REPAIR MAINTENANCE OF FLOORING WALL PANELLING FALSE CEILING BRICK WORK POLISHING TO KOTASTONE CUPBOARD AND ALUMINIUM WORK SANITARY PLUMBING AND CERTAIN B R WORK AT SEWAR FORT AND PARADE GROUND BHARATPUR MIL STN

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc complete all as specified.

M & L rendering 15 mm thick in CM (1:4) on fair faces of brickwork or concrete surfaces finished even & smooth without using extra cement complete all as specified.

All as above item No. 2 but in CM (1:6) on other than fair faces finished even and smooth without using extra cement complete all as specified.

M&L for rendering 10mm thick in cement mortar 1:4 on concrete surfaces including finished even & smooth without using extra cement on ceiling including taking down plaster complete all as specified.

M&L for one coat of exterior emulsion paint on old treated surfaces of walls, white or tinted including preparation of surfaces complete all as specified.

M & L Preparation of new decorated plastered surfaces of wall including cornices, pilasters etc by brooming down and applying two coats of cement base paint of approved shade on walls with hand roller complete all as specified.

M & L Preparation of new plastered surfaces of wall including cornices, pilasters etc by brooming down and applying Three coats of white wash on walls complete all as specified.

M & L Preparation of new plastered surfaces of wall including cornices, pilasters etc and applying two coats of oil bound distemper over a coat of primer and 2mm wall care putty of approved shade on walls by roller complete all as specified.

M&L for three coats of white wash on new plastered surfaces of Ceilings including prepration of surfaces complete all as specified.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoin jambs pillars etc complete all as specified.

M&L Brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified.

All as above item No. 11 but except bricks

Demolition of PCC in ground floors and pavings not exc 15cm thickness ( below or above ground level ) complete all as specified.

M&L for PCC 1:3:6 type C1 using 20mm graded stone aggregate as in plinth protection, 50mm thick finished even and smooth without using extra cement complete all as specified.

M&L for PCC 1:2:4 type B1 using 20mm graded stone aggregate as in flooring 40mm thick finished even and smooth with using extra cement complete all as specified.

Supply only glass dividing strips 3mm thick and 38mm wide & fixed in position complete all as specified.

M&L for coloured Non Skid Ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm , over 10 mm thick screed bed in CM 1:4 in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

M&L for Coloured Non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm bur not exceeding 0.38 sqmm, over 10 mm thick screed bed in CM 1:4 in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified.

M&L for Vitrified Light Shade ceramic tiles 10 mm thick (Square/rectangular) area of each tile not exceeding 0.36 sqm ,over 10 mm thick screed bed in CM 1:4 in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ), removing serviceable tiling to store and rubbish off the premises complete all as specified.

Dismantling of stone slab and tiles of any description or thickness in floors, etc laid beded and pointed in any mortar complete all as specified.

M&L for Granite (of any type) tiles/slab in skirting/dados 20 mm thick laid over and including cment screed and 15 mm thick cement mortar 1:3, laid and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including rubbing and polishing complete all as specified.

M & L for Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified.

M&L for Machine cut kota stone slab flooring 20-25 mm thick over cement screed 20 mm thick in cement mortar 1:6, laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for Machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dedo and pillar laid over cement screed 15 mm thick in cement mortar 1:4, laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

Cutting, polishing to existing Kota/ marble flooring,(three cuttings and mirror polishing) including levelling certain places to Kota/ marble floor ,necessary repair work complete all as specified.

Cutting,Scrubbing,Rubbing, polishing to existing Terrazo (Mosaic or Marble) flooring ) ,including removing mild water stains,organic spill stains ,scratches ,other marks & levelling certain places to floor ,necessary repair work complete all as specified.

Taking up or down the existing unserviceable GI pipe and M&L for new galvanised steel water tubing medium grade ISI marked with all fittings and fixed complete to walls and ceilings or laid in floors of following sizes :-

(a)15 mm bore

(b)20 mm bore

Taking up or down old serviceable GI pipe Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, trenches etc ) including cleaning of following sizes.

(a)15 mm bore

(b) 20 mm bore

S&F in repairs bib tap, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of 15 mm bore complete all as specified.

S&F in repairs stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed of following size

(a)15 mm bore

(b) 20 mm bore

S&F in repairs brass ball valve of 20mm bore, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed complete all as specified.

S&F in repairs brass ball valve of 25mm bore, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified.

