Proposed Construction of Two Nos New 70 Mens Barrack of New High Court Jharkhand at Dhurwa, Ranchi.

Amount

Earth Work Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of cavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.

Hard rock (blasting prohibited)

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials.

All kinds of soil

Supplying chemical emulsion in sealed containers including delivery as specified.

Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for PRE-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:

With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, leveling & dressing & finishing the top smooth.

Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5M all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Extra for lead up to 1KM Beyond the initial lead of 50M as per specifition and direction of Engineering -in charges.

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of Eli ( Mode of measurement compacted volume)

Concrete Work Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All works upto plinth level :

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

RCC Work Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size) derived from natural sources.

Centering and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Stairs, (Excluding landings) except spiral -staircases.

Weather shade, Chajjas, corbels etc., including edges

Cornices and mouldings

Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick

Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5 m for every additional height of 1 metre or part thereof (Plan area to be measured.) Suspended floors, roofs, landing, beams and balconies (Plan area to be measured).

Providing Tor steel reinforcement of 8mm& 10 mm. dia . rods as per approved design and drawing including cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position (excluding carriage of M.S. bars to work site) all complete as per building specification and direction of E/l. TMT Fe 500 (only vailid for Tata (tiscon), SAIL, JSPL, Electrosteel ltd Bokaro and Vizag(RINL))

Providing Tor steel reinforcement of 12mm.& Above dia . rods as per approved design and drawing including cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position (excluding carriage of M.S. bars to work site) all complete as per building specification and direction of E/l. TMT Fe 500 (only vailid for Tata (tiscon), SAIL, JSPL, Electrosteel ltd Bokaro and Vizag(RINL))

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Providing and laying in position ready mixed or site batched design mix cement concreete for reinforced cement concerete wirk; using coarse aggrement and fine aggrement derived from natural sources, Portland Pozzolana / Oridinary Portland / Portland slag cement admixtures in recommended propottios as per IS 9103 to accelerate / retard setting of concrete , to improve durability and workablity without impairing strength ; including pumping of concrete to site of laying, curing. carriage for all leads; but excluding the cost of centering , shutring finidhing and reinforcement as per direction of the eingineer- in- charge ; for the following grades of concrete. Note : Extera cement up to 10% of the minimum specified cement content in disign mix shall be payable separately in case the cement content in design mix is more than 1.10 of the specified minimum cement conteent, the contractor shall have discretion to either re-design the mix or bear the cost of extera cement

All works upto plinth level Concrete of M25 grade with minimum cement content of 330kg/cum

All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330kg/cum

Brick Work Providing designation 75A brick work in C.M (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Extra for providing and placing in position 2 Nos. 6 mm dia. M.S. bars at every third course of half brick masonry.

Providing designation 112mm thick reinforcement designtion 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:4) in supertructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including cost of screening materials scaffoliding raking out joints to 15mm depth curing taxesand royalty ( but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.

Construction of Dry Lean Cement Concrete over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25mm aggregate cement ratio not to be exceed 15:1 aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/cum, optimum moisture content to be determined during trial length construction concrete strength not to be less than 10Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor compacting with 8-10 tonnes vibratory roller finishing and curing.

Construction of un-reinforced, dowel jointed Pavement Quality concrete over a prepared Sub-base with approved grade cement @ 400kg per cum,coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25mm mixed in a batching and mixing plant as per mix design, transported to site laid with a fixed form or slip form paver, spread, compacted and finished ina a contiinous operation including provison of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar tie rod, admixture as approved curing compound finshing to lines and grades as per drawing

Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

Providing and laying autoclaved aerated cement blocks masonry with AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for separately).

Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183, having density 48 kg/m3,50 mm thick,wrapped in 200 G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held and in position by criss cossing GI wire etc. complete as per directions of Engineer-in Charge.

Marble Work Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade

Area of slab over 0.5 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Granite work

Extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/ Granite/ stone work including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand), laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing 18 mm thick pre-polished granite stone in dado, skirting, risers of steps etc., on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with cement slurry @ 3.3 kg/sqm and pointing with white cement slurry ad-mixed with pigment of matching shade etc. all complete as per Architectural drawings and as per direction of the Engineer-in-Charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Sal wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete :

2nd class teak wood

Extra for pre finished nosing to treads of steps of marble/ granite stone.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

1:4 (1 cement : 4 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix:

1 : 6 (1 cement : 6 fine sand )

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to openings with rawl plugs screws etc.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

Extra for Marble/ granite stone in treads of steps and risers using single length up to 2.0 metre .

