Provision of Infrastructure to set up Scientific Laboratory in Room No 28 of CERS Building at DEAL Raipur Road Dehradun

Amount

Composite Works

Providing and fixing cup board shutters 25 mm thick, with Pre-laminated flat pressed three layer particle board or graded wood particle board IS:12823 marked, exterior grade (Grade l Type ll), having one side decorative lamination and other side balancing lamination, including IInd class teak wood lipping of 25 mm wide x12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete all as Spd and as per direction of the Engineer-in-Charge

Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x1.6 mm hollow MS tube, placed along the walls, ceiling and floor in a grid pattern with spacing @ 60 cm centre to centre both ways (vertically & horizontally) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete complete all as Spd and as per direction of the Engineer-in-Charge

Providing and fixing Pre-laminated medium density fibre board18 mm thick confirming to IS: 14587:1998 marked, with one side decorative lamination other side balancing lamination Grade-I(exterior grade) in shelves with screws and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand (fittings to be paid separately). complete all as Spd and as per direction of the Engineer-in-Charge

Providing and fixing in wall lining flat pressed three layer (medium density) 25 mm thick particle board or graded wood Pre-laminated with one side decorative lamination and other side balancing lamination Grade I, Type II, IS : 12823 marked, including priming coat on unexposed arrangement and screws etc. complete

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-Charge (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts bolts/ fasteners etc.). complete all as Spd and as per direction of the Engineer-in-Charge

Providing and fixing special quality bright finished brass cupboard or ward robe of size 50 mm locks with four levers of approved quality including necessary screws etc. complete all as Spd and as per direction of the Engineer-in-Charge

Providing and fixing 50 mm bright finished brass cup board or wardrobe knob of approved quality with necessary screws complete all as Spd and as per direction of the Engineer-in-Charge

Providing and fixing 100 long bright finished brass handles with screws etc. complete all as Spd and as per direction of the Engineer-in-Charge

Providing and fixingTriple strip vertical type magnetic catcher of size not less than 50 mm of approved quality in cupboard /ward robe shutters, including fixing with necessary screws etc. complete all as Spd and as per direction of the Engineer-in-Charge

Providing and fixing powder coated telescopic drawer channels 300 mm long width not less than 45 mm with necessary screws etc. complete all as Spd and as per direction of the Engineer-in-Charge

Providing and fixing sliding arrangement in Racks/ Cupboards / Cabinets shutter by with stainless steel rollers to run inside C or E aluminium channel section (The payment of C or E channel shall be made separately) complete all as Spd and as per direction of the Engineer-in-Charge

Providing and fixing 100 mm long bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete all as Spd and as per direction of the Engineer-in-Charge

Stainless steel silver concealead pie cut hinges , width between two hinge cup-48 mm& hole distance on mounting plate -32 mm for cabinet complete all as Spd and as per direction of the Engineer-in-Charge

Providing and fixing Powder coated (minimum thickness of powder coating 50 micron) aluminium section work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free,straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, (Glazing, paneling and dash fasteners to be paid for separately) complete all as Spd and as per direction of the Engineer-in-Charge

Providing and fixing cup board shutters with 18 mm thick veneered particle board IS : 3097 marked, exterior grade (Grade I), of approved make, including IInd class teak wood lipping of 25 mm wide x 12 mm thick with sunmica top1.0 mm with necessary screws and bright finished stainless steel piano hinges, complete all as Spd and as per direction of the Engineer-in-Charge

Supply of coffe table (Splenda coffee table of size 120 cmx 60 cm x40 cm top MDF board of grade E1 ( Environmental Friendly) covered with melamine 25 mm thick, table top edge banded with PVC tape 2.0 mm ,chrome base stainless steel grade 304 under structure of table,frame size 100x50 mm & leg size75 x50 mm complete all as Spd and as per direction of the Engineer-in-Charge ( Godrej Interio/ Durian/ Methodex)

S& F (Splenda corner table) corner table of size 53cmx 45cm x45.8 cm top material medium density fiber board 18 mm thick with glossy finish, teak wood frame 75x25 mm, table top edge banded with PVC tape 2.0 mm and leg size 50 x50mm complete all as Spd and as per direction of the Engineer-in-Charge ( Godrej Interio/ Durian/ Methodex)

Providing wood work in frames of doors, windows, clerestory windowsand other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Second class teak wood complete all as Spd and as per direction of the Engineer-in-Charge

S&F Anti static rubber mat in two layer good quality 3 mm thick class B resistant to alkali & oil & low temprature complete all as Spd and as per direction of the Engineer-in-Charge

S& F Vertical Venetian blind any colour or size for window curtain 100 % woven polyster or polymer coated glass fibre high quality, 100 mm slat width including opening & closing head rail mechanism, top & bottom cord as approved complete all as Spd and as per direction of the Engineer-in-Charge

