Supply, installation, testing and commissioning of electro-mechanical equipments and construction of pump house/panel room/ operator room at water supply scheme Aripal Lift.

Amount

(Part A: Electro-Mech.) WSS Aripal Lift (Adv. Cost Rs. 50,83,000/-)

Supply, Installation, Testing & Commissioning of Submersible Pumping Unit as per IS 8034 with following specification are as under : Complete specification as per cluase 1 of of SBD capacity of motor = 15 HP or suitable for above parameters

Providing/supplying and fitting of G.I flanged Rising Main at site. The Pipe shall be hot dip Galvanized, class B and C confirming to IS 1239. The job includes providing and fitting of M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16). Detailed specification as per cluase "8" of of SBD Size : DN80 Class: C (Heavy)

Earth work in excavation by manual means in trenches for foundation, drains, pipes, cables (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and reaming of bottom lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed. (All kinds of soil 01 meter from cutting edge)

Filling available excavated earth in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by reaming and watering, lead upto 50 m and lift upto 1.5m.

Providing and laying of stone soling including manual compaction

Centering and shuttering including strutting , propping etc. and removal of form work for Foundation, footings, bases for columns

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering . all work upto plinth level with 1: 2 : 4 mix ( 1 cement , 2 coarse sand , 4 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering . all work upto plinth level with 1: 3 : 6 mix ( 1 cement , 3 coarse sand , 6 graded stone aggregate 40 mm nominal size)

12 mm thick cement plaster of mix 1:4 ( 1 cement : 4 fine sand)

Fabrication, providing and fitting of split type MS clamps10 mm thick, 2 ft long and 3 inch wide for lowering and holding of pumping unit fitted. The job includes the cost of required size of nuts and bolts. Size: 80mm

Providing and fitting of bend with flanges .The Flanges shall be MS conforming to BIS 6392/1997 Table 17 (Rating PN16) and welded on both sides. The job includes prividing and fitting of nuts, bolts, gaskets etc as per site requirement. Rest specification as per cluase "15" of SBD Size:DN 80 Class: C

Cutting of hot dip galvanized G.I, C-Class pipe across the section by dint of pipe cutter/ gas cutter. The job also includes Providing and welding of M.S flanges to the two ends of pipe. The Thickness of flange shall conform to IS 6392 Part 1st Table-17. :Rest specification as per cluase "11" of SBD. The size of the pipe is DN 80 , Class-C

Fabrication, providing, fitting T - junction out of 1 mtr of pipe with length of 1 ft each arm The job includes all types of skilled labours, arrangement of power supply/ diesel Generator set etc required for the job including P/F of suitable size nuts bolts and R.I Gasket in the flanged joints Rest specification as per cluase "09" of SBD Size: 80mm Class: C class

Providing and fitting of, Ductile Iron double flanged, non-rising spindle soft seated glandless gate/sluice valves as per IS14846 for regulating the water supply outside the pumping units . The body and bonnent of the valve shall be of ductile iron, wedge with fully vulcanized EPDMrubber(Approved for drinking water) and NBR seal. The Gate/Sluice valve shall be compatible forburied applications and shall be safe to install in both horizontal and vertical positionsRest specification as per cluase "12" of SBD. Size: DN80 PN:1.6/16

Providing and fitting of Ductile Iron double flanged, Slanted seat swing check valve( NRV) as per IS 5312. The body shall be of ductile cast iron with fully encapsulated vulcanized EPDM rubber(Approved for drinking water). Rest specification as per cluase "13" of SBD. Size: 80mm PN: 1.6/16

Providing, fitting, testing and commissioning of ARV (Air Release valve) as per IS 14845 to be fitted to G.I risingMain. The ARV Shall have the following specifications: - i. Valve type - single chamber, single orifice. ii. End connection - flanged ends to IS 1538 iii. Working temperature - 70oc to 550 c iv. Test pressure - body / seat 2.5 x PN v. Sealing ring - EPDM vi. Construction -ductile iron with stainless steel floats vii. Coating - epoxy with corrosion resistance Rest specification as per cluase "14" of SBD. size = DN 50 , PN 1.6/16

Providing and fitting of M.S 4 inch hinges -6 no and M.S handle heavy -8no., Anchor bolts with nuts (M16) of 0.3 m long = 04 No. Metallic strip (350mm×50mm×3mm) = 02 No.

