat 100% spun bonded non-woven polyester fiber& precision

3.19 MR manufacture to form a hexagonally shaped duette pleat. The Fabric is GREENGUARD certified and can attain an NRC value of 0.75. 5 SQM 24177 120885

Certificates to be provided at the time od delivery of material at site. Pleat dimension ¾ ”Honeycomb within a Honeycomb” with 3 air

pockets for maximum energy effeciency.

• Shadings are duotone, with neutral tone facing the exterior and color facing the interior. In the TDBU mechanism the customer gets

the flexibility of having the top rail down as well as the bottom rail to the top position. Even the rails can be stacked in between as an

intermediately position where in the user has a option to stack the blind anywhere he wants. The HEADRAIL shall measure 49.68 wide

Digitally signed by SAKET

SCHEDULE OF QUANTITIES-CIVIL

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

Providing & supplying of Window Blinds as per the approved sample Duette double honeycomb shades having “honeycomb within

honeycomb” with easy rise operating system as per following specifications fabric specifications:

• Original Non-woven honeycomb shade shaving soft fabric appearance and high energy-efficient fabric with high tear strength

constructed out of Anti-static, resilent, colour fast & Sanitized Treat 100% spun bonded non-woven polyester fiber & precision

3.2 MR manufacture to form a hexagonally shaped duette pleat. The Fabric is GREENGUARD certified and can attain an NRC value of 0.75. 48.36 SQM 21299 1030019.64

Certificates to be provided at the time of delivery of material at site. Pleat dimension ¾ ”Honeycomb within a Honeycomb” with 3 air

pockets for maximum energy efficiency.

• Shadings are duotone, with neutral tone facing the exterior and color facing the interior The Head rail. Shall measure 50 wide and

35mm deep & thick 1.25mm extruded from alu. alloy& shall be powder coated to a smooth finish with a thickness of 40 microns.

Fabric shall be constructed from spun-bonded polyester fiber, precision manufactured to form a hexagonally shaped, dual pleat,

Providing & supplying of fabric venetian Window Blinds as per the approved sample, consisting of 3" vane size having head rail,

rotator rail and bottom rail made of aluminium alloy extruded profile, powder coated and provided in standard natural white color. The

rolling tube should be made up of aluminium alloy from extruded profile. The head rail dimensions should be of suitable size according

to the length of head rail and space available and finished with fabric cover matching with the louver fabric. The cassette should

conceal the working mechanism rotary-clutch. (White polycarbonate spring tempered rotary clutch which raises), lower and tilts the

3.21 MR blinds. White polycarbonate limit assemblies control vane over-rotation, located on either side of individual blinds. The room darkening 5 SQM 18277 91385

fabric of Blind should be of anti-static polyester vanes which have facings between two sheer layers (50 mm wide) to reduce glare.

Sheer layers should be of white 100% knit polyester, the colors, textures and opacities as approved. The fabric shall be made of spun-

bonded 100% polyester fibre (having green guard certification) treated with soil & dust repellent requiring minimum regular interval

cleaning. GREEN GUARD Gold certified for low-emitting products to maintain Indoor environment. Upto 80% ultraviolet protection with

vanes open and 90% with vanes closed. The shading to be operated by Easy rise mechanism with a continuous cord loop operating

PELMET: Fabricate and install pelmet made of 19 mm thick board, up to 300 mm high and in line with external glazing as per details

of Architect. Rate to include finishing exposed surfaces of the Pelmet with enamel paint of approved shade or 1mm laminate.

AAC WALL (150 MM): Providing and laying autoclaved aerated cement blocks masonry with 150mm/ 230mm/ 300mm thick AAC

blocks in super structure above

plinth level up to floor V level with RCC band at sill level and lintel level

with approved block laying polymer modified adhesive mortar all

complete as per direction of Engineer-in-Charge. (The payment of RCC

band and reinforcement shall be made for seperately).

3.24 6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. 10 Sqm 104.8 1048

13.4 12 mm cement plaster of mix :

13.4.1 1:4 (1 cement: 4 coarse sand) 10 Sqm 357.35 3573.5

3.26 13.26 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth 10 Sqm 262.7 2627

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004,

Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives

New work (Two or more coats applied @ 1.43 litre/10 sqm) over and including priming coat of exterior primer applied @ 0.90 litre/10

PLY: Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and

3.28 fixed on wooden /steel frame work, complete as per direction of Engineer-in-Charge

9.140.1 12mm thick commercial ply conforming to IS : 1328 BWR type 520 SQM 1224.65 636818

4mm THICK MDF BOARD: Providing and fixing plain lining with necessary screws/ nuts & bolts/ nails, including a coat of approved

3.29 MR primer on one face, and fixed on wooden/ steel frame work, complete as per direction of Engineer-in-Charge

4mm thick MDF Board 331.5 SQM 315 104422.5

Digitally signed by SAKET

SCHEDULE OF QUANTITIES-CIVIL

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

ALUMINIUM FRAME: Providing and fixing partition, frame work in 50x25x1.5mm Aluminium Section placed at 600mm centre to

3.30 MR centre both ways (horizontal & vertical) fastened to floor, ceiling and horizontal member. The item includes providing and fixing 50mm 272 SQM 1347 366384

thick polyester synthetic insulation as insulation of 100 GSM.

Providing and fixing 4mm thick coir veneer board, ISI marked IS: 14842, plain lining with necessary screws, priming coat on

unexposed surface etc., complete.

3.32 MR WALLPAPER: Washable Vinyl Coated Wall covering as per approved make and pattern as approved by the client 30 SQM 1500 45000

TOTAL WALL FINISHING WORKS 1911779.945 2822171.3

4 MISCELLANEOUS WORKS

MODULAR KITCHEN - UNDER COUNTER STORAGE CABINETS:

Providing & fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with openable shutters and

sufficient number of drawers made of 18 mm thk. ISI Marked comm. ply , all ply to be laminated with 0.8 mm laminate.All shelves

should be supported on approved quality SS pins and shall be adjustable for different heights as per requirements.Shutters and

4.01 MR drawers fascia shall be at least 18mm thic with laminate on both sides with 18mm wide 2mm thick PVC edge banding, All Shutters 4.05 SQM 10000 40500

finished in high gloss acrylic of approved. The cabinet boxes of floor units will be supported by 100mm height vertical adjustable legs

which will be covered with PVC skirting in brushed aluminum finish attached by hardware of skirting. The unit shall be fixed to the

floor/ wall/slab using metal screws of appropriate size and rawl plugs. Only front face area of cabinets and skirting from floor to top of

boxes shall be considered for measurement and payment. Cabinet boxes size would be varies from 400X560X710MM to

1000X560X710MM (approx.) and join together as per site requirements etc.

MODULAR KITCHEN - OVERHEAD STORAGE WALL UNITS:

Providing & fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with openable shutters and

sufficient number of drawers made of 18 mm thk. ISI Marked comm. ply. All ply to be laminated with 0.8 mm laminate.All shelves

should be supported on approved quality SS pins and shall be adjustable for different heights as per requirements.Shutters and

drawers fascia shall be at least 18mm thic with laminate on both sides with 18mm wide 2mm thick PVC edge banding, All Shutters

finished in high gloss acrylic of approved. The unit shall be fixed to the floor/ wall/slab using metal screws of appropriate size and raw

plugs. Only front face area of cabinets and skirting from floor to top of boxes shall be considered for measurement and payment.

Cabinet boxes size would be varies from 400x560x710MM to 1000x560x710MM (approx.) and join together as per site requirements

4.02A MR Providing and fixing of Innotech with metal sides and quadro channels 5 Each 3548 17740

4.02B MR Providing and fixing baskets 5 Each 4013 20065

WATERPROOFING: Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C.,

kitchen and the like consisting of:

(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended

proportions including rounding off junction of vertical and horizontal surface.

4.03 22.3 (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended 5.6 SQM 769.6 4309.76

proportion including rounding off junction of vertical and horizontal surface.

(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other

with bitumen @ 1.7 kg/sqm).

SHOP DRAWINGS: Preparation of complete set of shop drawings including finishing, MEP services, details, design calcualtions etc.

4.04 MR and for prepration of as built drawing any other details as and when desired by Engineer Incharge/ client. A qualified professsional for 1 LS 250000 250000

the purpose shall be appointed after due appproval from Engineer InCharge.

ECORESIN PANEL: Providing of Ecoresin panel of size 1220mm x 2440mm with variety of inlay between panels of specified Gauge.

The panels are made from ecoresin sheet with engineered polyester resin with a thickness of 5/ 6.3 mm (+/- 5%)with a top/ bottom

finish as sandstone finish. The product conforms to Class A impact rating in accordance as measured under ASTM standards is

GreenguardTM Indoor Air Quality certified and has a minimum of 40% post-industrial recycle content certified by a recognized 3rd

party certification group, such as Scientific Certification Systems (SCS). The design of the product is based on Varia produced with

ecoresinTM as per approved make as per specification & approval of Engineer-in-charge.

Digitally signed by SAKET

SCHEDULE OF QUANTITIES-CIVIL

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

Providing and Fixing Dyson Air purifier, Fan, all in one Vacuum filled HEPA filters air purifiers an advanced HEPA H13 filtration

4.06 MR system that captures gases and 99.95% of particles as small as 0.1 microns. For gases grid matrix turbulent flow carbon based 1 Nos. 56900 56900

chemically dosed filter. Air purifiers have powerful Air Multiplier™ technology to purify the whole room. (700-800 sqft per machine

ZINC CLADDING: Supply & Installation of ZINC Titanium (conforming to EN 988 stndards) Interlocking wall cladding panels in

VMZINC Pigmento Finish. The wall cladding system shall comprise of the following as described .ZINC 0.8 mm interlocking panels of

233 mm width and max 2000 mm length. Panels are formed with interlocking lap at panel edges and smooth, flat pan; designed to be

field assembled in sequential installation by engaging edges of each panel to edge of adjacent panel. Panels are attached to

4.07 ` supports/substrates using stainless screws located under edges of the panels The Panels Shall be Installed over the Aluminium box 17 SQ M 17360 295120

Section of 50x25x1.6 mm thick @ 600mm c/c horizontal and vertical with Screws/ Rivets of suitable size as recommended by

manufacturer .THe zinc titanium manufacturer shall have regisetered office in India and shall have supplied zinc titanium cladding to

government projects in last 5 years . Installation to be carried out by manufacturer approved installation agencies who has completed

zinc cladding projects in India.

4.08 MR Supply & Installation of ZINC Flashings in same finish and material for corners, top, botom, site detailing 6 RM 3139 18834

Wall Mounted 304 Stainless Steel Hand Dryer

4.09 MR 1650W, 7.5A ,Voltage - AC220-240V, 50Hz ,Touch Free Infra-Red Activation, Auto cutoff - 30 Sec, 24000 RPM ,Noise Level - 70 1 No 73694 73694

db(A), Air Flow Rate - 95 m/s Drying Time - 7-10s, Brushless Motor, Blowing Volume - 150 m³/h, Protection Class - IPX4 ,Weight - 12

Black Open Oval Room Dustbin

4.10 MR Material- Iron + Leather ,Color - Brown ,Size - 220*255*0.4 mm , Oval Capacity - 8 Liter , Structure - Open Top , Usage/Application - 3 No 1527 4581

Washroom Recesses Panel 3 in 1

Paper Dispenser + Hand Dryer + Waste Bin, Material- 304 Stainless Steel (Anti - Fingerprint), Door Material- 1.2mm Stainless Steel,

4.11 MR Cabinet/ Paper/ Waste Material-0.8mm Stainless Steel, Paper Dispenser Capacity-600, C-Fold or 800 Multi Fold Paper Towel, Hand 1 No 61394 61394

dryer - 800-1350W (Hot & Cold Wave)Drying time -10-12 Sec, 25000 RPM, Waste Container Capacity -21 Litres, Wall Opening

required -315mm (H) x 1665mm (H) x 126mm (D)

Automatic Trash

4.12 MR Material - Stainless Steel, Color- Silver, Operation- Sensor, Battery Operated, Total Capacity- 70 Litres, Compartment- 3, Battery- 3 x 1 No 13496 13496

D Size Duracell (Battery not included), Size- 542x330X671mm

Standing Coat Rach With Wooden Cloth Hanger

4.13 MR Material- Stainless Steel & Wood, Color- Silver Size- 470x150x1240mm, Application- Hotel Room, Living Room, Bedroom, Home 2 No 16040 32080

Office, Hospital

TOTAL MISCELLANEOUS WORKS 4309.76 1280687

Digitally signed by SAKET

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

DSR S NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

DSR S NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

2023 DSR (INR) NON-DSR (INR)

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings

17.28 complete.

