SPECIAL REPAIR TO BLDG NO T15 AT BARABANKI AND PROVN ID DEFI CEILING FAN AT 7 KUMAON AND PROVN OF DEFI STAINLESS STEEL PLATE RACK IN BS MARG MD ACCN UNDER GE EAST LUCKNOW

Amount

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed.

M&L for brick work with modular fly ash bricks, straight or curved on plan exc 6m mean radius in CM 1:6 complete all as specified and directed.

Taking down of cement plaster in any description on brick or stone wall etc, incl racking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L rendering 15mm thick in patches in cement mortar 1:6 on other than fare face of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in patches in cement mortar in 1:4 on fare face of brick work or concrete surfaces even and smoothe without using extra cement & with using integral water proofing compound complete all as specified and directed.

M&L for two coats of Cement Base Paint over a coat of cement wash with portland cement slurry on newly plastered surfaces of wall including preparation complete all as specified and directed.

M&L for preparation of new plastered surface of walls and applying two coats of oil bound distember including preparity to plastered surface for distempering complete all as specified and directed.

M & L for preparation of old plastered surfaces of walls and applying one coat of Oil Bound distemper of approved tint, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 CM thick above or below ground level complete all as specified and directed.

M& L for cement concrete 75mm thick type 1:4:8 D - 2 using 40mm graded stone aggregate as in sub base to receive floor finish etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in-Charge.

M& L for Virified Ceramic tiles double charge/dark shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.42 sqm,n.exc 1 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6, complete all as specified and as directed.

All as per above item No. 12 but on vertical surfaces including 10mm thick screed plaser in CM 1:4 complete all as specified and directed.

S&F glazed ceramic (non skid) joint free edge cut coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm (400mmx400mmx8mm thick ) set and jointed in neat cement slurry and pointed in colour cement as in floor over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as dierected.

S&F glazed ceramic coloured tiles 7 to 8 mm thick 600 x 300mm size in vertical surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade. etc including 10 mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for broken stone or boulder hard core of gauge not exc 63 mm deposited spread and levelled in layers not exc.15 cm thick watered and rammed to a true surfaces complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C - 2, using 40mm graded stone aggregate as in plinth protection and finishing the surface even and smooth with using extra cement complete all as specified and directed.

M&L for chequred cement concrete tiles 20 cm x 20 cm x 25 mm thick set and jointed and pointed in neat cement slurry with grey cement and pigment in floors including 20 mm screed bed in CM 1:6 complete all as specified and directed.

Dismantling Asbestos Cement (Corrugated, Semi corrugated etc.) sheets in roof coverings including ridges, hips, valleys and flashings. complete all as specified and directed.

S & F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed with self taping screws as specified. complete all as specified and directed.

S & F Pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of colour having tensile strength of 550 Mpa as in roof covering/clading to wall for ridge and eaves board fixed with self taping screws complete all as specified and directed.

Taking down of chowkats or frames not exc 1.5sqm with shutters (with out taking off shutters from the frames). complete all as specified and directed.

Taking down chowkhats or frame exc 1.5 Sqm but n.exc 4 Sqm each with shutters (W/out taking off shutters from the frames). complete all as specified and directed.

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doo0rs etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

S & F Anodised aluminium powder coated frame work for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S & F Anodised aluminium powder coated door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges anodised aluminium snap beading screws etc. complete all as specified and directed.

M&L for powder coated (min 50 micron) aluminium three track sliding window with extruded profile of top bottom & side track for fixing 5.5mm thick tinted glass fitted with glazing clips and EPDM rubber in two shutters and fixing SS wire mesh in one shutter and powder coated deco grill including roller and handle, complete all as specified and directed by Engr-in-charge. Note:- (a) including 5.5mm thick tinted glass, SS wiremesh, Deco grill etc in this item. (b) Framed section 3 track size = 92x31.75x1.5mm (c) Shutter section size = 40x18x1.55mm

M & L for 4.8 mm thick sheet glass, ordinary quality in squares exc. 0.5 Sqm in each pane complete all as specified and directed.

