Construction Work

Amount

Dismantling, removing and carefully stacking RCC using deploying machineries etc., complete complying with standard specification and as directed by the departmental officers at site of work. Complete

Dismantling, removing and carefully stacking Doors & Windows including removal of frames, hinges and fastenings etc., Complete

Dismantling clearing away and carefully stacking materials useful for reuse for any thickness of walls. Brick masonry in Cement mortar walls under 3m height etc., complete

Collecting the scattered debries from the campus and conveying away the same to outside by lorry to a lead of 3 km.(Entirely within city limit) including loading un-loading charges and dumping in low places and leveling neatly etc.,complete.

Installation charges inclusive of Transportation to site and the bored pile equipment employed for the works including setting up of pile driving equipment with all accessories and tools at each of the pile location based on the sequence of opearation approved by the departmental Engineers irrespective of the location and distance involved in movement of pile driving equipment etc., complete.

Installation of Vertical Bored cast in situ RCC piles in all types of soils, using Standardised Concrete Mix M30 grade, with sulphate resistant Cement, fine aggregate, 20mm and down graded HBGS jelly coares aggregate. The rate includes cost of reinforcing steel, binding wire, fabrication, welding charges, placing of reinforcement cage in bore hole in correct position, cost of boring to the required depth with Bentonite solution with temprory casing of required length, conveyance of RMC to site and pouring concrete using Tremine pipes, conveyance of all materials to the site including all tools and plants, shifting the plants and equipments from one point to another, excavtion of mud pits for circulation of Bentonite soultion, closing the mud pits to original level and mud removal with initial lead and lift but including dismanteling the concrete above the cut off level etc complete as directed by the departmental officers including socketing. The reinforcement cage should be welded properly for lifting. The concrete cubes to be tested as per IS 456-2000. Acceptance criteria by clause 16.1.

Frequency of testing as per 15.2.2. Testing to be conducted at both the ends at site as well as RMC plant. Pile driving depth should be decided by the departmental officers at site. The length of pile for payment shall be measured from top of shoe to the bottom of the pile cap.

600 mm dia pile having longitudinal main reinforcement of 10/20# with helical reinforcement at 10mm dia at 150mm c/c with inner rings of 12mm dia @ 1000mm c/c with lifting hook of 12mm dia at required length

Initial Load Test as per IS 2911 Part IV 1985 including cost of single pile (250% of pile capacity), labour, reinforcement charges and all other incidential charges including excavation, shoring, strutting, dewatering etc. as necessary hire charges for jacks, measuring devices, Structural Frame work for platform, Kent ledges etc, as required and providing pile cap.

600 mm dia pile

Routine load test as per IS 2911 part IV 1995 (150% of pile capacity) including labour charges for jack, measuring devices, structural frame work plot form, kent ledges etc., as required and as directed by the departmental officers etc. complete.

600 mm dia pile

Pull out test as per IS 2911 part IV 2013 including labour charges for jack, measuring devices, structural frame work plot form, kent ledges etc., as required and as directed by the departmental officers etc. complete.

600 mm dia pile

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Upto initial lift of 2m below ground level

Over the initial lift of 2m below ground level

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in hard rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary refilling the sides of foundation with excavated soil other than sand in layers of 15cm thick well rammed and completed, and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Supplying and filling in foundation and basement with crushed stone dust in layers of not more than 15 cm thick, well rammed watered and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation and basement with filling M sand in layers of not more than 15cm thick, well rammed, watered and consolidated etc., complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:5:10 (One Cement, Five sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation and flooring including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

For Centering for curved surface for all Rcc item works

Providing and laying in position, Standardised Concrete Mix M-40 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 440 kg/mᶾ and maximum water cement ratio of 0.40, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5136 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

above 1.50 m and upto 4.50m below ground level

Foundation basement

Ground floor

First floor

Second floor

Third floor

Fourth floor

Fifth floor

Sixth Floor

Seventh Floor

Eight floor

Nineth floor

Tenth floor

Eleventh floor

Twelveth floor

Thirteenth floor

Fourteenth floor

Fifteenth floor

Sixteenth floor

Seventeenth floor

Eighteenth floor

Providing and laying in position, Standardised Concrete Mix M-20 Grade in accordance using 20mm with IS:456-2000, and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 Kg/M3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cum) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation basement

above 1.50 m and upto 4.50m below ground level

above 4.50m depth upto 9m below ground level

9m below ground level

Plain Cement Concrete 1:2:4 (One Cement, Two sand and Four hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges, centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with Cement Mortar 1:3 (One Cement and Three Sand) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel rod for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

supplying & fixing mechanical couplers for lapping the reinforcement including cutting, threding the reinforcement bars and making an assembly, etc. complete complying with standard specifiction and as directed by the departmental officers

20 mm dia coupler

25 mm dia coupler

Brick work in following Cement Mortar using Fly Ash Bricks of 230 x 110 x 70mm size conforming to IS: 12894-1989 Class designation not less 50 kg./ sq.cm. average compressive strength in cement mortar 1:5 for load bearing structures for foundation and basement and for superstructure including curing, etc., complete complying with standard specifictaion.

Ground floor

First floor

Second floor

Third floor

Fourth floor

Fifth floor

Sixth Floor

Seventh floor

Eighth floor

Nineth floor

Tenth floor

Eleventh floor

Twelfth floor

Thirteenth floor

Fourteenth floor

Fifteenth floor

Sixteenth floor

Seventeenth floor

Brick partition wall using Fly ash bricks of size 230mm x 110mm x 70mm in Cement Mortar 1:3(One cement and three sand) including fixing hoop iron reinforcement if found necessary, laying, finishing and curing etc., complete as directed by the departmental officers. (Cost of hoop iron reinforcement will be paid seperately)

First floor

Second floor

Third floor

Fourth floor

Fifth floor

Sixth floor

Seventh floor

Eight floor

Nineth floor

Tenth floor

Eleventh floor

Twelfth floor

Thirteenth floor

Fourteenth floor

Fifteenth floor

Sixteenth floor

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Ruby red/Raw Silk, with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard specification.

Supplying and fixing fine polished cuddapah slab of 20/30mm thickness for cup-board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as directed by the departmental officers

Nosing to the granite slabs by cutting the granite slabs for 18mm to 20mm thick edges of semicircular shape to required size and nosing with semicircular shape and polishing using hand machine and the nosing with semicircular shape and polishing with hand machine and the nosing is made highly smooth and gloosy . the cost includes labour charges and cost of machineries and polishing charges etc.complying with standard specification and as directed by the departmental officers.

Providing grooving to granite slab at the intermediate edges of the vertical face with neat finishing etc complete with standard specification and as directed by the departmental officers. The cost including higher charges of machines and labour charges etc complete

Paving the floor with Vitrified tiles of size 600x600x10mm of approved colour, shade and quality laid in cement mortar 1:3 (One cement and three sand)20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be Johnson/Kajaria/ Somany/Nitco/RAK or Equivalent which has to be got approved by Executive Engineer before use on works.

Paving the Floor with designed colour ceramic tiles of non slippery type of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.30 Kg./Sq.M. etc. complete complying with standard specification and as directed by the departmental Officers. (The colour and make brand of the tiles should be got approved by the Executive Engineer before use on works)

Dadooing walls with Colour designed digital print glazed tiles, with borders, with size of 300mm x 600mm x 10mm and above set in Cement Mortar 1:2 (One Cement and Two sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be Johnson / Kajaria / Somany / Nitco / RAK which has to be got approved by Executive Engineer before use on works)

Dadooing with special printed design colour glazed tiles of size 300mm x 600mm x 10mm

Providing and Fixing of PVC Trims (Corner beeding) at the outer corner profiles of the tiles including cost of material, labour and handling etc. as directed by departmental engineers at site of work and as per standard specification.

