GE(S)BTD TOKEN NO 38 OF 2021-22 SPECIAL REPAIR TO OR MARRIED ACCN OF BLDG NO. P 53(1 12) AT GOVIND ENCLAVE AND SEWAGE PIPELINES AND SEPTIC TANKS UNDER AGE BR I AND AGE EM IV UNDER GE (SOUTH) AT BATHINDA MILITARY STATION

Amount

Excavation over areas, not exceeding 1.5 m deep and getting out in soft/loose soil complete all as specified and as directed.

Excavation over areas, exceeding 1.5 m deep and not exceeding 3.0 m deep and getting out in soft/loose soil complete all as specified and as directed

Excavation over areas, exceeding 3.0m deep and not exceeding 4.5m deep and getting out in soft/loose soil complete all as specified and as directed

Excavation over areas, exceeding 4.5 m deep and not exceeding 6.0 m deep and getting out in soft/loose soil complete all as specified and as directed

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 mtr in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/losse soil complete all as specified and directed.

Excavating in trenches, not exceeding 1.5 m wide and exceeding 1.5 mtr but not exceeding 3.0 mtr in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/losse soil complete all as specified and directed.

Material and labour for cement concrete (1:4:8), type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete and sub base in floors etc complete all as specified and as directed.

Material and labour for loose filling with broken bricks of sub class B old size of gauge 80 to 150 mm in soakage pits, soakage wells complete all as specified and as directed .

S & F 'in repair' 15mm bore, chromium plated stop valves, cast copper alloy,screwed down,high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S & F 'in repair' 15mm bore, chromium plated concealed type stop valves, cast copper alloy,screwed down,high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S & F in repairs 15mm bore pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with o without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F 'in repair' brass chromium plated shower rose 125 mm of size with arme and with or without swivel joints to steel pipe or union complete all as specified and directed

S & F in repair PVC connection 15 mm size with brass nuts of length 450 mm of approved quality complete all as specified and directed.

S & F in repairs vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm white, with integral foot rests including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor and fixed complete all as specified and directed.

S&F 'in repair' vitreous china wash basin, white, flat back, size 450 mm x 300 mm fixed on and including cast iron cantilever bracket 32 mm dia brass waste coupling and including fixing of tap, waste fitting and union complete all as specified and directed

S & F sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x460mm bowl size 410mm x330mm x160mm including waste fitttings and LDPE pipes complete all as specified

S&F stainless steel plate racks of size 900x600x250mm and thickness of SS strip of 1mm fixed wall etc. complete all as specified and directed .

Cutting holes in brick walls built in cement mortar including making good dismantled portion in CM (1:3) or cement concrete (1:2:4) type B-1 exceeding half brick but not exceeding one brick complete all as specified and directed

Material and labour for 50 mm thick cement concrete (1:2:4), type B-1 using 20 mm graded stone aggregate as in floor finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for 25 mm thick cement concrete (1:2:4), type B-1 using 20 mm graded stone aggregate as in floor finished even and fair without using extra cement complete all as specified and as directed.

Material and labour for Salt-glazed stoneware gully traps of size 150x150mm, square or round mouthed, type 'P' complete all as specified and as directed.

Cutting into existing manholes / septic tank for connecting new drains of size 100 mm, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B-l smooth finished, and reforming benching as required complete all as specified and as directed.

Providing and fixing SFRC (Steel Fibre Reinforced Concrete) Cover and frame (heavy duty HD-20 grade designation) internal size 590x590mm & External size of frame 800x800x100mm including manhole cover having size 590x590x50mm thick and fixed over earthing manhole after demolition of PCC coping & manhole cover & set in CM 1:4 including benching in PCC 1:2:4 and finishing smooth complete all as specified and directed.

M&L PCC 1:2:4 type B-2 using 40mm graded crushed stone agg for foundations, filling & mass concrete, sub-base & sub-floors, etc. complete all as specified and directed.

S & F in repair PVC valveless, syphonic action type flushing cistern 10 ltr capacity, low level, with inlet ball valve, float and handle including brackets, PVC bend long type and connectin to flush pipe of any size and pattern complete all as specified and directed.

S&F in repair white flush pipe of polyethene of low or high density or PVC, 32mm dia, 90cm long for low level cistern and fixed complete all as specified and directed.

S & F in repairs CP grating (with or without waste hole), 125mm size, fixed on floor/nahani gully trap traps etc complete all as specified and directed.

S & F in repairs drapery rod (conduit) of dia not less than 25mm duly powder coated of shade as decided by Engr-in-Charge incuding ABS plastic finials of approved shade and including standard MS poder coated brackets fixed to walls with rawl plugs and steel screws complete all as specified and directed.

S & F in repairs brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S & F in repair 15mm bore chromium plated fancy type brass bib tap quarter turn, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

Dismantling and disconnecting of existing CI soil vent pipe 100 mm bore fixed to wall, laid in trenches incl all fittings & accessories complete all as specified and directed.

Dismantling and disconnecting of existing CI soil vent pipe 75 mm bore fixed to wall, laid in trenches incl all fittings & accessories complete all as specified and directed.

