Construction of Anicut across Paralaiyar to feed Kattumaneswaram Tank in Valimarichan Village in Paramakudi Taluk in Ramanathapuram District.

Amount

Clearing Scrub jungle and destroying them effectively as directed by the departmental officers.

Clearing juliflora jungle with uprooting as directed by the Engineer complying with standard specification.

Earth work excavating and depositing on bank with a initial lead of 10 m & initial lift of 2 m in Hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders etc., complete complying with standard specification and as directed by the departmental officers. - SS.20B (Cut Open Bund)

Earthwork excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size of boulders hard gravelly soil inclusive of shoring to full depth strutting and bailing out water wherever necessary and refilling the sides of foundation with excavated soil other than sand in layers of not more than 15 cm thick, well rammed, consolidated and depositing the surplus earth in places as shown by the departmental officers with an initial lead of 10 metres and initial lift of 2 metres and clearing, levelling the site etc., complete complying with standard specification and as directed by the departmental officers.

Providing and placing Plain Cement Concrete M10 grade using crusher broken hard coarse aggregate (well graded) of nominal maximum size of 40mm and downgraded to I.S specified grading (To achieve the specified characteristic strength of 10N/mm2 in 28 days) and mixing the ingredients in approved mixer including dewatering of the placement site by baling / pumping and diverting wherever necessary, placing concrete in layers, water curing, finishing the surface with all leads and lifts compacting and finishing the surface watering, curing wherever necessary for various depth and height below and above ground level so as to attain the profile and strength specified in the drawings etc., complete complying with standard specification and as directed by the Departmental Officers. (without vibration).

Below Ground Level (Upto 1.50 m)

Providing and placing Plain Cement Concrete M15 grade using crusher broken hard coarse aggregate (well graded) of nominal maximum size of 20mm and downgraded to I.S specified grading (To achieve the specified characteristic strength of 15N/mm2 in 28 days) and mixing the ingredients in approved mixer including dewatering of the placement site by baling / pumping and diverting wherever necessary, placing concrete in layers and vibrating, water curing, finishing the surface with all leads and lifts etc., complete complying with standard specification and as directed by the Departmental Officers.(Field Channel Wearing coat) (with out vibration)

Below Ground Level (Upto 1.50 m) to 1.00 AGL

Below Ground Level (1.50 m to 4.50 m)

Providing and placing in position of plain Cement concrete of grade M15 using hard well graded aggregates with the nominal maximum size of coarse aggregate of 40mm (60%) and 20mm (40%); weigh batching the ingredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 15 N/mm2 at 28days) including dewatering the placement site by bailing/pumping and by diverting wherever necessary; laying the concrete in layers of not exceeding 15 cm thick and in bays; vibrating, compacting and finishing the surface with all leads and lifts; watering curing complete so as to attain the profile and strength specified in the approved drawing & specifications etc., complete complying with standard specification and as directed by the Departmental Officers. with vibration.

Below Ground Level up to 1.50m to 1.00 AGL

Below Ground Level up 1.50m to 4.50 M

Above ground level Upto 1.00 to 4.5m

Providing and laying in position of Standardised Concrete Mix M25 in accordance with IS 456-2000 using 20 mm down graded hard broken granite stone jelly for all RCC items of works with minimum cement concrete of 350 kg/m3 and maximum water cement ratio of 0.55 with about (5 cum) 7730 kg of 20 mm machine crushed stone jelly and with about (3.30 cum) 5156 kg of 10 - 12 mm machine crushed stone jelly and with about (4.79 cum) 7670 kg of sand weigh batching the ingredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 25N/mm2 at 28days) including dewatering of placement site by bailing/pumping and by diverting wherever necessary laying the concrete in layers and in bays, Vibrating, compacting and finishing the surface water curing so as to attain the profile and strength specified in the approved drawing and specification and excluding the cost component of providing rigid and smooth centering and shuttering wherever necessary for various depths below ground level and various heights above ground level as per the direction of the Engineer complete in all respect but excluding the cost and placing of reinforced grill in position complying with standard specification