S&F powder coating aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 Kg/m including necessary joining cleats glazing clips rubber packing, anodised aluminium sanp beading screw , anodised aluminium fittings such as peg stays 150 mm long (01 Nos) hinges type B-21 100 mm long (2 Nos) suitable handles (1 no) complete all as specified and directed..

S&F 18/19 mm prelaminated particle board, interior grade, prelaminated both sides with decorative choice laminations fixed with screws to timber frame work. complete all as specified and directed.

Preparing new surfaces of iron and iron based materials of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over and including a coat of red oxide complete all as specified and directed by Engr -in-Charge

Supply only integral water proofing compound complete all as specified and directed.

M & L deformed twisted/TMT bars 10 mm dia and over cut to length bent to shape required, including cranking and binding spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or secured with clips. complete all as specified and directed.

All as per item 33 above but 6 to 8 mm as in stirrups, spacers & binders. complete all as specified and directed.

M & L for RCC 1:2:4 type B1 using 20 mm graded aggregate for slabs support on walls beams and columns, in floors roofs landings balconies etc. complete all as specified and directed.

M & L form work for soffits and sides of suspended slabs such roof slabs, floor slabs, landing and similar works not exceeding 200 mm thick (horizontal or soffits) rough finished surfaces of concrete flat. complete all as specified and directed.

M&L for Granite 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 20mm thick screed in CM 1:4 including cutting, polishing, rubbring & moulding of edges complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking plateform and other similar situation complete all as specified and directed.

S&F PVC cabinate shutter as in kitchen with frame including shelves in required sizes at site made out of 18mm thick one side decorative lamination & other side balancing lamination sheet and provision of shutters made out of 18mm thick one side decorative laminated PVC sheet all required brackets stainless screws etc. The panels shall be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish including all necessary fittings as per site requirementand as per make and specification mentioned as per drawing and complete all as specified and directed. by Engineer-in-charge on site. Note:- Density of PVC solid sheet should not be less than 575 kg/cum.

Dismantling of timber scantling 40 sqcm and over in section in any position as in unframed work complete all as specified and directed.

S&F 2nd class hardwood scantling clean swan as in purlins rafters including wooden cleats etc complete all as specified and directed.

Dismantling textile covering incl frames (if any) and cover fillets in ceiling (measured flat and not girthed) complete all as specified and directed.

S&F GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre / intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900mm centre to centre with wire 4 mm dia and necessary cleats and steel expansion fasteners with and including ceiling section (not exc 1.2 m length ) of 5.5 mm thickness having kurled web of 50 and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm cenetre to centre and hangers 6 mm dia GI (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x3 mm size 60 min long complte all as specified including 10 mm thick POP (Gypsum anhydrous) board of size 1800mm x 1200 mm to flate surface over metal frame work and reinforced with cellulose fibre at different height or level to provide seamless finish complete all as specified and dirrected

Taking up or down GI tubing 15 mm bore pipe and connections including cleaning for re-fixing or removal to store complete all as specified and directed.

S&F GI tubing 15 mm bore medium grade galvanise with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm including cutting and chasing complete all as specified and directed.

Taking up or down GI tubing 20mm bore pipe and connections including cleaning for re-fixing or removal to store complete all as specified and directed.

S&F GI tubing 20 mm bore medium grade galvanise with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 20 mm complete all as specified and directed.

S&F in repair vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified and directed.

S&F in repair sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160m including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete, including taking down old unserviceable sink incl 40mm dia Waste coupling of PTMT (half or full threaded) .(Minimum weight 32mm-45gms/40mm-60 gms) complete all as specified and directed.

S & F in repair stainless steel Kitchen plate rack of overall minimum size 750 mm x 900 mm and 250 mm deep, with partitions for small/large plates etc made out of stainless steel 0.80 mm thick fixed with rawl plug and CP steel screws complete all as specified and directed.

S & F stainless steel Kitchen plate rack of overall minimum size 750 mm x 600 mm and 250 mm deep, with partitions for small and large plates etc made out of stainless steel 0.63 mm thick fixed with rawl plug and CP steel screws complete all as specified and directed.

S&F CP grating 125mm dia with waste hole (Minimium weight 40 grams) complete all as specified and directed.