17.28.2 Flexible pipe

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved

2 quality conforming to IS : 8931

18.53.1 15 mm nominal bore EACH 2 574.30 1148.60

Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast

(spun) iron pipes and making good the same with cement concrete 1:3:6 (1 cement: 3 coarse

3 sand: 6 graded stone aggregate 12.5 mm nominal size) including necessary plaster and

pointing in cement mortar 1:4 (1 cement : 4 coarse sand) :

18.76 Cutting holes upto 30x30cm in walls including making good the same.

18.76.1 With common burnt clay F.P.S. (non modular) bricks EACH 1 416.80 416.80

Making chases upto 7.5 X 7.5 cm in walls including making good and finishing with matching METRE 2 202.90 405.80

surface after housing G.I. pipe etc.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for

hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the

pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step

6 CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Internal work - Exposed on wall

18.7.2 20mm nominal outer dia pipes METRE 10 335.00 3350.00

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for

hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe

with clamps at 1.00 m spacing.

18.8 This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of

cutting chases and making good the same including testing of joints complete as per direction

7 of Engineer in Charge.

Concealed work including cutting chases and making good the walls etc.,

18.8.1 15mm nominal outer dia pipes METRE 5 497.80 2489.00

18.8.2 20mm nominal outer dia pipes METRE 5 537.60 2688.00

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS

8 standards and weighing not less than 690 gms.

18.51.1 15 mm nominal bore EACH 2 798.95 1597.90

Digitally signed by SAKET

Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipes for

soil, waste, and vent, Type-B as per IS : 13592 suitable for rubber ring joints, including all

neccessary specials and fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or

without doors), reducers, WC connectors, couplers, expansion joints / bellows, cowels,

clamps, rubber rings, clean outs etc. fixing at wall/ ceiling/ floor level supported by clamp &

hangers etc. in concealed / inside duct / under floor & basement ceiling / external work etc.

including chase cutting as required, excavation and back filling in all kind of soils, suspended

9 from floor under false ceiling or embedding the pipes laid under floors / building in 75 mm.

alround 1:2:4 cement concrete (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

MR nominal size) including cost of shuttering for proper completion of the work, breaking and

making good the walls and floors etc. after pipes have been duly laid and tested. The rubber

ring shall confirm to IS:5382.

The Pipes will be supported with threaded G I rods & U clamps with nuts, washers etc on

50x50x5 mm slotted angle. The cost will include all support arrangements. The work includes

commissioning of all pipes lines as per drawings and specifications and as directed by engg-

in-charge at site.

a 110 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 10.00 536.00 5360.00

b 75 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 2.00 416.00 832.00

Providing, fixing, jointing and testing in position ISI marked (IS:4985) UPVC pipes of min 6

Kg/ Sqcm rating with fitting for waste pipe from fixtures to floor trap including reduces,

enlarger, socket, couplers, bends, tees etc including fixing at wall/ ceiling level supported by

clamp & hangers etc. cutting holes in wall/ floors/ slabs and making good the same with

cement concrete 1:2:4 complete as required.

Providing & fixing UPVC Floor trap of self cleansing design with stainless steel grating

MR 11 complete in all respects.

Plain Floor Trap (4" Ht) with 50 / 75 outlet and with height raiser EACH 1 536.00 536.00

MR 12 Extra for providing & fixing 125 mm dia C.P. grating in place of C.I. grating over floor traps. EACH 1 726.00 726.00

Providing & fixing of SS Floor Cleanout, round or square with rubber seal and flat round EACH 1 1001.00 1001.00

cover with screws and other required fitting complete as required.

Supply, Installation, testing and commisioning of toilet waste water super quiet portable EACH 1 67430.00 67430.00

pumping station. Pump upto vertical 5 meters and horizontal 100 meter from toilet to vertical

shaft with inlet connection in portable pump side inlet of 50, 75, 110 as per requirement to

complete the work as per the directions of engineer in charge

Providing and fixing stainless steel tray below sewage pipe of size 200x200x200 mm of grade METRE 5 3629.00 18145.00

SS304 including all accessories

MR 16 Supply, Installation, Testing and Commissioning of 15 litre geyser EACH 1 12004.00 12004.00

Digitally signed by SAKET

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

DSR NO DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

DSR NO DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

S NO UNIT QUANTITY RATE

2022 DSR (INR) NON-DSR (INR)

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface / recessed medium class PVC conduit,

1.10 with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm.

FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for group controlled (looped) light point/ fan point/call bell point (without independent

switch etc.) with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface

1.55 / recessed PVC conduit, and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper

conductor single core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single

A.3 1.12 core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS Metre 2040 334.00 681360.00

PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch

1.24 box including connections but excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet Each 112 122.00 13664.00

1.24.5 6 pin 15/16 amp socket outlet Each 12 197.00 2364.00

Supplying and fixing modular blanking plate on the existing modular plate & switch box

A.5 1.26 excluding modular plate as required. Each 20 40.00 800.00

Supplying and fixing following size/module, GI box along with Modular base & cover plate on

existing modular metal boxes etc. as required.

12 Digitally signed by SAKET

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

DSR NO DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

DSR NO DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

S NO UNIT QUANTITY RATE

2022 DSR (INR) NON-DSR (INR)

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC

1.14 insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit

1.5 sq. mm + 1 X 1.5 sq. mm earth wire Metre 20 233.00 4660.00

1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Metre 300 275.00 82500.00

1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 20 334.00 6680.00

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 20 439.00 8780.00

1.14.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire Metre 50 1005.00 50250.00

1.14.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre 50 1365.00 68250.00

Supplying and making end termination with brass compression gland and aluminium lugs for

9.1 following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1

KV grade as required.

Supply of following XPLE armourned 1.1 KV grade conforming to I.S.7098/1554Aluminium

Conductor Cables :

MR Supply of following sizes of PVC sheathed PVC/XLPE insulated Aluminium conductor

armoured cable of 1.1 KV grade conforming to IS:7098 part-1 / IS:1554 part-1 respectively &

(b) 3.5 C x 95 Sqmm XLPE cable RM 10 864.00 8640.00

(c ) 3.5 C x 70 Sqmm XLPE cable RM 50 680.00 34000.00

(d) 3.5 C x 50 Sqmm XLPE cable RM 50 510.00 25500.00

(e) 3.5 C x 35 Sqmm XLPE cable RM 50 378.00 18900.00

Supply of following sizes of copper cables -PVC sheathed PVC/XLPE insulated Copper

C.3 MR conductor armoured cable of 1.1 KV grade conforming to IS:7098 part-1 / IS:1554 part-1

respectively & ISI marked.

(a) 4 C x 16 Sqmm XLPE copper cable RM 20 1446.00 28920.00

(b) 4 C x 25 Sqmm XLPE copper cable RM 20 2253.00 45060.00

(c ) 3.5 C x 35 Sqmm XLPE copper cable RM 20 2686.00 53720.00

13 Digitally signed by SAKET

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

DSR NO DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

DSR NO DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

S NO UNIT QUANTITY RATE

2022 DSR (INR) NON-DSR (INR)

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit

2.10 breaker suitable for inductive load of following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB

distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as

D.4 required. (But without MCB/ RCCB/ Isolator)

MR 12 way (4 + 36), Double door Each 3 9081.00 27243.00

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts,

2.14 residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in

the existing MCB DB complete with connections, testing and commissioning etc. as required.

E PROVISIONS FOR VOICE, DATA, SECURITY & TV SYSTEMS

Supply, installation, testing & Commissioning of 1 module 16A SWITCH SP 1 way for floor

E.2 MR Supply, installation, testing & Commissioning of 2 module 16 A Socket for floor box box. Set 2 577.00 1154.00

Supply, installation, testing & Commissioning of Specific Backbox for Carpet for Floor Box

E.3 MR along with LID and TRIM for tiles/ marble 15 to 20mm thickness material for headband and Set 2 12106.00 24212.00

single cable outlet/ glavanized steel, paint RAL 7031 for floor box .

Supply, installation, testing & Commissioning of Specific Backbox for Wooden Flooring for

E.4 MR Floor Box along with LID and TRIM for tiles/ marble 15 to 20mm thickness material for Set 2 6803.00 13606.00

headband and single cable outlet/ glavanized steel, paint RAL 7031 for floor box.

Supply, installation, testing & Commissioning of flat support plate 8 module for integration of

Mechanism for Floor Box

Supply, installation, testing & Commissioning of waved support plates for 4 module (2x2)

E.6 MR modules for Floor Box Set 2 1533.00 3066.00

14 Digitally signed by SAKET

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

DSR NO DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

DSR NO DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

S NO UNIT QUANTITY RATE

2022 DSR (INR) NON-DSR (INR)

Supplying and fixing following modular switch / socket on the existing modular plate & switch

1.24 box including connections but excluding modular plate etc. as required.

1.24.7 TV socket outlet Set 4 148.00 592.00

1.24.6 Telephone socket outlet Set 22 148.00 3256.00

Supply, Installation, Testing and Commisioning of Galavanized Iron (GI) Raceways along with

MR required suitable number of GI couplers for joining raceways and fixing GI brackets and all

accessories complete in all respect as per the directions of engineer in charge

(a) 300mmx38mm(GI) - 3 compartment Mtr 5 3603.00 18015.00

E.8 (b) 225mmx38mm(GI) - 3 compartment Mtr 10 2960.00 29600.00

Supply, Installation, Testing and Commisioning of Junction boxes for direct access to cables at

the intersection of raceways supplied completely with base and cover plates, height adjustable

junction box 65- 90 mm including all accessories ss plate of 3mm thick complete in all respect

E.9 as per the directions of engineer in charge

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE

E.10 1.19 insulated, shielded with fine tinned copper braid and protected with PVC sheath in the exisitng Meter 120 47.00 5640.00

surface/recessed steel/ PVC conduit as required

Supplying and fixing of following sizes medium class PVC conduit aong with accessories in

1.21 surface/ recess including cutting the wall and making good the same incase of recessed

conduit as required

Supplying and Installation of following size perforated of painting with powder coating M.S.

cable trays of perforation of not more than 17.5% in convinient sections, joined with connectors

E.12 suspended from the cieling with MS suspenders including bolts and nuts painting suspenders

etc as required

4.1.6 450 mm width x 50 mm depth x 2 mm thickness Metre 20 1137.00 22740.00

15 Digitally signed by SAKET

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

DSR NO DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

DSR NO DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

S NO UNIT QUANTITY RATE

2022 DSR (INR) NON-DSR (INR)

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and

F.1 5.6 providing masonry enclosure with cover plate having locking arrangement and watering pipe of SET 4 13838.00 55352.00

2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as

F.4 5.16 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. MTR 200 70.00 14000.00

G PANEL BOARDS

Designing, fabricating, transporting, unloading, storing, fixing in position, testing and

commissioning the following sheet steel cubicle type panels fabricated from 1.6mm thick

CRCA sheet, dust and vermin proof, indoor type TPN Panels with hinged lockable doors

fabricated from 2mm thick CRCA sheet, suitable for 415V, 3 phase 4 wire 50Hz AC supply with

rear access for cable alley and with segregated bus-bar chamber with tinned aluminium bus

bar and including supplying and fixing following switchgears, meters and accessories, inter-

connections, bonding to earth, powder coated painting and marking as specified. Switch

boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as

detailed in the Specifications

Colour: Gray Powder Coated, as per approved sample.

1 nos, 100 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of fault breaking

capacity 25 KA (ICS=ICU up to 433 V) complete in all respect

TPN aluminum bus bars of minimum of 200 Amps capacity with heat shrinkable colored

sleeves and I/C DMC/SMC bus bars supports at required intervals complete for cross section,

size supports & their spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

(a) 63 Amps, TPN, MCB -4 Nos.