Cladding the vertical wall surface with pre polished ruby red granite slab of size 1200x600 of 18 to 20mm thick of approved colour and best quality free from all defects set in cement mortar 1:2 (one cement and two sand) 10mm thick. The joint shall flush with face or granite slab and in line. The joints shall be pointed with same color pigments mixed with white cement of 1.8 kg/sq.m. The slabs so laid shall be supported with suitable arrangements for a period of 2 hours after laying to avoid falling granite slabs by its self weight after laying its position. The granite slab shall be got approved by the departmental officers before use on works etc complete. The rate is including labour, all material, scaffolding charges, hire charges for granite cutting machine, power consumption etc complete

Paving the Top of roof with Solar refelective ceramic tiles of size 305 x 305 x 7mm thick of approved quality and colour laid in Cement mortar 1:3 (One cement and three crushed stone sand) 12mm thick and pointed with tile grout (Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works)

Brick Jelly Lime Concrete of 1:2:5 (One Lime,Two Sand and Five Brick jelly ) with 40 mm hand broken brick jelly for Sunken portions including dewatering wherever necessary and laid in layers of not more than 15cm thick, well rammed, consolidated and curing etc. complete complying with standard specification.

JOINERIES

Supplying and fixing C. W. Frames for DOORS WINDOWS VENTILATORS and other similar joinery works with the following sizes and sections including labour charges for wrought and put up in position and also for fixing hold fast in frames and masonry etc complete in all floors. Upto 4m Length.

Manufacturing and supplying of 35mm thick solid core block board flush single/double leaves shutters with teakwood ply veneering on both sides hot pressed bonded with liquid phenol formaldehyde resins and external lipping by TW around rebate cutting etc as per IS 2002 part I of 1991 including TW lipping of size 35 x 12 mm including labour charges for fixing all furniture fittings and specials. The flushshutters should be ISI specification and got approved by the Departmental officer before fixing. Alu. fittings of 6" tower bolt -1 no, 4" tower bolt - 1 no, door stopper- 1 no, Aldrop - 1 no , hinges 6 " - 3 nos., ornamental lock and handle etc complete as directed by the departmental officers.

single leaf

Supplying and Fixing of Wood Polymer Composite (WPC) door with solid door frames extruded with size 75mmX50mm. The Inner core made of rigid WPC compound with minimum shore hardness of 55, and Buld Density 750Kg/cub.Mt. The frame shall be fixed to the wall using 10X10mm long MS screw throught the frame by using PVC fasteners. A minimum of 4nos screww to be provided for each vertical members,Door shutter of 25mm thick Wood Polymer Composite (WPC) single core Extruded Door Shutter, with one side digital printing of Specified Design which is approved by engineer-In-Charge. Both side of the shutter shall have rough sugar texture finish, aminated with UV oil. The solid WPC board shall have minimum shore hardness of 55 and Bulk density 550Kg/Cub.Mt moulding the thickness remains 25mm(+/-1mm) etc complete as per the direction of the departmental officers.

Manufacturing, supplying and fixing of Steel doors with following specification. MS angle of size 40x40x6mm at 3.5 kg/m used for outer frame and MS Angle of size 35x35x5mm at 2.6 Kg/m for the shutter frame. Stiffeners with 32x6mm at 1.5 Kg/m MS Flat is provided as the lock rail of the door and welded intact on both ends to the shutter frame. 18 G CR Sheets of best quality is laid as panel in the shutter frames. 18x5mm at 0.70 kg/m MS flat is welded over the 32x6mm at 1.50kg/m MS Flat on the rear side of the door, sandwitching the CR Sheet for rigidity. Additional stiffeners with 18x5mm at 0.7 Kg/m MS flats are provided diagonally on the rear side of the shutter. 300mm length of hinges 2 Nos, for shutter is provided. 6 Nos. of 250mm length hold fasts 200mm length specified at the ends are welded to the outer frame of the door. Tower bolt 2 Nos. at the top provided.

250x16mm size of Two aldrops are provided in single leaf door at lock rail section in the door for inner and outer provided and one rotating locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear sideof the door at an appropriate place and 1 No. of M.S. handle of heavy duty. A tie bar is provided at the bottom of the outer frame to prevent twisting of the frame during transportation and fixing. All members are given one coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation, taxes and all other incidental charges, etc., complete.

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supply and fixing of UPVC (Unplasticised Polyvinyyl Chloride) Louvered ventilaters made of upvc profile section of size 74x60x56mm having outer wall thickness of 2.30mm (+/-0.3mm) with 3 box multi chamber hollow construction and provided with galvanized steel reinforecement at where ever required size of 35x35mm.The shutter of openable window shall be made of size 78x60x40mm having outer wall thickness of 2.30mm(+/-0.3mm) and provided with galvanished steel reinforcement at where ever required of size 25.5x36mm and the fixed mullion of size 72x60x36mm having outer wall thickness of 2.30mm(+/-0.3mm) and provided with galvanized steel reinforcement at where ever required size of 35x17mm. All sections of frames, sash, and mullion shall be reinforced with galvanished mild steel section having wall thickness of 1mm. All the corners / mullion, joints of the frame and sash shall be mitred cut & fusion welded without any mechanical joints. All welded joints are to be neatly trimmed & feature grooved nip finish so as to make the finished products free from all sharp edges. The window frame and shutter shall have water drainage holes to drain the water with cap.

The shutter will be provided with suitable upvc beads of size 34x18mm for glazing for the specified / required glass (single), duly cut at correct degree & fitted with necessary K and O type EPDM weather sealed gaskets. Windows has to be provided with variaty of security device like multi point lock system friction stay and powder coated handles as per the requirement, complaint with relevant specification and as directed by the departmental officers. The complete window shall be fixed into the prefinished opened places, by drilling & fixing through the outer frame using high quality fasteners & silicon sealant is applied to fill up the gap between wall & window frame for leak proof installation, and completion as per the standard specification and as directed by the departmental officers.

Supplying and fixing of M.S.grill of approved design for open courtyard, grill, grill work to doors and window openings etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including cutting the members, welding, grinding, one coat of priming coat using best approved quality red oxide primer, dismantling of walls / concrete if necessary, fixing and finishing the dismantled portion to original condition etc., complete complying with standard specification.

Providing & Fixing Staircase hand rail for staircase made out of 50.80mm dia stainless steel tube of 1.60mm thick at required locations to a height of 1000mm from finished floor level, welded to 38.10mm dia S.S.tube post of 1.60mm thick as vertical at 1m centre to centre with 3 nos of 25.40 mm dia horizontal S.S.tubes of 1.60mm thick in between as per details shown in the drawing and as directed. Rate shall include for grouting into concrete with necessary supporting arrangements in hand rail vertical and in floor, welding the base cup of post into slab reinforcement polishing.buffing and protecting the hand rail surface etc.complete as directed by the departmental officers.

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:3 (One Cement and Three Sand) 20mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Providing, mixing, laying polymer based water proofing treatment for the sunken toilet by applying cement based, flexible,water proofing compound confirming to IS:2645,to a thickness of 1mm of the prepared surface of the roof slab/floor slab as per specifications mentioned above providing cement mortar 1:3, water proofing over plaster to a thickness of 12mm over the membrane coating with admixture of approved make. Rate inclusive of preparation of surface,which includes cleaning of surface polymer mortar curing,labour,tools and equipment,etc., Rate inclusive of cement and sand required for the treatement, the cost and labour charges for fixing 25mm dia pressure pipes 15kg/cm2 to a length of 45 cm for drip pipes etc., complete.

supplying and applying water proofing treatment with membrane type water proofing methods using polymer modified bituminus membrane of maxipro/ polyglass of equivalent make made using atactic poly propolene ( APP ) based with UV resistant, ground chemical resistant, high melting points, flexible and high adhesive strength. the membrane should have 4mm thick and 5.50 kg/sqm weight. the membrane shall be reinforced with non woven polyster reinforcement of minimum 180 gm/ sqm having tensile strength 850 N/ 5cm (L) and 575N/ 5cm (T) including coating with compatiable primer of bituminous base and torch application with overlap of 100mm wherever required. the membrane surface shall be protected with granules. the reinforcement provided shall be able to withstand the traffic flow density after construction and shall carry a minimum guarantee period of 10 years. the rate inclusive cost of membrane including primer and labour charges for laying by loose torching on full surface or at overlap based onsite condition etc., complete.

