Protection of Naharkatia Joypur road from the flooding of river Buridehing near Longjong Gaon.

Amount

Felling trees including uprooting roots and stumps up to 50 cm. below ground, cutting into pieces and removing the same from the site of work etc. complete as directed. Trees above 0.50 m and up to 1 m girth:

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401 For Grading II Material

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1. Govt. land

Providing stone piles of required diameter and length up to 10.00m in ordinary / dense soil etc. using 25 mm dowm graded stone aggregate or river gravel including cost of boring including watering, ramming etc. as required, Cost of T&P complete as directed and specified by the department. Pile Dia 300 mm

Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-25 of specified diameter and length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). 600 mm dia piles

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Single pile upto 50 tonne Safe capacity Initial test (Test Load 2.5 times the Safe capacity)

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Single pile upto 50 tonne Safe capacity Routine test (Test Load 1.5 times the Safe capacity)

Plain/Reinforced cement concrete, in sub structure complete as per drawing and technical specification and steel shuttering formwork Without plasticiser PCC Grade M15

Plain/Reinforced cement concrete, in sub structure complete as per drawing and technical specification and steel shuttering formwork Without plasticiser RCC Grade M20 Height upto 5m Using concrete Mixer

Supplying, fitting and placing TMT IS:1786 (Fe 500) bar reinforcement in sub-structure complete as per drawing and technical specifications TMT-IS 1786 ( Fe-500 D) Primary Producer (TATA/ SAIL/ Esser Steel/ Jindal panther steel/ Shyam steel or equivalent)

Tubular Steel Railing on Medium Weight Steel Channel (ISMC series) 100 mm x 50 mm Providing, fixing and erecting 50 mm dia steel pipe railing in 3 rows duly painted on medium weight steel channels (ISMC series) 100 mm x 50 mm, 1.2 m high above ground, 2 m centre-to-centre, complete as per approved drawings Clause 1706

Supply of Geo Bags Type-B (Size 2.00 m × 1.50 m inner to inner) (Pillow Type) made of composite layers of Polypropylene (PP) fibre as per IS 16653:2017 for Nonwoven and IS 16654:2017 for Woven: Woven Geo-textile for the outer cover (300gsm): The woven geo textile is woven with multifilament woven fabric manufactured from ultra violet stabilized polypropylene. Geo-textile used to manufacture geotextile bags should have high mechanical properties for enhanced durability along with enhanced puncture, abrasion and U.V. resistance characteristics. Geo-textile should be inert to biological degradation and resistant to naturally encountered chemicals, alkalis, and acids. Properties i. Tensile strength (MD) ≥ 80 KN/m & Tensile strength (CD) ≥ 70 KN/m ii. Elongation (MD) ≤ 25% & Elongation (CD) ≤ 25% iii. Abrasion ≥ 75% iv. Trapezoidal Tear Strength (MD) ≥ 1500N & Trapezoidal Tear Strength (CD) ≥ 1300N v. CBR Puncture strength ≥ 900N vi. Permeability ≥ 18 l/m2/sec vii. AOS ≤ 250 micron viii. UV Resistance @ 500 hours retained Tensile strength (MD) & (CD) ≥ 80% ix. Mass ≥ 300 gm/m² x. Seam strength ≥ 50 % of actual fabric strength. Non-Woven Geo-textile for the inner layer (300gsm): It is needle punched non-woven geo-textile made of 100% polypropylene staple fibres which are formed into a random network for dimensional stability. It should resist UV degradation, rotting and alkalis. Properties i. Wide Tensile strength (MD) ≥ 15 KN/m & Wide Tensile strength (CD) ≥ 15 KN/m ii. Elongation (MD) ≥ 50% & Elongation (CD) ≥ 50% iii. Abrasion ≥ 95% iv. Trapezoidal Tear Strength (MD) ≥ 340 N & Trapezoidal Tear Strength (CD) ≥ 340 N v. CBR Puncture strength ≥ 3000 N vi. Permittivity ≥ 1.25 s-1 vii. Permeability ≥ 60 l/m2/sec viii. AOS ≤ 75 micron ix. UV Resistance @ 500 hours retained Tensile strength (MD) & (CD) ≥ 80% x. Mass ≥ 300 gm/m² xi. Thickness at 2KPa ≥ 3 mm xii. Seam strength ≥ 80 % of actual fabric strength. Stitching of Bags should be Ring Spun Yarn stitches with 2500-3000 denier double line chain stitch with overlap with stitches along the edge. (Bags are to be supplied of 15 numbers in a bundle, properly packed with each bag having proper tag with name of Manufacturer, Batch Number, the GSM and type of polymer encrypted and stitched on top corner and each bag is to be marked with “WRD Govt. of ASSAM” to be printed distinctly. Test Certificate from approved NABL accredited and ISO Certified Laboratory should invariably be submitted against each batch of material)

Carriage of Geo Bags of size 2.00 × 1.50 m including loading & unloading, stacking cost of P.O.L. etc. complete and including hire charge of truck with driver and handyman, etc. completed as directed. (Distance to be calculated from divisional store = 55 km)

Filling and laying of nonwoven Geo - textile bag of dimension 2.00 m × 1.50 m excluding excavation of specified sand/silt from flood plain or adjacent chars within a distance of 90 m of the work site, filling geo bags with sand having minimum volume 0.612 Cum after filling, double locking chain stitching the mouth of the filled bags with polypropylene thread by power driven double needle machine, laying at proper site including all handling charges and local carriage within a distance of 100 m complete as directed. (Sand/silt, Geo Bag and Polypropylene thread will be supplied by the department free of cost) Without Bag

Supply of Sewing Thread/Yarn PPMF Stitching Thread (2000 Den. Kaplon).

Collection and supply of sand from approved quarry of specified grade for construction work free from debries and other foreign material etc. complete as directed.

NUMAL SAIKIA