Special repair for renovation of Mechanical Workshop PWD BR Br. Karnal in Karnal Distt

Amount

Earth work in excavation in foundations, trenches, etc. in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres.(HSR 6.6)

Dismantling brick work, tile masonry or tile lining and tile terracing . (b) in cement,[HSR 8.5(b)]

Dismentling asbestors cement celotax or other hard-board ceiling or partition walls including supporting timber(HSR 8.15)

Removing door and windows (wood and steel) with chowkats by making recesses in walls when the wall is not to be dismantlled:- (HSR 8.18) a)Door

b) Window

c) Ventilator

Scrapping white wash and colour wash[HSR 8.32(a)]

Scraping of cement plaster [HSR 8.32(c)]

Dismantling white or coloured glazed tiles (to be carefully removed) [HSR 8.38]

Cement concrete 1:4:8 with brick ballast 40mm nominal size in foundation and plinth (HSR 10.26)

Cement Concrete 1:2:4 with stone aggregate 20mm nominal size in foundation and plinth l. [HSR 10.38]

Cement Concrete 1:4:8 with stone aggregate 40mm nominal size in foundation and plinth. [HSR 10.39]

Cement concrete 1;2;4 with stone aggregate 20mm nominal size in first storey upto 4 metres above plinth level (HSR 10.59)

Cement concrete 1 : 1½ : 3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respects. [HSR 10.82 + 10.95 (a)]

Cement concrete 1 : 1½ : 3 with stone aggregate 20 mm nominal size for reinforced concrete work for walls exceeding 20 cm thickness (straight and curved) beams,girders, stairs, columns, (square or rectangular) battens and lintels etc excluding steel rainforcement but including centring and shuttering, laid in position, complete in all respects.[HSR 10.86 + 10.95(a)]

Nicking cement concrete surface (over 28 days old) including preparation and laying slurry ( HSR-10.118 LR)

Providing and laying 80mm thick ISI Marked interlocking paver blocks confirming to IS15658:2006 / IRC: SP: 63-2004of all shapes and colours in design mix cement M-40 ovar a bed of 30mm thick fine sand complete in all respect. [HSR 10.159]

First class brick work laid in cement sand mortar 1 : 6 in foundation and plinth (HSR 11.2)

First class brick work laid in cement sand mortar 1 : 5 in foundation and plinth (HSR 11.3)

First class brick work laid in cement sand mortar 1 :6 in first storey upto 4 metres above plinth level [HSR 11.7]

First class brick work laid in cement sand mortar 1:4 in first storey upto 4metres above plinth level ( HSR 11.9)

Providing and fixing PVC rain water pipe 6 Kg. Pressure of ISI mark in cement mortar during masonry work. a) 100mm dia PVC pipe 6 Kg. pressure. (HSR 13.89 a)

Conglomerate floor 40 mm thick cement concrete topping 1:2:4 (HSR 14.9)

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT & JOHNSON. (HSR 14.89)

Providing & fixing vitrified tiles of size 600mm x 600mm of approved make in skirting/dados laid in any pattern as specified over base of 12mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like: NITCO, KAJARIA, SOMANI, ORIENT, RAK & JOHNSON. (Double charged tiles shall be used as approved by Engineer in charge. (HSR 14.90).

Providing and fixing ceramic tiles / anti skid tile of size 400 mm x 400mm or above size of approved make in flooring, laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, RAK & JOHNSON. (HSR 14.91)

Providing & fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (HSR 14.92) a) Size of ceramic Glazed tiles 200 x 300 mm

12 mm thick cement plaster 1:5 on walls (HSR 15.6)

12 mm thick cement plaster 1:6 on walls [HSR 15.7]

15 mm thick cement plaster 1:3 on the rough side of single or half brick wall [HSR 15.9]

15mm thick cement plaster 1:5 on the rough side of single or half brick wall (HSR 15.11 )

Preparation of plastered surface for oil bound distemper including sand papering the surface, applying one coat of linseed oil, and filling with approved quality filler, consisting of white lead , linseed oil,varnish and chalk mitti including finishing the surface to the required finish complete. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.52)

Distempering with dry distemper (of appd. Manufacturer) two coats excluding priming coat on new work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.53)

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.58)

Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). [HSR 16.79 (b)].

Providing and applying two coats white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (Note:- reputed make Putty such as J.K./ Birla shall be used as approved by Engineer-in-charge). (HSR 16.81).