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

25 mm thick.

Kota stone slabs 20mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1: 3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 600x600 mm

Providing and laying Double charge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm .

Roofing Making khurras 45x45 cm. with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) over PVC sheet1mx1mx400 micron, finished with12 mm cement plaster1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :

In 75x75 mm deep chase metre

Finishing Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete

Painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.

Two coats.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:

New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing two coats of synthetic enamel paint of approved shade and make over Red lead Primer steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Extra for plastering done on moulding, cornices or architraves including neat finish to line and level:

In two coats

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.

UPto 5mm depth and 5mm width

Providing, assembling, supplying & fixing of vision glass panels (IGUs), in UPVC/ Aluminium windows, comprising of hermetically-sealed 6- 12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. For payment, only the actual area of glass on face # 1 of the glass panels shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Casement window single panel with S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 0.75 sqm.)

Casement window double panels with S.S. friction hinges (350 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash / mullion 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 1.50 sqm).

Providing and fixing casement handle made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc. complete.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: Applying a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. Laying brick bats with mortar using broken bricks /brick bats 25 mm to 115 size with 50 % of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer -in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement : 5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.

After two days of proper curing applying a second coat of cement slurry using 2.7 kg/sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer -in-charge. Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement : 4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer -in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern fo 300 x 300 mm square 3 mm deep. The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer -in- charge.

With average thickness of 120mm and minimum thickness at khurra as 65 mm.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C kitchen and the like consisting of : Ist course of applying cement slurry @ 4.4 Kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. IInd course of 20 mm cement plaster 1: 3 (1 cement :3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm.)

Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Carriage of material

Sand 10 Km.

Bricks 8km(1KM+7P)

Stone chips 22 Km.

Stone METAL 22 Km.

Plumbing SANITARY INSTALLATIONS Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 litre/8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink with drain board 510x1040 mm bowl depth 225 mm

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore

Providing and fixing C.P. brass toilet paper holder :

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I.

Mirrors of 6mm thick plate glass bevelled edge mirror including C.P.brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror. 600mm x 450mm size.

C.P. brass liquid soap container.

Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms

Providing and fixing 15mm size C.P. brass pillar cock (Weight not less than 350gms).C.I. body brass spindle pillar cock of approved quality as per specification and direction of Engineer-in Charge. C.P. body brass spindle.

WATER SUPPLY Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

40 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

40 mm nominal outer dia Pipes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

SOIL, WASTE, VENT & RAIN WATER PIPES Providing and fixing on wall face unplasticised Rigid PVC rain water and waste pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm outer dia

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

1.2 Meter high and 250 mm dia.

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)

Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520

Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325.5

M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.

Suitable cement concrete foundation duly plastered and with anti vibration pads.

450 lpm at 35 m Head

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

100 mm dia

25 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

100 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

100 mm dia

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.

100 mm dia

SUB HEAD - III - (HYDRANTS SYSTEM) Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

Single headed Stainless steel

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Stainless Steel (Grade 304)

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

Stainless Steel (Grade 304)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required.

20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585

20 mm nominal internal dia gun metal globe valve & nozzle.

Drum and brackets for fixing the equipmets on wall.

Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :

2 way-100 mm dia M.S. Pipe

ELECTRICAL WORKS SUB HEAD (I) :- INTERNAL WIRING Point wiring in PVC conduit, with modular type switch :- Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 Sq.Mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular type switch, modular plate,suitable GI box etc. as required.

Group A

Power plug wiring in PVC conduit (2 x 4 Sq.Mm.) :- Wiring for power plug with 2 x 4 Sq.Mm. FR PVC insulated, copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 no 4 Sq.Mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Circuit / Sub main wiring in PVC conduit :- Wiring for circuit / submain wiring alongwith earth wire with the following sizes of PVC insulated, copper conductor single core cable in surface/ recessed PVC conduit as required.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire.

4 x 6 sq.mm. + 2 x 6 sq.mm. Earth wire.