(b) 40 Amps, TPN, MCB - 4 nos

Panel complete as above Each 1 205791.00 205791.00

16 Digitally signed by SAKET

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

DSR NO DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

DSR NO DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

S NO UNIT QUANTITY RATE

2022 DSR (INR) NON-DSR (INR)

G.2 MR UPS Panel

Designing, fabricating, transporting, unloading, storing, fixing in position, testing and

commissioning the following sheet steel cubicle type panels fabricated from 1.6mm thick

CRCA sheet, dust and vermin proof, indoor type TPN Panels with hinged lockable doors

fabricated from 2mm thick CRCA sheet, suitable for 415V, 3 phase 4 wire 50Hz AC supply with

rear access for cable alley and with segregated bus-bar chamber with tinned aluminium bus

bar and including supplying and fixing following switchgears, meters and accessories, inter-

connections, bonding to earth, powder coated painting and marking as specified. Switch

boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as

detailed in the Specifications

Colour: Gray Powder Coated, as per approved sample.

Two (2) nos, 40 Amps. 4 pole MCB , i.e four pole Moulded Case Circuit Breaker of fault

breaking capacity 25 KA (ICS=ICU up to 433 V) complete in all respect

TPN aluminum bus bars of minimum of 200 Amps capacity with heat shrinkable colored

sleeves and I/C DMC/SMC bus bars supports at required intervals complete for cross section,

size supports & their spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

1 Nos. 63A, 4P, MCB (25kA) with phase indicating lamp protected with 2A, SP, MCB's along

with E/M interlocking

(a) 40 Amps, TPN MCB - 2 nos

Panel complete as above Each 1 206870.00 206870.00

Providing and fixing MV danger notice plate of 200mm x 150mm made of mild steel, atleast 2

16 2.21 mm thick, and vitreos enamelled white on both sides and with iscription in single red colour on Nos. 4 269.00 1076.00

front side as required

MR Supply, Installation, Testing and Commissiong of 10 KVA True Online Modular Type Double

Conversion UPS 3Phase Input - 3Phase Output in Parallel Redundant N+1 Configuration

IGBT Based Rectifier and IGBT Based Inverter Batteries:12 V, SMF Amararaja/Exide with

minimum VAH capacity of 15600 suitable for 30 minutes backup with each ups Along with

Accessories Rack, Interlinks, SFU, Parallel Kit, DC Cable Upto 5 Meters complete in all

respect as per the directions of the engineer in charge. UPS should have availability of Input

/Output isolator, Inbuilt manual bypass along with phase sequence corrector. UPS Efficiency

shall not be less than 94% from 25% to 100% Load

Total of Electrical items 1389919.00 1849452.00

17 Digitally signed by SAKET

SCHEDULE OF QUANTITIES - HVAC WORKS

DSR (E & M- Non DSR

S NO DESCRIPTION UNIT QUANTITY RATE DSR AMOUNT

2022)/ MR AMOUNT

VAV BOX (WITH INTEGRAL SOUND ATTENUATOR)

Supply and Installation of pressure independent rectangular VAV unit with integral sound attenuator

made of 22G GI sheet casing length 900mm consisting of 25mm thick 48kg/m3 density fiber glass

wool covered with tissue paper ,elliptical volume control damper , calibrated differential pressure

MR sensor (DPT sensors) at inlet complete with digital Thermostat.(All VAV shall be factory calibrated).

DUCT PRESSURE SENSORS

Supply, Installation and Testing of pressure sensors to be installed in supply air ducts. Quoted

2.0 MR price shall be inclusive of necessary conduting, copper control cabling from the sensors to the Nos. 2 17500.00 35000.00

respective VFDs as per "Approved Shop Drawings".

Supply, Installation, Testing & Commissioning of Silent type circular /rectangular inline fans for exhaust

air complete with sheet metal casing, 25mm thick acoustic insulation, direct driven centrifugal fan,

motor with proper protection and inspection door. Fan shall be suitable for operation on 220+6 %

volts, 50 Hz,1 phase AC power supply. Flanges to be provided on both sides to facilitate duct

connections. Fan shall be installed as shown in the drawings and will be of following characteristics:

MR All single phase inline fans shall be provided with factory fitted speed regulators. All Fans Should be

complete with Plug Top & necessary power cable.

Fans shall have low noise level in rage of 35-40dBA @3m and shall be suitable for indoor installations.

a 200 CFM for pantry Nos. 1 6449.00 6449.00

4.0 Tube Axial Fan

Supply Installation, testing and commissioning of supply air Tube Axial flow fan of following capacity

with GSS casing and aluminium alloy impellers with high efficiency aero-foil sections, blades, the

MR impeller directly driven by TEFC induction motor suitable for 3 Phase 50 Hz 415 V ± 10 %, complete as

required. This cost shall include the cost for suitable panel, DOL starter, breakers etc compete in all

respect as per the directions of engineer in charge.

2000 cfm at 15 mm static presuure for fresh air/exhaust air With Class "H" insulation. NOS 1 60000.00 60000.00

Digitally signed by SAKET

SCHEDULE OF QUANTITIES - HVAC WORKS

DSR (E & M- Non DSR

S NO DESCRIPTION UNIT QUANTITY RATE DSR AMOUNT

2022)/ MR AMOUNT

Supplying, Fixing, testing and commissioning of fire dampers in supply air duct/main branch and return

air path as and where required of required sizes i/c control wiring,the damper shall be motorized and

spring return so as to close the damper in the event of power failure automatically and open the same

5.0 16.20 in case of power being restored. The spring return action shall be inbuilt mechanism and not externally

mounted. The damper shall also be closed in the event of fire signal complete as required and as per

specifications.

(Fire damper shall ve suitable for 120 minutes fore rating as per NBC norms)

GI Gravity Louver

6.0 MR Supply, installation, testing and commissioning of GI Gravity Louver complete with neoperene rubber

gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

7.0 VOLUME CONTROL DAMPER

MR Supply, Installation and Testing of GI box type volume control dampers as per the specifications and

a shop drawings. SQM 1 5900.00 5900.00

- For Rectangular Ducts

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/

round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers,

supports etc. as per approved drawings and specifications of following sheet thickness complete as

a 16.12.1.1 Thickness 0.63 mm sheet SQM 40 1080.00 43200.00

b 16.12.1.2 Thickness 0.80 mm sheet SQM 40 1263.00 50520.00

c 16.12.1.3 Thickness 1.00 mm sheet SQM 20 1381.00 27620.00

d 16.12.1.4 Thickness 1.25 mm sheet SQM 10 1836.00 18360.00

Diffusers & Grills

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume

control dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without

volume control dampers complete as required

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with

aluminium volume control dampers with anti smudge ring & removable core.

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without

volume control dampers with anti smudge ring & removable core.

Supply, Installation, Testing of 125mm deep antivibration flexible joints at the outlet of air handling

13.0 MR units/ductable split units//inline fans. Flexible connections shall be constructed using imported fire RM 2 1440.00 2880.00

retardant fabric with extruded aluminium frame/flange on both sides of approved make.

Digitally signed by SAKET

SCHEDULE OF QUANTITIES - HVAC WORKS

DSR (E & M- Non DSR

S NO DESCRIPTION UNIT QUANTITY RATE DSR AMOUNT

2022)/ MR AMOUNT

Supply, Installation, Testing and Balancing of linear slot diffusers as per the approved shop drawings

and specifications. Each slot shall be 25mm wide. The diffuser face shall be a one piece extrusion so

there are no visible joints. Slot diffusers shall be complete with end caps either as end plates or end

angles or integral part, air control blades etc. Slot diffuser have a variable neck length and the diffuser

14.0 MR face could be optionally be fitted to the plenum box on site. Diffuser shall have provision to access

collar dampers for air balancing.

All Return air diffusers in false ceiling to be properly supported from real slab using chains or gripple

3 slot/2slot, powder coated extruded aluminium diffusers of approved colour & shade. SQM 2 12500.00 25000.00

Supply, Installation and Testing of Bird Screens with GI wire mesh to be installed at the suction of

15.0 MR fresh air/discharge of Exhaust air as per the specifications and shop drawings. Sample of bird screen SQM 1 5436.00 5436.00

to be got approved from consultants and Clients prior to procurement.

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile

rubber (Class "O") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The

16.0 joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation

complete as per specifications and as required.

Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass

wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre

17.0 16.21 to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet SQM 10 708.00 7080.00

fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc.

complete as required and as per specifications

Supply, Installation, Testing and Commissioning of Air Purification systems in the specified areas

where AHU/VRF/FCU/Cassette/Hi-Wall/Ductable units etc are installed, so as to improve indoor air

quality by using, Self-cleaning Needlepoint Ionizer made of Carbon brush emitters. The Needlepoint

brushes shall be designed to properly release equal amount of positive and negative ions in the supply

air,>400Million ions/cc without any obstruction. The units to be suitable for capacities up to 6000 CFM,

18.0 with universal voltage input 24V to 240V AC/DC, ionizer indicator LED, set of dry contacts which will

indicate ionizer functionality. The unit shall have capability to be switched on 24/7 and shall have

weathertight conduit of minimum 6ft length.System should kill microorganisms and pathogens and

backed with Independent lab test reports on the real virus and not surrogate. The system also should

reduce odors, TVOC’s and reduce particle/particulate matter/PM2.5/PM10. The products should be

UL 2998 listed with zero Ozone Emission.

Smart Indoor Air quality monitor to measure Air quality parameters including AQI, PM1, PM2.5, PM10,

CO2, Humidity and Temperature. In addition to the mentioned sensors of the base device, you can

customize it to measure more parameters by adding extra sensors. This monitor should be a 3-tier

architecture including sensor Hardware, secure cloud infrastructure, monitoring apps including

dashboard, android/IOS apps, where ever requires. Dashboard should be customisable and IOT

(Internet of things) enabled with view and management for all of your locations on one dashboard so

that you can easily identify and address any air quality issues. Sensors should be soft calibratable. The

System should be capable of providing periodic Preventive maintenance for automated after sales

support service in form of notification/ alerts and user interaction through dashboard application.

Air Quality Monitor Nos 1 7580.00 7580.00

Digitally signed by SAKET

SCHEDULE OF QUANTITIES - HVAC WORKS

DSR (E & M- Non DSR

S NO DESCRIPTION UNIT QUANTITY RATE DSR AMOUNT

2022)/ MR AMOUNT

Supply, installation testing and commissioning of Router / Supervisory Controller which will manage

the VAV information and communicates on BACnet®/ LONWORKS® protocol to monitor and Control

the VAVs from BMS software on PC in accordance with the approved shop drawings and technical

specifications. Connecting the final daisy loop from all VAV to Supervisory Controller shall be part of

the scope. The communication between Supervisory controller and BMS software in PC should be on

IP. Cost include powder coated Panel for Supervisory Controller of required size with 24 Volts

provision which includes power cable, plug, transformer and with all necessary accessories for

mounting on wall in accordance with the approved shop drawings and technical specifications.

Supply, Laying, Termination of ISI Certified 2 Core 1.0 sq.mm ATSC, FRLS,PVC insulated,

Unarmored, Tinned Copper, twisted, shielded, PE insulated, VAV Communication Cable with proper

ferrules, lugs and other necessary accessories. The spec shall meet the system manufacturer

specifications.

Supply, Laying, Termination of ISI Certified 4 Core 1.0 sq.mm ATSC, FRLS ,PVC insulated,

Unarmored, Tinned Copper, twisted, shielded, PE insulated, VAV Communication Cable with proper

ferrules, lugs and other necessary accessories. The spec shall meet the system manufacturer

specifications.