Below Ground Level up to 1.50m to 1.00 AGL

Above ground level Upto 1.00 to 4.5m

Providing Steel centring for RCC Slabs, beams or plain surfaces including strutting upto 3.29 m high using MS sheets, 10 guage thick of size 90cm x 60cm, Stiffened with Ms angles of size 25mm x 25mm x 3mm laid over silver oak joists of size 10 cm x 6.5 cm spaced at 90 cm c/c and supported by casurina props of 10 cm to 13cm dia spaced at 75 cm c/c and removing the centring and shuttering after specified period without damaging the concrete laid, etc., complete complying with standard specification and as directed by the Departmental Officers. (For Retaining walls and Sluices) With strutting

Without Strutting

With Strutting

Providing and laying in position of Standardised Concrete Mix M20 in accordance with IS 456-2000 using 20 mm down graded hard broken granite stone jelly for all RCC items of works with minimum cement concrete of 325 kg/m3 and maximum water cement ratio of 0.55 with about (5 cum) 7730 kg of 20 mm machine crushed stone jelly and with about (3.30 cum) 5156 kg of 10 - 12 mm machine crushed stone jelly and with about (4.79 cum) 7670 kg of sand weigh batching the ingredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 20N/mm2 at 28days) including dewatering of placement site by bailing/pumping and by diverting wherever necessary laying the concrete in layers and in bays, Vibrating, compacting and finishing the surface water curing so as to attain the profile and strength specified in the approved drawing and specification and excluding the cost component of providing rigid and smooth centering and shuttering wherever necessary for various depths below ground level and various heights above ground level as per the direction of the Engineer complete in all respect but excluding the cost and placing of reinforced grill in position complying with standard specification

Above Ground Level up to 1.00 to 4.50 m )

Below Ground Level up to 1.50m to 1.00 AGL

Supplying, fabricating and placing in position of HSD (high Yield Strength) bars for all reinforced cement concrete works including cost of binding wire, steel rods, conveyance charges and labour charges etc., complete complying with standard specification and as directed by the Departmental Officers. (Specification No.9.1 to 9.12.1) cutting, bending and tying the grills complete complying with standard specification. Steel and binding wire will be at the contractor's own cost.

Providing filter zone below the concrete block with course sand for bottom layer and broken graded stone for top layers as furnished in the drawing and as directed by the Engineer including collection of course sand conveying stacking the same for premeasurement and providing a layer of 20cm thick watering and consolidating supplying hard broken stone of the following size stacking for premeasurement laying the stones of 10mm size for 7.5 cm thick, 20mm size for 7.5cm thick, 40mm size for 10 cm thick, 80mm size for 15 cm thick in layer and packing etc.,complete complying with standard specification and as directed by the Engineer incharge of work

Gravel backing for apron and revetment of 15cm thick including the cost of gravel at site of work, mixing with water so as to form into stiff plastic balls and laying and finishing etc., complete complying with standard specification.

Providing supplying and fixing in position of serrated with central bulb , off white coloured PVC water stopper of size 305 mm X 9 to 12 mm for the expansion joints with necessary arrangement, including loading, conveyance and unloading etc.as directed by the departmental officers complete complying with standard specification.

Rough stone dry packing using new stones for apron and revetment including stacking charges for premeasurements and finishing etc,complete complying with standard specification and as directed by the specification and as directed by the departmental officers

Providing and fixing weep holes of 110mm dia pvc pipes of working pressure 4kg/m2 to a required length for protection wall, abutment and wing wall including cost of conveyance of all materials to work site including cost of labour charges for 90cm spherical back fill arrangements with 110mm dia and 20mm size hard granite broken stone charges at the peripery, the labour charges for fixing and to drain the back fill etc., complete complying with the standard specifications and as directed by the departmental officers.

Dewatering using 3hp to 70hp diesel engine pumpset including Hire charges, cost of Diesel, Engine oil, pump operator, labour charges, conveyance of pumpset and fuel to site and back, loading, unloading and any other incidental charges etc., complete.

Fabricating, Supplying and erection of Screw gearing steel shutters of size above 1.00 m and upto 2.00m width consist of skin plate made out of 8mm thick mild steel plate and horizontally stiffened with 100x50mm mild steel channel at an interval not more than 0.50m and vertical stiffeners made out of same section at an interval not more than 0.60m and provided with 8mm thick mild steel gusset plate of required size on both sides fastened with rust free bolts and nuts etc. Conveying the fabricated shutter by using lorries including loading, unloading and leading the shutter to the vent. Dismantling the eroded shutter and shuttering arrangements by using necessary gas cutting equipment. Erecting the new shutter and the shuttering arrangements in the vent in proper position by using necessary hoisting equipment. The shutter shall be painted with two coats of Anticorrosive black paint over one coat of Red Oxide Primer. The rate including cost of materials consumables, labours power charges, conveyance charges for all equipment required conveying the dismantled materials to the section stores, cost of petty civil works, trial operation of shutter and warranty for 5 years etc.,complete.

