CWE/P-67/2019-20 CERTAIN REPAIR TO B R AND E M WORKS IN MD OTM ACCN AT 6 BIHAR UNDER GE (WEST) PATHANKOT

Amount

Dismantling floor, hearth or wall tiling of any description including cement Mortar bedding (but not backing) and removing serviceable tiles to the stores and rubbish off the premises complete all as specified and directed.

M & L for 15 mm thick screed bed or bedding layer of mortar for laying floor finishes etc in cement Mortar 1:6 complete all as specified and directed.

M &L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as directed

M & L glazed ceramic coloured tiles (first quality) of size 300 x 450x7mm thick on vertical surfaces such as dado etc set and jointed in neat cement slurry and pointed in colour cement to match the shade of the tiles complete complete complete all as specified and directed including 10mm thick rough cement plaster to receive stone in cement mortar 1:4 and dismantling existing tile on floor/wall complete all as specified and directed Note: Rates for this item is also including for necessary raking circular cutting or notching and waste on tiles

M&L non abrasive paving ( endura) tiles 300mm x 300mm x10mm thick machine pressed) (square/ rectangular) polished, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement and including 15mm screed bed cement mortar 1:4 to match complete all as specified and directed

M&L 18/20 mm thick granite (black) work (table rubbed and polished) cills, cooking platforms, in steps, jambs, pillars, window-cill and like including 10mm thick cement mortar (1:4) screed bed including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed Note : All Open Edges to be Half rounded.

M&L coloured (using pigment) chequered cement concrete tiles (design and colour as approved by GE) of size 300 x 300 x 25mm thick casted in rubber moulds with vibro process complete all as specified and directed

Demolition of un reinforced concrete in ground floors and pavings not exc 15 cm thick (below or above ground level ) and removing rubbish to a distance exc 250 m but not exc 1.5 km complete all as specified and directed

M & L 75 mm thick PCC as in plinth protection / hard standing /apron type C-1, 1:3:6 (20 mm graded crushed stone aggregate) finishing cement surfaces even and fair and make impression with wire netting complete all as specified & directed.

M&L for plain cement concrete 1:2:4 type B-1(using 20mm graded crushed stone aggregate) as in floor 40mm thick finished even and smooth without using extra cement or as specified or as directed

Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including racking out joints, hacking for key, scrubbing down with water etc.& removing rubbish to a disance not exc 250m complete all as specified & directed.

M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces with cement mortar 1:4 and is to be finished even and smooth without using extra cement complete all as directed and specified

M&L rendering 10mm thick on other fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed

M&L rendering 5mm thick on fair faces of brickwork or concrete surfaces in cement mortar 1:3 as on ceiling finished even and smooth without using extra cement complete all as specified and directed

M&L for two coat plaster 35 mm thick (20 mm + 15 mm) on rough concrete surfaces of fin, facia, chhajja and similar article such as beams etc. in cement mortar 1:3 finished even and smooth without using extra cement in any height including necessary scaffolding complete all as specified & directed. Note :- Two coat plaster shall be carried out as mentioned in clause 14.18 of SSR-2009, Part-I.

M&L for preparation of new plastered surfaces of wall treating the surface with chalk whitening to make surface smooth including two coats of distempering of wall with distemper oil emulison (any tint) complete all as specefied and directed.

M&L for preparation of old plastered surfaces of wall and washing of existing treatment and treating the surface with a chalk whitening to make surface smooth and applying two coats of distempering of wall with distemper oil emulison (any tint) complete all as specified and directed Note: Removing existing nails and filling with putty is included in the quoted rates

M&L for preparation of new plastered surfaces and applying two coats of colour wash (any tint) complete all as specified and directed

M&L for preparation of old plastered surfaces by complete removal and washing of existing treatment and treating the surface with a two coat of colour wash any tint complete all as specified and directed.

M & L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified

M & L for preparation old plastered ceilling surfaces and complete removal and washing of existing treatment and applying two coats of white wash complete all as directed

M & L for preparation of old treated wooden surfaces of any description exc 10 cm in girth and applying a coat of synthetic enamel paint completed all as directed.