4 x 10 sq.mm. + 2 x 6 sq.mm. Earth wire.

4 x 16 sq.mm. + 2 x 6 sq.mm. Earth wire.

S/F light plug point Modular type accessories :- Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps. modular Type Switch, connection, painting etc. as required.

S/F power plug point modular type accessories :- Supplying and fixing of suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps. modular switch, connection, painting etc. as required.

Supplying and fixing of following modular switch/ socket outlet on the existing Modular plate & switch including connection but excluding modular plate etc. as required.

5/6 amps switch

3 pin 5/6 amp socket outlet

Supplying and fixing following size/ modules, GI box Boxes alongwith modular base & cover plate for modular switches in recess etc as required.

1 or 2 Module (78mmX78mmX45mm)

6 Module (78mmX205mmX50mm)

Telephone Socket outlet

TV Antenna socket outlet

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A, “C” curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

S/F Modular type electronic fan regulator :- Supply and fixing of stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

S/F Modular type Blanking Plate :- Supply and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Providing and fixing hexagonal fan box circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

SUB HEAD (II) :- TELEPHONE, TELEVISION & DATA SYSTEM S/F PVC Conduit Supplying and fixing of following sizes PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required :

Supply and drawing co-axial TV cable RG-6 grade copper conductor PE insulated,with PVC sheath in the existing surface / recessed PVC conduit as required.

SUB HEAD (III) :- DISTRIBUTION BOARDS & MCB's S/F T.P MCB DB :- Supplying and fixing following way, three pole and neutral, sheet MCB distribution board 415 volts,on surface /recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, Phosphatized and powder painted including earthing etc. as required (But without MCB / RCCB / Isolators).

8 way (4 + 24), Double door, Horizontal Type

Providing and fixing following capacity busbar chamber with 4 strip of length 300mm made of copper suitable for following capacitty complete with all accessories including connections, earthing the body etc as required

S/F 4P MCB Isolator Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required

80/100 Amps(Incomer for Vertical DB)

125 Amps (Incomer for Vertical DB)

S/F SPN (RCCB) Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

S/F 'C' Series MCB :- Supplying and fixing following 240 volts `C' series, miniature circuit breaker (MCB)suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

6/32 amps, Single Pole

50/63 Amps TPN (Outgoing for Vertical DB)

Supplying & fixing single pole, blanking plate in the existing MCB DB complete etc. as required.

MAIN BDS S/F VERTICAL TYPE T.P MCB DB :- Supplying and fixing following way, three pole and neutral, sheet MCB distribution board 415 volts,on surface /recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, Phosphatized and powder painted including earthing etc. as required (But without MCB / RCCB / Isolators).

8 way (4 + 24), Double door,Vertical Type

Providing and fixing M.V. danger notice plate of 200mmx150mm made of mild steel, atleast 2mm thick and vitreous enamelled white on both sides and with inscription single red colour on front side as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having arrangement and watering pipe etc. (but Without charcoal and Salt) as required

SUB HEAD IV):-INTERNAL LIGHTING FIXTURES & FANS SUPPLY OF LIGHTING FIXTURES Supply of Surface Mounting Round 12 Watt LED Down Lighter having Powder Coated die cast aluminium housing with heat sink,diffuser/reflector and driver set complete in all respect.

Supply of LED MIRROR LIGHT Complete Including tube etc on Wall complete in all respect .

Supply of LED BULK HEAD LIGHT Complete Including tube etc on Wall complete in all respect .

Supply of AC 230/250 volts, 50 HZ ceiling fan with standard down rod, blades, 2 nos. caps & regulator etc. ISI marked complete as required..

1200 mm sweep (fusion-50 5*)

Supply of AC 230/250 volts, 50 HZ exhaust fans including providing nuts, bolts, mounting frame and other accessories etc. complete (Approved Make).

Exhaust Fan Heavy duty 230V A.C 50 cycles 375 mm 1400 RPM

Installation, testing and commissioning of ceiling fan including wiring the down rod of standard length (upto 30 cm.) with 1.5 sq. mm. FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

ITC Exhaust fan upto 450mm sweep:- Installaition of Exhaust Fan upto 450 mm, sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc as required

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.