S&F in repair PVC connection 450 mm long suitable for 15 mm bore GI pipe including CP brass nuts on both sides, complete all as specified and directed.

S&F in repair long body 15mm bore bib tap, cast copper alloy, chromium plated fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified & directed.

S&F in repair 15 mm dia chromium plated fancy type angle valve pipe with capstan head long screwed shank including cp cover plate etc complete all as specified and directed.

S&F in repair 15 mm bore CP brass Central Hole Basin mixture fixed to GI pipe complete all as specified and directed.

S & F in repair 15 mm bore brass CP wall mixer for mixing hot & cold water with provision for over head shower with arm and long bend pipe and wall flanged screwed down for iron pipe etc complete all as specified and directed.

S&F in repair hand shower (Health faucet) with 1 Mtr flexible tube with wall hook bracket etc, complete set of superior quality complete all as specified and directed.

S&F in repair CP shop dish fancy type fixed with SS screw on wall etc complete all as specified and directed.

S&F in repair toilet paper holder CP fixed complete all as specified and directed

S&F in repair PVC bath cabinet with 4 mm thick loocking mirror of overall size 560 x 410 mm fixed on wall etc complete all as specified and directed

S&F in repair glass corner self assembly, fancy type, made of 6 to 7mm thick sheet toughened glass of size 250x250mm, fixed with CP brackets, complete, all as specified and directed.

Supply & fix in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long. complete all as specified and directed.

S&F in repair CP brass tubular towel rail, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete all as specified and directed.

S&F in repair 40mm bore PVC low density (LDPE) pipe of pressure 6kg/Cm2 fixed to wall or laid in floor, complete all as specified and directed.

S&F in repair brass chromium plated shower rose 125 mm size without swivel joint including fixing to steel pipe of 15mm bore or union complete all as specified and directed.

S & F in repairs cast iron floor trap/nahani trap plan with grating of 100 mm size including jointing to waste pipe with cement joints etc complete all as specified and directed.

Dismantling of cast iron drain pipe jointed in lead joints or cement joints and taking out of under floors if required complete all as specified and directed.

S & F 100 mm dia cast iron soil waste and vent pipes sand cast in any length with or without laid in wall with cement joints complete all as specified and directed.

S & F 75 mm dia cast iron soil waste and vent pipes sand cast in any length with or without laid in trenches or in floor with cement joints complete all as specified and directed.

S & F in repairs 100 mm bore cast iron bends of any radius diminshing pieces or tappers (larger bore measured) complete all as specified and directed.

S & F in repairs 75 mm bore cast iron bends with acces door of any radius diminshing pieces or tappers (larger bore measured) complete all as specified and directed.

S & F in repairs 75 mm bore cast iron bends of any radius diminshing pieces or tappers (larger bore measured) complete all as specified and directed.

S&F 100 mm branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed by Engr-in-charge

S&F 75 mm branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed by Engr-in-charge

S&F in repair vitreous china floor/wall hung WC with flushing cistern, UF seat cover, hinges, accessories set of size 375 x 650 x 800/370 x 645 x 810 mm fixed to wall/floor with P/S trap complete as per manufacture's instructions. complete all as specified and directed.

M&L for 2nd class HW plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads exc 13 & n exc 25 sqcm etc complete all as specified and directed.

M&L for 12 mm thick plywood grade BWR type BB, fixed with screw to timber frame work block board interior grade having both sides commercial faces fixed with screws to timber frame work complete all as specified and directed.

M&L for 6 mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces, fixed with screwds to timber frame work complete all as specified and directed.

M&L PU polish on wooden wall surface/wood based material of any description width of girth including removing/cleaning and prepration of the surface including a coat of wood filler with two or more coats as approved complete all as specified and directed.

Complete removal of existing treatment from walls, preparation the surface of wall including cornices plasters etc and applying two coats of cement base paint (any colour as approved) on old treated surface of wall including preparation complete all as specified and directed.