M & L for preparation of old treated steel surfaces of any description exc 10 cm in girth and applying a coat synthetic enamel paint completed all as directed .

M&L Disconecting water tank exceeding 250 Ltrs and n.exc 500 Ltrs and removing to store complete all as specified and directed.

S&F rotational moulded polythene water storage tank (tripple layer) ISI marked (Cylindrical vertical with closed top hoisted fixed in position all as specified capacity of tank 500 ltrs including inlet and out let connections 20 mm air and 15 mm dia GI pipe medium grade complete all as specified and directed.

S & F 20 mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms ) complete all as specified and directed

Taking down steel water tubing of 15 mm dia bore incl connection & removal to store complete all as specified and directed

Taking down steel water tubing of 20 mm dia bore incl connection & removal to store complete all as specified and directed

Refixing old 15mm steel tubing and connections in new or old position (Walls, ceiling, floors, etc complete all as specified and directed.

S&F Mild steel GI tubing 15 mm bore medium weight with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F Mild steel GI tubing 20 mm bore medium weight with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F in repairs Stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repair vitreous china squatting pan, Orissa pattern size 580mm x 440mm white with integral foot rest including provision of cement concrete bedding, connection to drain out pipe and to flush pipe, anti syphonage pipe etc complete including making complete all as specified and directed.

S&F in repair 10 litres capacity PVC low level flushing cistern syphonic action type with inlet ball valve float and push type handle including bracket, PVC 32mm dia flush pipe with coupling fixed complete all as specified and directed.

S&F in repairs vitreous China wash basin,white or in matching colour of tiles ,size 550x450 mm excluding taps,but including 32 mm dia waste coupling chromium plated brass and PVC waste pipe 750 mm long( Minimum), chain and plug and porcelain stopper, brackets for fixing any size, including cutting for and pinning in ends or erecting stand as directed.

S&F in repairs 20 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&Fin repairs swan neck long type Pillar tap (minimum weight 700gms), cast copper alloy 15 mm bore, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

Supply and fix in repair Chromium plated bib taps (minimum weight 575gms), cast copper alloy with copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule 15 mm bore complete all as specified and directed

Supply and fix in repair Chromium plated stop cock/angle valve (minimum weight 575gms), cast copper alloy screwed down high pressure ,with crutch or butterfly handle screwed both ends for iron pipe or for union of 15 mm bore complete all as spd & directed

S&F stop valve chromium plated 15 mm bore fancy type with long shank and cup (concealed type) screwed down high pressure ,with crutch or butterfly handle screwed both ends for iron pipe or for union of 15 mm bore complete all as spd & directed .

S & F in repairs brass chromium plated shower rose 125 mm size with chromium plated extention tube complete all as specified and directed

S&F Tubular towel rail (minimum weight 600gms), 20mm dia ‘D’ type 60cm long between flanges brass chromium plated complete all as specified and directed.

S & F curtain rod 25 mm dia of pre painted aluminium with fixing brackets, stops, rollers, knob etc complete all as directed.

S&F PVC connection 15 mm dia with PTMT nuts of length 450 mm complete all as specified and directed.

Dismantling of cast iron,PVC or reinforced concrete soil waste and drain pipe, 50/75/100 mm dia, jointed in cement mortar or lead and taking out of trenches, if required

S&F PVC (SWR) pipes 75 mm bore, single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F PVC (SWR) pipes 110 mm bore, single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F PVC (SWR) bends 110 mm bore any radius complete all as specified and directed.

S&F PVC (SWR) bends 75 mm bore any radius complete all as specified and directed.

S&F Salt-glazed stoneware gully traps of size 150 mm x150 mm, square or round mouthed, tvpe 'P' complete all as specified and directed.

S&F PVC (SWR) junction single,(Single T) equal or unequal of 110mm complete all as specified and directed.

S&F PVC (SWR) junction single,(Single T) equal or unequal of 75mm complete all as specified and directed.