S & F cast iron soil waste and vent pipe 75mm bore with or without ears fixed with chemical cement joints fixed to walls with and including fixing clamps, complete all as specified and directed.

All as per item No.34 but except pipes

S & F cast iron soil waste and vent pipe 100mm bore with or without ears fixed with chemical cement joints fixed to walls with and including fixing clamps, complete all as specified and directed.

All as per item No.36 but except pipes

S & F cast iron soil waste and vent pipe 100mm bore with or without ears fixed with chemical cement joints laid in trenches or in floors complete all as specified and directed.

S & F in repairs CI bends any radius, 100mm bore, diminishing pieces or tapers, etc with oval access doors, complete all as specified and directed.

S & F in repairs CI bends any radius, 75mm bore, diminishing pieces or tapers, etc with oval access doors, complete all as specified and directed.

S & F in repairs 100mm bore CI branch pieces, single ( equal or unequal) ordinary or inverted (spigot or socketed type) or with parallel branches with oval access doors complete all as specified and directed.

S & F in repairs 75mm bore CI branch pieces, single ( equal or unequal) ordinary or inverted (spigot or socketed type) or with parallel branches with oval access doors complete all as specified and directed.

S&F in repairs cast iron oval access doors of 75mm bore with rubber washer packing & bolts & nuts as required complete all as specified and directed.

S&F in repairs cast iron oval access doors of 100mm bore with rubber washer packing & bolts & nuts as required complete all as specified and directed.

S & F in repair 100mm cast iron sanitary connection socket to fit WC outlet complete all as specified and directed.

S & F in repair 100mm bore cast iron cowl complete all as specified and directed.

Taking down or up 15 mm bore steel tubing and connection for refixing or removal complete all as specified and directed.

Taking down or up 20 mm bore steel tubing and connection for refixing or removal complete all as specified and directed.

S & F GI tubing medium grade with all fittings and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm complete all as specified and directed.

S & F GI tubing medium grade with all fittings and fixed to walls & ceilings or laid in floors, bore of pipe 20 mm complete all as specified and directed.

Refixing old GI tubing 15 mm bore pipe and connections including cleaning in new or old position as on walls ceiling floors etc complete all as specified and directed. (i) Rates quoted by the contractor deemed to be included S & F new fittings as required.

Refixing only old GI tubing 20 mm bore pipe and connections including cleaning in new or old position as required on walls ceiling floors etc complete all as specified and directed. (i) Rates quoted by the contractor deemed to be included S & F new fittings as required.

S & F in repair ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of size 20mm bore ( weight 210 gms Minimum) complete all as specified and directed.

S&F in repairs three layers rotational moulded polyethylene water storage tanks (ISI marked) (cylindrical vertical top) hoisted and fixed in position 500 litre capacity complete all as specified and directed.

Taking down rain water pipe and eaves gutters (any size and pattern) including all fittings heads shoes bends swan necks etc complete all as specified and directed

S & F in repairs 110 mm bore PVC (SWR) of 6 kg/CM Square pressure fixed to walls with MS clamps of 25 x 3 mm flat iron and fixed with 75 mm long screw with PVC gutties not exceeding 1.80 mtr centre to centre distance complete all as specified and directed.

S & F 110 mm bore, PVC (SWR) fittings such as bends, tee, shoe etc; fixed to PVC pipes, complete all as specified and directed.

Dismantling water tanks and removing to store 500 ltr. Capacity.complete all as specified and directed

Supply and fixing mild steel framed work Framed work such as grills, gate, grantings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe290,Gde-E-165 complete all as specified and as directed

S & F framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc. not exceeding 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel') complete all as specified and as directed

M&L in repairs welding with thickness of metal not exceeding 6mm and not exceeding 2.5 cm in length etc complete all as specified and directed.

S&F in repair MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete as specified

S&F 200 mm long mild steel barrel tower bolts, ISI market stove enamelled block with bright bolt and fixed complete all as specified and directed complete all as specified and directed

S&F for MS sliding door bolt 250mm long stove enamelled black with bright bolt etc complete all as specified and directed

S&F 125mm long mild steel pressed handles, oval type ISI marked stove enamelled black complete all as complete all as specified and directed

S & F hasp & staple 100mm size, safety type, Aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S & F hasp & staple 75mm size, safety type, Aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/springs clips and S & F 3.0mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeeding 0.50 Sqm in each panecomplete all as specified and directed.

S & F 3.0mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeeding 0.50 Sqm in each pane complete all as specified and directed.

S & F 3.0mm thick figured glass, pin head type and glazing with oil putty in squares not exceeeding 0.50 Sqm in each pane complete all as specified and directed.

Taking down shutters of any description exceeding 1.00 sqm but not exceeding 2.00 sqm each and refixing in the same opening including easing and adjusting including renewal of unserviceable screws etc.complete all as specified and directed.

Dismantling boarding any description fixed in any position with rails including fillets complete all as specified and directed.

