Construction of Cultural Centre Phey ( Under Distt Capex )

Earth work in excavation by mechanical means (Hydraulic excavator) in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Dumping stone excluding cost of stones. Horizontal on Level.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

Centering and shuttering including strutting, propping etc. and removal of form work for : Foundations, footings, bases for columns

Columns, Pillars, Piers, Abutments, Posts and Struts

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Suspended floors, roofs, landings, balconies and access platform

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished 50 mm thick with 20 mm nominal size stone aggregate

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windowscomprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profilesduly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process ofrequired length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriatedimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated)casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plasticcaps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusionwelded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixinghardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wallshall be filled with weather proof silicon sealant over backer rod of required size and of approved quality,all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes andsilicon sealant shall be paid separately). Variation in profile dimension in higher side shall be acceptedbut no extra payment on this account shall be made.For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth& width of profile shall be acceptable.uPVC profile should be tested by BSI(UK) & SKZ(Germany) @25000 weathering hoursCasement window double panels with S.S. friction hinges (350 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash / mullion 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 1.50 sqm).

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class Kail wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately)Second class teak wood 35 mm thick shutters

12 mm thick pre-laminated particle board (decorative lamination on both sides) grade -1, medium density flat pressed, three layer particle board FPT- I or graded wood particle board FPT- I, conforming to IS : 3087, bonded with BWP type synthetic resin adhesive as per IS : 848 and pre-laminated conforming to IS : 12823, Grade 1, Type - II marked :

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification Two or more coats on new work

Rough cast plaster upto 10 m height above ground level with a mixture of sand and gravel or crushed stone from 6 mm to 10 mm nominal size, dashed over and including the fresh plaster in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) and top layer 10 mm cement plaster 1:3 (1 cement : 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement. Ordinary cement finish using ordinary cement

Providing and fixing 50 mm thick extruded polystyrene rigid insulation board of required size betweencavity wall, complying with ISO 4898:2008 & ASTM C 578- 08b - type VI, having thermal conductivity of0.0289 W/m K as per ASTM C 578 (measured as per IS 3346), compressive strength of > 350 kPa listed asper ASTM D 1621, density of 34-36 kg/m3 as per ASTM D 1622, water absorptions < 1% by volume as perASTM D 2842, oxygen index of 24.1 to 28.1 listed as per ASTM D 2863, cell size 0.4 mm of dia (max) asper ASTM D 3576. Fire retardent property as per DIN 4102, Part 1 of class B2 and as per ASTM E84 classA, fixed with suitable water based adhesive and fastener, complete in all respect as per the direction of Engineer-in-Charge.

Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm)

Providing and fixing traditionally carved wood work (Shingstak) over doors and windows including all accessories as per the direction of the Engineer in-charge, complete with; 2nd class kail wood

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 300x16 mm

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc.complete : 125 mm

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing

complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : Light shade pigment using white cement

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately) Size of Tile 600x600 mm.

Providing and laying gang saw cut 30 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1 cement : 5 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge. With granite stone of colour black, cherry/ruby red of area less than 0.50 sqm.

Providing & fixing upto floor five level precast cement concrete solid blocks including hoisting and setting in position in cement mortar 1:3 (1cement:3 coarse sand), cost of required centring, shuttering and curing complete1:3:6 (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20 mm nominal size)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimetre channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimetre of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimetre channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimetre channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated areawith perforation size and pattern as approved by the Engineer-in-charge and as per manufacturer'sspecification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.61

Carrage of mechanical Cement / Steel …................. 15 km

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever requiredOrissa pattern W.C. pan of size 580x440 mm with integral type foot rest

Sand ….......................... 15 km

Supplying and fixing of 1.1 KV PVC insulated and PVC sheathed XLPE at power cable of following sizes on surface / surface cables tray , 0.50 mtr below ground level etc. as required including carriage upto site of work ( Make as per annexure enclosed) 150 Sqmm 3.5 core Armoured

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

Aggregate ….....................15 km

Providing and fixing soil, waste and vent pipes PVC 100mm @ 6kg/rm

Providing and fixing CP brass towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arangement of approved quality colour and make (Prayag or equivalent)600mm long towel rail with total length of 645 width, 78mm wide and effective high of 88mm, weighing not less thant 190gms.

Providing and fixing CP brass toilet paper holder.C.P. Brass

Providing and fixing ready made 12mm thick wooden flooring of approved brand of company Action Tesa Green panel including cutting carriage beading all complte job. AC - 4

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 453x357mm

PVC 75mm @ 6kg/rm

Providing and fixing 100 mm sand cast iron grating for gully, floor or Nahani trap

Providing and fixing P.trap for English type w.c with washer and m.s claps complete job

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 32 mm dia

100x100x100 pvc as per

Providing and fixing vitreous china dual purpose closet suitable for use as squatting pan or European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: White vitreous china dual purpose WC pan with white solid plastic seat and lid with white vitreous china flushing cistern and C.P. flush bend.