S&F PVC (SWR) vent cowl 110mm complete all as specified and directed.

S&F PVC (SWR) vent cowl 75mm complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed.

S&F 150mm UPVC Pipes (SCH-80) 8KN complete all as specified and directed

M & L Concrete bed to drain pipes (150 mm dia) including packing under, and haunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D2 complete all as specified and directed

Returning, filling in, including spreading, levelling, watering & well ramming in layers n exc 25 cm with any type of soil complete all as specified and directed.

Removing excavated material n exc 50 m and depositing where directed at al level n. exc 1.50 m above the starting point complete all as specified and directed.

Surface excavation n.exc (not exceeding) 45 cm deep and averaging 30cm deep and getting out soft and loose soil complete all as specified and directed

M&L Shingle filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled, and blinded with earth and rammed including watering complete all as specified and directed.

M&L 100 mm thick PCC 1:4:8 type D-2 (with using 40mm graded crushed stone aggregate) as in floor and finishing even and smooth with using extra cement and spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green complete all as specfied and directed.

S&F bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M & L for cleaning of all foreign material such as fungus, mass dustetc by brushing and dusting, sprinkle water on surface surface shall be levelled with a layer of 20 mm thick cement mortar (1:4) mixed with water proofing admixture as per manufacture's instrutions and applying polymer APP modified membrane with non woven ployster reinforcement/mat with thermal insulation with white mineral gravel finished on upper side of weight not less than 3.5Kg/Sqm and thicknes not less than 3mm laid with overlap 100mm on length side and 100mm on the width side over a coat of hot blown bitumen 85/25 @ 1.2 Kg/Sqm over bituminous oil based primer (IS-3384)@ 0.4 litre/Sqm on prepared surface all as specified and directed including demolition of existing roof treatment of any thickness and description.

Taking down chowkat with shutter (without taking off shutter from frame) exc 1.5 sqm but n.exc 4 sqm each complete all as specified and directed.

Taking down chowkat with shutter (without taking off shutter from frame) n exc 1.5 sqm each complete all as specified and directed.

Taking down shutter exc 1 sqm but n exc 2 sqm each and remove to store yard complete.

Taking down easing and adjusting and refixing shutter exc 1 sq. m and n exc 2 sq. m each in same openinG complete all as specified and directed

S&F steel window/ventilator factory made out of box type and shutter (double shutter) with sash bar made out of section using flash butt welding hinges shall be provided to both shutters complete including all fittings including 10mm square bar grills, glazing (glass pane), gauging (wire mesh) and two coat synthetic enamel paint over a coat of red oxide primer all as drg No CEPZ/TD/245/01 sh 1/1 CEPZ- TD/246/01 sheet 1/2 and sheet 2/2 all a specified and directed by Engr-in-Charge

S&F Solid PVC door/window frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube, above but wood grain printed PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with printed sheet complete all as specified and directed.

S&F factory made Solid Panel prelam PVC door shutters 30 mm thick (style) consisting of frame made out of MS tubes of 19 guage thickness and size of 40mmx20mm for stiles as well as top, lock and bottom rails. MS frame shall have a coat of metal primer of approved make. M S frame shall be covered with heat moulded prelam PVC ‘C’ channel made of 5mm thick PVC sheet of density 600kg/cum manufactured by an ISO-9001-2008 certified company, of thickness 110mm width forming stiles in which 100mm should be flat and 5mm should be taper and 5mm thick, 135mmwide PVC sheet for top rail and bottom rail in which 125mm should be flat and 5mm should be tapper on either side of panel. also for the lock rail 145mm sheet , 125mmshould be flat and 5mm tapper on either side. an additional 5mm thick PVC strip of 20mm width is to be stuck on inner side of C chanel using PVC solvent cement adhesive. Panelling of 10mm Prelam PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with 30mm wide x 5mm thick PVC sheet beadings on either side and additional 30mm wide PVC beading as gap insert bellow top and bottom rails complete all as specified and directed.