Fabrication of gantry mechanism/CGI Shed /angle iron sleeping bed by way of providing Structural steel in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete welded

Providing, installation and testing of manual type triple spur gear chain pulley block along with monorail geared travelling trolley having following features Gears:- The hoist shall have precision machine case Hardened alloy steel gear mounted on bearings and housed in a dust proof gear box. The lubrication of gears should be of high viscosity and temperature for longer life of gears. Load Chain:- The load chain be made of high tensile alloy steel having wear resistance and greatest mobility. Rest specification as per cluase "24" of SBD: Make = Reputed make Capacity = 3 ton No. Of load chain falls = 2 or above Min. Height of lift = 6 M

Creation of pope mounted, outdoor type Electric Sub Station by way of S/I/T/C of 11/0.433 KVA , 3 Phase Distribution Transformer with Bimetallic Terminal connectors Energy level -2 Aluminum wound Specifications conforming to IS : 1180 (Part 1) 2014 with latest amendments Type of cooling: ONAN. complete Specification as per Clause- 26 Of SBD Rating: 63 KVA HT Transformer, 3 phase (Level 2).

Providing and fitting G.I Channel /Angle/ Flat of sizes including clamps

Supply, Installation, Testing and commissioning of Polymeric Gang operated Air break switch, outdoor type, triple pole, suitable for vertical installation, single break provided with locking arrangement at both ON and OFF position consisting of HT post double insulator, copper or copper alloy high pressure heavy contact assembly, rod with bearings , operating handle and 2 length of 32mm dia. GI pipe conforming to IS 1818 1961, 06 No. of insulators, rated voltage 11KV 200A complete as per IS specs.

Supply, Installation, Testing and commissioning of 11KV polymer fuses Set Horn Gap 3-phase 200 A suitable for vertical installation .

Supply, Installation, Testing and commissioning of Gapless Surge arrestor station class, 10KA, 9KV, LA With polymer housing , Station Type .

Supply and fitting of 11 KV polymeric composite pin insulator 12 KV, 5KN, Lighting impulse 75KV Positive, and 80 KV Negative, creepage distance 320 mm

Supply, installation, errection of 9 mtrs long H.T pole of specifications ST- 410 (sp-33). The job further includes drilling of holes for installation of various accessories .wherever required. The job further includes GI wire earthing of pole as per REC standard.

P/F of Galvanized nuts, bolts of various sizes as per site requirement.

P/F Danger Plate with clamps

Providing and fixing G.I Barbed wire for anti climbing

Providing and fixing of anti climbing devices with clamps

Providing and fitting of Galvanized stay set with 50 X 8 mm Stay Clamp , Guy insulator (2no.), Anchor plate (200X200X6mm) , nuts and bolts , 2 N0- turn buckle , 1.8 m long , 16 mm diameter solid G.I stay rod & 7/3.15 mm dia. G.I stranded wire complete.

Painting of poles Red oxide

Painting of poles Aluminum paint

Providing and fitting of ACSR as per IS 398 (part-2) 1996 for 50 sq.mm ACSR (Galvanised steel reinforced) for fitment of various accessories

Supply, Installation and Testing of 35 Sq mm XLPE Aluminum H.T cable (ABC type ) of 11 KV grade with following specs. Size (cross sectional area in sq mm) = 3×35 with reinforced wire Phases: Red, Yellow, Blue

Providing and fitting of Anchoring clamps comprising clamp body , plastic wedge, steel bill bracket , straps and buckles or nuts and bolts required for holding of 3 – Core , 35 Sq. mm H.T AB Cable.

P/F of 11 KV cable termination kit for connecting 35 Sq mm XLPE cable (ABC type) with the existing HT line near tapping point and HT transformer.

Providing and fitting of LT Distribution box for HT transformer with MCCB For incomer and SFU for out going circuits . Capacity of transformer: 63 KVA

Fabrication, Providing and fitting of MUG-20 Modular motor control panel of appropriate size fabricated out of 14 SWG sheet having required openings/vents and protection Class : IP-55 & fitted with accessories as under: Complete Specification as per Cluase - 43-d of SPD.