M & L for 18 / 19 mm thick prelaminated particle board (ISI marked), exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

M&L 2nd HW plain fillets, square, rectangular or triangular in section, wrought, secured with nails/brads or secured with screws, cross sectional area exceeding 3 sqcm and not exceeding 6 sqcm,complete all as specified and directed.

Taking down chowkats or frame with shutter (without taking off shutters from the frames) not exceeding 1.50 sqm each and removal from site complete all as specified and directed.

Taking down chowkats or frame with shutter (without taking off shutters from the frames) exc 1.50 sqm but not exceeding 4.00 Sqm each and removal from site complete all as specified and directed.

Taking down shutters of any description exceeding 1.00 sqm but not exceeding 2.00 sqm each and removing to store complete all as specified and directed.

S & F pressed steel frames size of frame 125 x 60mm for doors with one or more rebates including hinges, lock strike plate, fixing lugs, etc., (thickness of steel sheet shall be 1.25mm) and making good the plaster of wall in CM (1:6) complete all as specified and directed.

S & F pressed steel frames size of frame 105 x 60mm for doors with one or more rebates including hinges, lock strike plate, fixing lugs, etc. (thickness of steel sheet shall be 1.25mm) and making good the plaster of wall in CM (1:6) complete all as specified and directed.

S & F pressed steel frames size of frame 75 x 60mm for doors with one or more rebates including hinges, lock strike plate, fixing lugs, etc. (thickness of steel sheet shall be 1.25mm) and making good the plaster of wall in CM (1:6) complete all as specified and directed.

M & L for PCC 1:3:6 type C1 (using 20mm graded crushedstone aggregates) as in filling back of pressed steel door frames/chowkats and for fixing hold fasts, etc., complete all as specified and directed.

S & F for factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube fixed in opening complete as per specifications & drawing complete all as specified and directed.

S & F for 30 mm thick factory made solid panel PVC door shutter confirming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 guage thickness & size 19x19mm for stiles and 15x15mm for top & bottom rails MS frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded PVC `C' channel of size 30x50mm forming styles and 5mm thick 75mm wide PVC sheets for top rail lock rail and bottom rail on either side and 10mm (5mmx2) thick 20mm wide cross PVC sheet as gap insert for top rail and bottom rail panelling of 5 mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick PVC sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick PVC strip of 20 mm width is to be struck on the interior side of 'C' channel using PVC solvent adhesive complete as per manufacturers specifications & drawings complete all as specified and directed.

S&F 2nd class HW 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauge, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass, gauze, etc.; sizes of members of shutters as specified in SSR Part I Section 8, Clause 8.24 (a) complete all as specified and directed.

S&F 2nd class HW 35mm thick plain framed, factory made panelled shutter (two panel) with lock rail and panel of 9mm thick B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS-1003 (Part I) kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F for steel windows/ventilators with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars, dovetailed or welded, complete all as specified and directed.

S&F for steel windows/ventilators with side hung shutters including projecting type hinges with steel handle and steel peg stay complete without glazing bars, complete all as specified and directed.

Supply and fixing steel windows or ventilators fixed type with glazing bars complete all as specified and as directed .

S & F in repairs stainless steel wire cloth 0.36 mm nominal dia of wire and avarage width of aperture 1.4mm and fixed with tinned tacks to stainless steel wire stapple complete all as specified and directed.

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and avarage width of aperture 1.4mm and fixed with tinned tacks to stainless steel wire stapple complete all as specified and directed.

S & F mild steel Butt Hinges, 100 mm size, medium weight, cold rolled fixed with screws/welding to wooded/steel frames or chowkats, complete all as specified and directed.

Supply and fixing extruded aluminium anodised 100mm long butt hinges type B-21 with galvanised mild steel screws complete all as specified and as directed .

S & F 100mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S & F 150mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S & F 125mm long aluminium anodized handles cast type complete all as specified and directed.

S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flap (when open) 30mm complete all as specified and directed.

M&L for preparation of new steel and iron surfaces of any description exc 10 CM width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Dismanling floor, Stone slabs and tiles of any description or thickness in floors, aprons etc complete all as specified and directed.

M & L Non-skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed in CM 1:4 complete all as specified and directed.

M & L Non-skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed in CM 1:4 complete all as specified and directed.

M&L 40mm thick cement concrete type B-1, 1:2:4 (20 mm graded stone aggregate) as floors, sub-floors etc and finishing surfaces of concrete topping as even & fair or even & rough to receive the topping layer complete all as specified and directed.

M & L glazed ceramic coloured tiles 7mm thick 350mmx 250mm/450mmx300 mm size in vertical surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade etc complete all as specified including 10mm thick screed in CM 1:4 including dismantling of old tiles of any description etc complete all as specified and directed.

Supply and fixing in repair cast iron floor trap, 75mm dia with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate including CP gratting of suitable size complete all as specified and directed.

Supply and fixing in repair cast iron floor trap, 100mm dia with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate including CP gratting of suitable size complete all as specified and directed.