M&L Pressed steel frames 125 x 60 mm for doors with one or more rebates including necessary fixing lugs,MS hinges, lock strike plate,etc.,including filling of cement concrete type B-1 ,1:2:4(using 20mm graded crushed stone aggregate) as in filling hollow of frame with plain concrete and hold fast 300mm FI 25 X 6 three numbers each side complete, as specified,supplied and fixed

S&F 35mm Factory made Plain framed, panelled shutter second class Hard wood (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed

S&F 35mm Glazed and skeleton shutters of second class Hard wood, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats

S&F Factory Made Solid PVC flush door shutter with wood free EPS core, 28 to 30mm thick (stiles), with 5mm thick prelam PVC Sheet on the front face & 5mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing

S&F sheet glass ordinary quality 3 mm thick and glazing with oil putty ang glazing clips in squares n. exc 0.50 sqm each pane complete all as specified and directed.

S&F Sheet glass ordinary quality, ground or obscured or frosted, on one side 3 mm thick and glazing with oil putty and glazing clips in squares n. exc 0.50 sqm each pane complete all as specified and directed.

Supply and fix in repair stainless steel cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or using metal nut and bolts complete all as specified and directed.

S&F 100mm Butt hinges, heavy weight, cold rolled mild steel, and fixed complete all as directed

S&F 100mm Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and directed.

S&F aluminium anodised, 150 mm long barrel tower bolt of extruded section complete all as specified and directed.

S&F 250mm mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed Complete all as specified and directed

S&F 300 mm long mild steel ordinary rat tail rod paltren spring incl roller and roller plate complete all as specified and directed.

Supply and fix in repair hasp and staple of size 100 mm, aluminium anodised, including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete, drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings as specified and as directed by Engr-in-Charge

Dismantling of old asbestos cement corugated,semi corrugated etc) sheets in roof coverings complete all as specified and directed

S&F mild steel angle iron or hollow section fixed in wall for chowkhats with hold fast including welding,angle iron support for chajjas/slab or similar works as specified or as directed by Engr-in-Charge

M&L for Prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws/type hooks as specified

Demolition of brick work or stone masonry built in cement mortar including all quoines arches,pillar etc but excluding ashlar facing , dressed stone work and precast concrete articles complete all as specified.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:4.

Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in cm 1:4 as in half bricks.

S&F in repairs prelaminated PVC board 18/19mm , interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

S & F Continuous (piano) hinges 30mm wide, mild steel, bright finish or electrogalvanised complete all as specified and directed

Demolition of reinforced concrete not exc 15 cm thick and removing rubbish to a distance exc 250 m but not exc 1.5 km complete all as directed.

Material and labour for providing Precast RCC 1:2:4, Type B-1 using 20mm graded stone aggregate as in landings, cover slabs [for manholes etc], chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar 1:6 complete all as specified and as directed by the Engineer -in- Charge.

M & L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No 97 here-in-before but 8 to 10 mm dia as in stirrups

Rooting out trees, flora & fauna and foliage as grown on RCC roof surfaces and brick walls by cutting hole into slabs/walls for digging out roots and using certain chemical to burn deep rooted tree roots etc and making good dirturb portion of wall/roof with cement concrete 1:2:4 type B 1 (using 20 mm graded crushed stone aggregate) complete all as specified and directed.

Taking down old unserviceable copper/aluminium point wiring (light, fan, socket , power socket and bulk head fittings) on surface wiring on wooden batten/casings & caping complete, including fixture and fittings such as switches, ceiling roses,pendents holder, regulators and sockets by unscrewing carefully from boards etc and making good disturbed surfaces of walls, as per existing finishes complete all as spd and directed.

M & L for point wiring for one light/one fan controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS cable with and including PVC concealed conduit heavy duty 20 mm dia having thickness not less than 1.8 mm with all fittings including anodise pressed steel sunken box having thickness not less than 2mm with 3mm bakelite laminated sheet ISI marked for switches and sockets , including 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor connected to comman earth dolly, including cutting chiseling for concealed piping and making good disturbed surface to match with the existing surface complete all as specified and directed.Note: (a) Insulation test of point wiring (b) colour coding is to be maintained .(Ph-Red, N-Black, Half -Yellow, Earth- Green) (c) On RCC roof ceiling PVC conduit shall be provided on surface for fan with proper fixing clips all as directed.