Painting the wall with Texture Finish Paint including labour charges etc. complete complying with standard specification and as directed by the departmental officers

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt etc., complete complying with standard specification.

Applying two coats of putty for 3mm thickness for interior including labours for grinding the slab joints and with neat finishing etc. complete complying with standard specification and as directed by the departmental officers

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Polishing the teak wood door with two coats of Melamine polish to wood surface as per direction etc., complete should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4kg. / sq.cm including cost of necessary PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cost of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

160 mm dia pipe

INTERNAL WATER SUPPLY and SANITARY ARRANGEMENTS

Supplying, laying and jointing the following UPVC pipes - shedule 80 (brand or equivalent) of following diameter of approved quality and best variety of pipes with pressure withstsnding 10 kg/sq.cm and laid properly above ground level to alignment including fixing of required GI specials but excluding cost of such specials, cutting and threading, including fixing to walls with necessary teakwood plugs clamps and screws making holes in the wall or drilling hole in the roof and making good of the distributed portion in the original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges. The pipes to be painted with two coats of good variety and best quality of synthetic enamel paint over coat of red oxide primer etc. complete in all floors complying with standard specification, (The UPVC pipes shall be got approved by the Executive Engineer before use on works.)

20 mm dia UPVC Pipe

25 mm dia UPVC Pipe

32 mm dia UPVC Pipe

40 mm dia UPVC Pipe

50 mm dia UPVC Pipe

65 mm dia UPVC Pipe

Supplying, laying and jointing the following CPVC pipes (brand or equivalent) of following diameter of approved quality and best variety of pipes with pressure withstsnding 10 kg/sq.cm and laid properly above ground level to alignment including fixing of required GI specials but excluding cost of such specials, cutting and threading, including fixing to walls with necessary teakwood plugs clamps and screws making holes in the wall or drilling hole in the roof and making good of the distributed portion in the original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges. The pipes to be painted with two coats of good variety and best quality of synthetic enamel paint over coat of red oxide primer etc. complete in all floors complying with standard specification, (The UPVC pipes shall be got approved by the Executive Engineer before use on works.)

20 mm dia Pipe

Supplying and fixing in position UPVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the UPVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

UPVC Elbow

65mm dia

50mm dia

40 mm dia

32 mm dia

25 mm dia

20 mm dia

UPVC Bend

65mm dia

50mm dia

40 mm dia

32 mm dia

25 mm dia

20 mm dia

UPVC Tee

65mm dia

50mm dia

40 mm dia

32 mm dia

25 mm dia

20 mm dia

UPVC Coupling

65mm dia

50mm dia

40 mm dia

32 mm dia

25 mm dia

20 mm dia

UPVC Reducer

50x40mm dia

25 x 20 mm dia

40 x 32 mm dia

32 x 25 mm dia

UPVC Reducer Elbow

50x40 mm dia

25 x 20 mm dia

40 x 32 mm dia

32 x 25 mm dia

UPVC Reducer Tee

50x40 mm dia

25 x 20 mm dia

40 x 32 mm dia

32 x 25 mm dia

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

65mm dia GM Gate Valve

50mm dia GM Gate Valve

40mm dia GM Gate Valve

32mm dia GM Gate Valve

25mm dia GM Gate Valve

20mm dia GM Gate Valve

supplying and fixing of pressure reduction valve for UPVC pipe lines . complete complying with standard specifications and should be got approved by the Executive Engineer before use on works

Supplying and fixing in position 150 x 100mm "P" or "S" stoneware gully trap 'A' grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three sand and Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works.

Supplying and fixing position CI Nahani Trap of size 100x75mm with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position best quality and approved make Indian made White glazed earthernware wash hand basin of size 550 x 400mm (without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coats of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position White glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using

Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position best variety and approved quality heavy type 15mm dia tap following type including cost for cutting and threading of the galvanised iron pipes cotton thread shellac etc. complete complying with standard specification.

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to be laid below ground level

230mm dia PVC soil / waste pipe

160mm dia PVC soil / waste pipe

110mm dia PVC soil / waste pipe

75mm dia PVC soil / waste pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

PVC Tee

160 mm dia

110 mm dia

75 mm dia

PVC Tee with door

160 mm dia

110 mm dia

75 mm dia

PVC bend

160mm dia

110mm dia

75 mm dia

PVC Elbow

160 mm dia

110mm dia

75 mm dia

PVC Elbow with door

160 mm dia

110mm dia

75 mm dia

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC Fibre Glass framed 600x450x5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks).

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The towel rail should be got approved by Executive Engineer before use on works).

Supplying and fixing best approved best quality brass CP soap tray of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supplying and fixing in position GI unions of heavy duty of approved quality and good variety of various sizes inluding necessary cutting and threading of GI pipes for jointing the union and providing two coats of painting with good variety and approved quality of synthetic enamel paint over one coat of primer in case of pipe line above ground level / one coat of tar in case of below ground level for both internal and external water supply arrangements, etc., complete complying with standard specifications. (The GI unions should be got approved by Executive Engineer before use on works).

50mm dia

40mm dia

32mm dia

25 mm dia

Supplying and fixing in position PVC cowls of following dia of best approved quality conforming to BIS, etc., complete complying with standard specifications. (The PVC cowl should be got approved by the Executive Engineer before use on works).

160mm dia

75mm dia

110mm dia

Supplying of Quartzite sink of overall size 533 x 457 mm and bowl size 469 x 392 x 205 mm made of pigmented Quartz acrylic granular material with matt finish. The Sink bottom (horizontal) surface finished with a thickness of 9-10mm and Sink sides (vertical) surface with a thickness of 7mm.The bottom provided with gentle slope with channelled grooves optimized drainage with waste coupling including conveying the material to the site etc., as directed by the departmental officers.

Providing and fixing Stainless Steel health faucet rate is including the cost of materials, labour etc., complete as directed by the departmental officers.

Supplying and fixing in position CP Head shower of approved make such as jaquar or equivalent with CP stop cock arrangement of size 15mm dia inlet and 100mm outlet to the pipe line with necessary cutting, threading and jointing using shellac etc., complete complying with standard specification and as directed by the departmental officers (The CP shower rose should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position CP Wall Mixture of approved make such as jaquar or equivalent with CP stop cock arrangement of size 15mm dia inlet and outlet to the pipe line with necessary cutting, threading and jointing using shellac etc., complete complying with standard specification and as directed by the departmental officers (The CP shower Wall Mixture should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position CP Shower arm of 300mm length of approved make such as jaquar or equivalent with CP stop cock arrangement of size 15mm dia inlet and outlet to the pipe line with necessary cutting, threading and jointing using shellac etc., complete complying with standard specification and as directed by the departmental officers (The CP shower arm should be got approved by the Executive Engineer before use on works).

Providing Anti-termite treatment to soil adjacent and under building foundation, plinth periphery of the building by application of chemicals of IS 6313 Part I to IV in stages to suit the progress of work as per the detailed specification as below. (Measurements taken for the plinth area for the purpose of payment) including breaking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing, etc., complete and as directed by the departmental officers. (The chemical should be got approved by Executive Engineer before use on work).

Stage-1: Spraying anti-termite chemical solution for the foundation before laying concrete, in bottom and sides of foundation.

Stage-2: Spraying anti-termite chemical solution to the grade beam level, spraying has to done for the grade beam, brick masonry contact with the back fill earth.

Stage-3: Spraying anti-termite chemical solution on the sand for the flooring before laying the flooring concrete. This treatment has to be carried out on the sand filling by making holes with crow bar to a depth of 60cms and at 60cms intervals on both direction and at junction of wall and flooring thoroughout.

