| 1 | Ceramic Tiles with weld plug and cover, Size -55 mm x 50 mm, 16 mm thick suitable for MDVs and MPOs of Coal Mill XRP-1003 | Thickness- 16mm. Alumina (AL2O3) content - 90 percent min. Hardness - More than 8 on moh scale. Bulk Density - More than or equal to 3.2 gm/cc. Hardness - greater than 8 on Mohs scale. Water absorption - Less Than 1 percent. Cold Crushing Strength - 3000 Kg/cm2 min. Flexure strength - 2200 Kg/ cm2 min. Co-efficient of thermal expansion - (7 to 9) x 10-6 mm per degree C. Service temp. �- Min 100 degree C and Max 1000-degree C. | 1,000 | No | [email protected] | 180 |
| 2 | VENTURY VANE WITH CERTILES PART NO-VA36130000515 | Ventury vane ceramic tiles of Coal Mill XRP-1003. (M.S. Shell Thickness -12mm confirming to IS-2062 GR. E-250 BR, Ceramic Liner Thickness - 15 plus minus 2mm, ceramic liner will be fixed by plug welding in MS shell, Adhesive Thickness - 2-3mm, Painting - One coat of red oxide primer and one coat of gray paint), Ceramic spec- Alumina (AL2O3) content - 90 percent min. Hardness - More than 8 on moh scale. Bulk Density - More than or equal to 3.2 gm/cc. Hardness- greater than 8 on Moh scale. Water absorption - Less Than 1 percent. Cold Crushing Strength - 3000 Kg/cm2 min. Flexure strength - 2200 Kg/ cm2 min.
Co-efficient of thermal expansion - (7 to 9) x 10-6 mm per degree C. Service temp. - Min 100 degree C and Max 1000-degree C. | 24 | No | [email protected] | 180 |
| 3 | Ceramic Tiles with weld plug and cover, Size-150 mm x 50 mm, 16 mm thick suitable for MDVs and MPOs of Coal Mill XRP-1003 | Thickness- 16mm. Alumina (AL2O3) content - 90 percent min. Hardness - More than 8 on moh scale. Bulk Density - More than or equal to 3.2 gm/cc. Hardness - greater than 8 on Mohs scale. Water absorption - Less Than 1 percent. Cold Crushing Strength - 3000 Kg/cm2 min. Flexure strength - 2200 Kg/ cm2 min. Co-efficient of thermal expansion - (7 to 9) x 10-6 mm per degree C. Service temp. �- Min 100 degree C and Max 1000-degree C. | 1,000 | No | [email protected] | 180 |
| 4 | Ceramic lined outlet venturi for XRP 1003 coal mill | Ceramic Lined venturi collar of Coal Mill x RP-1003. ( M.S. Shell Thickness -12 mm confirming to IS - 2062 GR. E250 BR, Ceramic tiles should be inside of shell, Ceramic Liner Thickness - 15 plus minus 2mm, (specification as per attached annexure- A), ceramic liner will be fixed by plug welding in MS shell, Adhesive Thickness - 02mm,Painting - One coat of red oxide primer and one coat of grey paint. (Dimension - As per sample available at BTPS Site) Ceramic spec - Alumina (AL2O3) content - 90 percent min. Hardness - More than 8 on moh scale. Bulk Density - More than or equal to 3.2 gm/cc. Hardness - greater than 8 on Moh�s scale. Water absorption - Less Than 1 percent. Cold Crushing Strength - 3000 Kg/cm2 min. Flexure strength - 2200 Kg/ cm2 min. Co-efficient of thermal expansion - (7 to 9) x 10-6 mm per degree C. Service temp. - Min 100 degree C and Max 1000-degree C. | 4 | No | [email protected] | 180 |
| 5 | ORIFICE ID- 551 PATTERN NO.3.01362.09 - 4 NOS. PER UNIT | Minimum Thickness of Ceramic Tiles- 20 mm. (2) Ceramic Tiles Material specifications -Alumina (AL2O3) content- 90 percent min. Hardness - More than 8 on moh scale. Bulk Density -More than or equal to 3.2 gm/cc. Hardness greater than 8 on Moh scale. Water absorption -Less Than 1 percent. Cold Crushing Strength - 3000 Kg/cm2 min. Flexure strength - 2200 Kg/ cm2 min. Co-efficient of thermal expansion - (7 to 9) x 10-6 mm per degree C. Service temp. - Min 100 degree C and Max 1000-degree C. (3) Cement/mortar should be used as bonding material to avoid falling of tiles due to failure of epoxied bonding material. (4) Profile of ceramic lining shall be uniform throughout and there should not be any gap between tiles to tile. (5) Material for outer casing- MS as per IS- 2062 Grade A (6) Exposed surface of casing shall be painted with Synthetic Enamel over a bare coat of Red Oxide on clean surface. (7) Item no. with ID should be clearly punched on outer periphery of the orifice for identification purpose. | 3 | No | [email protected] | 180 |
| 6 | ORIFICE ID-539 PATTERN NO.3.01362.05 -1NOS. PER UNIT | Minimum Thickness of Ceramic Tiles- 20 mm. (2) Ceramic Tiles Material specifications -Alumina (AL2O3) content- 90 percent min. Hardness - More than 8 on moh scale. Bulk Density -More than or equal to 3.2 gm/cc. Hardness greater than 8 on Moh scale. Water absorption -Less Than 1 percent. Cold Crushing Strength - 3000 Kg/cm2 min. Flexure strength - 2200 Kg/ cm2 min. Co-efficient of thermal expansion - (7 to 9) x 10-6 mm per degree C. Service temp. - Min 100 degree C and Max 1000-degree C. (3) Cement/mortar should be used as bonding material to avoid falling of tiles due to failure of epoxied bonding material. (4) Profile of ceramic lining shall be uniform throughout and there should not be any gap between tiles to tile. (5) Material for outer casing- MS as per IS- 2062 Grade A (6) Exposed surface of casing shall be painted with Synthetic Enamel over a bare coat of Red Oxide on clean surface. (7) Item no. with ID should be clearly punched on outer periphery of the orifice for identification purpose. | 1 | No | [email protected] | 180 |