Dismantling existing water tank of capacity exc 250 ltrs & n. exc. 500 ltrs and S &F of Rotational moulded polyethylene water storage tanks 500 Ltr (cylinderical vertical with closed top)with 20mm dia ball brass valves,high pressure , with polythene float and flynut complete, hoisted and fixed in position complete all as specified in SSR part - I.

S & F in repair of vitreous china squatting pan, 'Orissa' pattern, size 580x440 mm white, with integral foot rests, 'P' or 'S' trap, including connection to trap, and to flushing pipe, anti-syphonage pipe etc. complete including making good to floor with PCC/ Lime concrete bedding complete all as specified.

S&F in repair of pillar tap, cast copper alloy with capstan heads,chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore complete all as specified.

S&F in repair vitreous china wash hand basin, white, of size 550x400mm flat back excluding taps, chain and plug but including waste pipe, brackets, cutting for and pinning in ends of brackets or erecting stand complete all as specified.

S&F waste fitting brass chromium plated for 32mm bore with long screwed shanks and fly nuts including 32mm PVC waste pipe for WHB complete all as specified.

S&F reflection mirror range of size 80X60 cm alongwith all necessary fitting and fixtures etc complete all as specified.

S&F in repair half turn flush cock of brass of 25 mm bore complete all as specified.

S&F in epair MS chromium plated grating 125mm dia of weight not less than 50gm for floor trap / Nahani trap complete all as specified.

S&F in repair of brass chromium plated shower rose 125mm size with swivel joint type including fixing to steel pipe of 15mm bore or union complete all as specified.

S&F in repair of PVC low level flushing cistern 10 ltrs capacity with inlet ball valve float & handle, syphonic action type including brackets & flush pipe of polythelene of low or high level 32mm dia complete all as specified.

S&F in repair of aluminium anodised tubular towel rail, 20mm dia, 'D' type, 60cm long between flanges complete all as specified.

S & F in repair of cast iron nahani trap of 75mm bore, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified.

S&Fin repair of 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, ISI marked complete all as specified.

S&Fin repair of 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, ISI marked complete all as specified.

S&Fin repair of 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, ISI marked complete all as specified.

Taking down chowkats or frames n. exc 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified.

Taking down shutter of any description area exc 1 sqm and n. exc 2 Sqm each complete all as specified.

Taking down chowkats or frames exc. 1.5 sqm but not exc. 4 sqm each without taking off shutters from frames complete all as specified.

S&F 35 mm thick 2nd class hardwood factory made plain framed, panelled shutters (any No. of panels) with lock rail and panel of 9mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces size of members as per IS 1003 PtI complete all as specified.

S&F 35 mm thick 2nd class hardwood factory made glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc.( without sash bars ), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauge etc., sizes of members of shutters complete all as specified.

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, door chowkats of angle or other section and similar works complete of Gde Fe-290 Gde E-165 including welding etc complete all as specified.

S&F MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Fe-290 Gde E-165 including necessary welding etc. and fixed in position complete all as specified.

S & F Factory made steel window with side hung shutteers including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded complete all as specified.

All as above item No 57 above but without glazing bars.

S&F Sheet glass ordinary quality 3 mm thick and glazing with oil putty in square n. exc 0.50 sqm in each pane complete all as specified.

Hacking out old broken glass any thickness, size, quality or description from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads including S&F 3 mm thick plain sheet glass ordinary quality in square not exceeding 0.5 Sqmm each pane complete all as specified.

Galvanised mild steel wire cloth 0.50 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified.

All as per item No 61 above but in repairs complete all as specified.

S&F both side laminated particle boards19 mm thick medium density, flat pressed, single , layer type or three layer type BWR type adhesive, fixed with beading/screws to timer frame/metal frame as in shutters, shelving to cup boards etc complete all as specified.

S&F steel ventilator with top hung shutter including hinges,steel peg stay, handle complete all as specified.

M&L for cutting opening in cement concrete walls (any description) for door, window and other openings(with or without reveals) or enlarging existing openings, including trimming surfaces to receive rendering etc. with or without reinforcement complete all as specified.

S&F 100 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkats including welding complete all as specified.

S&F 50 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkats including welding complete all as specified.

S&F150 mm long mild steel barrel tower bolts stove enameled black with bright bolt (ISI marked) complete all as specified.

S&F Mild steel pressed steel bow handle oval type stove enameled black of size 150 mm (ISI marked) complete all as specified.

