ROOFING & FALSE CEILING WORKS OUTLETS UNDER SZ RE

DISMANTLING,FALSE CEILING — "Dismantling of all types of ceilings except of bk work/CC, sheets like AC, TRAC, GYPSUM BOARD etc. Scope of job includes handing over of all 'J', 'L' hooks, nuts and bolts, suspendors or other joineries in proper bags. Party to ensure joint measurement of the job to be dismantled, alongwith EIC, before start. Payment shall be made basis the joint measurement, in absence of any joint measurement record HPCL EIC decision shall be final.

REMOVAL OF ROOFING — REMOVAL AND STACKING OF THE EXISTING CANOPY ROOFING MATERIAL AND ROOFING SYSTEM AND STACKING THE REMOVED ROOFING MATERIAL MATERIAL AT UNOBJECTIONABLE PLACE AT THE RETAIL OUTLET AS DIRECTED BY THE EIC AND THE CONSULTANT. THE MATERIAL REMOVED FROM THE EXISTING CANOPY TO BE STACK PROPERLY WITH INDEXING THE MATERIAL GOOD FOR INSPECTION.

DISMAN OF EXISTING GUTTER 7049-CHENNAI RETAIL RO — DISMANTLING AND REMOVING OF EXISTING GUTTERS. CARE SHOULD BE TAKEN FOR NOT DAMAGING THE EXISTING SHEETS AND STRUCTURE. REMOVING AND SHIFTING OF THE REMOVED MATERIAL AS PER INSTRUCTION OF ENGINEER-IN-CHARGE.

SUP & INST - FASCIAGI,THK:20 7049-CHENNAI RETAIL RO — SUPPLYING AND FIXING 20 SWG GI SHEET FACIA INCLUDING PAINTING WITH ONE COAT OF ZINC CHROMATE PRIMER AND TWO COATS OF 1STQUALITY SYNTHETIC ENAMEL PAINT ON FRONT SIDE . NECESSARY FACIA FRAMEWORK FOR FASTENING THE SHEET TO THE CANOPY SECURELY SHALL BE PAID SEPARATELY.

SPLY AND FIXG OF GUTTER — PROVIDING AND FIXING 20G ALUMINIUM GUTTER SUITABLY BENT WITH PROPER OVERLAPS, SEALANT, REVET, SCAFFOLDING, LABOUR, TRANSPORTATION, ETC, COMPLETE.

SPLY AND INSTLN OF — PROVIDING AND INSTALLING ROOFING RIBBED ROOFING SYSTEM MANUFACTURED WITH HIGH STRENGTH STEEL GRADE OF G550(550MPA) OF HPCL APPROVED BARE GALVALUME HIGH TENSILE COLD ROLLED STEEL AS PER ASTM 117 A792M/AS 1397 COATING CLASS AZM 150 (MINIMUM 150 GM/SQM ZINC-ALUMINUM ALLOY COATING MASS TOTAL OF BOTH SIDES), OF YIELD STRENGTH 550 MPA THICKNESS OF BARE METAL (BCT): 0.40MM,TOTAL COATED THICKNESS(TCT) : 0.45 MM .APPROXIMATE MASS OF ROOFING SHEET SHALL BE 4.17 KG/SQM. PANELS SHALL BE OF MIN. 900 MM WIDE AND MIN. CORRUGATION DEPTH OF 38 MM WITH VARYING LENGTHS AS PER SITE REQUIREMENTS RATE SHALL BE INCLUDING LAYING OF SHEETS WITH APPROVED FASTENERS AND ALSO ALL WEATHER SEALANT TAPE AS PER MFR''S RECOMMENDATIONS AND ALSO PROVIDING RIBBED GALVALUEME RIDGE PIECES OF THE SAME CLASS AS OF THE MATCHING CORRUGATION PROFILE OF THE ROOFING SYSTEM AS RECOMMENDED BY THE MFR.AND, HORIZONTAL/VERTICAL FLASHING NEAR ILLUMINATED BANDING .

PROVIDING&FIXING,FALSE — "Providing & fixing false ceiling system of Trac 150 F exterior grade or approved equivalent of 0.5mm thick galvanised steel with stove enameled coil coated finish inter locking ceiling panels, carriers, suspension system and edge closure as per the following specification. Supplying and installation of exterior grade 150 F ceiling system comprising of 150 mm x 17 mm deep panels roll formed out of 0.5 mm galvanised steel with stove enameled coil coated finish. The panels shall be pre-treated and coil coated on one side in manufacturers standard colour shades as approved by the Architect/ Engineer in charge. The rear side of the panel shall be given a coat of primer and a wash coat while the finished side shall be given a coat of primer and finish colour coat in polyster paint for a min. dry film thickness of 20 microns, fixed on to the roll formed carriers 34.5 mm x 488 mm deep out of 6 mm thick Galvanised steed with prongs to hold panels in the module of 150 mm at maximum 1.2 mts. C/C. The carriers to be suspended from roof truss by rigid suspension angles as per manufacturer's recommendation. Panels shall be supplied in custom length upto maximum of 5 mts. Job also includes providing ceiling flashing using factory formed 0.5 mm thick Polyster coated galvanised steel material. Rate shall be including providing flashing to cover gap if any between illuminated banding and false ceiling.

PAINTING OF CANOPY COAT:2 7049-CHENNAI RETAIL RO — PAINTING OF CANOPY, CLEANING OF THE CANOPY FASCIA AND FALSE CEILING SURFACE TO REMOVE ANY OBSERVED RUST AND PROVIDING AND APPLYING 2 COATS OF SYNTHETIC ENAMEL PAINT 1ST QUALITY OF APPROVED MANUFACTURER AND SHADES ON THE SURFACE TO GIVE AN EVEN SHADE AFTER TWO COATS OF RED OXIDE PRIMER AS PER IS-712 LATEST REVISION. THE COLOUR SCHEME SHALL BE AS PER STANDARD HPCL COLOUR CODING.

INST SUPPLIED FIXT CAN OR — TO INSTALL SUPPLIED LED FIXTURE OF CANOPY OR YARD LIGHT AT RETAIL OUTLETS OR OTHER PREMISES AS DECIDED BY HPCL. WORK INCLUDES PICKING UP OF FIXTURES, ACCESSORIES, CUT OUTS, CONTROLLERS ETC. FROM REGIONAL OFFICE, TRANSPORTING, STOCKING AT RETAIL OUTLETS. COST TO INCLUDE INSTALLATION OF FIXTURE AS PER MANUFACTURER RECOMMENDATION, WITH CHAIN OR GI WIRE HOLDING STRAPS, ACCESSORIES, MATERIAL, LABOR ETC.. VENDOR TO FOLLOW INSTRUCTIONS OF EIC FOR DECIDING THE LOCATION OF FIXTURE. CABLE, GLANDS WILL BE PAID EXTRA IF PROVIDED BY VENDOR.

SPLY&TRANSPT OF LIGHT — SUPPLY AND TRANSPORTATION (TO RESPECTIVE ROS/YARD AS MENTIONED IN THE TENDER DOC) OF 80 W CANOPY LED LIGHT FIXTURE WITH MIN 140 LUMENS PER WATT EFFICACY FOR LEDS AND MIN 120 LUMENS PER WATT EFFICACY FOR THE SYSTEM. KINDLY READ THE DETAILED TECHNICAL SPECIFICATIONS AS PER THE ATTACHMENT.