WBPWD/SSE/SWEC/NIQ59/2025-26

Amount

Part -A ( Solar Lighting work)

Stand Alone Solar PV Street Lighting System Supplying and fixing 6 mtr GI pole (Hot Dip Galvanized) of 3 mm thickness with metallic Ladder for maintenance(Tata/ Bansail /Utkarsh) Foundation Construction & Erection of suitable Shallow foundation upto 06 mtr. Octagonal Pole with M-20 grade concrete for Pole considering soil bearing capacity (SBC) 10T/sq. mtr. at 2 Mtr. depth with all materials and labour payment made as per PWD civil schedule & as per direction of EIC. Erection of Pole by using of lifting equipment like hydra etc. and fixing of foundation bolts , anchor plate etc.

Solar Panel SITC of 1 no 75 Wp Mono PERC PV module with IFC 61215, IEC 6173-1.2 compliance with any IS MNRE approved purpose of Luminaries and PV system(MAKE - PANASONIC/PHILIPS/ANSH SOLAR/WIPRO.) Solar Light SITC of 1 no 12 W Luminaries comprise of: a) 12 W LED with minimum coker temperature (CCT) 5500-6500%, mmmum typical luminous lux 100Lm/W ie minimum 1200Lm (MAKE- PANASONIC/PHILIPS/ANSH SOLAR/WIPRO) 5 YEARS COMPLETE CARE WARRANTY ON SITE. b) Charge controller with MPPT and efficiency 92% and it should have overcharge protection, deep discharge protection, Battery reverse polarity protection, Loud short circuit protection. Open circuit protection, Panel reverse polarity protection, Over temperature protection. c) Automatic dusk to drawn controlling system to monitor LED Operation d)With without dimmer arrangement.

Batteries SITC of 1 no 12. 8 V. 30 Ah LITHIUM FERRO PHOSPHATE (Li FeP04) Batteries having BIS certificate. The batteries should have battery maragenient system (BMS) with higher life expectancy, longer cycle life low discharge rate and fast charging facilities. Battery should provide 12 Hr buckup. The battery must be provided with GI out door type battery box Inbuilt in Luminaries(Make- Exside/ANSH SOLAR/Surya ) Battery must have 5 yers warranty period. Cables and wires a) DC cable 4 sqmm & control cable as per requirement

Stand Alone Solar PV Street Lighting System Supplying and fixing 7 mtr GI pole (Hot Dip Galvanized) of 3 mm thickness with metallic Ladder for maintenance (Tata/ Bansail /Utkarsh) Foundation Construction & Erection of suitable Shallow foundation upto 07 mtr. Octagonal Pole with M-20 grade concrete for Pole considering soil bearing capacity (SBC) 10T/sq. mtr. at 2 Mtr. depth with all materials and labour payment made as per PWD civil schedule & as per direction of EIC. Erection of Pole by using of lifting equipment like hydra etc. and fixing of foundation bolts , anchor plate etc.

Solar Panel SITC of 1 no 75 Wp Mono PERC PV module with IFC 61215, IEC 6173-1.2 compliance with any IS MNRE approved purpose of Luminaries and PV system(MAKE - PANASONIC//PHILIPS/ANSH SOLAR/WIPRO.) Solar Light SITC of 1 no 12 W Luminaries comprise of: a) 12 W LED with minimum coker temperature (CCT) 5500-6500%, mmmum typical luminous lux 100Lm/W ie minimum 1200Lm (MAKE- PANASONIC/PHILIPS/ANSH SOLAR/WIPRO) 5 YEARS COMPLETE CARE WARRANTY ON SITE. b) Charge controller with MPPT and efficiency 92% and it should have overcharge protection, deep discharge protection, Battery reverse polarity protection, Loud short circuit protection. Open circuit protection, Panel reverse polarity protection, Over temperature protection. c) Automatic dusk to drawn controlling system to monitor LED Operation d)With without dimmer arrangement.

Batteries SITC of 1 no 12. 8 V. 30 Ah LITHIUM FERRO PHOSPHATE (Li FeP04) Batteries having BIS certificate. The batteries should have battery maragenient system (BMS) with higher life expectancy, longer cycle life low discharge rate and fast charging facilities. Battery should provide 12 Hr buckup. The battery must be provided with GI out door type battery box Inbuilt in Luminaries(Make- Exside/ANSH SOLAR/Surya ) Battery must have 5 yers warranty period. Cables and wires a) DC cable 4 sqmm & control cable as per requirement

Stand Alone Solar PV Street Lighting System Supplying and fixing 6 mtr GI pole (Hot Dip Galvanized) of 3 mm thickness with metallic Ladder for maintenance (Tata/ Bansail /Utkarsh) Foundation Construction & Erection of suitable Shallow foundation upto 06 mtr. Octagonal Pole with M-20 grade concrete for Pole considering soil bearing capacity (SBC) 10T/sq. mtr. at 2 Mtr. depth with all materials and labour payment made as per PWD civil schedule & as per direction of EIC. Erection of Pole by using of lifting equipment like hydra etc. and fixing of foundation bolts , anchor plate etc.