Fabricating, supplying and fixing of 63mm dia Screw Rod made up of Mild Steel duly machined and fully threaded to suit the Head set Assembly and provided with required holes. Conveying and leading the screw rod to the worksite. Fixing the screw rod to the shutter gusset plate with required bolt and nut in proper alignment to the head set including dismantling the existing damaged screw rod,conveying and stacking at section store. The Screw rod should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, labours, charges for all fabricating and hoisting equipments, conveyance charges for labours and materials and warranty for 5 years etc., complete

Fabricating, supplying and fixing of Shutter Groove Angle made up of 100x100x10mm Mild Steel angle for required height including welding hold fast of size 40x40x6mm Mild steel angle 3 Nos on both sides and conveying and leading the groove angle to the vents. Fixing the angle to the grooves in proper alignment including dismantling the existing damaged groove angles, conveying and stacking at section store. The groove angle should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, consumables, labours, charges for all fabricating and hoisting equipments, conveyance, petty civil works and warranty for 5 years etc., complete.

Supplying and fixing of Head Set Assembly medium duty with hexagonal nut (Approximate 70 Kg) made up of cast iron including moulding, machining and the hexagonal nut threaded to suit the Screw Rod provided with thrust bearings for smooth operation. Conveying and leading the head set assembly to the work site. Fixing the head set assembly to the top beam by using required rust fre bolts and nuts in proper alignment including dismantling the existing damaged Head set assembly, conveying and stacking at sectio store. The Head set assembly supplied with operating key and the both should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, labours charges for wooden pattern, moulding and charges for labours and materials and warranty for 5 years etc., complete.

Fabricating, Supplying and fixing of Top Beam made up of 200x100mm (ISMB 200) duly drilled to suit the Head Set Assembly with required bed bolt made out of 25mm mild steel round rod duly threaded with suitable anchorage arrangements to a height of 0.60m with necessary Fish plate made out of 16mm mild steel plate of size 0.20x 0.30m 2 Nos with required holes.Conveying and leading the top beam arrangements to the work site. Fixing the top beam arrangements at the top of the vent in correct position including dismantling the existing eroded top beam, conveying and stacking and the section stores. The top beam should be painted with two coats of AC black paint over one coat of Red Oxide primer. The Rate including cost of materials, labours, charges for all fabricating and hoisting equipments, cost of petty civil works conveyance charges for labours and materials and warranty for 5 years etc.., complete.

Painting with two coats of coaltarepoxy paint over two coat good quality zinc rich primer. This includes cleaning the surface to be painted to remove grease, oil and other impurities and coating the surface with Zinc rich primer (85% ±5% zinc content)as per IS 14177:1994 and then application of two coats of coaltar epoxy paint

Supplying and fixing of Bottom Flat Rubber seal with Mild Steel Flat plate throughout the length of Rubber seal and fitted with the existing structure by means of Mild Steel Washers, Nuts and Bolts including dismantling the old corroded bolts by cutting, removing old flats and hardened or damaged old rubber seals beam, then conveying, loading and unloading and stacking to section store, etc.., complete.

Fabricating, Supplying and erection of Screw gearing steel shutters of size above 1.00 m and upto 2.00m width consist of skin plate made out of 8mm thick mild steel plate and horizontally stiffened with 100x50mm mild steel channel at an interval not more than 0.50m and vertical stiffeners made out of same section at an interval not more than 0.60m and provided with 8mm thick mild steel gusset plate of required size on both sides fastened with rust free bolts and nuts etc. Conveying the fabricated shutter by using lorries including loading, unloading and leading the shutter to the vent. Dismantling the eroded shutter and shuttering arrangements by using necessary gas cutting equipment. Erecting the new shutter and the shuttering arrangements in the vent in proper position by using necessary hoisting equipment. The shutter shall be painted with two coats of Anticorrosive black paint over one coat of Red Oxide Primer. The rate including cost of materials consumables, labours power charges, conveyance charges for all equipment required conveying the dismantled materials to the section stores, cost of petty civil works, trial operation of shutter and warranty for 5 years etc.,complete.