Stage-4: Spraying anti-termite chemical solution alround building outside by making holes through bar before laying plinth protection and the holes to be closed after the treatment

Providing rain water arrangements by earthwork excavation in loose or hard soil to a depth of 90 cm and 100cm diameter and filled with 40 mm brick jelly to full depth and RCC well rings of 90 cm dia to adepth of 1.20 m and covering the top with precast slab of 75mm thick etc. complete

Sinking well in hard stiff clay, light black cotton soil, hard red earth , shales murram, gravel stoney earth , and earth mixed with small size boulders and hard gravelly soil including boiling or pumping charges if necessary etc., complete.

Brick work in Cement Mortar 1:5 (One Cement and five Sand) using best quality II class ground moulded chamber burnt bricks of size 9" x 4-3/8" x 2-3/4" including neat finishing, curing, etc., complete complying with standard specification.

Cement Mortar 1:5

foundation and basement

Above 1.50m depth upto 4.50m level

above 4.50m depth upto 9m level

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of 50mm thickness 300mm depth of following dia in RCC 1:2:4 (one cement, two sand and four aggregates), using 20mm HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed by the departmental officers.

Fire Fighting Arrangements

Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm –dia with oblique type instantaneous coupling with rotating wheel to open and close the valve including MS flange of table “E” , bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building as directed by the department officers.

Supply, and fixing in position of Fire fighting application Hose of 63mm dia of 15mts length binded by copper wire with 63mm dia Stainless steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the department officers Near every hydrant points.

Supply, and fixing in position of Fire fighting application 63mm dia stainless steel short length Branch Pipe with hexagonal type spray nozzle of 15mm (or) 20mm jet bore. Near every hydrant points.

Supply of Fire fighting application M.S. Hose Box so that to keep two numbers of Hose and one number of branch pipe with nozzle. It will have proper glass window type double door with universe open key, painted inside white and outside PO red. Near every hydrant point.

Supply, installation of Fire Fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary., etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT

Supply, erection, testing and commissioning of MS ‘C’ Class heavy pipe as per IS 1239, to with stand a developing pressure of 10 kg/Sq.cm including necessary fittings like MS flange of table ‘E’, Elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding. Including one coat metal primer and two coat p.o red painting. as directed by department officers.

150mm dia

100 mm dia

80 mm dia

65mm dia

50 mm dia

40mm dia

32mm dia

25mm dia

Wrapping and coating anti-corrosive treatment for under ground MS pipe as per standard method of one coat metal primer, one coat Bitumen and tar felt over coating, as directed by the departmental officers.

150 mm dia pipe

100mm dia pipe

Supply, erection, testing and commissioning of 150 mm dia heavy duty foot valve including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc., installed at end of 150 mm dia suction pipeline at sump as per the standard method and as directed by the departmental officers.

Supply, erection, testing and commissioning of 100 mm dia heavy duty foot valve including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc., installed at end of 100 mm dia suction pipeline at sump as per the standard method and as directed by the departmental officers.

Supply, erection, testing and commissioning of 80 mm dia heavy duty foot valve including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc., installed at end of 80 mm dia suction pipeline at sump as per the standard method and as directed by the departmental officers.

Supply, erection, testing and commissioning of Cast iron body Butterfly Valve of following sizes at required places to control the flow of water including necessary MS flange of table ‘E’, gaskets, bolts & nuts and as directed by the departmental officers.

150 mm dia

100 mm dia

80 mm dia

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Non-return valve of following sizes to control one way flow of water. To be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312 and as directed by the department officers.

150 mm dia

80 mm dia

100mm dia

Supply, erection, testing and commissioning of Gun metal Gate valve of size 50mm dia size including necessary MS flange of table ‘E’, gaskets, bolts & nuts etc., installed at pump house delivery line for the purpose of priming water to suction line as directed by the department officers.

Supply, erection, testing and commissioning of Gun metal non-return valve of size 50mm dia size including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc., installed at pump house delivery line for the purpose of priming to suction line so that to control one way as directed by the department officers.

Supply and providing 1000 Ltrs capacity priming tank made up of PVC(Sintex Make) mounted over the supporting arrangement fabricated using MS angle for the height of 3.00 mtrs from the floor level, inlet,outlet, and drian arrangements in fire fighting pump room as directed by the department officers.

Supply and laying of following sizes of armoured Aluminium/Copper cables for electrical motor, control panel, pressure switch jockey motor, etc., of any reputed make and as directed by the departmental officers

3 core 95 sq.mm. armoured aluminium cable

3 core 10 sq.mm. armoured aluminium cable

10 core 2.5 sq.mm. armoured aluminium cable

Supply and laying of 2 core 1.5 sq.mm. armoured copper cable for control wiring to the Terrace Pump Motor with runs of 14 SWG TC wire for earthing, providing in wall with suitable size GI clamps, screws, wooden plug, end termination by using suitable size cable glands, copper sockets and etc., as directed by the Departmental Officers.

Earthing arrangements with GI earth plate including charcoal and salt with necessary excavation and masonry work as per the standard method as directed by the department officers.

Supply, erection, testing and commissioning of (0 to 14kg), range Pressure Gauge of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure as directed by the department officers.

Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make line indfos or Donfos including necessary valves, couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start & auto stop the electrical motor, jockey motor as directed by the department officers.

Supply, erection, testing and commissioning of Fire Fighting Application Horizontal Centrifugal Type Pump Rated for 2280 LPM at 70 metres head with Electrical Motor of 60 HP of 415 volt 3 phase connection complete with base plate and accessories. (Make: Kirloskar or Equivalent). The rate inclusive of necessary vibration, bad mounting etc., as per standard method as directed by the Deparmental Officers.

Supply, erection, testing and commissioning Mono Block type Fire Fighting Pressurisation Pump of 180 LPM 110metres head at 10HP with suitable base frame including necessary vibration bad mounting etc., including conveying, fixing and incidental charges., etc., complete as per standard specification and as directed by the Departmental Officers. (Make: Kirloskar / Equivalent)

Supply, erection, testing and commissioning of Fire fighting 4 way fire brigade inlet with necessary Gun metal 63 mm dia non return spring shutter arrangements so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry , as directed by the department officers.

Supply, erection, testing and commissioning of Air release valve of 20mm dia so as to release airlock in 100mm dia MS pipe at top most wet riser, as directed by the department officers.

Supply and fixing of ABC(stored pressure type) 6kgs capacity Fire Extinguisher as per New IS No. 15683, complete with chemical powder, co2 Gas cartridge, Gun metal cap, squeeze grip with nozzle, wall mounting bracket, safety clip etc., as directed by the departmental officers.

Supply and fixing of carbon-di-oxide Gas type 2 kg capacity Fire Extinguisher as per New IS No. 15683 complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., as directed by the departmental officers.