LT CABLE LAYING Laying of one number additional PVC insulated and PVC sheathed/ XLPE power cable 1.1 KV grade of following size in the existing rcc/hume/stoneware/metal pipe as required .

up to 35 sqmm

Supply and making end termination with brass double compression gland including providing and crimping of Aluminium solderless lugs / ferrules for XLPE armoured power Aluminium conductor cable 1.1 KV grade of following sizes:-

3.5 x 35 sq.mm

3.5 x 25 sq.mm

4 x 16 sq.mm

External plumbing Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :All kind of soil

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size), inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 80x90 cm and 60cm deep including SFRC cover with frame (Medium duty) 800x900 mm internal dimensions.

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular type manhole 0.91m internal dia at bottom and 0.56m dia at top in cement motar 1:4 (1 cement :4 coarse sand), in side cement plaster 12 mm thick with cement motar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement :3 coarse sand sand :6 graded stone aggregate 40mm nominal size), and making necessary channel in cement concrete 1:2:4 ( 1cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design:

0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for circular type manhole 0.91m internal dia (at bottom with beyond 0.91m to 1.67m

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular type manhole 1.22m internal dia at bottom and 0.56m dia at top in cement motar 1:4 (1 cement :4 coarse sand), in side cement plaster 12 mm thick with cement motar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement :3 coarse sand sand :6 graded stone aggregate 40mm nominal size), and making necessary channel in cement concrete 1:2:4 ( 1cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design:

1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for circular type manhole 1.22m internal dia (at bottom with beyond 1.68m to 2.29m

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular manhole 1.52 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :

2.30 m deep with SFRC Cover and frame (heavy duty HD- 20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

150 mm diameter

250 mm diameter

300 mm diameter

Supply of LED Tube Light with Batten Suitable for 1x24 Watt LED Tube Light Complete Including tube etc on surface complete in all respect Polycab Cat No Intenso LED Batten SQ PC 4ft 24W 6500K 2 or equivalent

Floodlight LED luminaire 150 Watas with high pressure die cast housing with IP66 deg of protection of Polycab Cat No. PCGLF T1 01 150 or equivalent

Installation testing commissioning of TPN DBs of 4 way to 12 way including incoming outgoing MCBs,RCCBs,incoming submains wire and outgoing connection & termination of circuits / wires complete in all respects

SUB-HEAD -III : HT & LT. CABLES Supply of undernoted sizes of aluminium conductor XLPE insulated PVC sheathed & sleeved armoured and overall PVC sleeved 1.1 KV grade power distribution cables conforming to relevant IS code and as per specification in ground (in existing trenches) through pipe or on wall / racks cable trays including dressing and clamping the cable with MS zinc passivated clamps etc. as required.

3.5 x 16 sq.mm

3.5 x 25 sq.mm

3.5 x 35 sq.mm

Installation testing and commissioning of 7 Mtr height Octagonal Pole & Light fittings with the help of suitable tool and plant,wiring of luminere with all material and connection of shellow foundation with M25 grad concrete considering safe soil bearing capacity of 10T / Mtrs sq

Supply, installation, testing and commissioning of following street light luminaire complete in all repect.

90/100W LED Street Light

Providing and displaying of Raphis palm plant, having ht. 75 cm to 90 cm with 15 to 18 equal suckers, well developed, full of fresh and healthy leaves from bottom to top in 25 cm size of Earthen pot / Plastic pot & as per direction of officer-in-charge. Specification 75 cm to 90 cm ht. 12 to 15 suckers

Providing and displaying of cephortia Palm Plant, having ht. 90 cm to 1.20 m with 6-8 suckers, well developed, full of fresh and healthy lush green leaves from bottom to top in 20 cm size of Earthen pot / Plastic pot & as per direction of officer-in-charge. Specification 90 cm to 120 cm ht. 6 to 8 suckers

Supply and stacking of plant Caesalpinia pulcherrima species of height 45-60cm. In earthen pots of size 20cm as per direction of the officer-in-charge Specification 45-60cm. Ht.