Material and labour for machine cut kota stone slab flooring 20-25mm thick over 20mm thick cement screed base in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

M&L for Kota stone slab 20 to 25 mm thick in riser of steps, skirting, dado and pillar set and jointed in 20 mm CM (1:6) with neat cement slurry and pointed in white cement paste pigmented to the match the shade of slab laid over rendering in cement mortar including rubbing and polishing complete all as specified and directed .

Demolition of re-inforced cement concrete of any description & in any position not otherwise specifically provided for, complete all as specified and directed.

Demolition of cement concrete of any description & in any position not otherwise specifically provided for, complete all as specified and directed.

M & L for reinforcement cement concrete (1:2:4) type B1 using 20mm aggregate as in slab supported on walls beams and columns in floor, roof, landing and in kitchen shelves and the like complete all as specified and directed

M&L for mild steel TMT bars 10 mm dia and over, cut to length bent to shape required including cranking, bending spirally etc and binding with mild steel wire not less than 0.9 mm dia as in reinforcement etc. complete all as specified and directed.

M&L for mild steel TMT bars 8 mm dia and over, cut to length bent to shape required including cranking, bending spirally etc and binding with mild steel wire not less than 0.9 mm dia as in stirrups complete all as specified and directed.

Formwork for rough finished surfaces to soffit of suspended slab such as roof slab, floor slab/chajjas /beams/colns/fins/facia and etc not exceeding 200mm thick complete all as specified.

Material and Labour for formwork to (rough finished surface of concrete) edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs exceeding 10cm but not exceeding 20cm wide complete all as specified and as directed.

S & F MS rungs of 20mm dia bar etc complete all as specified and as directed.

Demolition of brick work or stone / boulder masonary, built in cement mortar including all quoins, arches, pillars etc., complete all as specified and directed.

Demolition of RCC of any descrition such as Kitchen chimniy, chajja, shelves, OHT Tanks,Pilar,wall, column.beam etc and in any position not other wise specially provided for complete all as specified and directed (reinforcement cut as required to facilitate demolition)

Demolition of brick work of any type built in cement mortor in foul condition etc complete all as specified and directed

M&L brick work with sub class `B' old size bricks straight or curved on plan exceeding 6.0m mean radius built in cement mortar 1:6 complete all as specified and directed.

Material and labour for hardcore of broken stone of gauge not exc 63 mm, deposited, spread and levelled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for brick work built in cement and sand mortar 1:6 with sub class 'B' old size bricks straight or curved on plan exceeding 6.0m means radius complete all as specified and directed

M&L for brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, in half brick thick built in cement mortar 1:4, complete all as specified and directed

Demolition of cement concrete (unreinforced) not exceeding 15 cm thickness (below or above ground level)incl rubbish off the premises complete all as specified and directed.

M&L PCC 1:3:6 type C-2 using 40mm graded crushed/stone agg for foundations, filling & mass concrete, sub-base & sub-floors, etc. complete all as specified and directed.

M&L PCC 1:5:10 type E-2 using 40mm graded crushed/stone agg for foundations, filling & mass concrete, sub-base & sub-floors, filling of sunken floors etc. complete all as specified and directed.

Water proofing treatment to sunken slab and adjoining vertical surfaces as specified under:- (a) M&L rendering 10 mm thick in cement plaster (1:3) using coarse sand mixed with integral water proofing compound as per manufacturer's instruction trowel even and smooth with steel trowel on sunken surfaces (Note : WPC shall be measured and paid separately) (b) Applying first coat of chemical pidifin 2K(Dr Fixit) on cleared RCC surfaces @ 0.86 Kg/Sqm (Minimum) as recommended by manufacturer. (c) Provide a layer glass fibre mesh of size 2.25mm x2.25mm (45 GSM) over first coat of chemical Pidifin 2K as per manufacturers recommendation. (d) Applying second coat of chemical Pidifin 2K (Dr Fixit) @ 0.86 Kg/Sqm (minimum) layer glass fibre mesh of size 2.25mm x 2.25mm (45 GSM) as recommended by manufacturers.

Supply only Integral water proofing compound complete all as specified and directed. Make Dr. Fixit or any other equivalent make from list of make attached in tender documents as approved by GE.

M & L for applying a coat of cold bituminous [email protected] Ltr/Sqm over RCC/plastered roof surface and flashing etc followed by APP modified five layer ploymeric membrane minimum 3mm thick, minimum wt 3.00 kg/Sqm reinforced with polyester non-woven fabric (weighing not less than 150gms/Sqm ) manufactured by any manufacturer as per list of make in tender documents approved by GE, laid as per the manufactures instruction with side over lap of 75mm & end over lap of 100mm & tucked into the chases on vertical surfaces if required complete all as specified and directed.

M&L rendering 15mm thick cement plaster in CM 1:4 with water proofing compound and finishing top surface even & smoth as in roof slab /sunken floor , etc all as specified. (Note:- WPC shall be measured and paid separately)

Taking down cement or cement lime plaster of any description from brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specied and directed .

Material and labour for 15mm thick rendering in CM (1:4) on fair faces of brick work or concrete surfaces and finishing even & smooth but without using extra cement complete all as specified and directed.

Material and labour for 15mm thick rendering in CM (1:6) on other than fair faces of brick work or concrete surfaces and finishing even & smooth but without using extra cement complete all as specified and directed.