Solar Panel SITC of 1 no 100 Wp Mono PERC PV module with IFC 61215, IEC 6173-1.2 compliance with any IS MNRE approved purpose of Luminaries and PV system (MAKE - PANASONIC/PHILIPS/ANSH SOLAR/WIPRO.) Solar Light SITC of 1 no 18 W Luminaries comprise of: a) 18 W LED with minimum coker temperature (CCT) 5500-6500%, mmmum typical luminous lux 100Lm/W ie minimum 1800Lm (MAKE- PANASONIC/PHILIPS/ANSH SOLAR/WIPRO) 5 YEARS COMPLETE CARE WARRANTY ON SITE. b) Charge controller with MPPT and efficiency 92% and it should have overcharge protection, deep discharge protection, Battery reverse polarity protection, Loud short circuit protection. Open circuit protection, Panel reverse polarity protection, Over temperature protection. c) Automatic dusk to drawn controlling system to monitor LED Operation d)With without dimmer arrangement.

Batteries SITC of 1 no 12. 8 V. 42 Ah LITHIUM FERRO PHOSPHATE (Li FeP04) Batteries having BIS certificate. The batteries should have battery maragenient system (BMS) with higher life expectancy, longer cycle life low discharge rate and fast charging facilities. Battery should provide 12 Hr buckup. The battery must be provided with GI out door type battery box Inbuilt in Luminaries(Make- Exside/ANSH SOLAR/Surya ) Battery must have 5 yers warranty period. Cables and wires a) DC cable 4 sqmm & control cable as per requirement

Stand Alone Solar PV Street Lighting System Supplying and fixing 7 mtr GI pole (Hot Dip Galvanized) of 3 mm thickness with metallic Ladder for maintenance (Tata/ Bansail /Utkarsh) Foundation Construction & Erection of suitable Shallow foundation upto 07 mtr. Octagonal Pole with M-20 grade concrete for Pole considering soil bearing capacity (SBC) 10T/sq. mtr. at 2 Mtr. depth with all materials and labour payment made as per PWD civil schedule & as per direction of EIC. Erection of Pole by using of lifting equipment like hydra etc. and fixing of foundation bolts , anchor plate etc.

Solar Panel SITC of 1 no 100 Wp Mono PERC PV module with IFC 61215, IEC 6173-1.2 compliance with any IS MNRE approved purpose of Luminaries and PV system (MAKE - PANASONIC/PHILIPS/ANSH SOLAR/WIPRO.) Solar Light SITC of 1 no 18 W Luminaries comprise of: a) 18 W LED with minimum coker temperature (CCT) 5500-6500%, mmmum typical luminous lux 100Lm/W ie minimum 1800Lm (MAKE- PANASONIC/PHILIPS/ANSH SOLAR/WIPRO) 5 YEARS COMPLETE CARE WARRANTY ON SITE. b) Charge controller with MPPT and efficiency 92% and it should have overcharge protection, deep discharge protection, Battery reverse polarity protection, Loud short circuit protection. Open circuit protection, Panel reverse polarity protection, Over temperature protection. c) Automatic dusk to drawn controlling system to monitor LED Operation d)With without dimmer arrangement.

Batteries SITC of 1 no 12. 8 V. 42 Ah LITHIUM FERRO PHOSPHATE (Li FeP04) Batteries having BIS certificate. The batteries should have battery maragenient system (BMS) with higher life expectancy, longer cycle life low discharge rate and fast charging facilities. Battery should provide 12 Hr buckup. The battery must be provided with GI out door type battery box Inbuilt in Luminaries(Make- Exside/ANSH SOLAR/Surya ) Battery must have 5 yers warranty period. Cables and wires a) DC cable 4 sqmm & control cable as per requirement

Stand Alone Solar PV Street Lighting System Supplying and fixing 06 mtr GI pole (Hot Dip Galvanized) of 3 mm thickness with metallic Ladder for maintenance (Tata/ Bansail /Utkarsh) Foundation Construction & Erection of suitable Shallow foundation upto 06 mtr. Octagonal Pole with M-20 grade concrete for Pole considering soil bearing capacity (SBC) 10T/sq. mtr. at 2 Mtr. depth with all materials and labour payment made as per PWD civil schedule & as per direction of EIC. Erection of Pole by using of lifting equipment like hydra etc. and fixing of foundation bolts , anchor plate etc.