Providing, fitting, testing and commissioning of voltage stabilizer as per specifications below:Type of voltage controller: Manually operated copper wound, 3-phase, AC power supply multi step. Type of Regulator : Double plate type with electrolytic copper contacts. Input voltage : 250-400 volts.(3 phase) Output voltage : 400 ±10% volts. Frequency : 50 ±3 C/S. Windings : Electrolytic grade copper of adequate section, vacuum impregnated and Rest specification as per cluase "44" of SBD. Rating::40KVA

Providing and fitting of 3-Core flat submersible copper cable conforming to IS: 694 (Part 1st) – 1964 & IS: 694 (Part 2nd) - 1964 for Submersible Pumping Unit and other electrical Equipments . The cable connections terminal shall be fitted with copper thimbles of required size. Size: 10 sqmm

Providing and Fitting of 3 /3.5/2-Core, XLPE Armoured Aluminium Cable conforming to IS: 7089 part 1st as service line from the HT transformer to control panel including necessary thimbling, crimping, taping etc. NOTE:- The cable terminal ends for connection to switchgear at various requisite points shall be Al. Thimbles of dowel’s make and of appropriate size and connected by hydraulic crimp tool only. i) 50 sqmm, 3.5 core, LT, 1.1 KV

ii) 10 sqmm, 2 core, LT, 1.1 KV

P/I of earthing station for substation, LT panel, DG set and stabilizer comprising of company fabricated earthing electrode as per IS: 3043. The job includes Auguring of bore of required dia/depth for installation of electrode along with backfill compound mixed with soil and all other items required thereof for achieving the best result. The job includes connecting of electric gadgets through GI strip as per relevant standards. Safe earthing electrode size : 80 mm dia , Length : 2000 mm Back fill compound : 30 kg

Supply, installation of 6 kg co2 type fire extinguisher manufactured as per IS:15683 OF 2006 with IS mark and comply with DGMS(Approval) . The co2 extinguisher should be suitable for class B & C fire and also for fire involving electrical equipments. the cylinder used for fire extinguisher shall be approved by protroleum and explosive safety organization(PESO) as per gas cylinder rules 2004 and as per IS: 7285 of 2004. The body should be made of seamless steel (manganese) confirming to IS:7285 with IS mark and should be provided with squeeze grip nozzle and should be filled with co2 confirming to IS : 15222 of 2002 with certificate. The extinguisher shall be provided with manufactures test certificate and hydraulic test certificate by BIS from PESO.

Illumination of Premises: Providing and erection of 9 Mtr long Hot Dip Galvanized octagonal pole (single Section) with bottom 150mm, top 75mm wide, thickness 3mm with 70 Microns Zinc coating having inside arrangement for providing of power connection along with following items. 1) 3 Way Terminal Connector 20 Amp. 2) 3 No MCB 8 Amp. Rest specifications as per cluase "50" of SBD

Providing, installation, testing and commissioning of area lighting 120 Watt LED (Street Light Type) on top of octagonal pole vide item No.36 Having following specs: Input: 90-240 V 50 Hz Power Factor: >0.9 Colour Temperature: 4K - 6.5K Beam Angle: 120˚ - 170˚ Lumens: >12000 Operating Temperature: -20˚C to 60˚C Rest specifications as per cluase "51" of SBD

Providing, Installation and testing of 2KVA fully automatic voltage stabilizer with input voltage 70-240 V and output 220 V. The stabilizer shall be installed and connected to the electric circuit as per location provided by site incharge.

Supply, installation, Testing & commissioning of 1000VA Full Sine wave power inverter (Make: Reputed) including Providing / Installation of 12V, 180AH Tubular inverter Battery with trolley and cover. (Make: Reputed) with 2-core 6mm2 Cu wiring as per site requirement along with other accessories like SS-Combine (02 No’s), 3-pin plugs etc of reputed make for proper fitment and installation of the item.

Providing, laying & fixing with adhesive/bonding material of insulation rubber mats on the floor of the pump house, covering area around electro-mechanical machinery for safeguarding the life & limb of the workmen due to possible leakage of current & short circuit. The floor surface shall be made good & shall be free from dust, grease, foreign material & moisture free. The mats shall be as per IS 15652:2006 & shall have the following specifications: - Composition: Rubber (synthetic mats for electrical purpose) Thickness: - 2.5mm Size: - 1M wide. The rubber mats shall be accepted with manufacturers test certificate.

TOOL KIT For Maintenance: - The Tool Kit for maintenance shall comprise of the following and all the items as mentioned below shall be of : Providing of tool kit consists of following items i. Double ended Spanner (Chrome plated) of size in mm 6/7,8/9,10/11,12/13,14/15,16/17,18/19,20/22,21/23,24/26,25/28, 24/27, 30/32 each – 02 no. rest specifications and quantity as per clause - 56 of SBD

Providing and fitting of 19 mm thick multilayered ply sheet of size 6 x 3 feet , 2 nos including cutting , fixing all complete including painting of the play sheet by one coat of primer and two coats of enamel paint

a) Providing of good quality bedding for night stay/Shift consisting of: - i) Mattress with warm cover size 6'x3' (6Kg)- 02 No’s rest specifications and quantity as per clause-57 of SBD

Providing of solar/ electrical lantern chargeable on both solar & electrical 220v supply.