Material and labour for 15mm thick rendering in CM (1:6) on fair faces of brick work or concrete surfaces and finishing even & smooth but without using extra cement complete all as specified and directed.

Material and labour for rendering 5 mm thick in cement mortar in (1:3) on ceiling and finishing the surface even & smooth without using extra cement complete all as specified and directed.

Dismantling bricks laid flat or on edge and pointe in any mortar etc. (each layer) complete all as specified and directed.

M & L for rendering 5mm thick in CM 1:4 over 10mm thick additional setting/floating coat in CM 1:4 on concrete surfaces of wall chajjas, beams and ceiling etc and finishing the surface even & smooth without using extra cement

Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work exceeding 15 cm but not exceeding 30 cm in width or girth; including cutting to edges, all mitres and stopped ends, etc.

M&L for applying three coats of white wash on newly plastered surfaces on wall including preparation of surface, complete all as specified and directred

M&L for applying three coats of white wash on newly plastered surfaces on ceiling including preparation of surface, complete all as specified and directred

M & L for preparation of old surfaces of ceiling and applying one coat of white wash complete all as specified and as directed.

Material and Labour for painting to new wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces complete all as specified and as directed.

M&L for preparation of old painted wooden and wood based surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint of approved tint, quality, colour on these surfaces, complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint of approved tint, quality, colour on these surfaces, complete all as specified and directed.

M & L for preparing surfaces of steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint complete all as specified and directed.

Complete removal of existing treatment on Old Internal wall surfaces of any desciption, preparation of surface by Mechanised sander having suction vaccum Bag using Smart periodical methodology, complete all as specified and applying the following :- (a) M&L for wall care putty in two layers on wall surface and smoothening the surface with sand papers / Mechanised sanding etc preparatory to paint as directed complete all as specified (b) M&L for two coat of Oil Bound distemper of approved tint over a coat of primer on old prepared surface by using Airless spray/Roller complete all as specified. Note:- Contractor may use manual scraping tools for complete removal and surface preparation with prior approval of Engr-in-Charge in case of using of Mechancal equipement are not possible.

Preparation of New plastered Internal wall surface complete all as specified complete all as specified and applying the following:- (a) M&L wall care putty in two coats on wall surface and smoothening the surface with sand papers / Mechanised sanding etc prepatory to paint as directed complete all as specified. (b) M&L two coat of Oil Bound distemper over a coat of chalk whitening priming by using Airless spray/Roller complete all as specified. Note:- Contractor may use manual scraping tools for complete removal and surface preparation with prior approval of Engr-in-Charge in case of using of Mechancal equipement are not possible.

Preparation of New external plastered wall surface complete all as specified complete all as specified and applying the following:- (a) Applying wall care putty in two coats on wall surface and smoothening the surface with sand papers / Mechanised sanding etc prepatory to paint as directed complete all as specified. (b) two coat of exterior acylic emulsion by using Airless spray/Roller over and including a coat of acrylic emulsion external primer complete all as specified. Note:- Contractor may use manual scraping tools for complete removal and surface preparation with prior approval of Engr-in-Charge in case of using of Mechancal equipement are not possible.

Complete removal of existing treatment including filling depression of scraped surface with wall putty two coats 1.5mm thick each coat on Old external wall surfaces of any description, preparation of surface by Mechanised sander having suction vaccum Bag using Smart periodical methodology , complete all as specified and applying the following:- (a) M&L for two coats of exterior acylic emulsion by using Airless spray/Roller over and including a coat of acrylic emulsion external primer complete all as specified. Note:- Contractor may use manual scraping tools for complete removal and surface preparation with prior approval of Engr-in-Charge in case of using of Mechancal equipement are not possible.

M&L for 60mm thick machine pressed precast concrete interlocking pavers/tiles with grey cement and no pigment, confirming to IS 15658-2006 M-35 Grade,of any size & shape as directed in floors over & including 25mm thick sand screed beding/cushioning etc complete all as specified and directed

M&L for cement concrete 250mm x 250mm x 22mm thick, machine pressed over 15 mm thick in CM 1:4, jointed and grouted flush in cement mortar 1:3 mixed with 5% of crude oil by weight of cement on lime concrete complete all as specified and directed

M&L marble work (Udaipur green slabs) not less than 18 mm to 20mm thick (table rubbed and polished) as in cooking platforms and like in cement mortar (1:4) in pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade all as specified including rounding the edges over & including 15mm thick screed in cement mortar 1:4 complete all as specified and directed

Dismantling of brick tiles or terracing tiles, single layer on roof and disposal off retrieved material up to a distance of not exceeding 100m where directed, all as specified.

Demolition of Mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) including removing the demolished material upto a distance not exceeding 100 m away from site and disposal in low lying area complete.

M & L for wire brushing and cleaning top surface of roof slabs etc including washing the roof surface with water and making the surface free from mud etc complete all as specified.