Supply & Laying of ISI Certified 1" dia PVC Conduit with bends, collar, saddles, saddle base and other

accessories for Signal Cable / DDC Communication Cable

TOTAL HVAC WORKS 394726.0 611893.0

Digitally signed by SAKET

SCHEDULE OF QUANTITIES: IT

TOTAL TOTAL AMOUNT

TOTAL TOTAL AMOUNT

S No Description UNIT QUANTITY RATE

A. UTP Components for Data DSR (INR) NON-DSR (INR)

Supply, Fixing & Laying of CAT 6A UTP cable 23 AWG solid copper

1 conductors for Connectivity of Hub room to End Point.High Speed Gigabit Mtr 2600 72.00 1,87,200.00

Ethernet U/UTP, 250 MHz, Class E, 23 AWG, Unshielded LSZH Cable, C6

Supply, Installation, Testing and Comissioning of I/O port for CAT6A cable

termination at Work Station end. Keystone Unshielded Outlet, 180DG C6 Blue

Supply , Installtion , Testing and Comissioning of CAT6A patch cord 2 Mtr (7

3 feet) for information outlet (I/O) to end user device connectivity.High Speed Nos. 52 350.00 18,200.00

Gigabit 24AWG U/UTP Patch Cord, LSZH, C6

Supply , Installtion , Testing and Comissioning of CAT6A patch cord 1 Mtr (3

4 feet) for information outlet (I/O) to Rack End Redantant device Nos. 52 279.00 14,508.00

connectivity.High Speed Gigabit 24AWG U/UTP Patch Cord, LSZH, C6

Supply, Installation, Testing and Comissioning of 24 port Loaded Jack Panel

for CAT6A cable termination at rack end. Data Active

Supply, Fixing & Laying of CAT 6 UTP cable 23 AWG solid copper conductors

6 for Connectivity of Hub room to End Point.High Speed Gigabit Ethernet Mtr 660 38.00 25,080.00

U/UTP, 250 MHz, Class E, 23 AWG, Unshielded LSZH Cable, C6

Supply, Installation, Testing and Comissioning of I/O port for CAT6 cable

termination at Work Station end. Keystone Unshielded Outlet, 180DG C6

Supply, Installation, Testing and Comissioning of 24 port Loaded Staggred

Jack Panel for CAT6 cable termination at rack end. Voice Active

Supply, Installation, Testing and Comissioning of CAT6 patch cord 1 Mtr (3

9 feet) for information outlet (I/O) to end user device connectivity. (Rack end), Nos. 22 235.00 5,170.00

High Speed Gigabit 26AWG Patch Cord, LSZH, C6

Supply, Installation, Testing and Comissioning of CAT6 patch cord 2 Mtr (7

10 feet) for information outlet (I/O) to end user device connectivity. High Speed Nos. 22 275.00 6,050.00

Gigabit 24AWG U/UTP Patch Cord, LSZH, C6

Supply, Installation, Testing and Comissioning of 2 Port British Style

Shuttered Face Plate white for I/O fixing at user side

Supply, Installation, Testing and Commissioning of 50 pair MDF box complete

with Krone Modules

13 Supply, Installation, Testing and Comissioning of 50 pair riser cable Nos. 1 600.00 600.00

14 Supply, Installation, Testing and Commissioning of 6 core OM3 Multimode Mtr 50 250.00 12,500.00

22 Digitally signed by SAKET

SCHEDULE OF QUANTITIES: IT

TOTAL TOTAL AMOUNT

TOTAL TOTAL AMOUNT

S No Description UNIT QUANTITY RATE

C. Backbone Component

Supply, Installation, Testing and Comissioning of OS2 G.652.D 1-fibre,

buffered, LC Duplex, LC to pigtail, 1m.

Supply, Installation, Testing and Comissioning off Rack mount fibre tray

16 supporting 6 way configuration in LC Duplex. Panel should be loaded with 6 Nos. 8 82,500.00 6,60,000.00

port LC duplex adaptor panel

Supply, Installation, Testing and Comissioning off Rack mount fibre tray

17 supporting 24 way configuration in LC Duplex. Panel should be loaded with 24 Nos. 1 58,917.00 58,917.00

port LC duplex adaptor panel

SITC of 42U 800x1000 Server Rack with perforation, Glass Door, Cable

18 managemenet, 6/16A power strips- 2 nos, Castors, 4 fan for cooling, Rack Nos. 1 80,000.00 80,000.00

should have shelves - 4 nos

D. Network Rack and Other Accessories

SITC of router with Aggregate Throughput (Default) 500mbps, Aggregate

Throughput (Performance License) 1gbps, Total onboard WAN or LAN

10/100/1000 ports 4nos, RJ-45-based ports 4nos, SFP-based ports 4nos, NIM

slots 3nos, Default memory DDR3 ECC DRAM (data plane) 2gb, Maximum

memory DDR3 ECC DRAM (control/servic es plane) 16gb, Default flash

memory 8gb, USB console port -type B mini (up to 115.2 kbps) 1nos

SITC of firewall with 22 x GE RJ45 ports (including 2 x WAN ports, 1 x DMZ

port, 1 x Mgmt port, 2 x HA ports, 16 x switch ports with 4 SFP port shared

media), 4 SFP ports, 2x 10G SFP+ FortiLinks, dual power supplies

redundancy., 3 years Enterprise Protection

SITC of L3 Switch with 24X 10/100/1000 Base-T ports and 4x 10G/1G fixed

uplinks interface. Distribution Switch shpuld have minimum 16GB Flash

memory, Advanced switching capabilities BGP, EIGRP, HSRP, IS-IS, BSR,

MSDP, PIM SM, PIM SSM, BIDIR-PIM, IP SLA, OSPF. VRF, Software-

Defined Access (VXLAN, LISP, SGT), MPLS, mVPN 3 years warranty support

for Access Switches.

SITC of Access Switch with minimum of 48x 10/100/1000 Base-T ports, 4x 10

Gig SFP+ ports for uplink ports(supporting Single mode & Multi mode 1G/10G

(LX, LR, SX & SR modules). Should have Non-blocking switch fabric, IPv6

Ready with RPS 3 years warranty support for Access Switches.

SITC of 24 port POE Access Switch with minimum of 24X 10/100/1000 Base-

T POE ports, 4x 10 Gig SFP+ ports populated for uplink ports (supporting

23 Single mode & Multi mode 1G/10G (LX, LR, SX & SR modules). Should have Nos. 3 4,16,385.00 12,49,155.00

Non-blocking switch fabric, IPv6 Ready with RPS 3 years warranty support for

Access Switches.

SITC of Hardware controller managed 2*2:2 Indoor Wi-Fi 6 (802.11ax) Access

23 Digitally signed by SAKET

SCHEDULE OF QUANTITIES: IT

TOTAL TOTAL AMOUNT

TOTAL TOTAL AMOUNT

S No Description UNIT QUANTITY RATE

25 SITC of 10 Gig SR transceivers/equivalent LC connector MM Nos. 10 44,841.00 4,48,410.00

26 SITC of MM OM3 Fibre Patch Cords Nos. 5 6,406.00 32,030.00

24 Digitally signed by SAKET

SCHEDULE OF QUANTITIES: CCTV

S No Item Description UoM Qty Rate DSR Amount NDSR Amount

SITC of 2MP, 1/2.8” CMOS image sensor, low illuminance, high image definition, Outputs 2MP

(1920 × 1080) @ 25/30 fps Built-in IR LED, max IR distance: 30 m, Intelligent detection: Intrusion,

tripwire,Abnormality detection: Motion detection, video tampering, no SD card, Supports max. 256

GB Micro SD card, IP67, IK10 protection etc all complete.

SITC of 8 channel Smart H.265+/H.265/Smart H.264+/H.264/MJPEG decoding format. · Max.

decoding capability: 32 × 1080p@30 fps or 32 × 2MP@30 fps. · Max. 384 Mbps

incoming/recording/outgoing bandwidth. · Support AcuPick with Max. 16-Channel. · Support N+M

cluster. · AI by recorder: 2-channel face detection and recognition, 4-channel perimeter protection,

and 8-channel SMD Plus. · AI by camera: Face detection and recognition, perimeter protection,

SMD Plus, metadata, ANPR, stereo analysis, heat map, and people counting etc all complete.

3 SITC of Hard Disk 16TB required for the above NVR etc all complete. No's 1 47,855.00 47,855.00

SITC of CORE I3-12 TH GEN, 8 GB RAM. 512 GB SSD, NO DVD, WIRED KEYNOSRD N

MOUSE, WITH WIN 10 PRO etc all complete.

SITC of 55" Professional Ultra HD Display Panel, 4K UHD (3840x2160) Resolution, Brightness 400

Nits, Dynamic Contrast Ratio: 500000:1, Viewing angle (horizontal / vertical): 178 / 178 degree,

5 Display Colours: 1.07 Billion, Panel technology: IPS / Direct LED, Contrast ratio (typical) 1200:1, No's 1 99,730.00 99,730.00

Connectivity: Video Input: 2 HDMI 2.0, 2 USB 2.0, DVI-I, Audio In, Audio Out, COntrol: RS232,

Ethernet, 2x10W Built-in speakers,BIS Certified etc all complete.

SITC of Layer 2 12-Port Unmanaged Gigabit Switch with 8-Port PoE, Intelligent PoE, Red Port

6 Supports BT 90W, All-giga Ports, Smooth Transmission, Wide Working Temperature: –10°C to No's 1 24,910.00 24,910.00

55°C (14°F to 131°F), Plug and Play etc all complete.

SITC of Network Wiring for Cameras/devices with CAT 6 cable from NVR in existing exposed /

7 recessed 25 mm dia Conduit including termination and providing/fixing 1.2 mm thick GI box with Box 1 7,990.00 7,990.00

grid plates with earthing complete in all respect.

6U 400 Deep, Wall Mount, Front Transparent Toughened Glass Door with Lock, Network Rack

including 1 Nos Wire Managers, 1 No. Power Distribution Board

9 8 Port Patch Panel with 24 Nos CAT6 Information Outlets in existing Network Rack No's 3 6,600.00 19,800.00

10 CAT6 Patch Chord in existing Network Rack No's 6 5,800.00 34,800.00

11 CAT6 IO / Connector at camera location No's 6 5,000.00 30,000.00

IP CCTV and Suvilliance Solution 4,43,900.00

Digitally signed by SAKET

SCHEDULE OF QUANTITIES - LIGHTING WORKS

S NO DSR/MR Description Image Unit QTY Rate DSR AMOUNT NON DSR AMOUNT

Supply, Installation, Testing and Commisioning of Pendant customised

luminaire with HE-High Efficiency LED (Light Emitting Diode) system power: 12

W/Mtr, the luminous flux of luminaire 960 lm, color temperature of 4000 K, CRI

> 90, SDCM<3, THD<10%, 230 V constant current driver, 70% of luminous flux

after 50,000 operating hours, direct light emission, luminaire profile in

1 MR aluminium, black powder-coated, opal diffuser for uniform illumination, Mtr 12 30000.00 360000.00

Electronic control gear.

Protection class I, IP20 L = 1000 mm, B = 55 mm, H = 75 mm, PL max = 1500

mm (one customised suspended Ring type fixture of 3800mm Diameter

Supply, Installation, Testing and Commissioing of Recessed downlightwith

HPE (High-Performance Efficiency) with LED (Light Emitting Diode), system

power: 12 W, Luminous flux of luminaire 1320 lm, 110 LM/W system efficacy,

Colour temperature of 4000 K, Neutral white, CRI > 80, 230V constant current

driver, 70% of luminous flux after 50,000 operating hours; energy-efficient

LEDs, direct light emission, housing in die-cast aluminium, Polyester powder

white coloured coat applied over a 5-stage pre-treatment trim, prismatic

diffuser for homogenous light distribution, ZHLS (ZERO HALOGEN LOW

SMOKE) wiring, Electronic control gear,

Protection class II, IP 40, Ø = 175 mm, DA(Ø) = 160 mm, H = 59 mm

Supply, Installation, Testing and Commissioing of Pendant/Recessed luminaire

with LED (Light Emitting Diode), system power 28 W, luminous flux of

luminaire 3080 lm, 110 LM/W system efficacy, direct light emission CRI>80,

colour temperature of 4000K, Neutral white, 230V constant current driver, 70%

of luminous flux after 50,000 operating hours, energy efficient LEDs, luminaire

profile in aluminium, Plastic moulded end caps, Polyester powder Aluminium

white coloured coat applied over a 5- stage pre-treatment, high efficiency glare-

free snap fit micro-prismatic diffuser for homogeneous light distribution, ZHLS

(Zero Halogen Low Smoke) internal wiring, integral Electronic control gear,

adjustable suspender,

Protection class I, IP 20, L = 1199 mm, B = 75 mm, H = 90 mm, PL max =

Supply, Installation, Testing and Commisioning of Recessed downlight with

LED (Light Emitting Diode) system power: 5W, Luminous flux of luminaire 400

lm, Colour temperature of 4000 K, Warm white, CRI > 80, 230V constant

current driver, 70% of luminous flux after 50,000 operating hours; energy-

efficient LED, direct light emission, housing in die-cast aluminium, Polyester

4 powder white coloured coat applied over a 5-stage pre-treatment ceiling trim, no 4 1200.00 4800.00