Supplying and fixing glass panes with moulding of commercial hard wood such as hollock, champ, chikrassy and chaplash etc. ( Non coniferous timber other than teak, conforming to I.S. specification No. 1003 kiln seasoned )- ( c) 4 mm thick ( glazing area above 55 sq dm but upto 84 sq dm of each pane) [HSR 17.36( c)]

Factory manufactured panelled door or glazed window, shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash, etc.,(non-coniferous timber other than teak, conforming to I.S. specification No. 1003, kiln seasoned), with 100 mm wide vertical styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 15 mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges, screws, chocks/cleats, stops, nails etc., complete, fixed in position (execluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) [HSR 17.90 (b)(-)Note (i) under item No. 17.18] b) 35 mm thick.

Factory manufactured wire gauze door and window shutters of commercial hard wood, such as hollocks, champ, chikrassy and chaplash, etc., (non-coniferous timber other teak, conforming to I.S. specification No. 1003, kiln seasoned), with 100 mm wide vetical styles, 150 mm wide lock rail, 200 mm wide bottom rail and wire gauze of 140G or 120G designation including cost of iron hinges, screws, chocks/cleats,stops, nails etc., complete fixed in position (execluding the cost of any fittings, other than specified above but including labour for fixing the same in position) [HSR 17.92 (-)Note (i) under item No. 17.18] ii) 35 mm thick.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded build up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS;733 and IS; 1285 fixed with rawlplugs and screws or with fixing clips or with expension hold fasteners inluding necessary filling up of gaps at juncitions, at top, bottom, and sides with required neoprene felt etc. Aluminium sections shall be smooth, rust free straight mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panclling C.P. brass / stainless steel screws, all complete. Fixed portion (Anodised Aluminium transparent or dyed to required shade according to IS;1868, minimum anodic coating of grade AC 15) [HSR 17.95]

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS; 12823 grade 1 type II in paneling fixed in aluminium doors, Windows shutters and partition frames with c.p brass / stainless steel screws etc. complete. (HSR 17.97(b)) Pre-laminated particle board with decorative lamination on both sides.

Steel work, fixed independently without connecting plates, including cutting, hoisting and fixing in position in : - ( c )tees, angles and channels. [HSR 18.1( c)]

Steel reinforcement TMT bars FE-500 FQR /FE-500 D grade or more for RCC work, where no included in the complete rate of RCC including straightening, bending binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights/depths/storeys/basements etc. (HSR 18.22) (Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps, wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing, shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement).

Pressed steel sheet frames (chowkats ), consisting of 2mm thick steel sheet of the specified section,including iron lugs(hold fasts) iron hinges conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for fillings in the frame, and cement concrete 1:3:6 for lugs complete (HSR 18.34) d) Door and window frame of size 114 mm x 50 mm with 35 mm wide double rebate

Preparation of sub grade, including trenching, rough dressing of spoil, final dressing of earth, to given levels and camber, watering rolling with road roller, and compacting the bed. [HSR 24.1)

Providing and fixing in position best Indian make ( to the approval of the Engineer-in-Charge) Indian type Orissa or Orya water closet suite for sinking into floor, with raised foot treads complete with 100mm H.C.I. 'P' trap with or withoput vent as required and all other necessary fittings as fully described in item no. 30.1 above [HSR 30.2 a(i)] a) Size 580mm (i) white

Providing and fixing in position best indian make (as approved by the Engineer-in-charge) European type water closet suit, Syphonic type, consisting of- (i) Vitreous China Ware Syphonic Suite with 15 Liters capacity matching chinaware cistern and all internal brass fittings complete with ‘P’ or ‘S’ trap with or without vent (as approved by the Engineer-in-charge). (ii) One Piece seat and lid in hollow black or white with plastic fitted with chromium plated hinges and rubber buffers,(to the approval of the Engineer-in-charge). Complete in all respects including cutting and making good the walls and floors [HSR 30.5] a) Single trap syphonic W.C. Suite (i) White

Extra over item Nos. 30.1 to 30.4 and 30.6 for providing and fixing 15 litres capacity low level vitreous china ware cistern complete with flush bend all other necessary fittings instead of C.I. High level cistern complete with fittings. [HSR 30.12 (i)] White