Providing, fixing pipe supports from columns / wall or suspenders from roof slab to suit various dia of pipes made out of GI / MS adjustable rods threaded for a sufficient length to adjust the height of support along with clamping arrangement for holding pipes of anchor fastening, arrangement design of hanger and should confirm with specification.100mm

Supply, erection, testing and commissioning of cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water including necessary MS flange of table „E‟, gaskets, bolts & nuts including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT

150mm dia

100mm dia pipe

80mm dia

Supply, installation, testing and commissioning of Diesel Engine Driven Main Fire Pump suitable for automatic operation and consisting of following and complete in all respects as required. a. End suction, top discharge centrifugal pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg. / sq. cm at highest and farthest outlet at specified flow of 2280 LPM at 88m head conforming to IS 1520. b. 97 BHP, 2300 RPM water cooled with radiator, diesel engine conforming to relevant BS & IS standard complete. Auto starting mechanism, 12 volts / 24 volts electric starting equipment like self motor, dyanamo, solenoid switches etc. c. 110 litres capacity diesel tank mounted over stand fabricated using 25mm x 25mm x 6mm size MS angle, providing with level indicator, inlet port, outlet port, drain port and diesel return line port and fuel pre-filter, after filter etc. (Make: Kirloskar / Equivalent).

d.Exhaust system having flexible metallic mufler, 100mm dia MS heavy pipe extended upto 1m, outside pump house duly insulated with 50mm thick glass wool with 1mm thick aluminium sheet cladding, residential silencer with necessory MS support arrangements from wall or ceiling as per site condition.e. Dash board consisting the instruments like temperature gauge, galvano type DC Ammeter, lubricant oil pressure gauge, ignition switch, emergency stop and all other protection equipment as per specification, stop seleneid for auto stop in the event of fault with audio indications, painted with post office red colour etc., as required. f. 12 V / 24 V storage battery, maintenance free tape, 180 AH rating, MS fabricated common base plate, coupling guard, foundation bolts etc., as required. g. Positioning the diesel engine driven fire pump over cement concrete foundation using suitable size anti-vibration mounting arrangement. All works carried out as per standard methods and as instructed by the manufacturer and as directed by the Departmental Officers. (Make: Kirloskar / Equivalent)

Supply, erection, testing and commissioning of fire fighting application monoblock motor pumpset of 900 LPM at 40 metres head to develop 3.5 kg/sq.cm at the heightest and farthest hydrant point to make 30 m water jet at the time of fire fighting emergency cicumstances, coupled with 11 KW / 15 HP rated three phase 414 volts, 50 Hz, 2880 rpm electrical motor the pump with cast ron body, bronze impeller, rope gland packaging, suction size of 80 mm dia. delivery size of 65 mm dia., including the cost of foundaton concrete anti vibration mounting, rain safety hood and etc. complete as directed by the Departmental Officers (Kirloskar make KDS 1555+ or Equivalent)

Supply and laying of 4 core 10 sq.mm. armoured copper cable for power wiring to the Terrace Pump Motor with runs of 14 SWG TC wire for earthing, providing in wall with suitable size GI clamps, screws, wooden plug, end termination by using suitable size cable glands, copper sockets and etc., as directed by the Departmental Officers.

Supply & Installing of HI Tech Support for pipes with necessary Hitech rod, Anchor fastner, and U Clamp complying with standard specifications and as directed by the departmental officers

Supply and fixing nominal bore quartized bulb type sprinkler bulb 68 Deg C fast response pendent type including GI collar for each sprinkler bulb, mounted in MS pipe line using suitable size MS threaded coupling, thread, shellac etc., as per standard methods and including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply and fixing nominal bore quartized bulb type sprinkler bulb 68 Deg C fast response Sidewall type including GI collar for each sprinkler bulb, mounted in MS pipe line using suitable size MS threaded coupling, thread, shellac etc., as per standard methods and including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, installation, testing and commissioning of Micro Processor based conventional 8 Zone Fire Alarm Control Panel having the rating of 24 volt DC power supply, consisting 230 / 24 volt SMPS unit, 2 Nos. of 12 volt 7 AH standby batteries, suitably mounted on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers

Supply, installation, testing and commissioning of Manual Call Point (MCP) providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers. (Make: Ravel / Equivalent)

Supply, installation, testing and commissioning of Electronic Hooter / Sounder providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers (Make: Ravel / Equivalent)

supply and instalation of Public Addressable Wall Mounting Speaker 15w at the required points in the building complying with standard specifications and as directed by the departmental officers

supply and instalation of PA Mixer Amplifier 120W at the required points in the building complying with standard specifications and as directed by the departmental officers

Supplying, installing, testing and commissioning of Hand Held Mic complying with standard specifications and as directed by the departmental officers

Supply & Installation of in position the sign board of "EXIT " with arraow to be placed at walking pathways by fixing on walls to direct occupants to outside the buliding in an emergency. The Exit sign board will be autoglow photoluminiscent type which will glow at dark.(Single Side indication)

Supply & Installation of Fire Escape Route Plan Laminated Board Auto Glow Print to be placed at each floor by fixing on walls to direct occupants to outside the buliding in an emergency. The Fire Escape Route Plan will be autoglow photoluminiscent type which will glow at dark.(Single Side indication)

Supplyimg, fabricating and ercting and fixing Hilux board plain sheets of 10mm thick complete complying with standard specification and as directed by the departmental officers.

Construction of Inspection chamber or manhole of the following size including necessary earth work excavation in all soils to full depth as may be directed with sand filling at bottom of the chamber for 10cm thick, concreting CC 1:5:10 using 40 mm guage HBGs jelly 10 cm thick and sode walls 9" thick brick work in cement mortar 1:5 using II class chamber burnt bricks of size 9" x 43/8" x 23/4" filling the size of foundation with excavated earth, plastering with cm 1:3 20m thick for inside and bottom and making necessary benching with brick jelly cement concrete to the required slope and finishing neatly etc., complete.

Inspection Chamber of size 60Cm x 60Cmx 60 Cm(Avg)

Inspection Chamber of size 75Cm x 75 Cmx 90 Cm (Avg)

Inspection Chamber of size 90 Cm x 90 Cmx 150 Cm (Avg)

Inspection Chamber of size 120 Cm x 120 Cmx 210 Cm (Avg)

Supplying and fixing in position SFRC manhole covers with SFRC frames (Heavy duty) of following sizes of best approved quality as per standard specification etc., complete compying with standard specifications

Size of 60x60cm

Size of 75x75cm

Size of 90x90cm

Size of 120x120cm

Supplying and erecting multistage open well submerssible pumpset of 15HP capacity with 50mm delivery pipe suitable for open well / sump driven by 3 phase power supply with necessary tying rope and bed arrangements. The rate inclusive of supply and erecting star-delta starter with suitable underwater cable from starter to motor.

Supplying and erecting multistage open well submerssible pumpset of 10HP capacity with 50mm delivery pipe suitable for open well / sump driven by 3 phase power supply with necessary tying rope and bed arrangements. The rate inclusive of supply and erecting star-delta starter with suitable underwater cable from starter to motor.

Supply and erection of Double Leaves Fire Rated Door with Frame having the dimension of 1800mm x 700mm with following specifications.A.Door Frame 1.6mm: Galvanized 120 GSM branded make JSW b.Door leaf 1mm: Galvanized 120 GSM branded make JSW c.Shutter Thickness: 46mm d.Honeycomb: In-fill e.Glue Macroplast UR-7221 f.Door Hinges: 4" x 3" x 3mm, Double Ball: Make Assa Abloy Yale Ball bearing Butt Hinges Grade SS304 - Finish SS g.Door Closer with Standard Arm Finish:Silver h.Lock Set: Dead Lock with both side key i.Door Orientation: To be confirmed by client j. Mounting of door: Brick wall mounted k. Powder Coating : Powder coated in standard RAL paint colour of PO Red (60 to 90) Microns l.Single Point Panic Bar (2 Horizontal): Make Assa Abloy Yale or Equivalent m. Dead Lock with both side key: Make Assa Abloy Yale or Equivalent n.Vision Panel 200 x 300mm 2 Hrs. Fire Glass Schott Pyran with Frame 0.Rated Glass Schott Pyran with Frame p.Anchor Bolt with Endcaps The above assembly mounted on concrete or brick wall including the cost of cutting, chipping, concrete packing, plastering, scaffolding all other conveyance as per standard methods and as directed by the Departmental Officers.

Providing two legged scaffolding using 48.30mm outer diameter heavy duty M.S pipes over all height 3.00m the distance between two legs being 1.25m and the spacing of the post being 2.00m in each rows and providing platform with country wood plants using 40mm thick silver oak and 1.00 m wide in complete from with horizontal bracing @ 1.50 c/c vertical direction and with cross bracing using same 48.30mm diameter including cutting, threading assembly with one coat red oxide primer. Labour charges cost of special such on large plate, shoe, catcher, coupling, bolt and nut transport charges and handling charges. The bottom of vertical post shall rest on 300 x 300 x 70mm, 1:2:4 concreter base as per the standard specification.