with reflector, beam angle of 24°, Electronic control gear,

Protection class II, IP 20,

26 Digitally signed by SAKET

SCHEDULE OF QUANTITIES - LIGHTING WORKS

S NO DSR/MR Description Image Unit QTY Rate DSR AMOUNT NON DSR AMOUNT

Supply, Installation, Testing and Commisioning of Recessed with trim luminaire

with Pinspot light with LED(Light Emitting Diode) system power: 8W, luminous

flux of luminaire 640lm, colour temperature of 4000K, CRI > 90, SDCM<3,

THD<10%, 230V constant current driver, 70% of luminous flux after 50,000

5 MR operating hours, direct light emission, aluminium housing with trim, polyester no 36 2400.00 86400.00

Black powder coat applied over a 5 stage pre-treatment on trim, with lens and

a beam angle of 36° and external Electronic control gear

Protection class II, IP20

STRETCHED FABRIC CEILING: Supply & installationof fabric false ceiling /

wall formed out with TRANSLUCENT Printed fabric coverings made out of

polyester knitted fabric coated with Polyurethane (PU). The TRANSLUCENT

Printed fabric width of 2m, 3m, 4.1m &5.1m with weight of 200gm/m2,

thickness of 0, 3 mm. The appearance of fabric is matt, smooth and uniform

with blanq color and light transmission of 50%. The tear strength of fabric

should be accordance to CH: 4,5daN; TR: 6,5 daN. The fire rating should be

accordance to B-S1, d0. The fabric should be humidity resistant and free of

carcinogenic substances(CMR) or volatile organic Compounds (VOC’s). At

6 MR labeling in accordance with the French decree no. 2011- 321, Oeko-Tex Sq Meter 5.06 12798.00 64757.88

standard100 certified. Fabric should be installed with approved manufacturer

guidelines. It comes with 10- year manufacturer guarantee. The installation of

TRANSLUCENT Printed fabric should be dry installation & done at room

temperature using CLIPSO PVC, ABS Grippers. Clipso ceiling base to be

made of MS or Wooden frame finishing to a flush finish of tapered and square

edges in desired design as per architect specification.Supply of LED Lights

behind the Fabric Wall/ False ceiling in modules/ PCB with recommended

wattage as per manufacturer's standards to give an effect of ambient lighting.

LED make MLS/ Bridgelux / Osram- SMD 2835, LED spacing / Pitch should be

atleast 73 -80mm with beam angle of 170 degree, Colour temperature shoud

27 Digitally signed by SAKET

SCHEDULE OF QUANTITIES - FIRE ALARM

DSR NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT

DSR NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT

2022 DSR (INR) NON-DSR (INR)

SITC of UL268 6th and 7th edition compliance and FM approved Intelligent Addressable multi-

criteria detector (optical and thermal sensors) complete with standard base, facility to mount in

different comprehensive environment, Tri-color detector-status LED with 360 ° view,

microprocessor circuitry with error check; detector self-diagnostics and supervision

programs,Rate-of-Rise Detection: 15°F / min. (8.3°C / min.) - Fixed: 135°F (57°C) , Field

1 MR programmable as rate-of-rise or fixed temperature, Polarity insensitive, Superior EMI and RFI No 12 3175.00 38100.00

immunity, RoHS compliant. Detector shall have in-built isolator for better reliability, circuit

integrity and advanced fault finding. Manufacturers not having in-built Isolator feature in

detector shall consider Isolator base in place of standard base OR separate Isolator before

and after every detector to comply the same without any extra cost. It shall be

includesurface/recessed MS Box complete with all connections etc as required.

SITC of UL Listed and FM approved Intelligent Addressable Rate of Rise and Fixed

temperature detector complete with standard base, Seven (7) field-selectable settings in a

temperature range of 135°F – 174°F (57.2°C – 78.9°C) , a low-temperature warning of 40°F

(4.4°C), facility to mount in different comprehensive environment, Tri-color detector-status LED

with 360 ° view, microprocessor circuitry with error check; detector self-diagnostics and

2 MR supervision programs, Field programmable as rate-of-rise or fixed temperature, Polarity No 1 3028.00 3028.00

insensitive, Superior EMI and RFI immunity, RoHS compliant. Detector shall have in-built

isolator for better reliability, circuit integrity and advanced fault finding. Manufacturers not

having in-built Isolator feature in detector shall consider Isolator base in place of standard

base OR separate Isolator before and after every detector to comply the same without any

SITC of UL Listed Sounder cum Strobe rated at 75 dBA @ 3m for Audible annunciation and

75cd flashintg at 1 Hz for visual indication.

SITC of UL listed and FM approved Intelligent addressable Class X type (Style 7), Control

Module with built in dual isolator, polarity insensitive, Tri color LED for status (Green for

Normal,Yellow for Faulty and RED for activation), Operating Temp and RH: 0-49degC and

4 MR <=95%. Module shall have in-built isolator for better reliability, circuit integrity and advanced No 1 3753.00 3753.00

fault finding. Manufacturers not having in-built Isolator feature shall provide separate

Isolator before and after every Module to comply the same without any extra cost. (For

AHU & Staircase Pressurization Fans, Hooters / Sounders / Strobes etc.)

SITC of UL listed and FM approved Intelligent addressable Class X type (Style 7), Monitor

Module with built in dual isolator, polarity insensitive, Tri color LED for status (Green for

Normal,Yellow for Faulty and RED for activation), Operating Temp and RH: 0-49degC and

5 MR <=95%. Module shall have in-built isolator for better reliability, circuit integrity and advanced No 1 2950.00 2950.00

fault finding. Manufacturers not having in-built Isolator feature shall provide separate

Isolator before and after every Module to comply the same without any extra cost. (For

Flow Switch Monitoring/ Gass suppresion Integration etc.)

SITC of UL268 6th and 7th edition compliance and FM approved Intelligent Addressable

Duct detector with 10ft sampling pipe (optical and thermal sensors) complete with standard

base, facility to mount in different comprehensive environment, Tri-color detector-status LED

with 360 ° view, microprocessor circuitry with error check; detector self-diagnostics and

supervision programs,Rate-of-Rise Detection: 15°F / min. (8.3°C / min.) - Fixed: 135°F (57°C) ,

Field programmable as rate-of-rise or fixed temperature, Polarity insensitive, Superior EMI and

RFI immunity, RoHS compliant. Detector shall have in-built isolator for better reliability,

circuit integrity and advanced fault finding. Manufacturers not having in-built Isolator

feature in detector shall consider Isolator base in place of standard base OR separate

Isolator before and after every detector to comply the same without any28 extra cost.

Digitally signed by SAKET

SCHEDULE OF QUANTITIES - FIRE ALARM

DSR NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT

DSR NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT

2022 DSR (INR) NON-DSR (INR)

SITC of UL Listed Sounder cum Strobe rated at 75 dBA @ 3m for Audible annunciation and

75cd flashintg at 1 Hz for visual indication.

SITC of UL listed and FM approved Intelligent addressable Class X type (Style 7), Manual

Pull Station Single Action, Shock and Vibration Resistant, with built in dual isolator, polarity

insensitive, Tri color LED for status (Green for Normal,Yellow for Faulty and RED for

8 MR activation), T-45 Key Reset lockset for easy maintenance, Operating Temp and RH: 0-49degC No 1 4301.00 4301.00

and <=95%. MCP shall have in-built isolator for better reliability, circuit integrity and advanced

fault finding. Manufacturers not having in-built Isolator feature shall provide separate

Isolator before and after every MCP to comply the same without any extra cost.

Supplying, installation, testing & commissioning of 8 zone, voice alarm controller with USB,

MP3 player (including 8 zone button paging station) with seamless integration facility with main

9 MR fire alarm panel for voice evacuation. 3. The controller shall comply standards of BS EN54-32 No 1 229838.00 229838.00

& EN608409, Controller shall have AC 230V and DC24V battery input. Auto switch into the

battery backup when AC fails.

Supplying & laying of 2x1.5 sqmm fire alarm FS armoured cable, 600/1000V rated with

10 MR annealed copper conductor having XLPE insulation, steel wire armouring & FS outer sheath Mtr. 120 235.00 28200.00

complete as required

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the

existing surface / recessed steel conduit of following pairs, cores and size including

connections and interconnections etc. as required.

Supplying and Laying of 2x1.5sqmm FS unarmourd cable Mtr 90 158.00 14220.00

Supplying & Fixing of battery operated illiminated "EXIT" signage, with 2hrs power Battery

backup complete as required.

Supplying, Installing, Testing & Commissioning of LED technology, High efficiency,

Emergency light s with Function Use as an emergency luminaire Testing system Stand

Alone, Housing Polycarbonate, Glow wire test : 850°C, RAL9003, Type of mounting Surface:

Recessed base for ceiling, double sided cone diffuser, plexi plate diffuser, Degree of protection

13 MR IP65, Operation Mode Non Maintained or Maintained & Non Maintained mode selectable, NOS 1 7637.00 7637.00

Connection voltage 230V -/+ 5% [220V-240V] 50-60Hz, Permissible ambient: temperature

+5°C to +40°C, Battery: Ni-Cd, Duration 3 hours, Viewing distance 20m or 30m, Insulation

class II, 20 mtrs. viewing distance, Dimensions in mm: 270x119x49; for 30m viewing distance

version: 371x170x62

SITC of Remote Paging Microphone should be fully digital connected via CAT6 Cable with

Controller. The Microphone should have capability to make announcement in 96 Zones and

have all call facility. The Microphone shall have ability to control music and should be able to

route the music in zones. Microphone should have maximum zones capacity up to 120 Zones.

The Microphone should have LED indication for the different faults, the unit shall be able to

indicate AC, DC, Fault, Mic and Test status through LED.. The Unit shall have 2 RJ45 ports for

Microphone so that the other microphone shall be able to link with the unit. The Microphone

shall have ability to Communication limit up to 600 Meters

Supply, Installation, Testing and Commisioning of Loop Card capacity of 159 detectors For

BMS Fire integration compatible with existing system

Supply, Installation, Testing and Commisioning of Interface Card for BMS fire integration

compatible with exisiting system

Supply, Installation, Testing and Commisioning of repeater panel having 160 character liquid

crystal with backlit control compatible with existing system

Digitally signed by SAKET

SCHEDULE OF QUANTITIES - FIRE ALARM

DSR NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT

DSR NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT

2022 DSR (INR) NON-DSR (INR)

SITC of UL864 10th Edition UL Listed and FM approved Analog Addressable 2 Loop Fire

Alarm control panel. Panel shall be running on full digital protocol with 32 bit Microprocessor .

The Panel shall be complete with 6" color touch screen LCD Display. Fire alarm panel should

have minimum capacity of 2500 detectors and devices in any combination and capable of

making upto 50 loops in single panel using additional Loop cards. Each addressable loop

shall be capable of taking 250 addresses per loop configuring either as all detectors or

modules or any mix of both. The panel shall have the Fire Fighter Touch Screen Graphical

Display panel to inform & guide Fire Fighters for carrying out Fire Fighting operations. The

display shall have Hazmat icons indicating the presence of any explosive gas, liquids,

18 MR poison,fumes etc. If this feature is not available in fire alarm panel then additional fire fighter Nos 1 466667.00 466667.00

touch panel along with necessary hardware and software should be provided by the

manufacturers for fire fighters to guide them during emergency without any extra cost. To

expedite system troubleshooting, the system cards shall have ground fault detection and

diagnostic LEDs by card. In the display,simple building floor plan can be loaded in bitmap or

jpeg format, On the map, the user will see an icon indicating the location of the event in the

building in addition to a 'You-Are-Here' symbol to tell the responding person exactly where they

are in the building in relation to the event. The system shall be polarity insensitive. The panel

shall support degrade mode operation and shall have battery backup of 24 hrs in normal

condition and 30 minutes in Alarm condition.