All as per srl item No 101 here-in-before but for 5 pin 5 amps socket outlet on independent board complete all as specified and directed.

All as per srl item No 101 here-in-before but for 3 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed.

M & L for point wiring with 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS cable with in and including PVC concealed conduit heavy duty 20mm dia having thickness not less than 1.8 mm with all fittings including anodise pressed steel sunken box having thickness not less than 2mm with 3mm bakelite laminated sheet ISI marked suitable for 5 pin 15 amps socket outlet ,including 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor connected to comman earth dolly in and including cutting chiseling for concealed piping and making good disturbed surface finishing the surface to match with the existingsurface complete all as specified and directed.Note: (a) Insulation test of point wiring (b) colour coding is to be maintained .(Ph-Red, N-Black,Earth- Green)

S & F switch piano flush type one way 5 amps SP 240 volts complete all as specified and directed.

S & F switch piano flush type one way 15 amps SP 240 volts complete all as specified and directed.

S & F socket outlet 2 in 1, 3 pin 5 amps flush type 240 volts complete all as specified and directed.

S & F socket outlet 2 in 1, 3 pin, 5 and 15 amps flush type 230 volts complete all as specified and directed.

S & F lamp holder/batton holder/angle holder insulated body with bakelite back plate suitable for fittings complete all as specified and directed.

S & F ceiling rose 65 x 50mm three terminals complete all as specified and directed.

S & F in replacement Modular Bell push 6A 1 module , complete all as specified and directed.

S & F in replacement Modular switch 1 way 6 A, 1 module complete all as specified and directed.

S & F in replacementModular switch 1 way 16A, 1 module complete all as specified and directed.

S & F in replacement Modular Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed.

S & F in replacement Modular Socket, 6A - 2/3 pin combined 2 module complete all as specified and directed.

S & F in replacementof Modular Fan regulator 6A 1 module , complete all as specified and directed.

S & F in replacement of Modular White cover plate with frame, 3 module, complete all as specified and directed.

S & F in Replacement of Modular White cover plate with frame, 4 module, complete all as specified and directed.

S & F in replacement of Modular White cover plate with frame, 6 module, complete all as specified and directed.

Supply and fixing ceiling fan regulator electronic socket type 5 stage speed variation ISI marked complete all as specified and directed.

S&F in replacement existing UNSV sleek LED mirror light fitting 2 feet long 1x10 W including LED tube 2 feet long having ballast, bipin holder, connector block etc complete all accessories prewired and connecting electrically to ceiling rose usning PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as directed by Engr-in-chagre

S & F in replacement of CFLs with LED smart Lamp, B22 type ,14 watt,complete all as specified and directed.

Supply and Fix in replacement existing UNSV tube light fitting with LED 20W inverter batten type fitting 4 feet long aluminium extruded housing, charging time 10-12 hours and back up time 04 hours, IP-20 ,rated voltage 230 V, 50 hz, system wattage 20W +/- 10%, system current less than 102 mA, power factor more than 0.95, system lumen efficiency 100lm/watt,CCT 6500K, CRI more than 80, THD less than 30%, driver efficiency more than 85% complete all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site or directed. Notes: (i) LM79 report from third party (instead of company in house lab) NABL/UL accredited lab (ii) LM 80 report from LED manufacturer (iii) Test certificates to be submitted before commencement of work/ claiming for payment . (iv) Warranty certificate for minimum 2 years to be submitted from OEM.

M & L for providing/ cutting the round/ square hole of required size in wall finishing the same for distrubed surfaces complete all as spd and supply and fixing propeller type AC ventilating fans, Single phase, 230 volts 300 mm sweep H.D EX Fan (900 RPM) complete and supply and grouting the ragged bolts in wall, fixing the frame on the exhaust side (outer surface of the wall) and connecting with and including PVC insulated three core 1.5 sqmm copper cable from ceiling rose to exhaust fan motor and writting MES No. with black synthetic enamel paint 2.0 cm high complete all as specified.