Solar Panel SITC of 1 no 100 Wp Mono PERC PV module with IFC 61215, IEC 6173-1.2 compliance with any IS MNRE approved purpose of Luminaries and PV system (MAKE - PANASONIC/PHILIPS/ANSH SOLAR/WIPRO.) Solar Light SITC of 1 no 25 W Luminaries comprise of: a) 25 W LED with minimum coker temperature (CCT) 5500-6500%, mmmum typical luminous lux 100Lm/W ie minimum 2500Lm (MAKE- PANASONIC/PHILIPS/ANSH SOLAR/WIPRO) 5 YEARS COMPLETE CARE WARRANTY ON SITE. b) Charge controller with MPPT and efficiency 92% and it should have overcharge protection, deep discharge protection, Battery reverse polarity protection, Loud short circuit protection. Open circuit protection, Panel reverse polarity protection, Over temperature protection. c) Automatic dusk to drawn controlling system to monitor LED Operation d)With without dimmer arrangement.

Batteries SITC of 1 no 12. 8 V. 42 Ah LITHIUM FERRO PHOSPHATE (Li FeP04) Batteries having BIS certificate. The batteries should have battery maragenient system (BMS) with higher life expectancy, longer cycle life low discharge rate and fast charging facilities. Battery should provide 12 Hr buckup. The battery must be provided with GI out door type battery box Inbuilt in Luminaries(Make- Exside/ANSH SOLAR/Surya ) Battery must have 5 yers warranty period. Cables and wires a) DC cable 4 sqmm & control cable as per requirement

Supply & Delivery of 6 mtr. Galvanized Octagonal Pole, Top A/F 70, bottom A/F 130, Thickness 3 mm, Base Plate -200x200x12 Wind speed shall be considered 50m/s as per IS:875 and Supply of 4 No.M20X 600 “J” Type foundation bolts as per EN-B Grade manufactured from special steel along with nuts, washers, Anchor Plate, and templates A) Material Construction Shaft Equivalent to BSEN 10025 Or As per IS 2062 B) Materials grade of Base Plate shall be E250(BR)as per IS:2062 C) Galvanization as per IS 4759 [Make :- Surya/Transrail/Valmont/Utkarsh/Bajaj]

The pole foundation & erection (Civil work) Erection Octagonal pole of length as given below with /without sole place & cap etc in ordinary cement concrete (mix 1:2:4) with graded stone chips (20 mm) foundation of size 0.5m x 0.5m maximum round base block below sole plate /pole jhama metal incl. cc (1:3:6) upto 1 meter

Supply & Fixing of 30W solar All in one(Integrated) LED streetlight system, Solar PV panel: Mono Crystalline PV Panel 60WP, Solar Battery- 12.8V 30AH Lithum Ferrous Phosphate Battery with BMS BIS approved, Led Street light -30W with high lumen efficasy >135 lm/w , Housing - Aluminum, Charge controller-MPPT Intergral charge controller (Inbuild in to the street light) CCT-6000-6500K, IP65, Dimming facility available. [Make- PANASONIC/PHILIPS/ WIPRO/Ansh Solar]

Repairing of Solar Light as per site requirement incl. Solar Panel,Batteries , Light etc

Repairing of Solar Light as per site requirement incl. Solar Panel,Batteries , Light etc

Repairing of Solar Light as per site requirement incl. Solar Panel,Batteries , Light etc

Part- B ( Street Lighting Work)

Supply & Delivary of 6 mtr. Galvanized Octagonal Pole, Top A/F 70, bottom A/F 130, Thickness 3 mm, Base Plate -200x200x12 Wind speed shall be considered 50m/s as per IS:875 and Supply of 4 No.M20X 600 “J” Type foundation bolts as per EN-B Grade manufactured from special steel along with nuts, washers, Anchor Plate, and templates A) Material Construction Shaft Equivalent to BSEN 10025 Or As per IS 2062 B) Materials grade of Base Plate shall be E250(BR)as per IS:2062 C) Galvanization as per IS 4759 [Make :- Surya/Transrail/Valmont/Utkarsh/Bajaj]