TOTAL FIRE ALARM WORKS 0.00 1222969.00

Digitally signed by SAKET

SCHEDULE OF QUANTITIES: IPABX

S No Item Description UoM Qty Rate DSR Amount NDSR Amount

SITC of High-resolution 2.7” graphical TFT display 32 self-labelling function keys (8 physical keys)

for Speed dialing,12 SIP identities / accounts, Dual switched, gigabit ethernet ports, PoE (Power on

Ethernet), And other standard features

SITC of High-resolution backlit display, Dual switched ethernet ports, 2 SIP identities / accounts, 5

2 fixed function keys, PoE (Power on Ethernet), And other standard features No's 20 11,810.00 2,36,200.00

Digitally signed by SAKET

SCHEDULE OF QUANTITIES: ACCESS CONTROL

S No Item Description UoM Qty Rate DSR Amount NDSR Amount

SITC of Integrated Visitor Managment System Desk license at

Reception desk at each floor etc all complete

SITC of Biometric Machine: User identification in 1 second Minimum

500 Users and Expandanbe up to 10,000 users (30,000 templates)

in 1:N identification mode, 2.8” QVGA color touchscreen and buzzer

250,000 IDs in authorized user list, 1 Million logs. CPU: ARM Cortex-

A9 core 1GHz, Linux Operating System, Fake finger detection,

Duress finger, FBI PIV IQS certified optical fingerprint senso,

2 Network / Communication: - Ethernet, RS485, USB, Wiegand and No's 1 95,137.00 95,137.00

OSDP support ,Integrated Smart Card Reader, Internal storage

capacity: 512MB Flash, 512MB RAM, Operating conditions: -

Temperature: -20°C to 55°C (-4°F to 131°F) - Humidity: 10% to 80%

(non condensing), Ingress protection: IP65, EMC/Safety standards: -

CE, CB, FCC, BIS - UL294 , RoHS, REACh and WEEE etc all

SITC of Smart card Frequency Excitation (13.56 MHz) Mifare smart

Card , distance upto 2.5" Memory Type EEPROM, 2K bit memory

Complies with ISO/IEC standards for thickness. Lifetime Warranty

etc all complete

SITC of SS Based Exit Push Button Stainless Steel etc. as per

specifications etc all complete

SITC of Emergency Glass Break Unit Single Pole as per

specifications etc all complete

SITC of Electro Magnetic Lock Double Leaf/ Single Leaf as per door

design, Fail safe type, Holding force: 272kg(600lbs), Inbuilt Door

contact , Current Drain:320mA/12VDC, Built-in voltage spiker

suppressor to protect the lock body and equipments, lock body and

armature with chemical plating anticorrosion finished, With LED light

& brackets UL Listed etc all complete

SITC of 4 core 1.5 Sqmm shielded communication multi-stand Data

Cable (as per actual) etc all complete

SITC of 3 core 1.5 Shielded communication multi-stand Data Cable

(as per actual) etc all complete

Digitally signed by SAKET

SCHEDULE OF QUANTITIES: FIRE PIPING, HYDRANTS, SPRINKLERS AND ACCESSORIES

S No DSR 2022/ DESCRIPTION QTY UNIT RATE TOTAL TOTAL AMOUNT

S No DSR 2022/ DESCRIPTION QTY UNIT RATE TOTAL TOTAL AMOUNT

DSR (INR) NON-DSR (INR)

Providing, laying, testing & commissioning of 'C' class

heavy duty MS pipe conforming to IS 3589/IS 1239

including Welding, fittings like elbows, tees, flanges,

18.7 tapers, nuts bolts, gaskets etc. and fixing the pipe on the

1 wall/ceiling with suitable clamp/support frame and

painting with two or more coats of synthetic enamel paint

of required shade complete as required :

Providing, fixing, testing & commissioning of 15mm dia

18.21 quartzoid bulb type sprinklers of rating 68 degree

centigrade with required accessories :

18.21.1 Pendant type 31 Each 522.00 16182.00

Supplying, installation, testing & commissioning of

sprinkler flexible pipe (UL Listed) of stainless steel

complete with 15 NPT on reducer thread with maximum

working pressure of 175 PSI test pressure of 875 PSI

(Burst) with branch line (Inlet) 25mm NPT male thread to

sprinkler head (Outlet) 15mm NPT female thread with

reducer, nipple, 2 side brackets, center bracket, stockbar

of following sizes complete as required.

Providing and fixing ISI Marked of approved make Fire

4 Extinguishers complete with all accessories as per

manufacturer's specifications.

a) CO2 gas nozzle type - 9 Litre capacity (IS:15683). 1 NOS 12912.00 12912.00

Mechanical Foam gas cartridge type. 9 Kg capacity

ABC dry powder stored pressure type 6 kg capacity

Digitally signed by SAKET

SCHEDULE OF QUANTITIES: AV SYSTEM

S No Item Description UoM Qty Rate DSR Amount NDSR Amount

SITC of 86" Professional Ultra HD Display Panel, 4K UHD (3840x2160) Resolution,

Brightness 400 Nits, Dynamic Contrast Ratio: 500000:1, Viewing angle (horizontal /

vertical): 178 / 178 degree, Display Colours: 1.07 Billion, Panel technology: IPS /

Direct LED, Contrast ratio (typical) 1200:1, Connectivity: Video Input: 2 HDMI 2.0, 2

USB 2.0, DVI-I, Audio In, Audio Out, COntrol: RS232, Ethernet, 2x10W Built-in

speakers, CE, FCC, Class A, BIS Certified etc all complete

SITC of 75" Professional Ultra HD Display Panel, 4K UHD (3840x2160) Resolution,

Brightness 400 Nits, Dynamic Contrast Ratio: 500000:1, Viewing angle (horizontal /

vertical): 178 / 178 degree, Display Colours: 1.07 Billion, Panel technology: IPS /

2 Direct LED, Contrast ratio (typical) 1200:1, Connectivity: Video Input: 2 HDMI 2.0, 2 No's 2 2,46,665.00 4,93,330.00

USB 2.0, DVI-I, Audio In, Audio Out, COntrol: RS232, Ethernet, 2x10W Built-in

speakers, CE, FCC, Class A, BIS Certified etc all complete

SITC of Fixed Wall Mount, capable of holding up to 75 kg and supports 37" to 100"

displays, VESA Compliant etc all complete

SITC of Wireless Presentation Platform, allows simultaneous content sharing for

up to four 1080p presenters, Wireless screen casting with iOS, Android, Mac,

Chromebook, and Windows devices through native AirPlay, Google Cast, or

Miracast protocols, Supports YouTube Live streaming, Local storage available for

playback of images and video, WPA2-PSK, and AES-128 encryption etc all

SITC of Cable Cubby with flip top, cover and 6 Pass Through Holes for multi-format

5 cables, 2 Universal Power Socket , 1 HDMI, 1 USB-C for Data Transfer, made of No's 4 26,250.00 1,05,000.00

aluminium etc all complete etc all complete

SITC of All in One Conference Unit, Camera Sensor 1/2.5″, CMOS, Effective Pixel:

8.0M, 4 x MEMS mic array, AEC | ANS | AGC 180° Pickup Angle pickup Range: 5-

6 8m (16-26ft) A.I. camera with smart backlighting, auto-framing, speaker & No's 2 2,39,335.00 4,78,670.00

presenter tracking, Inputs / Outputs 1x USB-C Input with Alt-Mode, 1x HDMI Input,

1x HDMI Output etc all complete

SITC of 1080p60 PTZ Camera with USB 3.0, HDMI Out, Auto Framing & Presenter

Tracking, Lens 12x, f=3.5mm ~ 42.3mm, Zoom Optical: 12x | Digital: 16x, Control

is support via RS-232 or LAN via the industry standard VISCA protocol etc all

SITC of Universal Switcher with HDMI and USB-C connectivity, 2 HDMI Inputs, 2

USB-C connectivity (4K Video, Audio, Data, Power charge), 2 HDMI Outputs, 4

USB-A 3.0 Connection (for USB Devices), 2 USB-B 3.0 Connection (for PC hosts),

8 USB host switching, Analog audio de-embedding, Charging via USB-C up to 60w, No's 1 4,02,000.00 4,02,000.00

Supports HDMI 4K signal formats (4K UHD @60Hz RGB 4:4:4, up to 18 Gbps),

DP Alt Mode, HDMI 2.0, HDMI 1.x, DVI Signal Support, HDCP 1.x, HDCP 2.2

support etc all complete

Digitally signed by SAKET

SCHEDULE OF QUANTITIES: AV SYSTEM

S No Item Description UoM Qty Rate DSR Amount NDSR Amount

SITC of The Ceiling mic should be easily mountable on any kind on ceiling with the

least visible intrusion and effect to aesthetics. The ceiling mic should offer ease of

connection for setup and maintenance. It is desired that the mic supports Ethernet

based technologies like PoE and Dante for easy and efficient audio routing.

1. The Ceiling mic should support highly directional speech pickup from individual

talkers in the room.

2. 1 mic should be able to cover minimum 500 Sq. Feet

2. Upto 3 talkers around the room should be covered simultaneously.

3. Talker coverage should be customisable and switchable as per the seating

4. The microphone should be programmable to enable maximum noise rejection

from areas in the room with unwanted noise. (e.g pantry, traffic etc.)

The Ceiling mic should be able to efficiently support voice lift & Sound

reinforcement to aid the farthest listener within the room.

The Ceiling Mic should support easy and robust integration with industry leading

Video Conferencing systems, Sound processors and Room Control applications.

The Product should be certified to work with Industry standard Video conferencing

solutions. It should seamlessly support speech based talker tracking with third

party camera control solutions. The solution should include Ceiling Mount bracket

and mute controls on the table/wall in the room. etc all complete

SITC of Audio, Video and Control (AV&C) Processor, 64 x 64 networked audio

channels, 8x on-board Flex channels and GPIO, Full-featured Control engine (with

feature license), 8 AEC Processors, up to 32 x 32 Dante audio channels (8 x 8

included), USB AV bridging (8 x 8 audio + Camera support), Full-featured Q-SYS

Control engine (with optional feature license), External USB audio device host, Up

to 2x VoIP instances etc all complete

SITC of 6.5-inch, 2-Way Ceiling Speaker, Rated Power: 60W, Frequency Range:

65 Hz – 20 kHz, Sensitivity: 88 dB, Rated Coverage 135° conical DMT, Maximum

11 continuous SPL 106 dB, Nominal impedance: 8 / 16 Ohm, Transformer taps: 60W / No's 4 35,333.00 1,41,332.00

30W / 15W at 100 / 70V, IP-34 Rated, Low-saturation and low-loss 70/100V

transformers with 16Ω bypass, UL and CE Certified etc all complete

SITC of 4 Channel Class-D Amplifier, Power (per channels driven): 200 W at 8 Ω /

4 Ω / 100V / 70V, FlexAmp Technology, Frequency Response: 20 Hz – 20 kHz,

12 Signal to Noise > 103 dB, Input impedance >10k, balanced or unbalanced, User- No's 1 2,53,333.00 2,53,333.00

configurable operating modes, UL, CE, RoHS/WEEE compliant etc all complete

SITC of 10.2" Apple iPad LED-backlit Multi-Touch display with IPS technology with

User Control Interface (UCI) Deployment etc all complete

SITC of Apple docking and charging station with all required accessories etc all

Digitally signed by SAKET

SCHEDULE OF QUANTITIES: AV SYSTEM

S No Item Description UoM Qty Rate DSR Amount NDSR Amount

SITC of 8-Port Gigabit PoE+ Ethernet Smart Switch with 2 SFP Ports and Cloud

Management etc all complete

16 SITC of Wireless Access Point etc all complete No's 1 19,333.00 19,333.00

SITC of 1 Meter Premium High Speed HDMI 2.0b Flexy Cable, Bandwidth up to

17 18Gbps, Up to 4096x2160@60Hz at RGB 4:4:4 video resolution, High Dynamic No's 8 4,995.00 39,960.00

Range (HDR10), Dolby Vision and Hybrid log–gamma (HLG) video etc all complete

SITC of 10 Meter Active Copper HDMI Cable, Data Rate: Up to 18.2Gbps, Colour

Depth: Up to 16 bits, Colour Formats: RGB 4:4:4 / Y’CBCR 4:2:2 / Y’CBCR 4:2:0,

18 Consumer Electronic Control (CEC), Auto Lip-Sync Correction, Audio Return No's 4 22,666.00 90,664.00

Channel (ARC), Enhanced Audio Return Channel (eARC), High Dynamic Range

(HDR) etc all complete

SITC of 1 Meter USB Full-Featured Type-C cable for USB 3.1 Gen2, 4 Lane

Displayport Alt mode (4K60FPS Video and Audio), Supporting peripherals via USB

2.0 up to 480 Mbps (Mouse, Keyboard, Thumb Drive, Speakerphone and

Webcam) etc all complete

SITC of 15 Meter USB 3.1 Gen1 SuperSpeed Active Extension Cable TypeA/male

20 to TypeA/female, Supports 4K Webcam, SSD storage, Native USB2/USB1 and No's 3 1,06,666.00 3,19,998.00

USB3 extension, Plug and play compatible with PC, Mac, and Linux etc all

SITC of 2 Conductor 16 AWG Speaker Cable, stranded Bare copper conductors,

PVC/Nylon insulation, PVC jacket (as per actual) etc all complete

SITC of Category 6A Cable, 4 Pair, S/FTP, PVC jacket (as per actual) etc all

23 SITC of Various Cables & Connectors etc all complete No's 4 19,500.00 78,000.00

SITC of 16U, Equipment Rack, with Front & Side doors, 4 No Fan Assembly, on

Top of the Rack, 4 Caster wheels, 2 no Shelfs to mount the equipments which are

not rack mounted, 8X2, 5/6 Amp. Power Distribution Unit, Cable Manager &

Sufficient Rack hardwares etc all complete

Digitally signed by SAKET

SCHEDULE OF QUANTITIES-ART WORKS

S NO MR DESCRIPTION UNIT QUANTITY RATE

DSR (INR) NON DSR (INR)

Hand painting directly on wall creating design and creation of Art work concept on given subject.