Providing and fixing in position best Indian make (ordinary)lavatory suites, consisting of Lavatory in vitreous chinaware size as given below (to the approval of the Engineer-in-charge) including china plug for tap hole where necessary. R.S. or C.I. Brackets for building into wall including painting, 32mm C.P. brass waste with C.P brass chain and rubber plug, 15mm C.P. brass screw down pillar tap with jamnuts or couplings best design (as approved by the Engineer-in-Charge). All fittings best Indian make and; to the approval of the Engineer-in-Charge. All brass work chromium plated and complete in all respect including cutting and making good the walls floors and painting of fittings etc. [HSR 30.41] White (i) Size 450mm x 300mm with one tap.

iv) Size 550mm x 400mm with one no. tap.

Providing and fixing in position best Indian make Soap dish fixed into wall with C.P. brass screws and complete in all respects including cutting and making good the wells etc. [HSR 30.70] a) C.P. Brass (i) Soap dish large

Providing and fixing in position best Indian make bevelled edge 5.5mm thick mirror mounted on asbestos sheet ground fixed in position by means of 4 Nos. chromium plated brass screws and washers over rubber washers and rawl plug embeded in the wall or chromium plated brass clamps with C.P brass screws (as required by the Engineer-in-charge) complete including cutting and making good the walls etc. [HSR 30.71] a) Indian make (i) 600 x 450mm

Providing and fixing in position 15mm i/d C.P.brass & bib cocks of best quality (as required by the Engineer-in-charge). [HSR 30.75] c) Bib cock

Providing and fixing in position C.P. brass stop cocks (as approved by the Engineer-in-charge). [HSR 30.76] a) 15mm stop cock (i) Stop cock male and female end

Providing and fixing HDPE water storage tanks of Sintex, Diplast, O.K. make with covers / lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with sutiable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in-Charge. (except civil work). (HSR 30.119) 500 Ltr.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length (total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape (R.B.T)/Spring core (2.5mm thick) wire of high tensile strength of 165 Kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm / metre (cost of M.S angle, C.C blocks shall be paid separately) N.S (DSR 6.53)

Providing & fixing Colour coated sheets ( PPGL) GAL Value 0.6 mm thickness Sheet for shed with complete fitting from cover including angle, nut, bolts, paints, pipe excavation of earth work, concrete for foundation etc. complete in all respect to the entire satisfaction of Engineer-in-Charge. ( N.S)

Providing for laying, jointing, fixing and testing G.I. (Medium class "B" type of Tata & Jindal make) pipe lines and specials tees bends, sockets, elbows etc. inside building and testing etc. complete including cutting threading. Including cost of Special. G.I. specials shall be of Make:- UNIK, TATA, ZOLOTO. (NS) a) 25 mm internal diameter of pipeline

Earth work non plastic or Tibba Sand under floors taken from outside of campus area with all lead and lift including loading, unloading, laid in 15 cm layer including ramming, watering, consolidating, compaction, and compensation of earth etc., complete in all respect as per the direction of engineer in charge. [NS]. 1 Km. lead

Recovery items:- The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Dismantiling of bricks and Removing of Door and windos in the DNIT. In case it is not possible to use this material on the work, the agency can take away this material after approval from employer. This material will be issued at the price quoted by the agency. However the reserve price is as under:- i) Door @ 800/- Each

ii) Windows @ 500/- Each

iii) Ventilator @ 300/- Each

iv) Good Bricks @ 4.50/- Each

v) Brick Bats @ 450/- cum

vi) Cement Celotax Hard-board @ 20/- sqm Note:- All quantities of the above materials have been worked out on the basis of theoretical quantities laid on this building. However, agency may visit site before quoting rates and assess the extent of retrieved material. There shall be no measurement after actual dismantling and if material after dismantling is found on lesser side, no claim of agency on this score will be entertained and full recovery on the basis of quoted rate and quantity exhibited in the BOQ shall be made. The reserve rates are minimum rates to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price. Note:- 1. In case of any difference in the unit & nomenclature of any of the HSR Items of Civil, P.H. work depicted in this DNIT and that given in HSR, the unit and nomenclature given in HSR shall be applicable. 2. Only reputed make material will be used (make/brand exhibited in HSR and exhibited in approved standard document) as approved by Engineer-in-charge, while executing various items/works at site.

the new aditya cooperative labour and construction society limited karnal