Supply and stacking of plant Calliandra hybrida of height 105-120cm. Well branched, bushy in big size HDPE bag as per direction of the officer-in-charge Specification 105-120cm ht. with r-5branches

Supply and stacking of plant Cassia biflora of height 60-75cm. With 4-5 branches in poly bags of size 25cm as per direction of the officer-in-charge Specification 60-75cm ht. with 4-5 branches

Providing and displaying of Croton Golden speciment plant, having ht. 90 cm to 1.05 cm with 5 to 6 branches, well developed , fresh and healthy foliage in 30 cm size of Earthen pot / Plastic pot & as per direction of officer-in-charge. Specification 90 cm to 105 cm ht. 4 to 5 branch

Providing and displaying of Croton Duck Foot (Elite) plant, having ht. 60 cm to 75 cm with 4 to 5 branches, well developed , fresh and healthy colourful leaves in 25 cm size of Earthen pot / Plastic pot & as per direction of officer-in-charge. Specification 60 cm to 75 cm ht. 4 to 5 branch

Providing and displaying of Speciman Croton petra Bangalore variety plant, having ht. 60 cm to 75 cm with 4 to 6 branches, well developed , fresh and healthy foliage approximately 60-65 leaves 30 cm size of Earthen pot / Plastic pot & as per direction of officer-in-charge. Specification 60 cm to 75 cm ht. 4 to 6 branch

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.

With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).

Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in :

Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm

Steel weld mesh

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulation etc. and re-rolling the subgrade and disposal of surpulus earth with lead upto 50 metres.

Supplying and stacking at site. Moorum

Supplying, stacking and Spreading moorum, watering and rolling complete including preparation of the surface and rolling. With road roller/hand roller

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). (length of finished kerb edging shall be measured for payment).(Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Non-Sheduled Item Supply & fixing of door closers of UL listed Heavy duty std arm with silver body finish and tested in accordance of EN 1634 - 3 and for mechanical test to EN 1154 for 50000 cycles and shall be tested with the fire doors for 2 hrs. fire rating from the CBRI Roorkee as per the directions of Engineer-in-charge

Wood Work Providing and fixing aluminium die cast body TS 68 door closer with standard arm (EN2/3/4 max door width 1100mm necessary accessories and screws etc complete of approved make

Providing and fixing approved brand and manufacture SS 304 grade Tower bolt (TBS 310 S)250mm long with 10mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 Lever Handle D-type 25mm x 300 (PH2512) mm fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing Approved', make Glass Reinforced Concrete (G.R.C) Screens casted with 'Spray Mix' concrete design in approved size, pattern, thickness of 50mm on the outer Border & 25-30mm for Internal member and shade. The Screens should be made from ‘53 grade’ White Portland Cement , White Quartz fine graded sieved Silica Sand, Alkali Resistant Glass Fibre , Owen Corning, Super Plasticizers, Polymers and U.V resistant Synthetic inorganic pigments should be used for pigmentation The Screens casting shall take place with layering methodology using- Direct Power Spray machines. The GRC Screens flexural strength average L.O.P should be above or equivalent to 6 N/mm2 & M.O.R should be above or equivalent to 15 N/mm2 for tests done on 28 days cured samples.

The fixing of Screens should be done using ‘Dry fixing’ method onto structural support members i.e. R.C.C, Brick work, MS Framework. SS / MS Galvanized CLAMPS & PINS also if required fasteners to be used of Wurth, Hilti & Fischer or equivalent. All Cast in Socket to be Epoxy Primer Coated. Electrodes, Vendor shall submit shop drawings of same, the drawings to be duly approved from Engineer in charge at site

Providing & Fixing Kent Perk Auto,RO,UV& TDS Controller Storage Water Cooler Cum Purifier Water Storage Capacity: 20 ltrs. , Three mode of Operation (Auto, RO,UV & TDS Controller as Per Raw Water Quality), Purification capacity 50 Litre/hour, Two Faucets, alongwith 1 year annual maintainance contract (AMC) (Detail Technical Description as Per the given details ) With Accessories.