Upto a height of 3.00 m

Above height of 3.00 m

External Hydrant Ring Main Excavation for laying M.S. Pipe in below ground with 0.60 x 1.20 meters width & depth and backfilling of soils including redoing of floors to the original condition as directed by the department officers.

Supply and fixing of 750 G.S.M. Tensile Canopy with complete fixtures. Application of 1 coat of MRF Epoxy SPEP - primer grey followed by two coats of MRF spectra polyurethane enamel top coat matching of IS-800. With necessary G.I. high tensile P.V.C. coated rope, M.S. powder coated cleat will be used as fixtures as per the standard specification and as directed by the Departmental Officers.

Supply and Fixing Aluminium Powder Coated Duct Louver 63 x 39 x1.5mm Aluminium Box Section, 115mm Aluminium Louver Section,Glazing Plate, and Screws to fix vertically at the top and bottom and vertically to the slab in complete compliance with standard specifications as directed by the department officer.

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil).

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil).

Supply and runof 2 of 1.5sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade inrigid pipe concealed in wall and ceiling with continuous earth wire connection of 1.5sq.mm copperwire and making good of the concealed portion with suitable colour.

Supply and run of 2 of 6sq.mm.PVC insulated SC unsheathed FRLS copper conductor of 1100V grade insuitable PVC rigid pipe on wall and ceiling with continuous earthwire connection of 6sq.mm copperwire with painting of suitable colour.

Supply and run of 2 of 4sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade insuitable PVC rigidpipe concealed in wall and ceiling with continuous earth wire connection of 4sq.mm copperwire and making good of the concealed portion with suitable colour.

Supply and run of 4 of 6sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 6sq.mm copper wire and making good of the concealed portion with suitable colour.

Supply and fixing of 20W, 4 feet LED tube on a SBT fitting on wall or ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of BH with 9W LED lamp with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of WT bulk head fitting with guard suitable for 11W CFL lamp (K- lite / Philips / Bajaj / Crompton/Equ.) for Lift Well.

Supply and fixing of 3 mod light lamp with unsheathed copper leads from terminals to the fitting.

supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting.

Supply and fixing of 65 mm 2 1/2 GI Pipe (Class – B) of 6 Mtr length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting of masonry pedestal with suitable MS box to house 6A SP MCB with suitable angle iron frame work, with door and with lock and key arrangements and supply and fixing of 80W LED Street light fitting with necessary clamps, on the above post with PVC unsheathed leads with painting of suitable colour.

Supply and fixing of AC/DC 76 mm Buzzer / Call Suitable for 230 V 50 C/S Single phase AC supply on suitable TW board with push switch.

Supply and fixing of 1200 mm (48”) AC Ceiling fan High Speed (Crompton / Havells / Usha/ Eq ) Complete with 2 module 100W fan step regulator (Lower end) with 300 mm down rod with fan clamp with side plates and cross arm of size 450 mm (18").

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete without provision of hole in the wall.

Supply and fixing of louvers shutter arrangements for 300 mm (12”) sweep (light duty) AC Exhaust fan.

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI) in flush with wall with connections.

Supply and fixing of 1 no.6/16 A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box ( GI ) in flush with wall with connections.

Supply and fixing of 3nos.6A two module socket , 1 no. 6/16A two module socket , 3 nos. 6A one module switch, 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI) in flush with wall with connections.

Supply and fixing of 25A Flush type Wall Socket 25A DP MCB complete set for AC Plug in flush with wall with earth connection (For AC Plug).

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 40A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only.

Supply and fixing of 7 segment 4 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 4 ways in each segment) and seperate provision for MCB / Isolators ( totally 12 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush wall with earth connection only.

Supply and Fixing of Horizontal type 4 way triple pole neutral MCB distribution board with Metal Door cover with IP42 Protection, with 63A 4 pole MCB as incoming and 12 nos 6A – 32A SPMCB outgoing on suitable angle iron frame work with earth connection only. The MCB DB and MCB’s should be with ISI mark (Like Legrand / Hager/ eq.).

Supply and Laying of 3 1/2 x 240 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (Main Pillar to consumer piller)

Supply and Laying of 3 1/2 x 120 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (Consumer Pillar to metering panel board and generator)

Design, Supply, Erection, Testing and Commissioning of Free standing Floor mounting CPRI certified Indoor panel board made up of 2mm thickness powder coated CRCA sheet steel with Siemens grey paint. The panel should comprising of (i) Incomer - 400A TPN 35kA MCCB with Thermal and Magnetic Release with front operated handle and R Y B indications , ON/OFF/Trip indications,HRC fuse carriers for control wiring and toggle Switches, Digital Voltmeter and Ammeter with required 400A CT (ii) Out going - 12 Nos of individual 3 phase Metering provision with see through glass , 12 nos of individual 63A TPN MCB & 12 Nos of individual Neutral Link, and Double Side Panel Earthing with 25 x 3mm Cu earthing, 10 sq mm Single stand copper Wires for inter Connection of all services as per TNEB Standard and (iii) the bus bar chamber should be with 50x6mm cu bus bar for 3 Phases and Neutral and 25 x 3 mm cu bus for earth in a bus bar chamber.

Supply and fixing of 200 A Three phase 500V 4 Pole Change over Switch on suitable angle iron frame work with MS cable entry boxes with PWD earthing.

Supply and fixing of Vertical type 4 way triple pole neutral MCB distribution board with Metal/Acrylic Door cover with IP42 Protection, with 1 No 100A 4 pole MCB as incoming 2 Nos 63A TPMCB and 6 nos 32A SPMCB as Outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB’s should be with ISI mark.(Like Legrand /Hager L &T make/eq.).

Supply and fixing of Vertical type 8way triple pole neutral MCB distribution board with Metal/Acrylic Door cover with IP42 Protection, with 1 No 125A 4 pole MCCB as incoming 5 Nos 100A TPMCB Isolator and 9 nos 32A SPMCB as Outgoing in flush with wall and making good of the concealed portion with earth connection only.The MCB DB and MCB’s should be with ISI mark.(Like Legrand /Hager L &T make/Equ.) (Common)

Supply and Laying of 3 1/2 x 35 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (For Motor).

Supply and Laying of 4 x 10 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (For Street Light).

Supply and fixing of brass cable gland for 3 ½ x 240 Sqmm PVC armoured LTUG cable with earth connection.

Supply and fixing of brass cable gland for 3 ½ x 120 Sqmm PVC armoured LTUG cable with earth connection.

Supply and fixing of brass cable gland for 3 ½ x 35 Sqmm PVC armoured LTUG cable with earth connection.

Supply and fixing of brass cable gland for 4 x 10 Sqmm PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 3 ½ x 240 Sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete.

Supply and providing cable end termination of 3 ½ x 120 Sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete.

Supply and providing cable end termination of 3 ½ x 35 Sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete.

Earthing as per ISI specification with an earth electrode of 2.1 Mt. class ‘B’ GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and run of No.8 SWG Copper wire for earth connection (For Lift).

Supply and run of No.8 SWG GI wire for earth connection.

Supply installation testing and commissioning of aviation obstruction light , single -lamp type with red omni-directional steady glow , based on LED technology , complete with Photovoltaic -ON/OFF control, earthing lead , wiring to power source up to 5 m away drawn through metallic conduit all complete as per specifications, drawings and or as directed by the Engineer In Charge.

Supply, Erection, Testing, Commissioning and Handing over of 1 No Gearless with machine room 13 Persons Capacity Passenger and differently abled persons Lift as per following technical specifications including all taxes and duties. Technical Specifications: 1. Location: New ‘C’ type PWD quarters Saidapet, Chennai. 2. No of Lift: One No. 3. Type of Lift: Passenger 4. Capacity of Lift : 13 Persons Passenger (884 Kgs) 5. Speed: 1.6 mtr /Sec 6. Type of Drive: Microprocessor based specific variable voltage variable frequency V3F Drive with enhanced ride comfort and near zero leveling functions. 7. No of floor: Ground + 16 floors.