M&L rendering 15mm thick in Cement mortar 1:3 ( average thickness) on roof surface including flashing and junctions of parapets etc finishing top surface even & fair including mixing with water proofing compound as per recommended ratio after brushing cement [email protected]/Sqm complete all as specified and directed. (Note:- WPC shall be measured and paid separately)

Material and labour for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement concrete 1:2:4 type B1 and finished the surface in cement mortar 1:3 complete all as specified and as directed by Engineer-in-Charge.

M & L for lime concrete in lime mortar ratio 1:3 using 40mm brick aggregate laid to slope/level over RCC roof as padding as directed complete all as specified and directed.

Material and labour for RCC M-25 design mix using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors,roofs, landings, chajja, balconies,canopies, deck slabs and in shelves and the like and in chajja etc complete all as specified and as directed. (NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Returning filling in, approved soft/loose soil, including spreading , levelling, watering and well ramming in layers, each layer not exceeding 25cm in soft/loose soil complete all as specified and directed.

Removing surplus excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

Material and Labour for precast cement concrete (1:2:4) type B1 using 20mm graded stone aggregate in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, kerb stones, shelves and similar articles with plain faces including necessary formwork and setting in mortar set in cement mortar (1:4) complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc. complete all as specified and as directed.

M & L for cleaning of existing sewage system/ pipe line of dia upto 200mm including cleaning of manholes (any type rectangular / sqaure / circular) located in different situations / sites, taking off the manhole cover 9CI of RCC) and placing in the same original position after and getting out iquid / sludge / solid contents from the manholes / sewage line and complete perfect function / running / flowing condition without any obstruction by removing all blockages in system using pressure jet cleaning technology & super succection machine only, making it fully functional to the entire satisfaction of Engineer-in-Charge including removing of all waste material out of MOD land, complete all as specified and directed. (Rate for getting out of liquid, sludge/ other materials from manholes / lines and removal is including in unit quated rate).

De- sludging from existing manholes septic tanks and soakage wells of any capacity size and depth including taking off the manhole cover, disposal of sludge etc out side MD land and placing in the same position after taking out sludge through mechnically sewage suction pump and dividely store in covered container etc complete and removing the sludge in covered van/trolly outside the MD land complete all as specified and directed Note :- Dewatering of existing manhole/septic tank will not be measured only solid material will be measured.

De-watering of existing soak wells of any capacity size and depth including taking off the manhole cover and placing in the same position after taking out waste sludge water through machanically sewage suction pump/honey sucker machine and directly store in covered container etc complete and removing the waste sludge water in covered van/trolly outside the MD land complete all as specified and directed

Dismantling of SWG pipe 150 mm dia for removal of blockage and replace only damaged SWG pipe of same dia including jointing with cement all around with PCC 1:2:4 including removing T&P of fitment required etc complete all as sepcified and as directed. (Note:- Earth work shall be measured and paid seperately)

Dismantling of SWG pipe 200 mm dia for removal of blockage and replace only damaged SWG pipe of same dia including jointing with cement all around with PCC 1:2:4 including removing T&P of fitment required etc complete all as sepcified and as directed. (Note:- Earth work shall be measured and paid seperately)

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar of any dia set in cement , laid in trenches including all fittings and accessories complete all as specified and directed.

Supply and fixing Salt-glazed stoneware drain pipes 100mm bore (internal) of grade 'A' laid in trenches and jointed etc. complete all as specified and directed .

Supply and fixing Salt-glazed stoneware drain pipes 150mm bore (internal) of grade 'A' laid in trenches and jointed etc. complete all as specified and directed .

Supply and fixing Salt-glazed stoneware drain pipes 200mm bore (internal) of grade 'A' laid in trenches and jointed etc. complete all as specified and directed .

Material and labour for PCC (1:3:6) type C-2 using 40 mm graded stone aggregates as in concrete bed of (SGSW) drain pipes of 100 mm dia( internal), laid to required slope including packing under and haunching against the sides of pipes after these are laid and tested complete all as specified and as directed . Note :- (i) Thickness of concrete bed below the barrel of pipe shall be 10 cm. (ii) Width of concrete bed shall be equal to outer dia of drain pipes (not of sockets / collar)

Material and labour for PCC (1:3:6) type C-2 using 40 mm graded stone aggregates as in concrete bed of (SGSW) drain pipes of 150 mm dia( internal), laid to required slope including packing under and haunching against the sides of pipes after these are laid and tested complete all as specified and as directed . Note :- (i) Thickness of concrete bed below the barrel of pipe shall be 10 cm. (ii) Width of concrete bed shall be equal to outer dia of drain pipes (not of sockets / collar)

Material and labour for PCC (1:3:6) type C-2 using 40 mm graded stone aggregates as in concrete bed of (SGSW) drain pipes of 200 mm dia( internal), laid to required slope including packing under and haunching against the sides of pipes after these are laid and tested complete all as specified and as directed . Note :- (i) Thickness of concrete bed below the barrel of pipe shall be 10 cm. (ii) Width of concrete bed shall be equal to outer dia of drain pipes (not of sockets / collar)

M&L flush pointing to brick tiles/brick laid flat as in roof, paving/floor etc in CM 1:3 mixed with 5% of crude oil by weight of cement and including raking out joints/pointing etc; complete all as specified and directed.