M & L sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 12 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification .

M & L sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 06 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification .

M & L sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 04 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification .

M & L sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 02 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification .

M & L sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 08 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification .

M & L MCB Single Pole 240 volts any rating from 20 to 40 amps, with rupturing capacity 10 KA, including providing thimble for out going cables.

M & L MCB SPN 240 volts any rating from 6 to 40 amps, with rupturing capacity 10 KA, including providing thimble for out going cables.

Supply and laying in replacement of existing unserviceable/ burnt submain wiring alongwith two single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of size 6 sqmm drawing into and including concealed PVC rigid non metallic conduit of 20mm dia , 1.8 mm wall thickness and single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of 6 sq mm as earth wire including cutting chases in brick wall, rendering in cement mortar 1:4 and making good the disturbed surfaces to match existing complete all as specified & directed. Note: (i) Two runs of 6 Sqmm single core PVC insulated copper conductor cable(FRLS) and one run of 6 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of 20mm dia , 1.8 mm wall thickness wiil be measured as a one unit. (ii) Proper colour coding is to be followed as per IS Specification. (iii) Test certificates of cables to be submitted before commencement of work/ claiming for payment. (iv) wiring shall be concealed/ on surface with rigid PVC conduit medium grade as per site requirement. (v) Electric Wiring test sheet before and after completion of wiring to be submitted before claiming payment

Supply and laying in replacement of existing unserviceable/ burnt submain wiring alongwith two single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of size 4 sqmm drawing into and including concealed PVC rigid non metallic conduit of 20mm dia , 1.8 mm wall thickness and single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of 4 sq mm as earth wire including cutting chases in brick wall, rendering in cement mortar 1:4 and making good the disturbed surfaces to match existing complete all as specified & directed. Note: (i) Two runs of 4 Sqmm single core PVC insulated copper conductor cable(FRLS) and one run of 4 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of 20mm dia , 1.8 mm wall thickness wiil be measured as a one unit. (ii) Proper colour coding is to be followed as per IS Specification. (iii) Test certificates of cables to be submitted before commencement of work/ claiming for payment. (iv) wiring shall be concealed/ on surface with rigid PVC conduit medium grade as per site requirement. (v) Electric Wiring test sheet before and after completion of wiring to be submitted before claiming payment

S & F in replacement of old unsv sheet metal enclosures distribution boards, double door three phase 415 volts 4 ways vertical TPN DB for comprising three phase four wire copper strip bus bar of appropriate capacity complete all as specified and directed and comprising of the following (a)MCCB FOUR POLE 100 AMPS AC 415 VOLTS 25 KA=01 NO as incoming and including 12 nos. MCB SP 40 Amps, C series as outgoing (Note :- (i)The DB shall be VTPN series of Schenieder Cat Part No:- A9HVD04L or equivalent in any of the make mentioned in list of product . (ii) The DB shall be flush fixed ,and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost.(iii)connection of theMCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble -properly crimped.(1v) all the vacant holes of the DB shall be provided with blank plates of appropriate size. (v) double continuous earth wire shall be provided for each three phase DB from earthing mains dolly (vi)MCCB's and MCB's should have a same make as of DB.

S & F bldg secuirty light fitting energy saving high efficiency LED street light fitting 25 Watts, 5700 K, IP 66, having pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, prismatic polycarbonate cover complete including GI bracket of size 32 mm dia bent to shape having length on less than 1.5 mtr fixing with clamp etc and making connections using cord flexible 3 core copper cable of size 23/ .0076 from ceilling rose/ PVC connector to light fittings or as directed by Engr-in-chrage. Notes :- (i) Contractor shall produce LM79 & LM 80 test report from OEM owned NABL accredited laboratory. (ii) Contractor shall give guarantee/ warranty of complete fitting/ fixture for minimum 2 years from the date of completion. (iii) Contractor shall conduct the inspection of company representative at site before installation of the material at no extra cost. (iv) Contractor shall arrange complete material at site for approval of GE before incorporation in the work. (v) Driver shall be IP 66 degree of protection potted seal type with inbuilt SPD and external SPD of capacity 10 KV to be provided in addition to inbuilt.

Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, surrounded on all sides by alternate layers of 150 mm thick charcoal and common salt, connected to galvanized earh lead wire of size 4.0 mm by means of lugs, bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3 of SSR Part I, wire protected by dia 15 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI medium grade including wire mesh funnel, PCC, earth chamber pit with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame, necessary excavation and earth work in any type of soil including testing on completion for desired result all as specified. Note: The rate quoted include cost of 7.5 metre earthing wire with protection pipe.

Supply & Fixing in replacement of Socket outlet 2 in 1, 3 pin, 5A complete in existing circuit complete as directed buy Engr-in-charge.

Supply & Fixing switch piano flush button single pole one way 5 Amp 230 volts in existing circuit as directed buy Engr-in-charge.

Supply and Fixing in replacement of socket outlet 2 in 1, 3 pin, 5 and 15 amps flush type 230 volts complete all as specified and directed.

Supply and Fixing in replacement of switch piano flush type one way 15 amps SP 240 volts complete all as specified and directed.

Supplying & Fixing in replacement of Switch Bell push, flush type, 5 amp one way complete all as specified and directed by Engr-in-charge.

S&F in replacement of Buzzer Ding Dong, AC 230 Volts single Phase complete all as specified and directed by Engr-in-charge.

S & F lamp holder/batton holder/angle holder insulated body with bakelite back plate suitable for fittings in existing circuit complete all as specified and directed.

Supply and Fixing in replacement LED Bulkhead fitting 10 watt all as specified and directed by Engr-in-charge. Make :- Crompton Cat Part No:- LBHP-10-CDL or equivalent to Halonix/Havell's.

S&F in repair Hylum sheet 100 x 100 mm for fixing of switchs sockets including cutting for switch socket and fixing to existing sunken box with brass screw complete all as specified and directed by EIC

S&F in repair Hylum sheet 100 x 150 mm for fixing of switchs sockets including cutting for switch socket and fixing to existing sunken box with brass screw complete all as specified and directed by EIC

S&F in repair Hylum sheet 150 x 250 mm for fixing of switchs sockets including cutting for switch socket and fixing to existing sunken box with brass screw complete all as specified and directed by EIC

S&F in repair Hylum sheet 200 x 250 mm for fixing of switchs sockets including cutting for switch socket and fixing to existing sunken box with brass screw complete all as specified and directed by EIC

Supply and fixing one single core 1.5 Sqmm nominal cross sectional area multistrand copper conductor cable PVC insulated unsheathed 1100 Volts grade earth wire complete all as specified and directed

Supply and fixing one single core 2.5 Sqmm nominal cross sectional area multistrand copper conductor cable PVC insulated unsheathed 1100 Volts grade earth wire complete all as specified and directed

S&F in replacement of old unsv wooden box with PVC switch box with sheet cover surface/ concealed 100 x 100 x 50 mm for switch socket and regulator including cutting for switch & regulator and fixing to existing sunken box with screw with one washer complete all as specified and directed by EIC

S&F in replacement of old unsv wooden box with PVC switch box with sheet cover surface/ concealed 150 x 150 x 50 mm for switch socket and regulator including cutting for switch & regulator and fixing to existing sunken box with screw with one washer complete all as specified and directed by EIC

Notes : The Schedule of Credit amount shall be deducted from the total of this schedule(BoQ) to arrive at Contract Sum.

VIKRAM SINGH MANHAS

GANDOTRA CONSTRUCTION CO

AGGARWAL ASSOCIATES

Abrol brothers and company

M/S SALARIA BUILDERS

satpal and brothers

M/S Raghuvanshi Builders

kailu construction co