Plumbing SANITARY INSTALLATIONS Providing and fixing of CP brass Health faucet with 8mm dia 1mtr. Long PVC tube and wall hook fixed to wall with rawl plug and CP brass screws complete. (Approved Make)

Providing and fixing HDPE pipes of PE 80 Grade stabilized including all HDPE as per IS:4984 electrofusion fittings i/c support at 1.0mm c/c & testing of joints complete as per direction of Engineer in Charge

PN - 8 Pipe, 63 mm OD PE80

Supplying & Placing cafe chair. The complete structure shall be made up of 20% glass filled injection moulded polypropylene. The frame structure shall be supported by four legs made up of polypropylene having Dia. 35mm at upper and 25mm at lower i.e taper shape. The seat size shall be 410±10 mm(D) X 400±10 mm(W) and back size shall be 390±10 mm(W) X 420±10 mm(H) from seat. Overall height shall be = 845±10 mm, overall depth = 510±10 mm. Geeken Model No.GC 987 Size Stackable

Providing and supplying 4 seater visitor chair with 5 arms. The seat and back shall be made up of reinforced PU foam with MS perforated sheet. The seat mounted on MS powder coated rectangular cross beam having cross-section area 60mm X 60mm with 2mm thick fitted with polypropylene end caps on both side. The arm and leg shall be made up of pressure diecast aluminium. There shall be leveller shoe provided at the bottom with metal insert. The individual seat size shall be 515±10 mm(W) X 467±10 mm(D), Back size shall be 515±10 mm(W) X 510mm±10 mm(H) from seat, Overall depth shall be 680±10 mm, overall wifth shall be 2180±10 mm and overall height shall be 860±10 mm. Geeken Model No.Fly 4 Size

Supplying & Placing cafeteria table with an overall size 1200mm X 900mm X 750mm. The top shall be made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on MS/CRCA rectangle pipe frame having cross-section area 70mm X 20mm with 1.6mm thick. The understructure shall consist of four legs made up of MS round pipe having dia. 38.1mm with 1.6mm thick. The Joints shall be made using TIG welding. The metal parts shall be powder coated to dry film thickness of 40-60µ. There shall be PPCP shoe provided at bottom to avoid scratches on the floor. Geeken Model No.Customised Size 1200x900

Supplying & Placing cafeteria table with an overall size 2100mm X 900mm X 750mm. The top shall be made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on MS/CRCA rectangle pipe frame having cross-section area 70mm X 20mm with 1.6mm thick. The understructure shall consist of four legs made up of MS round pipe having dia. 38.1mm with 1.6mm thick. The Joints shall be made using TIG welding. The metal parts shall be powder coated to dry film thickness of 40-60µ. There shall be PPCP shoe provided at bottom to avoid scratches on the floor. Geeken Model No.GC 9032 Size 2100x900 (Ciustomised Size)

Providing, supplying and placing steel Almirah. The overall size of the Almirah shall be 900mm (W) X 450mm (D) X 1830mm (H). The cabinet shall be supplied with 2 nos. of doors and 4 nos. of adjustable shelves. The doors shall be operated with aesthetically appealing snap fit ABS plastic handle and concealed crank hinge. The shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. Uniformly distributed load capacity of each shelf shall be 40 Kg maximum. Each rack shall be provided with stiffener at bottom for strength. The entire body panel, shelf shall be made of high yield strength 0.8mm thick CRCA sheet of grade ‘D’ confirming to IS: 513. To protect the ball from kicks, abrasion and serve as a decorative moulding skirting shall be provided at the bottom of the Almirah. The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40-50µ thick. Geeken Model No.GMS 10 Size

Providing, placing and installing a slotted angle rack with an overall size 900mm (W) X 450mm (D) X 1800mm (H). The panel shall have 5 nos. of shelves made up of 0.8mm thick high yield strength CRCA sheet of grade ‘D’ confirming to IS: 513. CRCA slotted angle shall be supplied with 2mm thick having size 40mm X 40mm. All steel components shall be 50-60µ thick (DFT) powder coated after 7 tank pre-treatment process flow. Corner plate (gussets) and fasteners shall be provided for complete assembly. Geeken Model No.GMS 20 Size 900x450x1800

Providing and placing in position single bed with an overall size - 1925mm (L) X 965mm (W) X 1000/450mm (H) without mattress. The construction of the bed shall be supplied in knock down with metal frame made out of MS/CRCA steel pipe having cross-section area 50mm X 25mm with 1.2mm thick. Head and tail panel shall be constructed from CRCA round pipe having dia. 19mm X 1.2mm thick and 15.8mm with 1.2mm thick. The mattress panel shall be made of 19.05mm X 19.05mm square pipe with 1mm thick. The legs shall be made of M.S.E.R.W pipe having cross-section area 40mm X 40mm with 1.2 mm thick. All metal part shall be powder coating finish with DFT(Dry Film Thickness) - 35µ min. The PPCP shoes shall be insert into bottom of legs for avoid skretches on the floors. Geeken Model No.Hostel 2 Size 1925x965x1000

MATTRESSES 4'' Mattresses Geeken Model No. Size

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.