M&L for cement concrete type B0, 1:2:4 mix (using 12.5mm graded crushed stone aggregate) using water proofing compound along side wall adjoining to roof in concave shape complete all as specified and directed.

M&L for cement concrete type B1, 1:2:4 mix (using 20mm graded crushed stone aggregate) as in bedding, benching of manholes, copings, cills, bands, roof kerbs & surface channel and the like, including necessary form work etc. complete all as specified and directed.

M & L 75mm thick, cement concrete 1:3:6, type C2 (using 40mm graded crushed stone aggregate) as in floors, plinth protection, paths, etc and finishing top surfaces even and smooth (without using extra cement) complete all as specified and directed.

Taking down carefully existing unserviceable copper point wiring (light, fan, socket) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, etc and removing the retrieved materials from dismantling including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and directed.

Material and Labour for point wiring with multi stranded copper conductor FRLSH cable, 1100 volts grade PVC insulated and unsheathed of size 1.5 Sqmm single core in and including PVC concealed conduit not less than 20mm dia ( medium quality ISI marked) and conduit fittings and MS sunken box of suitable size covered with and including 3 mm thick bakelite laminated sheet top cover for one fan / light controlled by one switch including provision of 1.5 Sqmm PVC insulated unsheathed with single core, multi stranded copper conductor FRLSH cable as earth wire to common earth & connecting to earth dolly including cutting chasing of wall and making good disturbed surface in CM (1:3) and finishig the surface to match complete all as specified and directed .Note:- ( Switch and socket etc shall be measured and paid separately under approriate items of BOQ).

All as per item No 179 here in before but for socket outlet 5 pin, 6 Amp on same board complete all as specified and directed .

All as per item No 179 here in before but for socket outlet 5 pin, 6 Amp on independent board complete all as specified and directed .

All as per item No 179 here in before but for one light point controlled by two way complete all as specified and directed .

All as per item No 179 here in before but for call bell point complete all as specified and directed .

All as per item No 179 here in before but for one socket outlet 6 pin, 6/16 Amp with cable of 2.5 Sq mm, multi stranded copper conductor FRLSH cable on the independent board including provision of 2.5 Sq mm PVC insulated unsheathed with single core, multi stranded copper conductor FRLSH cable as earth wire to common earth & connecting to earth dolly complete all as specified and directed .

S& F switch piano flush type, 5 Amp 240 Volt, AC one way etc complete all as specified and directed by Engineer-in-charge.

Supply and fixing Switch piano, flush type, two way, 5Amps 230 V AC complete all as specified and as directed

S&F single pole bell push flush type switch, 5 Amps, 250 volts AC, complete all as specified and directed.

S&F one socket outlet 5 Pin 5 Amp 230 volts AC complete all as specified and directed. Note:- Switch and socket shall be of same make.

S&F one switch and one socket outlet 5 Pin 15 Amp 230 volts AC complete all as specified and directed. Note:- Switch and socket shall be of same make.

S & F stepped type electronic fan regulator suitable for 1200/1400mm ceiling fan flush type on the existing phenolic laminated sheet etc. as required complete all as specified and directed.

S & F for call bell AC, 230 Volt, complete all as specified and directed.

S&F mini mirror light indoor domestic mirror light luminarire with ploy carbonate cover suitable for 1x5 Watt, Havells cat Part No. LHEXBTP7UN1W005 or equivalent complete with all accdssories and ballasts including connections with twin core wire of suitable size complete all as specified and directed

Supply and fixing ceiling rose surface bakelite 65mm x 50mm, 3 terminals with back plate etc complete all as specified and directed .

Supply and fixing lamp holder angle/straight, polycarbonate body with back plate complete all as specified and as directed.

Supply and fixing 9/10 Watt LED bulb suitable for fixing in lamp holder complete all as specified and as directed.

S & F blanking plate etc complete all as specified and as directed .

S & F ultra bright integrated aluminium heat sink LED tubelight 20 W / 22 W with high efficacy suited for installation in existing T8 No. (TITANIANEO1213T8SSTL20WLED865SPC) of Havells. The tube will be fitted in regal batten for LED tube which is universal batten for T5 or T8 lamps, Cat Part no. (REGALBATTENT8UPTO1X22WSSBSWH) of Havells including electrical connections with 1.5 mtr long twin core round copper conductor cable of suitable size all as per Havells cat part No. LHEOAOP7UZ6W010 or equivalent model of approved make from list of make attached in tender documents complete all as specified and as directed.

Supply and fixing single phase, 50 hz, 230 volt exhaust fan of size 300 mm sweep( metal body) having BEE 5 star rating including making opening in wall for fixing exhaust fan and making good the disturbed surface by applying existing periodical treatment including making connection and providing 3 core copper conductor cable of suitable size complete all as specified and as directed .

Supply and fixing MCB, SP, 6 to 32 Amps, 'C' curve, 230 Volts, breaking capacity not less than 10 KA with over load and short circuit protection complete all as specified and as directed .