With initial visit to site, preparation of various designs with different material, providing the

1 MR samples, layout for approval, improvisation in short listed creative’s and making of final layout for sq m 4 14144.00 56576.00

final production by enlargement of drawing as per ratio of actual size, to prepare detailed working

shop drawings (full scale) based on the Concept drawings.

Mixed media mural Wood/metal/fiberglass/terracotta /tiles or anything other medium artist find

suitable as long as it is permanent in nature.

Metal Sculpture permanent in nature

Concept Creation

Creating design and creation of Art work concept on given subject. With initial visit to site,

preparation of various designs with different material, providing the samples, layout for approval,

improvisation in short listed creative’s and making of final layout for final production by

enlargement of drawing as per ratio of actual size, to prepare detailed working shop drawings (full

scale) based on the Concept drawings/ Views/ site conditions, display of actual size dummy/

3 MR mock up Fabricated in sun board with digital print for client approval cum 1 131995.00 131995.00

Artwork Execution

Execution of approved design in SS 316 grade steel /SS 304 grade SS (1.5mm-2mm thick)/

STONE/ ALLUMINUM/ MIXED MEDIA METAL pu colored (IF REQUIRED) antique as per

approved finish (MRF/ Akzonobel) and protected against discoloration by sealing it with top coat

of MRF/ Akzo nobel clear Pu. Proper support system will be given as per approved shop drawing,

to withstand high wind pressure. The sculpture will be free from any Undulation /Dent unless it is

part of the design. The cost is inclusive of transport/packing and installation of the same at site.

Providing and fixing theme artwork/ any other as per direction and site requirement from the local

4 MR artisans as per the selection of the client and the architect.

Panels of various sizes No. 5 5334.00 26670.00

Providing and fixing CANVAS painting of different sizes as per the selection and approval of

TOTAL ART WORKS 0.00 313151.00

37 Digitally signed by SAKET

SCHEDULE OF QUANTITIES: FURNITURE

S.NO DESCRIPTION OF ITEM IMAGE/ DRAWING QTY UNIT RATE AMOUNT

Providing and placing in position of main table with overall size of table 2100x 2250 x 750mm. The main table shall be of size 2350 x 1150 x 750mm. The side

unit shall be 1200 x 600 x 750mm. The table is made of 25 mm thick MDF – one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC

membrane pressed on to top. Soft closing access flap within-build power box are provided on work surface for wire management. The ERU top is made of 25

mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm

thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure is made of 25 mm thick

Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre- NOS 1,34,809.00 2,69,618.00

laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick MDF one

side pre-laminate board with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses powder coated 400 MM long

metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening.

Pedestals are provided with lock for security.Product is Greenguard and GRIHA Certified.

Modular Workstation Size 1200X 600 X Ht 1200 with KBPT,Pedestal and CPU torlley, Extended Side Panels of 4ft Width:Providing and placing panel & tile

based modular workstation, with partition thickness as 52.4 mm thk and ht - 1200 including powder coated aluminium trims.Tiles: Combination of top tiles are

fabric magneitc/fabric/fabric tackable/white board/glass writing board/ clear glass tile/ plain metal/ prelam tile. Bottom tiles - Plain metal/ fabric

magnetic/fabric/laminated/prelam.SPLIT Tiles: Combination of two finishes for the top tiles on the user side shall be split fabric magnetic/fabric tackable/white

board/prelam/ plain metal along with split fabric magnetic/fabric tackable/white board/prelam/ plain metal. INTERMEDIATE BLOCKS Intermediate blocks are

given in fabric/DL + Fabric/DL finsh.Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto

2 the panels through concealed conduits inside the blocks.HALF SCREEN WITH FRAME - at intermediate position between 2 people and at the end above 17 NOS 54,899.00 9,33,283.00

worktop in clear glass/fabric tackble /laminate/white board finsh.Side panels or legs - out of 25 mm thk prelam particle board with flat pvc lipping edge banding

considered only on the open end conditions or metal powder coated legs at the end and shared condition.extended side panel of 4 ft width. System shall also

have 120 mm high powder coated standalone panel legs to give the system an elevated look.Worksurface - out of 25 mm thk prelam particle board with flat pvc

lipping edge banding of size 1200 mm w x 600 mm d.CPU trolley - with castors.KBPT with/without mousetray - plastic/metal/articulated.The product should be

Greenguard ,BIFMA LEVEL, AIOTA,GRIHA, SCS IAQ, GREENPRO certified.

Supplying and Placing a Reception table of size 2400 X 1770 X 1080 MM, Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade

confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access Flap provided on work surface for wire management. Power box

made with 0.8 mm thick CRCA (IS: 513), with switch plate (8+3 Module cutout provision for Anchor Roma). This is fixed with worktop along the width at Access

Flap position Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2

mm thick PVC lipping. Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with

matching 2 mm thick PVC lipping.Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge

banded with matching 2 mm thick PVC lipping Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990,

Edge banded with matching 2 mm thick PVC lipping.**Drawer bottom is made of 5.5thk MDF whiteboard Handle is provided for ease of opening. HDU and

Drawer is provided with cam lock for security Wire Riser made of 0.8mm CRCA (IS-513) is provided for proper wire management. Organizer Plate made of

1.2mm CRCA (IS-513) is provided for magnetic sticky notes. Bag Hanger Hook made of 1.2mm CRCA (IS-513) is provided for bag hanging. Company should

be ISO-9001, 14001, 45001,50001, Greenguard, BIFMA and AIOTA certified. Product should be Greenguard (UL) certified. Company and Product Certificate

Must Be Certified from Valid Authorised Laboratories.Product is Greenguard , SCS Indoor Advantage Gold certified.

HIGH BACK CHAIR FOR CABIN

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat inner(material-polypropylene) with moulded

polyurethane foam and polyster fabric. the net back should made up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered

using polyester mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-51.0cm x (D)-49.0cm. The supprot

spine should made up of high pressure die cast polished aluminium. Armrest is having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height

adjustment shall be provided in aluminium structure of armrest which is connected to aluminium back spine and is operated with button. Armtop is made up of

PU molded over plastic inner. The mechanism shall be Active BioSynchro Mechanism. The mechanism of chair shall have following features:360 degree

revolving type, Seat/Back tilt ratio of 1:2, Active Bio-Synchro mechanism, 5 position tilt limiter giving option of variable tilt angle to the chair. Front-Pivot for tilt

with feet resting on ground and continious lumber support should ensure more comfort. The mechanism housing should made up of HPDC Aluminium and black

powder coated. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast

polished aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors).

The twin wheel castors shall be injection moulded in black polypropylene. The lumbar support assembly should consists of lumber spine(material-glass fiber

filled nylon) which is fixed to Aluminium back spine. The neckrest assembly consists of upholstered neckrest inner(material-poly propylene) with moulded

polyurethane foam and polyster fabric. upholstered inner shall be fixed to neck rest cover. neckrest shall be fixed to back assembly through neckrest spline.

Overall dimensions of Chair shall be, Width of Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below. Height from ground - min 109.3 to

max 124.4 cm. Seat height - min 45.5cm to max 55.5cm. Dimensions tolerance / variations shall be within +/- 1 cm. Product is Greenpro, UL Greenguard Gold,

GRIHA, SCS Indoor Advantage Gold, BIFMA Level 2 Certified.

38 Digitally signed by SAKET

SCHEDULE OF QUANTITIES: FURNITURE

S.NO DESCRIPTION OF ITEM IMAGE/ DRAWING QTY UNIT RATE AMOUNT

VISITOR CHAIR FOR CABIN

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat inner(material-polypropylene) with moulded

polyurethane foam and polyster fabric. the net back should made up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered

using polyester mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-51.0cm x (D)-49.0cm. The supprot

spine should made up of high pressure die cast polished aluminium. Armtop is made up of PU molded over plastic inner. The lumbar support assembly should

consists of lumber spine(material-glass fiber filled nylon) which is fixed to Aluminium back spine. Overall dimensions of Chair shall be, Width of Chair - 70.5cm,

Depth of Chair - 70.5 cm as measured from pedestal below. Height from ground - 99.0cm. Seat height -49.0cm. Dimensions tolerance / variations shall be

within +/- 1 cm. Product is Greenpro, UL Greenguard Gold, GRIHA, SCS Indoor Advantage Gold, BIFMA Level 2 Certified.

Providing and Placing in Position High Back Chair. The cushioned seats shall be made of injection moulded plastic outer and inner. Plastic inner shall be

upholstered with pure leather and moulded high resiliance polyurethane foamof Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of

compression. Seat size shall be 47.6 cm W x 49.2 cm D. The back shall be cushioned and shall be made up of PU foam with insitu moulded MS ERW round

tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with pure leather. Back size shall be 47.5 cm W x 77 cm D. The armrest top shall be moulded from

polurethane, and shall be upholstered with pure leather and mounted on ot a drop lift adjustable type tubular armrest support made up of Ø3.81±0.03 cm x

0.2±0.01 cm thick MS ERW tube having chrome plated finish. The armrest hieght shall be adjustable upto 6.5±0.5 cm in 5 steps. The adjustable tilting

mechanism shall be designed with the following features : 360° revolving type, front-pivot for tilt with feet resting on ground and contionuous lumbar support

ensuring more comfort, Tilt tension adjustment can be operated in seating position, 5-position tilt limiter giving options of variable tilt angle to the chair,

6 seat/backtilting ratio 1:2, the mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment shall be integrated in the seat 11 NOS 52,730.00 5,80,030.00

through a sliding mechanism. Seat depth adjustment range shall be 6.0±0.5 cm. Back frame shall be connected to the up/down mechanism housed in plastic T

spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. the pneumatic height adjustment shall have an

adjustment stroke of 10±0.3 cm. The pedestal shall be high pressure die cast polished aluminium and fitted with 5 nos. of twin wheel castors. The pedestal shall

be 65.0±0.5 cm pitch centre dia. 5 nos. of twin wheel castors shall be injection moulded in plastic having 6.0±0.1 cm wheel diameter and assembled to

pedestal.Product is BIFMA level 2 , SCS Air Quality index certified.

SEAT ASSEMBLY: The seat is made up of 1.5 ± 0.1 cm thick hot - pressed

plywood upholstered with fabric and moulded polyurethane foam.

SEAT SIZE: 51.8cm (W) x 49.7cm (D). BACK ASSEMBLY: The Back is injection moulded in glass filled Nylon which is

upholstered with Mesh fabric.The back consist of adjustable Lumbar support made of

injection moulded Polypropylene having an adjustment of 5.0 ±0.1 cm.