The pole foundation & erection (Civil work) Erection Octagonal pole of length as given below with /without sole place & cap etc in ordinary cement concrete (mix 1:2:4) with graded stone chips (20 mm) foundation of size 0.5m x 0.5m maximum round base block below sole plate /pole jhama metal incl. cc (1:3:6) upto 1 meter

Supplying & Fixing PVC waterproof type looping cable box comprising of one 250 V 15 A kit-kat fuse unit , 6A SP MCB , 4pole star connector, one compression type brass cable gland for upto 4- core 16 sqmm PVC/A cable and having lined with rubber gasketted PVC top cover with brass machine screws etc., earthing terminal with lug, on steel tubular pole near base, including S&F 40x6 mm thick, MS clamps with bolts, nuts etc. including painting with anticorrosive paint(make: Sintex)

S&F 50 mm. dia 1.5 mtr. long detachable type G.I.Single arm bracket, suitable for pole head. The arm bracket shall be properly welded with 15 mm. thick stifner plate of pole sleeve for strengthening incl. properly fixing arrangement with the pole by bolts, nuts and washer as per direction of EIC.

Supply of 90 W Led Street Light Lumen Efficacy 120, CRI>70, CCT-5700K, IP- 66, IK-08, Aluminum Dia Cast Housing, with secondary Lens9Beam angle (60degree +- 10 %), Toughened Glass, Potted driver. Inbuild Surge Protection 5kv Internal & 10 kv external LM 79 Report shall be provided from manufactures own NABL Lab and LM 80 from Nichia/Osram/Seoul/Bridge Lux 5 Years Warranty. [Make- PANASONIC/PHILIPS/ WIPRO/Ansh Solar]

Supply of 45 W Led Street Light Lumen Efficacy 120, CRI>70, CCT-5700K, IP- 66, IK-08, Aluminum Dia Cast Housing, with secondary Lens9Beam angle (60degree +- 10 %), Toughened Glass, Potted driver. Inbuild Surge Protection 5kv Internal & 10 kv external LM 79 Report shall be provided from manufactures own NABL Lab and LM 80 from Nichia/Osram/Seoul/Bridge Lux 5 Years Warranty. [Make- PANASONIC/PHILIPS/ WIPRO/Ansh Solar]

Supply of 25 W Led Street Light Lumen Efficacy 120, CRI>70, CCT-5700K, IP- 66, IK-08, Aluminum Dia Cast Housing, with secondary Lens9Beam angle (60degree +- 10 %), Toughened Glass, Potted driver. Inbuild Surge Protection 5kv Internal & 10 kv external LM 79 Report shall be provided from manufactures own NABL Lab and LM 80 from Nichia/Osram/Seoul/Bridge Lux 5 Years Warranty. [Make- PANASONIC/PHILIPS/ WIPRO/Ansh Solar]

Distribution wiring for street light on pole with 2x1/1.40 PVC insulated and sheathed (single core) in 15 mm dia GI pipe (ISI Medium), without control switch incl. S&F 30.48 cm outdoor type dispersive light fitting with GI Pipe bracket and providing 25x6 mm Galv. MS flat clamps with bolts, nuts etc. and incl. painting (Av. run 3m)

Supply &Laying of 2core 10 sqmm of 1.1 KV grade alluminium XLPE Al. armoured LT cable, as directed by EIC. [Make : Havells/Polycab/RR Kabel/KEI/Gloster]

Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE/PVC armoured cables as below

2 Core 10 Sq.mm

Finishing the end of following XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials.

2 Core 10 Sq.mm

Supplying and Drawing 1.1 KV single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) of the following sizes in the prelaid polythene pipe and by the prelaid GI fish wire and making necy. connection as required 3 x 22/0.3 (2.5 sqmm), as per GS.

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S&F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level by ISI-Medium GI pipe, as per GS.

Excavation of soil for installation of Earth Electrode and filling & ramming, for Soft soil, as per GS.

Connecting the equipments body to earth busbar including S&F 20 mm x 3 mm galvanized (Hot Dip) MS flat on wall/floor with GI saddles as required and connection to equipments incl. drilling holes, with bolts, nuts, washers etc., as per GS. (for flyover continuous earthing)

Part- C ( SITC of Solar High Mast)

Stand Alone Solar PV High mast SITC of Octagonal GI pole (Hot Dip Galvanized) of 3 mm thickness 360 mm base dia, 150 mm top dia, for 9 mtr length High Mast Pole with base plate 500 mmX 500 namX 16 mm with foundation Bolt 24mm Dia X 600 mm length X4 nos along with arrangement with winch hand pulley system with suitable metallic rope or with metallic Ladder for maintenance (Make-SURYA/UTKARSH/GALPOL) Foundation Construction & Erection of suitable Shallow foundation upto 10mtr. Octagonal Pole with M-20 grade concrete for Pole considering soil bearing capacity (SBC) 10T/sq. mtr. at 2 Mtr. depth with all materials and labour payment made as per PWD civil schedule & as per direction of EIC. Erection of Pole by using of lifting equipment like hydra etc. and fixing of foundation bolts , anchor plate etc.