Supply and fixing MCB, SPN, 32 Amps, 230 Volts, breaking capacity not less than 10 KA with over load and short circuit protection,50 Hz including necessary attachment complete all as specified and as directed .

Supply and fixing MCB, SPN, 63 Amps, 230 Volts, breaking capacity not less than 10 KA with over load and short circuit protection,50 Hz including necessary attachment complete all as specified and as directed .

Supply and fixing MCB, TPN, 63 to 100 Amp, 230 Volts, 'C' curve breaking capacity not less than 10 KA with over load and short circuit protection,50 Hz including necessary attachment complete all as specified and as directed by Engineer-in-Charge

Supply and fixing sheet metal enclosures double door made out of CRCA mild steel sheet, flush mounted, acrylic door, 8 way, DB SPN 230 Volts, with 200 Amp rated bus bar, dust and vermin proof suitable for fixing MCB's and Isolators etc including taking down old unserviceable sheet metal enclosure complete all as specified and as directed .

Supply and fixing sheet metal enclosures double door made out of CRCA mild steel sheet, flush mounted, acrylic door, 4 way, DB TPN 230 Volts, with 200 Amp rated bus bar, dust and vermin proof suitable for fixing MCB's and Isolators etc including taking down old unserviceable sheet metal enclosure complete all as specified and as directed .

Supply and fixing sub main wiring with 2 single core cable multi-stranded PVC insulated FRLSH cable unsheathed 1100 volts grade with copper conductor of size 6 sq mm drawn in and including PVC concealed conduit (20 mm dia, medium grade), cutting of chases in wall / ceiling including earth continuity conductor cable of size 6 sq mm PVC insulated unsheathed copper conductor cable connected to common earth and earth dolly complete all as specified and as directed. Note : Three length of 6sqmm cable shall be measured as one length.

S & F surface mounted, decorative round bulk head luminaire comprising of high brightness LED lamp 10/12 Watt, 6000K polycarbonate with IP65 protection, the system wattage of fitting should not be more than 5 watt ± 10%, surge protection of minimum 2KV, power factor should be more than 0.90, cool while colour, total hormonic distoration (THD) should not be more than 15% lumen output should not be less than 900 lumens, total input voltage range 140-280V AC, colour rendering Index should not be less than 80 complete including all other accessories and fitting arrangement including electric connection connecting with using flexible copper wire twin core upto ceiling rose/conector. Make:- Crompon cat part No. LBHE-10-CDL or equivalent model of any make given in Appendix 'B' of tender documents, Cat Part No. as approved by GE.

S & F decorative wall light fixture made of polycarbonate suitable for retrofit 10 watt LED lamp, with min 900 lumen output base B-22 complete with & including one lamp 07W LED lamp(base B-22), 6500K, complete all light fittings connection all as specified and directed.

Supply and fixing LED street light fitting 45Watt 230 V AC outdoor type with high pressure die cast aluminum hosing toughened glass and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection ncluding fixing with GI/MS bracket made out of suitable size of light grade tube upto 1.5 mtr length bent to shape with 02 sets of MS clamps made out of minimum 3 mm MS flat iron with suitable bolt and nuts complete with making connection including twin core round copper conductor cable of 1.50 metre long twin core round copper conductor cable of suitable size and testing complete all as specified and directed.

Taking down serviceable/unserviceable ceiling fans 1200/1400mm sweep 230 V, AC, single phase from quarters, dismantling the ceilling fan and taking out complete rewinding (if unserviceable) the same with super enameled copper winding wire of existing gauge & size including thoroughly cleaning all the components of fan, oiling varnishing the fan with and including replacement of rusted/unserviceable nuts, bolts, split pin, rubber reel, flexible twin core copper cable of size 23/.00076 approximate one metre long for each fan, machine screws etc, refixing the repaired fan to respective qtrs complete all as specified and directed.

M & L for earthing with galvanized steel plate electrode 600 x 600 mm x 6 mm size directly burred in ground vertically earth pit not less than 2.25 meter deep below normal ground level with top edge of the earth plate not less than 1.5 m below normal ground level surrounded with coal dust and common salt filling in alternative layers of 15 cm thick each connected to and including GI earth wire 4 mm dia by means of GI nuts, bolts, check nuts & washers etc connecting to earthing test point, main switch board and including 15 mm dia GI pipe light grade for protection of earth lead from earth plate upto 5 mtr and 20 mm dia GI pipe medium grade connected with funnel having wire mess for watering purpose including necessary excavation and earth work, PCC (1:2:4) type B-1 (using stone aggregates) for earthing pit, 10mm thick cast iron cover with angle iron frame all as specified and shown in electrical plate No 3 of SSR Part-I and testing on completion.

Note:- If at site any nos of geyser, ceiling fan, exhaust fan, elecric meter is found before starting the work, The contractor shall be hand oer these items to Unit Rep in writing to avoid the last minute complicacies and refixing of electric meter is the sole responsibility of the contractor before handing over the site to user.

Note:- Net contract sum shall be calculated after deduction of Sch of credit amount to Rs.120268.

Aman Enterprises

M/s Verma Construction Company