Supply office revolving chair with arm advanced bio synchronic high back rest, seat material pu foam covered with fabric, mesh fabric at back all with the following Specification - Pedestal Base - Aluminium die cast with ABS/Nylon Twin Caster Wheels minimum 5 Nos, of 50 mm size Arm Material - Aluminium covered with PU Seat Material - PU foam 50 mm covered with 100 % Polyster fabric having density 45 Kg /cum GSM/ Thickness of fabric - 250gram/sqm Height Adjustment - Up to 100 mm Type of back rest Support - back rest with adjustable lumber support Colour - As approved Type of Locking - 5 Position locking Diemension - 1080 mm (height), Backrest height (600 mm) Seat height (450mm), Seat width ( 500 mm) ( Godrej Interio-ACE High back Chair/Methodex- ZEPHYR high back/Sterling - ARISTO-HB) complete all as Spd and as per direction of the Engineer-in-Charge

Supply office executive mid back chair with arm medium back rest,seat material PU foam covered with fabric, back mesh with PP structure revolving pedestal with following specification Pedestal Base - Aluminium die cast with ABS/Nylon Twin Caster Wheels (Min) 5 Nos, of 50 mm size Arm Material - Aluminium covered with PU Seat Material - PU foam 50 mm covered with 100 % Polyster fabric having density 45 Kg /cum Width - 72.5 cm,depth 72.5 cm Seat height- 46 - 54.5 Cm Height - 100.5-109.0 Cm Height Adjustment- Multi -Position lockable synchro -tilt mechanism Colour - As approvrd Upholestry - Net fabric lumber support - Two way adjustable support (Godrej Interio- model No Leoma MB(9M02A)/Delite Mid Back Ergonomic Fonzel/Methodex- ZEPHYR MB complete all as Spd and as per direction of the Engineer-in-Charge

Supply of 5 seater sofa set (3+1+1) primary material leatherette with following specification Frame Material - Soild Wood Primary Colour - As approved Upholestry material - Leatherette Diemension - one seater- width 92 cm , height 73 cm, depth 87 cm Three Seater - Width - 175 cm, height 73 cm, depth - 87 cm (Godrej Interio-PARTO/ Royal Oak - Barcelona/Durian-Blos,Matt finish Pebble Beige)complete all as Spd and as per direction of the Engineer-in-Charge

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade Two or more coats on new work complete all as Spd and as per direction of the Engineer-in-Charge

Supply , installation,commisionig and testing high wall Split Type Air Conditioner, 2TR/ 6000 kcal/hr, copper coil material, compressor speed inverter type ( veriable speed), with hot and cold provision, comlete with indoor & out door assembly charged with refrigerant, suitable length of refrigerant tubes and power cable, fixing arrangement, brackets etc for mounting arrangement and 20 MM PVC conduit suitable as outlet for condensate drainage water from indoor unit etc as directed by Engr-in-charge. Make: DAIKIN, Model-FTHP60 (daikin)Daikin & FTHP60SRV16./Voltas (24HSZS)/ Amstrad (AM2013HC).complete all as Spd and as per direction of the Engineer-in-Charge

Supply , installation & testing voltage stablizer, 5 KVA capacity, AC, single phase , 50 Hz, input volt 150 - 280 volts and out put voltage range 220 volts plus minus 7%, suitable for 2 Ton AC , with time delay relay,high & low cut off, suitable size and length of power cable & plug top etc complete with fixing arrangement etc Make :Bluebird/Microtek-EM4090/ V.Gaurd(VGMW500 Plus).complete all as Spd and as per direction of the Engineer-in-Charge

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 6 sq. mm + 1 X 6 sq. mm earth wire ( For AC).Make: Polycab/leygrand/Havells.complete all as Spd and as per direction of the Engineer-in-Charge

Supplying and drawing following sizes of FRLS PVC insulatedcopper conductor, single core cable in the existing surface/recessed steel/ PVC conduit as required. Size 3 x 1.5 sq. mm (For 5 amps shockets). Make: Polycab/leygrand/Havells.

All as per item No, 4 above but 2 X 2.5sq. mm + 1 X 2.5sq. mm earth (For Sub Main/circuits ).Make: Polycab/leygrand/Havells.complete all as Spd and as per direction of the Engineer-in-Charge

All as per item No, 4 above but 2 X 4sq. mm + 1 X 4 sq. mm earth (For power points ).Make: Polycab/leygrand/Havells.complete all as Spd and as per direction of the Engineer-in-Charge

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required:- Size 3X 16 sqmm + 1X 16 Sqmm as earth wire. (Main to Sub main TPN DBs),Make:leygrand/Havells/Schneider.complete all as Spd and as per direction of the Engineer-in-Charge

Supply and fixing MCCB enclosure Make: Legrand, (model Legrand 507801 DPX3 160 MCCB enclosure), suitable for housing 160 Amps 4 pole MCCB. Make: leygrand/Havells/Schneider.complete all as Spd and as per direction of the Engineer-in-Charge

Supply and fixing MCCB ,4 pole, 160 Amps, 25 KA, themal-magnatic release type ,Make : Legrand, in existing sheet steel enclosure as drected by Engr-in-charge.Make: leygrand/Havells/Schneider.complete all as Spd and as per direction of the Engineer-in-Charge