M&L for gunniting to RCC works in column beams, slabs, chajja, facia, landing, balconies etc by removing/ dismantling of RCC (loose concrete) and cutting of steel bar including plaster cleaning of surfaces with wire brushes and applying epoxy, paint anti corrosive coating of minimum 40-50 microns thick with sikatop Armatec 108 or Colusal VL of MC Bauchemie to rusted steel reinforcement after removing cleaning all rust and supply and fixing welded steel wire mesh 75mm x75mm with 4mm dia steel wire as facies/drops and similar works etc and expoxy based or other equivalent suitable bonding against treatment to be carried out on old concrete surface with Sikadur 32 of Sikka. Nito bond EP of fosroc or equivalent (as per manufacturers instruction) to bond old and new concrete mixing @ 2% by weight of cement polycrete and providing gunniting with a minimum pressure of 2 to 2.5 Kg sqcm and applying 25mm thick gunniting in cement mortar (1:2) (one part of cement and two part of ghaghar sand) using ordinary port land cement of 43 grade over wherever required, complete all as specified and directed by Engineer-in-Charge. Note:-(i)After placing the additional reinforcement all concrete surface shall be thoroughly scrubbing with. (ii)Additional reinforced TMT bars where incorporated in work and including 20mm thick cement plaster in 1:4 (iii) Work to be carried out as in patches as directed by Engr-in-charge. (iv) Rate for steel scaffolding as directed to be included in quoted rate. (v) All demolished material removed from MOD land completely.

M & L preparation of newly plastered surfaces and applying three coats of white wash on walls. complete all as specified and directed.

S& F white colour triple layer rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and jointed in position all as specified in SSR Part-I (1000 ltr capacity) including dismantling of existing tank and providing all necessary fittings for connecting with pipe line, metal lockable cover. complete all as specified and directed.

S&F 20 mm ball valves high pressure of PTMT with epoxy coated aluminium rod & hihdesity plastec ball screwed for iron pipe and fixed. (Minimum weight 20mm - 210 gms) etc complete all as specified and directed.

Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc for taking credit including making good the disturbed surfaces to match with the existing complete all as specified and directed.

Material and labour for one light / fan point controlled by one, one way switch 06 Amp wiring with 1.5 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sq mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20 mm dia or higher, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing complete all as specified and directed.

All as per serial item No 87 here-in-before but one 3 pin, 06 Amp socket outlet point on independent board controlled by one, one way switch 06 Amp. complete all as specified and directed.

All as per serial item No 87 here-in-before but one 3 pin, 06 Amp socket outlet point on same board controlled by one, one way switch 06 Amp. complete all as specified and directed.

All as per Serial Item No 87 here-in-before but point wiring with 2.5 Sq mm single core FRLS cables and earth continuity wire of 1.5 Sq mm single core FRLS cable for one 3 pin 16 Amp socket out let point controlled by one, one way switch on independent board complete all as specified and directed.

S&F Switch Modular 6A single pole, one way, 1 module complete all as specified and as directed

S&F Switch Modular 16A single pole, one way, 1 module complete all as specified and as directed

S&F Socket, 6A - 2/3 pin combined 2 module complete all as specified and as directed

S&F Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and as directed

S&F Modular White cover plate with frame,12 module complete all as specified and as directed

S&F Modular White cover plate with frame,8 module complete all as specified and as directed

S&F Modular White cover plate with frame,3 module complete all as specified and as directed

S&F Modular Metal flush box 12 module complete all as specified and as directed

S&F Modular Metal flush box 8 module complete all as specified and as directed

S&F Modular Metal flush box 3 module complete all as specified and as directed

Supply and fix fan step regulator, 120 watt, 2 module complete all as specified and as directed

Supply and fix lamp holder, PVC / Polycarbonate type with back plate suitable for batten fitting complete all as specified & directed.

Supply and fix in replacement of decorative wall mounting type LED light fitting, 1 x 15 Watt, 230 Volt made up of Polycarbonate including shade, lamp holder, 9/10 Watts LED lamp B22 CDL etc and all accessories pre-wired including connecting up complete all as specified and directed

Supply and fix in replacement of integrated LED 2' x 2' round / square fitting 10 Watt, 6500K with IP 65 protection comprises of high pressure die cast aluminium housing, polycarbonate cover, etc complete all as specified and directed.