32 mm dia nominal bore

40 mm dia nominal bore

Providing and fixing double equal plain junction of required degree 75x75x75 pvc as per

Providing and fixing uplasticised PVC connection pipe with brass unions30 Cm length 15mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixerand gyser points _of approved make conforming to IS : 8931 15 mm nominal bore

Providing and fixing C.P. brass close hole basin mixer piller tap of approved quality and make, weighing not less than 1.970 kg. 15 mm nominal bore of standard back type.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank lSI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid lSI license].

Making connection of PPR. distribution branch with G.I.main of following sizes by providing and fixing tee,including cutting and threading the pipe etc. complete.20 to 32 mm nominal bore

Providing and fixing C.P brass bib cock of approved quality conforming to IS :8931 15 mm nominal bore

Providing and fixing pvc gate valve with complete jod 32mm dia.pipe.

Providing and fixing heat tape 30watts of multi layer including wiring over pipe line in spring shape all complete job

Providing and fixing thermocold flex over pipe line for insulation all complete job

Providing and fixing of puff insulation including covering with wire meshing and aluminium sheet of 0.6mm thick complete job32-40mm dia

Providing & fixing of insulation of water storage tank of with nitrile sheet , tapping with cello tape, Rockwool6 inch per side , wire mesh,polythene, aluminium sheet 26 guage cladding with dia complete job 19mm thick nitrile sheet.

Providing & fixing automatic timer 30 to 33 watt incl.all complete

Waste coupling 38mm of 83mm length and 77mm breadth, weighing not less than 60gms.

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes SOR 7.4 UV stablized and anti-microbialfusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fitings 1/C fixing the pipe with clamps at 1.00m spacing. This includes cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-charge. (concealed work including cutting chases and making good the walls etc.) 20mm OD nominal bore

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with thefollowing sizes of FRLS PVC insulated copper conductor, singlecore cable in surface/ recessed medium class PVC conduit asrequired. A ) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

b ) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

c ) 2X 10 sq. mm + 1X 6 sq. mm earth wire

d ) 4 X 16 sq. mm + 2 X 6 sq. mm earth wire

1x2.5 sqmm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. ( FOR INVERTOR) 1x 1.5 sq.mm

3 pin 5/6 A socket outlet

Telephone Socket outlet

TV antenna socket outlet

Bell push

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 No.s 3 pin 5/6 A modular socket outlet and 2 No.s 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excludin modular plate etc. as required a) 5/6 A switch

b ) 8 way (4 + 24), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. A ) Single pole 6 /16 amp

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. a ) 25mm

Supply, installation , testing & commissioning of GI Electrode Earthing with 84mm dia and 3 meter length , with 3mm thick the electrode should be hot dip galvinised . The GI Electrode shall be pre filled with cristaline Conductive Material ( CCM ) . The GI electrode shall be surrounded with BEE MOIST compound to provide maximum contact between the electrode and compound should be eco - friendly GI Electrode Earthing should be eco - friendly GI Electorde Earthing should be maintinance free and does not require regular manual addition of water . The earthing pit should be covered with PVC cover.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at

Providing and fixing 25 mm X 5 mm

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) a ) 6 way (4 + 18), Double door

G.I. strip on surface or in recess for connections etc. as required.

On load Change over switch 250 Amp

Supplying and fixing following rating and breaking capacity and pole MCCB with thermagmetic release and terminal spreaders in existing cubical panel board including drilling holes in cubical panel making connections etc as required MCCB FP 400 Amp 50 KA

Fabrication, supplying , installation testing and commissioning of following pannel made out of 2mm thick M.S sheet , floor mounted , vermin & dust proof, indoors , duly painted with provsion for fixing of1 nos incomer MCCB, , MCCB type change over switch - 1 No including supply and fixing 2 set of Aluminium bus bar and strip for housing MCB,s 24 Nos , MF Digital Meter and other allied accessories as required ( Make as per annexure)

Supplying and fixing of following rating 240 /415 Volt " C" series miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connection , testing and commissioning.( Above to 32 Amp) a ) SPN 63 Amp

TPN 63 Amp

Supplying and fixing of 120 watt LED Street Light complete with GI pipe bracket duly embeded along the parapet /wall. Wipro LR02-132-XXX-57-G2 or equivalent approved make

20 watt LED tube light fitting. LL20-221-XXX-65NE3 of wipro or equivalent make and model Philips/Crompton Greaves.

Supplying and fixing of Angle / Baten Holder with 9 watt LED Lamp polycarbonate including making complete connections etc. as required. ( Make as per annexure enclosed.)

Supplying and fixing of following electrical items suitable for operating on 240 /230 volts AC, 50 HZ supply , including connection etc. as required. Exhaust fan 250mm size ( Heavy duty) CG transair or equivalent approved make

Supplying, installation testing and commissioning of LED 2'x2' recess mounted fixture that delivers atleast 3000 lumens and wattage not more than 36 watt. The luminaries shall have a CRC a power coated body and a high efficiency diffuser. WIPRO CRCO10 RO 38HP57GL OR equivalent approved make.

Supply and fixing LED type down lighter 12 watt

Supply and fixing LED type down lighter 15 watt