Supply and fixing sheet steel bus bar board includinding 4 Nos bus bars with drilled holes , nuts & bolts etc complete , 200 amps, 415 volts, AC ,50 Hz. Make: Kent/leygrand/Havells.complete all as Spd and as per direction of the Engineer-in-Charge

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBs & Isolator):- 6 way (4 + 18), Double door. Make: leygrand/Havells/Schneider.complete all as Spd and as per direction of the Engineer-in-Charge

All as per item No 11 above but 8 way (4+24),double door. (without MCBs & Isolator). Make: leygrand/Havells/Schneider.complete all as Spd and as per direction of the Engineer-in-Charge

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load connections, testing and commissioning etc. as required.following poles in the existing MCB DB complete with single pole. Make: leygrand/Havells/Schneider.complete all as Spd and as per direction of the Engineer-in-Charge

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 Amps. Make: leygrand/Havells/Schneider.complete all as Spd and as per direction of the Engineer-in-Charge

Supplying and drawing following pair 0.5 mm dia FRLS PVCinsulated annealed copper conductor, unarmored telephonecable in the existing surface/ recessed steel/ PVC conduit as reqd. Size 2 pair. Make: Polycab/leygrand/Havells.complete all as Spd and as per direction of the Engineer-in-Charge

Supplying and drawing co-axial TV cable RG-6 grade 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.Make: Polycab/leygrand/Havells.complete all as Spd and as per direction of the Engineer-in-Charge

Supplying and fixing of following sizes of medium class PVCconduit along with accessories in surface/recess includingcutting the wall and making good the same in case of recessed conduit as required. Make: AKG/Polycab/Havells.complete all as Spd and as per direction of the Engineer-in-Charge

Supplying and fixing suitable size PVC /GI box with modular plate and cover in front on surface or in recess or on PVC surface raceway system including providing and fixing of 6 pin 5/6 & 15/16 A modular multi socket outlet standard type and 15/16 A modular switch, connections as required at computer work station or in recess on wall, as required and directed at site by Engr-in charge.(Make: Legrand/Havells/Schneider and model : As per sample kept at CERS Building DEAL Complex).complete all as Spd and as per direction of the Engineer-in-Charge

Supplying and fixing suitable size PVC/ GI box with modular plate and cover in front on surface or in recess or on PVC surface raceway system including providing and fixing of fixing 3 pin 5/6 A modular socket outlet multistandard type and 5/6 A modular switch connections as required at computer work station or in recess on wall, as required at site and as per direction of Engr-in charge.(Make: Legrand and /Havells/Schneider and model : As per sample kept at CERS Building DEAL Complex).complete all as Spd and as per direction of the Engineer-in-Charge

Supply & fixing Telephone socket outlet.Make: Legrand//Havells/Schneider.complete all as Spd and as per direction of the Engineer-in-Charge

Supply & fixing TV antenna socket outlet.Make:Legrand/ Havells/Schneider.complete all as Spd and as per direction of the Engineer-in-Charge

Supplying and fixing32 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 32 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required(FOR AC Points).Make: Legrand//Havells/Schneider.complete all as Spd and as per direction of the Engineer-in-Charge

Supply and fixing PVC raceway on wall ,cubicles at computer work station suitable for fixing moduler switches , power sockets,computer sockets etc and drawing electrical, computer cables & tele cables etc, Size of PVC raceway 100mmx 100mm, inluding all acessaries required for fixing PVC raceway in white colour as approved and complete all as Spd and as per direction of the Engineer-in-Charge

supply and fixing Legrand power strip 8 module 5 pin 6 Amps (3 Nos) + 16 Amps switch with indicator(1 No) on the existing PVC raceway,including all accessories i.e. box,plate etc as required and directed at site. Make: Legrand//Havells/Schneider.

Supply & fixing RJ 45 socket on PVC racer for computer work station including gang box, face plate, jack etc complete as approved and directed by Engr-in-charge. Make: Legrand//Havells/Schneider.complete all as Spd and as per direction of the Engineer-in-Charge

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thickincluding accessories, and providing masonry enclosure withincluding accessories, and providing masonry enclosure withcover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc as required.

Supply only LT UG, XLPE cable 3.5 core ,35 sq mm with alumium conductor, armoured,1100 volts grade, heavy duty .Make: Make:Polycab/ Legrand/Havells.complete all as Spd and as per direction of the Engineer-in-Charge

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground /on wall ,including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Upto 35 sq. mm, complete all as Spd and as per direction of the Engineer-in-Charge

Providing and fixing G.I. pipes complete with G.I. fittings and clamps,i/c cutting and making good the walls etc.Internal work - Exposed on wall , 50 mm dia nominal bore.Make: TATA/JINDAL/SURYA.complete all as Spd and as per direction of the Engineer-in-Charge

Excavating trenches of required width for pipes, cables, etc including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering etc and disposing of surplus excavated soil as directed, within a lead of 50m: All kinds of soil pipes, cables etc not exceeding 80mm diametre.complete all as Spd and as per direction of the Engineer-in-Charge

ARP ASSOCIATES PRIVATE LIMITED

Sanjeev Construction Company

KUKREJA ENGINEERS

Santosh & Associates