Providing of bamboo ladders 18 feet long along with 15 feet long Link rods and HT Glove pair (01 No each)

Providing of 1 KW heat convector for operators for winter season.

Providing and fitting of 01 No. LED (scroll type) sign board fabricated out of stainless steel and metal showing the names of water supply scheme and the Department. Size: 6’×1’6”= 9 sft

Providing and fitting of 01 No. angle iron/sheet metal board duly painted showing various specifications of the mechanical and electrical equipments installed at site of appropriate size.

Providing ridges or hips of width 60 cm overall with plain G.S sheets fixed with polymer coated J- Or L- hooks , Bolts and nuts 8 mm dia. G.I limpet and bitumen washers complete 0.63 mm thick with zinc coating not less than 275 gram/sq.m

Providing and fixing plain eaves boarding 2nd class Kail wood (250 x 32 mm nomonal size)

Providing and fixing of PUF Enclosure in Walls, Ceiling ridges etc made up of 60 mm thick rigid PUF, CFC free with profile surface on one side, conforming to IS-12436-88 with subsequent amendments having density of 40±2 kg/m3 sandwiched between 0.5 mm pre-painted Galvanized steel sheet as per IS-14246-95 with subsequent amendments with 18-20 microns of Exterior Polyester Coating of white color on epoxy primer on both sides. The basic substrate is Gr-120 Hot dip Galvanized steel. The panels are made by continuous line and are joined together by means of Tongue-n-groove joint system. The joints shall be air-tight by using proper sealant (like silicon PU foam etc). The PUF panels have closed cell content of 90-95%; Thermal Conductivity of 0.023 at 10W/mK; Compressive strength of 2.1 Kg/m2 (at 10% deformation); Water vapor permeability 0.08-0.12 gm/h_m2; Self-extinguishing fire property make: confirming to IS Code

Providing corrugated G.S Sheet roofing including vertical/ curved surface fixed with polymer coated J or L Hooks , bolts and nuts 8 mm dia. diameter with bitumen and G.I limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal /vertical or curved surface) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.50 mm thick with zinc coating not less than 275 gram/m2

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) powder coated aluminum (minimum thickness of powder coated 50 microns)

Providing and fixing 12mm thick pre laminated particle board flat pressed three layer or graded wood particle board (conforming to IS:12823 Grade-I type-II) in paneling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.

Providing and fixing aluminum casement windows fastener of required length for aluminum windows with necessary screws etc. Complete Powder coated minimum thickness 50 micron aluminum

Providing and fixing aluminum round shape handle of outer dia 100mmwith SS screws etc. Complete as per direction of Engineer-in-charge Powder coated minimum thickness 50 micron aluminum

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in-charge. With floating glass panes of 4.0 mm thickness (weight not less than 10.00 kg / sqm)

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto .5 m in -All kinds of soil

Carriage of sand, stone aggregate by mechanical transport including loading, unloading and stacking (average distance-5km)

Carriage of soling stone by mechanical transport including loading, unloading and stacking (average distance-5km)

Carriage of cement/steel/CGI sheet/GI pipes below 100mm dia and other heavy materials by mechanical transport including loading, unloading and stacking (average distance -25Km)

(Part B) Pump House of WSS Aripal Lift (Adv. Cost Rs. 14,75,000/-)

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: All kinds of soil (1 meter from cutting edge).

Providing & Laying of stone soling (dully hand packed)including watering dressing and ramming with all carriages loading un-loading and stacking etc complete

Providing & laying in position cement concrete of specified grade excld. The cost of centring and shuttering all work upto plinth level(1:4:8 coarse sand 40mm nominal size crushed stone agg.)

Providing & laying in position cement concrete of specified grade excld. The cost of centring and shuttering all work upto plinth level(1:3:6 coarse sand 20mm nominal size crushed stone agg.)