S&F Small fitting such as brackets of any type latch and hinge blocks shapped door and window stops and the like n. exc 200 cu cm of second class hard wood including all necessary labour complete all as specified.

S&F MS sliding door bolt, plate type, 300mm long, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts & nuts, 4 on bolt plate and 2 on staple plate and fixed complete all as specified.

S&F in repair of mild steel 300 mm, ordinary rat tail rod pattern including roller and roller plate fixed to wooden/ angle iron chowkats complete all as specified.

S&F in repair of 25 mm thick flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides all as specified and 3mm thick veneering on both face including french polish in two coat and teakwood lipping on edges of shutters complete all as specified.

S&F hasp and staple of size 100 mm aluminium anodised safety type with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified.

M & L for Painting to new untreated steel surfaces of any description over 10 cm in width or girth with two coats of synthetic enamel paint over a coat of Zinc chrome primer including preparation of surfaces complete all as specified.

M&L for preparation of new untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

S&F for sollid PVC door frame of size 50mmx47mm made out of 5mm plain colour pvc sheet reinforced with m.s. squre tube complete all as specified.

Supplying & fixing in the frames at site factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as specified and shown on SSR 2020 (Part-II).

S&F extruded aluminium alloy handle 150mm size fabricated type anodised, ISI marked complete all as specified.

S&F Aluminium anodised barrel tower bolt 150mm long of extruded section and fixed complete all as specified.

S&F 75 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkats including welding complete all as specified.

S & F powder coated Anodised Aluminium frame for door,windows,vantilators with one or more rebates including joining cleats for fixing etc complete all as specified.

S & F powder coated Aluminium door shutter,aluminium section weighing 0.55kg/m including necessary joining cleats glazing clips,rubber neoprene packing aluminium handles 2 Nos in each door,hinges aluminum 100mm size 03 Nos anodized aluminium snap beading screw etc complete all as specified.

S&F powder coated Anodised aluminium window and ventilators shutters,side hung type without sash bars,aluminium section weighting 0.55 kg/m including necessary joining cleats,glazing clips,rubber packng,anodised aluminium snap beading,screws,anodised aluminium fitting such as peg stays 150mm long 1 nos ,hinges type B-21 100 mm long 02 Nos suitable handle 01 Nos complete all as specified.

S&F in repair/Replacement double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box,main body with stainless steel cover,governing pivot made of brass,other parts made of mild steel heavy duty and fixed complete all as specified.

S&F in repair Aluminium extruded section body door closer hydranlically regulated designation no 3 universal type suitable for door shutter up to 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified.

Demolition of cement concrete (unreinforced ) of roof , any description complete all as specified.

M&L for 40mm thick PCC type B-1,( 1.2.4) using 20 mm graded stone aggregate as in roof finished even & smooth without using extra cement complete all as specified.

M&L for screed bed or bedding layer 15 mm thick in cement mortar 1:4 mixed with water proofing compound as per manufacturer's instruction, finished even and smooth without using extra cement over cement slurry over existing roof @3 kg/sqm . WPC Shall be meashured and paid seperatly complete all as specified.

Supply only water proofing compound ISI marked complete all as specified.

M&L APP based polymeric membrane not less than 3mm thick , weighing not less than 3.5 Kg / sqm , and upper side of membrane thermally insulated with white mineral gravel finish , informly embedded during manufacturersprocess,shall only be used . It shall be laid by torch application .Side over laps shall be 75 mm and the end lap shall be 100 mm and all overlaps and joints shall be sealed by torch application including applying a coat of cold applied bitumen primer conferming IS:3384 @0.40 Kg/Sqm complete all as specified.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation, boards/slabs/blankets, any thickness, including cover fillets and frame work complete all as specified.

S&F PVC wall panelling with panel of 300 mm x 6 mm Hollow section of Sintex pattern SPUF- 146 or equivalent , fixed with PVC plug and screw and inserted to next panel groove, edges and corners of all door/ window/openings etc to be covered with PVC angle fixed with solvent cement complete all as specified.

M&L for providing and fixing Gypsum Board 12 mm thick in ceiling fixed with screws as per manufacturers instructions complete all as specified.

S&F anodised aluminium snap grid frame work of size 605x605mm for false ceiling complete all as specified.

S&F hangers 6mm dia. G.i. (up to 1200 mm length ) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40x3mm size 60 mm long and hold fasterners 12.5mm dia 40mm long.complete all as specified.