8. Total Travel: 60 Mtrs Approximate. 9. Leveling Accuracy: High level accuracy with smooth & jerk free stopping. 10. Construction of car: Special car made of Stainless Steel Hairline finish & panels with direct lighting and new beautiful single tile false ceiling with tubular handrail and mirror. 11. Position of Machine: Directly above the lift well. 12. No. of Landing Entrance: One in front 20 Nos only. 13. No. of Car Entrance: One in front only. 14. Car Entrance Door: Automatic Centre opening door with steel painted finish with full length infra red sensor for better safety. 15. Landing Entrance Door: Automatic centre opening door with steel painted finish with emergency opening device. 16. Lift well: 2550mm (width) x1950mm (depth) (required as per IS14665 = 2500X1900) available size. 17. Lift pit depth available: 1750mm 18. Car size: 1100 mm wide x 2000mm deep (Part I) – 2200). 19. Car clear Opening: 900mm x 2000 mm (as per IS 14665 (Part-I) – 2000).

20. Lift Machine Room: As per standard specification. 21. Power Supply: 415v, 3 phases, 50 C /Sec A.C supply for power and 230 V, 50 Hz single phase AC supply for light. 22. Control: Microprocessor Computer based – simplex collective full collective logic system with/without attendant mode. 23. Car fittings: Compact fluorescent lighting with 1 nos 300 mm sweep cabin fan. 24. Lift Well: RCC construction with Brick masonry. 25. Indication: Up/Down Digital Direction scroll type and position indicator for all landing and in car.26. Emergency Alarm Bell: Battery Operated Alarm Bell to be provided with automatic charging device. 27. Emergency Light: Battery operated Light to be provided with automatic Charging device. 28. Fireman’s switch: To be provided at ground floor.

29.Minor Builders Work: To be provided By Lift contractor. 31. Stainless Steel sill angles and facia Plates: To be provided by lift contractor. 32. Steel for lift Machinery: To be Provided by lift contractor. 33. Servicing and Maintenance: Free Comprehensive servicing and maintenance should be provided by lift contractor during the guarantee period of one year. 34. Provision of intercom with phone to be provided by lift contractor. 35. Lift License: Preparation of drawing, Payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate and lift license as per lift act should be done by lift contractor.

36. Automatic rescue device – To facilitate the landing of the nearest floor at the time of power failure. This shall consist of suitable type battery system with charges inverter, under voltage protection system etc. 37. Floor annunciation system with music.

38. Special futures: (a). Infra red door sensor withFull height screen. (b). Full width half height rear panel Mirror. (c).Voltage stabilizer for circuit control. (d). Tubular Stainless Steel hand rail in car (e). Signal Fixtures (f). Vandal proof S.S. button with S.S. cover. (g). Stainless steel door frames (h). V3F door operator (i) Call register signal (j) Pit ladder (k). Braille buttons (l).Stainless steel facia for car operating panel and landing fixtures. (m). ON-OFF switch for fan and Light. (n) Over load warning indicator. 39. Over speed governor, phase failure and phase reversal relay, alarm bell, Guide brackets for car and counter weight, rubber padding under winding unit, Motor of adequate capacity, single reduction worm gear, electromagnetic brake with compression springs, car safety gears, buffer, electro mechanical door locks, emergency key, side supporting angles, motor over load protection devices, final limit switch, main suspension ropes, counter weights, lifting joint joist for mounting the machineries.

40. Guarantee: Guarantee for the Materials& workmanship of equipment’s complete should be offered by the Lift firm for a period of not less than one year. 41. 41. Site testing in accordance with IS 14665 42. should be carried out at the time of ( make, Johnson/kone/OTIS/ eq.)

Supply, Erection, Testing, Commissioning and Handing over of 1 No Gearless with machine room 20 Persons Capacity Passengernd differently abled persons Lift as per following technical specifications including all taxes and duties. Technical Specifications: 1.Location: New ‘C’ type PWD quarters Saidapet, Chennai 2. No of Lift: One No. 3. Type of Lift: Passenger 4 .Capacity of Lift : 20 Persons Passenger (1360 Kgs) 5 .Speed: 1.6 mtr /Sec 6.Type of Drive: Microprocessor based specific variable voltage variable frequency V3F Drive with enhanced ride comfort And near zero leveling functions. 7. No of floor: Ground + 16 floors. 8 .Total Travel: 60 Mtrs Approximate. 9 Leveling Accuracy: High level accuracy With smooth & jerk free stopping. 10 Construction of car: Special car made of Stainless Steel Hairline finish & panels with direct lighting and new beautiful single tile false ceiling with tubular Handrail and mirror.

11.Position of Machine: Directly above The lift well. 12. No. of Landing Entrance: One in front 20 Nos only. 13. No. of Car Entrance: One in front only. 14. Car Entrance Door: Automatic Centre opening door with steel painted finish with full length infra-red sensor for better safety. 15 Landing Entrance Door: Automatic centre opening door with steel painted finish with emergency opening device. 16 Lift well: 2400mm (width) x3000mm (depth) available size. ( required as per IS 14665 = 2500x2400mm) 17 Lift pit depth available: 1750mm 18 Car size: 2000mmx1500mm 19 Car clear Opening: 1000mm x 2000 mm (as per IS 14665 (Part-I) – 2000). 20 Lift Machine Room: As per standard specification. 21 Power Supply: 415v, 3 phase, 50 CY /Sec A.C supply for power and 230 V, 50 Hz single phase AC supply for light. 22 Control: Microprocessor Computer based – simplex collective full collective logic system with/without attendant mode. 23 Car fittings: Compact fluorescent lighting with 1 nos 300 mm sweep cabin fan.

24 Lift Well: RCC construction with Brick masonry. 25 Indication: Up/Down Digital Direction scroll type and position indicator for all landing and in car. 26 Emergency Alarm Bell: Battery Operated Alarm Bell to be provided with automatic charging device. 27 Emergency Light: Battery operated Light to be provided with automatic Charging device. 28 Fireman’s switch: To be provided at ground floor. 29.Minor Builders Work: To be provided By Lift contractor. 30.Scaffolding: To be provided by lift Contractor. 31. Stainless Steel sill angles and facia Plates: To be provided by lift contractor. 32 Steel for lift Machinery: To be Provided by lift contractor. 33. Servicing and Maintenance: Free Comprehensive servicing and maintenance should be provided by lift contractor during the guarantee period of one year. 34. Provision of intercom with phone to be provided by lift contractor.

35. Lift License: Preparation of drawing, Payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate and lift license as per lift act should be done by lift contractor. 36. Automatic rescue device – To facilitate the landing of the nearest floor at the time of power failure. This shall consist of suitable type battery system with charges inverter, under voltage protection system etc. 37. Floor annunciation system with music. 38. Special futures: (a). Infra-red door sensor with Full height screen. (b). Full width half height rear panel Mirror. (c).Voltage stabilizer for circuit control. (d). Tubular Stainless Steel hand rail in car (e). Signal Fixtures (f). Vandal proof S.S. button with S.S. cover. (g). Stainless steel door frames (h). V3F door operator (i) Call register signal (k) Pit ladder (k). Braille buttons (l).Stainless steel facia for car operating panel and landing fixtures. (m). ON-OFF switch for fan and Light. (n) Over load warning indicator.