Solar Panel SITC of 4 nos 200 Wp Mono PERC PV module with IFC 61215, IEC 6173-1.2 compliance with any IS MNRE approved purpose of Luminaries and PV system (MAKE- PANASONIC/PHILIPS/ANSH SOLAR/WIPRO) Solar Light SITC of 4 nos 50 W Luminaries comprise of: a) 50 W LED with minimum coker temperature (CCT) 5500-6500%, mmmum typical luminous lux 150Lm/W ie minimum 7500Lm (MAKE- PANASONIC/PHILIPS/ANSH SOLAR/WIPRO) 5 YEARS COMPLETE CARE WARRANTY ON SITE. b) Charge controler with MPPT and efficiency 92% and it should have overcharge protection, deep discharge protection, Battery reverse polarity protection, Loud short circuit protection. Open circuit protection,Panel reverse polarity protection, Over temperature protection. c) Automatic dusk to drawn controlling system to monitor LED Operation d)With without dimmer arrangement.

Batteries SITC of 4 nos 12. 8 V. 100 Ah LITHIUM FERRO PHOSPHATE (Li FeP04) Batteries having BIS certificate. The batteries should have battery maragenient system (BMS) with higher life expectancy, longer cycle life low discharge rate and fast charging facilities. Battery should provide 12 Hr buckup. The battery must be provided with GI out door type battery box Inbuilt in Luminaries(Make- Exside/ANSH SOLAR/Surya ) Battery must have 5 yers warranty period. Cables and wires a) DC cable 4 sqmm & control cable as per requirment

Stand Alone Solar PV High mast SITC of Octagonal GI pole (Hot Dip Galvanized) of 3 mm thickness 360 mm base dia, 150 mm top dia, for 9 mtr length High Mast Pole with base plate 500 mmX 500 namX 16 mm with foundation Bolt 24mm Dia X 600 mm length X4 nos along with arrangement with winch hand pulley system with suitable metallic rope or with metallic Ladder for maintenance (Make-SURYA/UTKARSH/GALPOL) Foundation Construction & Erection of suitable Shallow foundation upto 10mtr. Octagonal Pole with M-20 grade concrete for Pole considering soil bearing capacity (SBC) 10T/sq. mtr. at 2 Mtr. depth with all materials and labour payment made as per PWD civil schedule & as per direction of EIC. Erection of Pole by using of lifting equipment like hydra etc. and fixing of foundation bolts , anchor plate etc.

Solar Panel SITC of 2 nos 200 Wp Mono PERC PV module with IFC 61215, IEC 6173-1.2 compliance with any IS MNRE approved purpose of Luminaries and PV system(MAKE - PANASONIC/PHILIPS/ANSH SOLAR/WIPRO.) Solar Light SITC of 2 nos 50 W Luminaries comprise of: a) 50 W LED with minimum coker temperature (CCT) 5500-6500%, mmmum typical luminous lux 150Lm/W ie minimum 7500Lm (MAKE- PANASONIC/PHILIPS/ANSH SOLAR/WIPRO) 5 YEARS COMPLETE CARE WARRANTY ON SITE. b) Charge controler with MPPT and efficiency 92% and it should have overcharge protection, deep discharge protection, Battery reverse polarity protection, Loud short circuit protection. Open circuit protection,Panel reverse polarity protection, Over temperature protection. c) Automatic dusk to drawn controlling system to monitor LED Operation d)With without dimmer arrangement.

Batteries SITC of 2 nos 12. 8 V. 100 Ah LITHIUM FERRO PHOSPHATE (Li FeP04) Batteries having BIS certificate. The batteries should have battery maragenient system (BMS) with higher life expectancy, longer cycle life low discharge rate and fast charging facilities. Battery should provide 12 Hr buckup. The battery must be provided with GI out door type battery box Inbuilt in Luminaries(Make- Exside/ANSH SOLAR/Surya ) Battery must have 5 yers warranty period. Cables and wires a) DC cable 4 sqmm & control cable as per requirment

M S KAMAL SHAW (BID ID -6996109)

M/S JOGMAYA ENTERPRISE (BID ID -6996125)