BACK SIZE: 47.9 cm(W) x 66.9 cm (H)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is

moulded with density 45+/-2 kg/m³ and hardness 14 ± 2 kgf as per IS:7888 for 25%

compression. ARMRESTS (ADJUSTABLE) :The height adjustable armrest is made of Polypropylene

and can be adjusted to 6.0±0.1cm height.It also has swivel and To and Fro adjustment

with moulded PU armtop. ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism is designed

7 with the following features: 17 NOS 15,374.00 2,61,358.00

· 360° revolving type

· Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring

· Tilt tension adjustment can be operated in seating position.

· 5 position Tilt limiter giving option of variable tilt angle to the chair.

· Seat / back tilting ratio of 1:2.

· The mechanism housing is made up of HPDC Aluminium & black powder coated

(DFT 40 to 60 micron.PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass-filled

Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is Ø66.1 ± 0.5 cm.(76.1 ± 1.0 cm. with castors).TWIN WHEEL CASTORS: The twin

wheel castor.Product is SCS Indoor Advantage Gold certified.

SOFA FOR PRESIDENT ROOM

Providing and placing in position of 3 seater sofa. The overall dimensions of the sofa shall be 2060W x 905D x 855H. The seat should be made of PU foam with

Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2)

BACK FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr,

upholstered with fabric or leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and termite

proof as per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is NOS 51,482.00 1,02,964.00

mounted over understrucrure for cushioning effect. It should be a welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

39 Digitally signed by SAKET

SCHEDULE OF QUANTITIES: FURNITURE

S.NO DESCRIPTION OF ITEM IMAGE/ DRAWING QTY UNIT RATE AMOUNT

SOFA FOR RECEPTION & CABIN

Providing and placing in position of 1 seater sofa. The overall dimensions of the sofa shall be 860W x 905D x 855H. The seat should be made of PU foam with

Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2)

BACK FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr,

upholstered with fabric or leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and termite

9 proof as per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is 6 NOS 32,264.00 1,93,584.00

mounted over understrucrure for cushioning effect. It should be a welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic

endcap.Complete all as per the direction of Engineer in Charge.

Providing and placing in position Centre Table having a size of : 1000mm(L) x 600mm(D) x 425mm(H). Understructure of the table which includes Legs, top

wooden frame & bottom tie members are made out of first quality rubberwood of approved make without knots &defects on all faces. Bottom tray is made of

1.2mm thick MS sheet. Metal brackets are used for assembly purpose. Top: 8mm thick toughened glass of approved make. Construction: Knock-down

assembly.Wooden members are PU painted with hardness-2H. Metal components are powder coated. Bottom MS metal tray is having floral pattern laser-cut.

10 Top glass is having sand blasted floral pattern on bottom surface 5. Hardware: Knock-down assembly with high quality standard hardware like screws, metal 2 NOS 29,106.00 58,212.00

inserts, wooden dowel, plastic leg bush. Complete all as per the dimension of Engineer-in-charge.Complete all as per the direction of Engineer in Charge.

Providing and placing in position Centre Table having a size of : 1000mm(L) x 600mm(D) x 425mm(H). Understructure of the table which includes Legs, top

wooden frame & bottom tie members are made out of first quality rubberwood of approved make without knots &defects on all faces. Bottom tray is made of

1.2mm thick MS sheet. Metal brackets are used for assembly purpose. Top: 8mm thick toughened glass of approved make. Construction: Knock-down

assembly.Wooden members are PU painted with hardness-2H. Metal components are powder coated. Bottom MS metal tray is having floral pattern laser-cut.

Top glass is having sand blasted floral pattern on bottom surface 5. Hardware: Knock-down assembly with high quality standard hardware like screws, metal

inserts, wooden dowel, plastic leg bush. Complete all as per the dimension of Engineer-in-charge.Complete all as per the direction of Engineer in Charge.

Overall Size : Width : 120cm Depth : 60cm Height : 37.8cmTABLE METERIALS & SIZE :TOP: SOLID VENEER MDF TABLE TOP WITH 18 mm . LEGS: SOLID

RUBBER WOOD.Color : CAPPUCINO+B15

Overall Size : Width : 53cm Depth : 45cm Height : 45cmTABLE METERIALS & SIZE :TOP: SOLID VENEER MDF TABLE TOP WITH 18 mm . LEGS: SOLID

RUBBER WOOD.Color : CAPPUCINO

Providing and placing in position Conference table. The overall size of the wortop shall be 3000mm x 1150mm x 740mm. Worktop shall be made from 25mm

thick MDF one side prelaminate board with 0.4mm PVC membrane pressed on to top and having chamfered edge. Soft closing dual access flap provided for

access to power supply and data cables. The Under-structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved

shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom

edges for improving the aesthetics.The product has a knock-down construction. A wire raiser made of 0.8mm CRCA MS IS:513. It is epoxy polyester powder

coated (DFT 40-60 microns) for flow of wires and cables. A Power box with 2 cutouts on either sides for standard 8 module Anchor Roma is provided. Beside

each cutout, an additional cutout with plate is provided for mounting Audio Visual Cables (e.g. HDMI,VGA-A,etc).

Company Certificates: Company should be ISO-9001:2015, ISO-14001:2015, ISO-45001:2018, Greenguard (UL), BIFMA and AIOTA certified.

Product Certificates:GRIHA, Greenguard (UL), GreenPro, SCS Global IAQ - Gold. Complete all as per the direction of Engineer-in-Charge.

40 Digitally signed by SAKET

SCHEDULE OF QUANTITIES: SIGNAGE

S No Description Unit Qty Unit price DSR Amount Non-DSR Amount

1 RECEPTION 3D ACRYLIC SIGNAGE

Providing, fabricating and fixing of 3D Acrylic Letters raised 1.5 inches of required size and shape with

arrangement of screws in the letters itself for mounting on the walls or pasting using 3M VHP Tape. Fixing

complete as per directions of the engineer. The Sizes would be calculated in Sqft as per Logo Design

provided. Each 1 35,976.00 35976.00

Tentative Size 42"X60"

2 NAME SIGNAGE CHANGEABLE (All Floors)

Providing and fixing of Acrylic signage made of 3mm Acrylic with textured wood finish pasted /White milky

acrylic 3mm laser cut pasted on top with proper names/ Departments written using plottercut vinyl or laser cut

acrylic letters in approved colour.Inserting provision for changing names .Fixing provision using 3M VHP Each 5 1,967.00 9835.00

double sided tape as required.

Signage Size 12x5 inch

FIRE EVACUATION MAP / SIGN.

Providing and fixing of Clear Acrylic sandwich frame of 3mm & 2mm acrylic with Evacuation Plan Printed on

photoluminescent media and inserted between the two frames. Should be fixed on the wall using 4 Screw/ SS Each 2 2,673.00 5346.00

studs. Size 12 inch x 17 inch

4 FIRE ESCAPE EDGE-LIT SIGNAGE

Providing and fixing of Edge-Lit signage with battery backup. Made from acrylic sheet of 8 mm thickness

laser engraved, Transformer to be inbuilt. Maintenance - free sealed nickel cadmium battery included •

120V/277V AC Operation • Crystal clear acrylic face panel• Engraved letters increase visibility • Anodized

aluminum faceplate • Field applied chevron directional indicators simplify installation • Long life, energy-

saving LED lamps • Dual-voltage 120V/277V AC Operation • UL listed. To be installed at stairs entry. Size

5 FIRE SAFETY SIGNAGE

Providing fabricating and fixing of signage 05 mm thick Acrylic / Sun board sheet at base with

photoluminescent film self adhesive & colored vinyl ( Red/Green) Plotter cut and pasted on top. Both side /

Single Side facing Complete including fixing on wall with screws and washers or hanging on ceiling with GI

chain/GI Bar complete as per technical specifications and directions of Engineer.

Photoluminescent signages Each 2 536.00 1072.00

TOTAL 58807.00

41 Digitally signed by SAKET

SCHEDULE OF QUANTITIES: LANDSCAPE

Product Non DSR

S NO Image Description Unit Qty Rate DSR Amount

“FRP Planters; Supply, Testing and

Commissioning of FRP Planters. The Planters

can be used both Indoor and Outdoor. The

Planter Planters are handcrafted in India. It is made

1 Plain - using Fibre Reinforced Plastic (FRP) and has Nos. 2 3,844.00 7,688.00

14x14x14 features such as Light in Weight can withstand

various Environmental Conditions such as

Harsh weather, UV Rays and Moisture. It has

Fungus, Fire and Frost Resistance. In Terms of

Sustainability, Fibre is considered to be Eco-

Friendly and can be Recycled."

“FRP Planters; Supply, Testing and

Commissioning of FRP Planters. The Planters

can be used both Indoor and Outdoor. The

Planter Planters are handcrafted in India. It is made

2 Wave - using Fibre Reinforced Plastic (FRP) and has Nos. 2 7,047.00 14,094.00

17x18 features such as Light in Weight can withstand

various Environmental Conditions such as

Harsh weather, UV Rays and Moisture. It has

Fungus, Fire and Frost Resistance. In Terms of

Sustainability, Fibre is considered to be Eco-

Friendly and can be Recycled."

“FRP Planters; Supply, Testing and

Commissioning of FRP Planters. The Planters

can be used both Indoor and Outdoor. The

Box Planter Planters are handcrafted in India. It is made

18x18x18 using Fibre Reinforced Plastic (FRP) and has

features such as Light in Weight can withstand

various Environmental Conditions such as

Harsh weather, UV Rays and Moisture. It has

Fungus, Fire and Frost Resistance. In Terms of

Sustainability, Fibre is considered to be Eco-

Friendly and can be Recycled."

42 Digitally signed by SAKET

SCHEDULE OF QUANTITIES: LANDSCAPE

Product Non DSR

S NO Image Description Unit Qty Rate DSR Amount

Providing & fixing Artificial silk plants with

combination 3 or 4 types uniformaly ditributed

plants on wall as well as ceilig suspended

creepers with necessary wire or hangin

arranement included. Plants which ultraviolet

4 blocking chemicals are impregnated into the Sqm 5 6,214.00 31,070.00

materials during the manufacturing process.

These chemicals are blended with the plastic or

PVC parts Installation Installation is done on

Waterproof ply board with staple gun machine.

1Sq Mtr X 1 Sq Mtr

Providin & fixing Artificial silk plants with

combination 3 or 4 types uniformaly ditributed

plants on wall as well as ceilig suspended

creepers with necessary wire or hangin

arranement included. Plants which ultraviolet

5 blocking chemicals are impregnated into the Sqm 5 2,370.00 11,850.00

materials during the manufacturing process.

These chemicals are blended with the plastic or

PVC parts Installation Installation is done on

Waterproof ply board with staple gun machine.

Supply of textured stone or solid finished, light

weight (Pls choose : shape: round/ oval/

rectangular/ conical/ elliptical) (Pls choose

:volume : xxx ltrs) (Pls choose :color: beige/

white/ grey/ black) full bodied, exterior grade,

joint/ layer free, homogeneous planters made

with premium quality LLDPE polymer

manufactured with precision rotational moulding

6 process. The planters shall be made of 100% Nos 2 28,186.00 56,372.00

recyclable content, industrial grade quality

polymer, non- metallic, shock proof, asbestos

and glass fiber free compounds. Planters shall

be rust proof, UV-resistant, anti-frost, no peeling

and easy to clean. OEM / authorized supplier to

provide 1 year warranty against fading & any

manufacturing defect. Design, color and size as

43 Digitally signed by SAKET

SCHEDULE OF QUANTITIES: LANDSCAPE

Product Non DSR

S NO Image Description Unit Qty Rate DSR Amount

Supply of double layered translucent backlit

(Pls Choose : Shape: cylindrical/ elliptical /

conical/ round/ square) hand crafted (dye)

pattern planters of volume Pls Choose :XX

letter; approx. dimension Pls Choose :XXXX in

plain or stone finish. Planters to be indigenously

made by rotational moulding, with homogeneous

100% recyclable, industrial grade LLDPE

polymer mix, with textured surface and stone

7 match finishes. Planters to have concealed Nos. 2 40,998.00 81,996.00

shock resistant back lighting system with

secured supply wire and an integrated water

outlet hole & plug, peel proof construction,

asbestos free, light in weight, without any joints,

rust proof, UV stabilized, anti-frost feature and

easy to clean. OEM / authorized supplier to

provide 1 year warranty against fading & any

manufacturing defect. Design, colour and size

as per selection.

Plantation: Supply and installation of Natural

Plant with sand, fertilizer etc.

44 Digitally signed by SAKET