39. Over speed governor, phase failure and phase reversal relay, alarm bell, Guide brackets for car and counter weight, rubber padding under winding unit, Motor of adequate capacity, single reduction worm gear, electromagnetic brake with compression springs, car safety gears, buffer, electro mechanical door locks, emergency key, side supporting angles, motor over load protection devices, final limit switch, main suspension ropes, counter weights, lifting joint joist for mounting the machineries.40. Guarantee: Guarantee for the Materials& workmanship of equipment’s complete should be offered by the Lift firm for a period of not less than one year. 41. Site testing in accordance with IS 14665 should be carried out at the time of Handing over. (make: Johnson/ kone/ OTIS / Eq)

Supply, erection, testing, commissioning and handing over of 1No 125 KVA Diesel Generator set of 0.8 P.F. Three Phase 415/420 Volts, 50 C/S, 1500 RPM as detailed below. 1. ENGINE Water cooled diesel engine suitable for Generator Application with a shaft output of 156 BHP at 1500 RPM under NTP condition as per BSS 5514/IS 10000. The Engine shall comprise the following Standard scope of supply. (Make:Kirloskar/Cummins/AshokLeyland/ Greaves) 1. Dry type Air cleaner 2. Expansion bellow 3. Radiator, Radiator fan and mounting 4. Air to Air charge cooler 5. Exhaust Gas turbo charger 6. Lube oil cooler and Lube oil filter 7. Fuel filter (pre and micro) 8. In-Line Mono-block fuel injection pump with governor fuel feed pump 9. Electronic governor 10. 24V Battery charging alternator 11. 24V Volt electric starter motor 12. Engine test certificate 13. Residential muffler. 14. Fly wheel with starter ring

ENGINE INSTRUMENT PANEL MOUNTED Engine control panel consisting of ON /OFF /START Key Lube oil pressure gauge, Oil Temp gauge, High water temperature gauge and electronic hour meter and RPM indicator. SAFETY SYSTEM OF ENGINE: The Engine shall trip for the following conditions with visual alarm device. 1. Low Lubricating Oil pressure High Water temperature Vee-belt failure and over speed, The visual indicator should also be provide for low battery indication.The Engine should be capable of providing 10% over load for one hour for every 11 hours continuous running at full load 2. ALTERNATOR: Alternator capacity of 125KVA/100 KW, AC 3 Phase, 50HZ,415Volts, 0.8 P.F. 4 wire self excited, self regulated designed to run at 1500 RPM under NTP conditions conforming to BS 5000 /IS 13364 (Part-II) 1992 to be coupled directly to the Diesel Engine and Test certificate. (Make: Kirloskar/ Crompton/ Greaves /Equivalent).

27. MCCB of 630 A capacity with magnetic thermal over lead release, instant short circuit trip and under voltage release switch 28. Rectangular copper bus bars (1 No for each phase, neutral and earthing terminal) of adequate capacity duly colour coded with heat shrinkable PVC sleeves. 29. 1 No Mains Voltage monitor 30. Hooter/ Audio Alarm for indication set fails to start and for DG O/L 31. 1 Set Timers 32. Audio and visual indication arrangements for a. Low Lubricating Oil pressure b. High water temperature c. Over speed 33. 1 No Earth fault relay 34. Isolator to Isolate the neutral NOTE: 1. The control panel should be complete with necessary fuses, cables, labels, other accessories with isolation arrangements. 2. The engine should trip for the following conditions a. Low Lubricating Oil pressure b. High water temperature c. Over speed

4.ACOUSTIC ENCLOSURE: Acoustic enclosure shall be powder coated and Fabricated of 16 SWG CRCA MS sheet. The silent canopy shall be of nut bolt type construction. Critical processes of punching are done on CNC Machines to maintain dimensional accuracy of hole within 0.1 mm. Powder coating done after seven-tank surface preparation process of sheet metal. Canopy panel and doors shall have inside lining of FIRE RETARDANT 64Kg/m density Mineral wool of 100mm Thickness as acoustic material. Four hinged doors shall be provided to canopy. The average sound level at 1Mt. distance shall be as per latest CPCB norms. Surface Treatment – Painting: The enclosure surface shall be suitably treated for degreasing de-rusting and posphating. The canopies are passed through seven- tank treatment thoroughly. Additional features of Canopies: Canopy fabricated on CNC machines with dimensional Accuracy of 0.1mm so as to increase its durability. Special designed supporting rips/ structures are used in canopies so as to be sturdy steadiness and to reduce the vibrations of the DG sets if any. World class Cooling Package:

35. Canopies shall have Cooling package for which it can also perform at 45˚ deg C/ ambient temperature No grouting required on the ground only a level surface capable of withstanding the DG weight. Lifting hooks shall be provided for the acoustic Enclosure, which should be unloaded independently of the DG Set. The Gen set frame shall also be provided with hooks for unloading. Temperature rise inside the canopy Canopies shall be designed so as to maintain the temperature difference between ambient and air inlet at cleaner within the enclosure well within 5-7 deg centigrade as per the latest norms. 5.FUEL TANK: 230 Ltrs. Removable fuel tanks shall be fabricated out of 14SWG CRCA MS sheet and is part of base frame. It is duty painted and fitted with inlet and outlet connections and mechanical fuel gauge. Fuel tank can be easily removed for clearing or any maintenance.

6.BASE FRAME: Base frame should be fabricated in sheet metal. The base frame is rugged in construction and designed for mounting engine and brush less alternator closely coupled with cross members mounted on AVM. The base frame shall be provision for mounting of acoustic enclosure on it. The supply of generator set includes loading unloading and transportation charges. 7.BATTERY: 2Nos 12V 180AHR Battery. 1. Preparation of site plant physical layout electrical line schematic diagram in 10sets, getting drawing approval from CEIG preparation completion report, rectification report and arranging CEIG inspection and obtaining CEIG safety certificate preparation of 2sets of approved drawing and a copy of safety certificate in a neat frame work to be fixed in generator room and payment of CEIG inspection fees for 125 KVA Genset.

Erection of Generator set: Erection, Testing, Commissioning and Handing over of the Generator set with suitable concrete foundation with cement concrete 1:2:4 with sand cushion all around the foundation erection of 125 KVA Generator set over the foundation and with proper alignment over the existing foundation and with proper alignment over the existing Foundation to suit 125 KVA Gen set. Including supply and fixing of ‘Dunlop’ make anti vibration mounts to the Generator set with initial supply of diesel.

Supply and installation of exhaust piping of sufficient length with suitable MS pipes so as to extend outside the generator room with necessary thermal insulation.

Preparation of Electrical Drawing and submitting the diagram, inspection fees for electrical inspectorate and getting CEIG approval with safety certificate.

Supplpy and erection of lightning arrestor/conductor made up of 2.5" dia electrolitic copper ball with 5 Nos. Spikes each 5" long 1" dia copper ROD of 1" thick 4' Long with suitbale base to be fixed on suitbale supporting structure with necessary heavy duty clamping arrangements n top wall supporter with mansonry pedestal to withstand wind pressure.

Supply and run of 50mm x 6mm GI Flat Down Conductor with necessary clamps / supports on wall / floor / ground for earth connection.

Supply and fixing of Epoxy Insulator suitbale for lightning conducor with bolts and nuts.

Supply and providing of Plate Earth electrode with 3mts of Class ' B ' GI pipe 40 mm and 3mm thick of copper plate of size 24" x 24" x 3 mm riveted to the pipe at one end and providing a funnel at the top end with 2runs of 25mm x 3mm copper flat from the copper plate to the top of the electrode and embedding the above electrode in a pit to be excavated at a depth of 3mt and of size 60cm x 60cm and filling up the pit with charcoal, salt, sand.

Supply and fixing of 6 mtr with solar light fitting with complete electrical connection.

Supply and fixing of 40A 4pole Residual Current Breaker with Overcurrent protection(L&T make)on existing DB with necessary connection.

Supply and fixing of 11KV, 630A, 21KA/3sec, 3way extensible, outdoor, motorized,RMU comprising of 2 isolators(LBS)& 1 circuit breaker(VCB), without FRTU & modem AEGIS type as per TANGEDCO specs (make:LUCY/Equ.)

GST at 18%

P and C Projects Private Limited (BID ID -1163297)

R.R.THULASI BUILDERS (INDIA) PRIVATE LIMITED (BID ID -1162930)