P/L in position specified grade of reinforced cement cencrete excld. The cost of centring, shuttering, finishing and reinforecement-All work upto plinth level. 1:1.5:3 graded stone agg. 20mm nominal size

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°,landings, balconies, shelves, chajjas, lintels, bands,plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement with 1:1.5:3 ( 1 cement : 1.5 coarse sand : 3 graded stone aggregate

Brick work with FPS bricks of class designation 75 in foundtion & plinth in cement mortar 1:6 (1 cement, 6 coarse sand)

Extra for brick work in super structure above plinth level upto floor V Level(by manual means)

Centring and shuttering incld. Strutting, proping etc & removal of form work foundation

Walls any thickness

Reinforcement for RCC work incld straightning, cutting, bending, placing in position & binding all complete (Thermo-mechanically treated bars)

Providing wood work in frames of doors, windows, clerestory windows & other frames, wrought framed & fixed in position 2nd class kail wood

Providing & fixing panelled or panelled & glazed shutters for doors & windows and clerestory windows including ISImarked black enamelled M.S Butt hingeswith necessary screws excluding panelling Second class Kail ( imported wood )35mm thick

Providing & fixing decorative plywood B/S decorative veneer (Type 1) confirming to IS 1328 BWR type

Structural steel welded in built up sections, trussses and framed

Providing CGS sheet roofing fixed with polymer coated J or L hooks bolts & nuts 8mm dia with bitumen & GI limpet washers upto( a pitch of 60 degree) excld cost of perlins, rafters & tresses 0.63mm thick with zinc coating not less than 275g/sqm

Providing ridges of hips of width 60cm overall width plain GS sheets fixed with polymer coated J or L hooks bolts & nuts 8mm dia GI limpet & bitumen washers complete 0.63mm thick with zinc coating not less than 275g/sqm

12mm Cement Plaster on the rough side of single or half brick wall of mix 1:6(1 cement:6 fine sand)

Distempring with oil bound washable distemper of approved brand & manufacture to give an even shade New work (2 or more coats)over and incld. Priming coat with cement primer

Painting with ready mixed Synthetic enemal paint or approved brand & manufacture in all shades to give an even shade NEW steel work (Two or more coats)

Finishing walls with water proofing cement paint of approved brand and manufacture &of rqd shade to give an even shade New work (2or more coats)applied @3.84kg /10sqm

Providing glass panes 10kg/sqm (4mm thick)windows and clerestory window shutters (Area of opening for glass panes excld portion inside shall be measured)

Cement Concrete flooring 1:2:4 (1 cement: 2 coarse sand: 4 graded stone agg) finished with a floating coat of neat cement incld. cement slurry but excld the cost of nosing of steps etc complete 50mm thick with 20mm n/s stone agg crushed

Providing and Fixing glass strips in joints of cement concrete floors 40mm wide and 4mm thick

Providing & fixing of 40x5mm flat iron hold fast 40cm long including fixing to frameswith 10mm dia bolts nuts &wooden plugs and embedding in cement conc block 30x10x5cm 1:3:6mix (1cement:3coarse sand:6 graded st agg)20mm nominal size

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed, consolidated and grouted with fine sand including finishing the top smooth

Providing & fixing Hardware items complete 150 mm Tower Bolt

150 mm Handles

L Drop

Dry rubble masonry with hard stone in foundation & plinth using quarry stone with bond stones

Providing and fixing soil waste pipes (10Ft Long) 100mm dia PVC B Class

Providing and fixing vent pipes 100mm dia PVC B Class

PVC colour 100 mm

P/F of PVC floor trap with Jali

Providing and fixing G.I pipes B Class 20' Long compleate with G.I fittings including all necessary fittings like Sockets, Tee, Reducer etc15mm dia nominal bore

Providing & fixing water closet squating pan (English W.C Pan)with 100 mm and PVC "P"or "S" trap 10 ltr low leavel P.V.C flushing cistern of app make with manually controlled device with fittings Long Pan pattern white vitreous china W.C pan 580mm

Water storage tank PVC tripple layer of approved brand with all necessary fittings

Stain less steel heavy duty Bib cock long nose

Stain less steel heavy duty angle valve

PVC connections

P/F man hole cover with frame

P/F lighting points/Heating Pointsfan points with 1.5 sqmm/4 sqmm FRLS PVC insulated copper conductor in surface/recessed medium class PVC conduit with modular switch, modular plate suitable GI box all complete Heating points

Lighting Points

Carriage of Materials By MT from source to site of work. Stone agg. from for an avg lead of 20 km

Sand from for an avg lead of 20 km

Bricks from for an avg lead of 25 km

S T ELECTRICAL ENG WORKS PEERNAR TRAL