Fabricating, supplying and fixing of 63mm dia Screw Rod made up of Mild Steel duly machined and fully threaded to suit the Head set Assembly and provided with required holes. Conveying and leading the screw rod to the worksite. Fixing the screw rod to the shutter gusset plate with required bolt and nut in proper alignment to the head set including dismantling the existing damaged screw rod,conveying and stacking at section store. The Screw rod should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, labours, charges for all fabricating and hoisting equipments, conveyance charges for labours and materials and warranty for 5 years etc., complete

Fabricating, supplying and fixing of Shutter Groove Angle made up of 100x100x10mm Mild Steel angle for required height including welding hold fast of size 40x40x6mm Mild steel angle 3 Nos on both sides and conveying and leading the groove angle to the vents. Fixing the angle to the grooves in proper alignment including dismantling the existing damaged groove angles, conveying and stacking at section store. The groove angle should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, consumables, labours, charges for all fabricating and hoisting equipments, conveyance, petty civil works and warranty for 5 years etc., complete.

Supplying and fixing of Head Set Assembly medium duty with hexagonal nut (Approximate 70 Kg) made up of cast iron including moulding, machining and the hexagonal nut threaded to suit the Screw Rod provided with thrust bearings for smooth operation. Conveying and leading the head set assembly to the work site. Fixing the head set assembly to the top beam by using required rust fre bolts and nuts in proper alignment including dismantling the existing damaged Head set assembly, conveying and stacking at sectio store. The Head set assembly supplied with operating key and the both should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, labours charges for wooden pattern, moulding and charges for labours and materials and warranty for 5 years etc., complete.

Fabricating, Supplying and fixing of Top Beam made up of 200x100mm (ISMB 200) duly drilled to suit the Head Set Assembly with required bed bolt made out of 25mm mild steel round rod duly threaded with suitable anchorage arrangements to a height of 0.60m with necessary Fish plate made out of 16mm mild steel plate of size 0.20x 0.30m 2 Nos with required holes.Conveying and leading the top beam arrangements to the work site. Fixing the top beam arrangements at the top of the vent in correct position including dismantling the existing eroded top beam, conveying and stacking and the section stores. The top beam should be painted with two coats of AC black paint over one coat of Red Oxide primer. The Rate including cost of materials, labours, charges for all fabricating and hoisting equipments, cost of petty civil works conveyance charges for labours and materials and warranty for 5 years etc.., complete.

Painting with two coats of coaltarepoxy paint over two coat good quality zinc rich primer. This includes cleaning the surface to be painted to remove grease, oil and other impurities and coating the surface with Zinc rich primer (85% ±5% zinc content)as per IS 14177:1994 and then application of two coats of coaltar epoxy paint

Supplying and fixing of Bottom Flat Rubber seal with Mild Steel Flat plate throughout the length of Rubber seal and fitted with the existing structure by means of Mild Steel Washers, Nuts and Bolts including dismantling the old corroded bolts by cutting, removing old flats and hardened or damaged old rubber seals beam, then conveying, loading and unloading and stacking to section store, etc.., complete.

Earthwork in all soils except hard rock requiring blasting and conveying for formation of bund with a lead of 1KMCT + 1KMMR+ 1KMCT deploying earth moving machinery and tippers including benching ,formation of bunds, breaking clods ,sectioning ,compaction by power roller with watering and consolidation in layers not more than 15cm thick etc complete. (for bund formation)

Towards the payment of Mineral charges, Seigniorage fee, Green fund, District mineral fund and tax on Mineral Bearing Land for formation of flood bank to be paid to Revenue through the contractor etc. (Excluding cost of Earthwork excavation, conveyance and forming flood bank). (Ref: 1.G.O. 4 Natural Resources (MMC - 1) Department dated 22.08.2023, 2.G.O. (M No 23. Industries (MME - 1), Department dated 23.02.2022, 3.Tamilnadu Mineral Bearing Land Tax Act.2024.

K A I G CONSTRUCTIONS PRIVATE LIMITED (BID ID -1445429)

KVCS CONSTRUCTIONS COMPANY (BID ID -1444483)