100 mm dia

80 mm dia

Supply, Installation, Testing and Commissioning of 100 mm dia Bourden type, Stainless Steel dial type Pressure Gauge including brass isolation valve and siphon pipe having calibration of 0 - 15 Kg / cm2 .

Supplying and Fixing of Fire Man's axe with heavy insulated rubber as per standard conforming to IS 926.

Providing & fixing 25mm dia. UL listed gunmetal inspector test and drain valve with integral sight glass connected to drain line complete in all respects.

Providing and fixing weather proof lockable cabinet of size not less than 0.9 x 0.6 x 0.25 mtr made out of MS sheet 2mm thick having central opening and 6 mm thick glazed glass doors (Two nos.) suitably marked on the outside with the letters "FIRE HOSE" including necessary locking arrangement and shall be painted with one coat of primer and two coats of synthetic enamel paint (Post Office Red) of approved shade as required as per specifications.

SUB HEAD - III - (HYDRANTS SYSTEM) SITC weather proof M.S Door and glass fire door size 2100 mm x 900 mm or as per arch. Supplying, installation, testing and commissioning of weather proof M.S door and glass fire door size 2100 mm x 900mm fabricated from 1.6mm thick M.S. sheets and M.S angle 40mmx40mmx6mm complete with glass, locking arrangements to accommodate the following: -

a) Gunmetal single headed Hydrant valve - 1 No. b) Fire Hoses 63mm, 15 M long with accessories - 2 Nos. c) Short branch - 1 No. d) First Aid hose Reel - 1 No. e) Fire Extinguisher - 2 Nos. f) Fireman's Axe - 1 No. g) Pressure Gauge - 1 No. The cabinet shall be painted with one coat of primer and 2 coats of synthetic enamel paint of approved shade.

SUB HEAD - IV - (FIRE EXTINGUISHERS) Providing and fixing fire extinguisher of carbon dioxide type consisting of brand new high pressure steel cylinder bearing IS: 7285 mark and having the approval of controller of explosives Nagpur, wheel type valve bearing IS:3224 mark internal discharge tube, 1 meter long high pressure discharge hose, non conducting horn, suspension bracket, fully charged bearing IS: making fixed to wall as directed.

6kg capacity cylinder.(ABC TYPE)

Providing and fixing fire extinguisher of ISI marked (IS:15638) portable chemical fire extinguisher, water (gas pressure) type capacity 9 litres with gun metal cap and nozzle and complete in all respects including initial fill and wall suspension brackets as required as per specifications.

Telephone cable in existing conduit RJ 45 socket for Lan cat 6 Polycab Cat No SLV0400401/02

Supplying, laying, testing and commissioning of following size anealed tinned copper conductor PVC insulated and sheathed copper conductor, unarmoured telephone cable in the existing surface / recessed steel/ PVC conduit with suitable clamps, saddles and including making terminal joints complete as required.

Supply of WALL BRACKET LIGHT Complete Including tube etc on Wall complete in all respect of Polycab Cat No LED Wall Mount Fixture - GL 12404 or equivalent

Bullet Camera 2 MP - Supply, Installation, Testing & Commissioning of IP Network TDN Low-Light IR Bullet Camera, 1/2.8" CMOS, 2 MP @ 60fps , triple stream, Min. Illumination required 0.001 lux @ F1.6 (color), 120dB True WDR, Min. Pixels 1920 × 1080, triple stream, 2.7–13.5 mm motorized focus & zoom lens, S/N ratio - 50 dB min, BLC, HLC, 3DNR, Privacy Mask, 4 IR LEDs Smart IR with upto 60m IR distance, Dual channel Audio G.711a/G.711u/AAC, 128GB SD card support, Alarm: 2 In/ 1out, PoE, H.265+, H.265,H.264 High Profile and MJPEG, PoE Class 3 and 12V DC, IP 67, IK 10 vandal proof, Having Operating temp range : –40°C to 60° C. Certifications: ONVIF Profile S, Profile G & profile Q compliant, UL, UL CAP, GDPR, CYber Security certified,CSA 60950-22, CE (EN 50130-4 & EN 55022) , FCC Part 15 & RoHS compliant. Original Equipment Manufacturer (OEM) Authorisation letter along with Channel Partner certificate need to submit before implementation and same has be confirmed & Certified by engineer in charge Approved make.