| 7 | ORIFICE ID - 524 PATTERN NO.3.01362.02 - 2NOS. PER UNIT | Minimum Thickness of Ceramic Tiles- 20 mm. (2) Ceramic Tiles Material specifications -Alumina (AL2O3) content- 90 percent min. Hardness - More than 8 on moh scale. Bulk Density -More than or equal to 3.2 gm/cc. Hardness greater than 8 on Moh scale. Water absorption -Less Than 1 percent. Cold Crushing Strength - 3000 Kg/cm2 min. Flexure strength - 2200 Kg/ cm2 min. Co-efficient of thermal expansion - (7 to 9) x 10-6 mm per degree C. Service temp. - Min 100 degree C and Max 1000-degree C. (3) Cement/mortar should be used as bonding material to avoid falling of tiles due to failure of epoxied bonding material. (4) Profile of ceramic lining shall be uniform throughout and there should not be any gap between tiles to tile. (5) Material for outer casing- MS as per IS- 2062 Grade A (6) Exposed surface of casing shall be painted with Synthetic Enamel over a bare coat of Red Oxide on clean surface. (7) Item no. with ID should be clearly punched on outer periphery of the orifice for identification purpose. | 1 | No | [email protected] | 180 |
| 8 | ORIFICE ID - 632 PATTERN NO.3.01362.13 -1NOS. PER UNIT | Minimum Thickness of Ceramic Tiles- 20 mm. (2) Ceramic Tiles Material specifications -Alumina (AL2O3) content- 90 percent min. Hardness - More than 8 on moh scale. Bulk Density -More than or equal to 3.2 gm/cc. Hardness greater than 8 on Moh scale. Water absorption -Less Than 1 percent. Cold Crushing Strength - 3000 Kg/cm2 min. Flexure strength - 2200 Kg/ cm2 min. Co-efficient of thermal expansion - (7 to 9) x 10-6 mm per degree C. Service temp. - Min 100 degree C and Max 1000-degree C. (3) Cement/mortar should be used as bonding material to avoid falling of tiles due to failure of epoxied bonding material. (4) Profile of ceramic lining shall be uniform throughout and there should not be any gap between tiles to tile. (5) Material for outer casing- MS as per IS- 2062 Grade A (6) Exposed surface of casing shall be painted with Synthetic Enamel over a bare coat of Red Oxide on clean surface. (7) Item no. with ID should be clearly punched on outer periphery of the orifice for identification purpose. | 1 | No | [email protected] | 180 |
| 9 | ORIFICE ID - 591 PATTERN NO.3.01362.12 -1NOS. PER UNIT | Minimum Thickness of Ceramic Tiles- 20 mm. (2) Ceramic Tiles Material specifications -Alumina (AL2O3) content- 90 percent min. Hardness - More than 8 on moh scale. Bulk Density -More than or equal to 3.2 gm/cc. Hardness greater than 8 on Moh scale. Water absorption -Less Than 1 percent. Cold Crushing Strength - 3000 Kg/cm2 min. Flexure strength - 2200 Kg/ cm2 min. Co-efficient of thermal expansion - (7 to 9) x 10-6 mm per degree C. Service temp. - Min 100 degree C and Max 1000-degree C. (3) Cement/mortar should be used as bonding material to avoid falling of tiles due to failure of epoxied bonding material. (4) Profile of ceramic lining shall be uniform throughout and there should not be any gap between tiles to tile. (5) Material for outer casing- MS as per IS- 2062 Grade A (6) Exposed surface of casing shall be painted with Synthetic Enamel over a bare coat of Red Oxide on clean surface. (7) Item no. with ID should be clearly punched on outer periphery of the orifice for identification purpose. | 1 | No | [email protected] | 180 |
| 10 | ORIFICE ID - 529 PATTERN NO.3.01362.03 - 2NOS. PER UNIT | Minimum Thickness of Ceramic Tiles- 20 mm. (2) Ceramic Tiles Material specifications -Alumina (AL2O3) content- 90 percent min. Hardness - More than 8 on moh scale. Bulk Density -More than or equal to 3.2 gm/cc. Hardness greater than 8 on Moh scale. Water absorption -Less Than 1 percent. Cold Crushing Strength - 3000 Kg/cm2 min. Flexure strength - 2200 Kg/ cm2 min. Co-efficient of thermal expansion - (7 to 9) x 10-6 mm per degree C. Service temp. - Min 100 degree C and Max 1000-degree C. (3) Cement/mortar should be used as bonding material to avoid falling of tiles due to failure of epoxied bonding material. (4) Profile of ceramic lining shall be uniform throughout and there should not be any gap between tiles to tile. (5) Material for outer casing- MS as per IS- 2062 Grade A (6) Exposed surface of casing shall be painted with Synthetic Enamel over a bare coat of Red Oxide on clean surface. (7) Item no. with ID should be clearly punched on outer periphery of the orifice for identification purpose. | 1 | No | [email protected] | 180 |