Bullet Camera 4 MP - Supply, Installation, Testing & Commissioning of IP Network TDN Low-Light IR Bullet Camera, 1/3" CMOS, 2 MP @ 60fps , triple stream, Min. Illumination required 0.01 lux @ F1.6 (color), 120dB True WDR, Min. Pixels 2560x1440, triple stream, 2.7–12 mm motorized focus & zoom lens, S/N ratio - 50 dB min, BLC, HLC, 3DNR, Privacy Mask, 4 IR LEDs Smart IR with upto 60m IR distance, Dual channel Audio G.711a/G.711u/AAC, 128GB SD card support, Alarm: 2 In/ 1out, PoE, H.265+, H.265,H.264 High Profile and MJPEG, PoE Class 3 and 12V DC, IP 67, IK 10 vandal proof, Having Operating temp range : –40°C to 60° C. Certifications: ONVIF Profile S, Profile G & profile Q compliant, UL, UL CAP, Cyber Security certified,CSA 60950-22, CE (EN 50130-4 & EN 55022) , FCC Part 15 & RoHS compliant. Original Equipment Manufacturer (OEM) Authorisation letter along with Channel Partner certificate need to submit before implementation and same has be confirmed & Certified by engineer in charge Approved make

PoE Switch 8-Port, Rack mountable Layer II Managed Gigabit Ethernet standalone chassis provides 8 PoE RJ-45 10/100/1000 BaseT, 2 SFP/RJ-45 10/100/1000 BaseT or 100/1000 BaseX combo and 2 SFP Gigabit uplinks ports with internal AC power supply (120W PoE), 10 Gigabit SFP+ stacking module with 1m long SFP+ direct stacking cable etc complete as required - Approved Makes

6 Core SM 9/125 ITU G.657A1 Bend Insensitive, Indoor- Outdoor, CST Armour, Rodent Protected, Double LSZH Jacket IEC 60332-3-22 Fiber Optic Cable

SUB HEAD(XI):- LAN SYSTEM Providing and Fixing of CAT 6 Giga speed cable exceeding, Cat6 standard complete as required approved make

Providing and Fixing of 24-port loaded, Modular Jack Panel, 1U (For Data and voice UTP Field Cables)approved make

Providing and Fixing of Slime line RJ45 to RJ45 Cat6 UTP Patch cord ( Data Rack end) = 3 Feet approved make

Providing and Fixing of 19-inch rack mount patch panel, 1U, 24 port loaded with Adapter Plates SC Style approved make

Providing and Fixing of 19-inch rack mount patch panel, 1U, 6 port loaded with Adapter Plates SC Style approved make

Providing and Fixing of OFC patch cord -3 Mtr. Long. Approved Approved Make

Providing and Fixing of Switch with 24 x 10/100/1000 Base T Ports , 4x1000 Base X Ports ( Combo Shared ) and 2 dedicated stacking ports with min Stacking Bandwidth of 40Gbps or more as technical specifications enclosed etc. as required approved make

Providing and Fixing of 1G Module For Fiber Connectivity approved make It should be of same make as that of Switch OEM

Providing and fixing of signages, curved frame technology,of various widths and lengths, to form suggested usages,made of aluminium extruded sections , duly anodised ,all signages shall be provided with 0.6-0.8mm polycarbonate protecting film over the prints, of appropriate size, Model :Galaxy by Claudeneons or Equivalent. Way finding Signs Way finding ceiling hung sign(both side) 1000x210

Providing and fixing of disclaimers/special information/area names/ restricted area/prohibition, with 3M make digitally printed vinyl duly pasted on exsisting wall/ glass surface Digitally printed vinyl

Proving and Fixing of COUNTER BASIN Syze 550 mm X 400 mm

Add 18 % GST

Add 1% Labour Cess

Awadhesh Singh Construction Pvt Ltd