Supply and fix in replacement of LED security light fitting 25 watt, 5700K with IP 66 protection comprises of a pressure die cast aluminium housing, heat resistance toughened glass, LED lenses, surge protector, electronic driver, etc and all accessories pre-wired including connecting up with PVC insulated copper conductor cable 1.5 Sq mm, 3 core as required for connections and 32 mm bore light grade G. I. tube mounting bracket of 1.5 metre in length, bend to shape at 140 degree in ‘L’ shape and fixed to wall by means of 02 nos. of 40 x 5 mm flat iron clamps, nuts, bolts and washers etc complete all as specified and directed.

Supply and fix LED tube light fittings 1200 mm,20 W higher energy saving decorative ultra slim square profile LED lighting fixture with extruded polycarbonate enviromental friendly, energy efficient complete all as specified and directed

Supply and fix LED tube light fittings 600 mm, 10 W higher energy saving decorative ultra slim square profile LED lighting fixture with extruded polycarbonate enviromental friendly, energy efficient complete all as specified and directed

Supply and fix ceiling rose, 6 Amp, 250 volt, AC, ISI marked with three equal size terminals and PVC / Polycarbonate insulated body of 50 x 25 mm size complete all as specified & directed.

Taking down carefully ceiling fan of any sweep complete with all accessories, dismantling blades and deposit in safe custody of AGE E/M Yard-II for BER procedure complete all as specified & directed.

Material and labour for sub main wiring with 06 Sq mm nominal cross sectional area, two single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 06 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing including taking out the unserviceable sub main wiring complete all as specified & directed.

Material and labour for sub main wiring with 04 Sq mm nominal cross sectional area, two single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 04 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing including taking out the unserviceable sub main wiring complete all as specified & directed.

Supply and fix in replacement of industrial type SPN enclosure with a two pin and earth plug and socket complete with and including MCB, SP, AC, 240 volt of 20 Amp, 'C' curve 10 KA breaking capacity and flush to wall including all cuttings & chases etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed.

Supply and fix in replacement of sheet metal enclosure distribution board, double door, single pole and neutral, AC, 240 volt, 12 way, with 200 Amp rated copper bus bar and metal door with IP - 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed.

Supply and fix in replacement of sheet metal enclosure distribution board triple pole and neutral (VTPN),double door, AC, 440 volt, 04 way with 200 Amp rated copper bus bar and metal door with IP 54 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed and comprising of the following:- (a) MCCB, 125 Amp, 04 pole, AC, 415 Volt of 16 KA breaking capacity complete - 01 No. (b) MCB, SP, AC, 240 volt of 06 to 32 Amp, "C" curve, 10 KA breaking capacity - 12 Nos.

Supply and fix in replacement of MCB, SP, AC, 240 volt of 06 to 40 Amp capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Supply and fix in replacement of MCB, DP, AC, 240 volt of 32 Amp capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Material and labour for earthing complete with galvanised mild steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried vertically in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level steel earth plate connected with GI wire 04 mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15 mm bore light grade all as shown in elect plate No 3 on serial page No 497 of SSR part I - 2009 and connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150 mm thick around GI earth plate, GI pipe medium grade 20 mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover 40 mm thick in PCC 1:2:4 type B1 duly reinforced with MS Bars 6 mm dia at the rate of 75 mm centre to centre both way with 12 mm dia lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40 mm x 40 mm x 3 mm frame for pit cover including testing on completion complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed. by Engr-in-Charge

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1400 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed. by Engr-in-Charge

S&F exhaust fans, plastic body, ac, single phase, 230/240 v of size 250 mm sweep with louver and making connection with twisted copper flexible wire 23/0.076mm complete all as specified and directed.

S&F exhaust fans, heavy duty, ac, single phase, 230/240 v of size 300 mm sweep with louver and making connection with twisted copper flexible wire 23/0.076mm complete all as specified and directed.

Cutting walls any type, making holes for fixing of exhaust fan of any size or sweep and making good surface with fine plastering, finishing and colouring with existing colour matching complete all as specified and directed

Supply only LED bulb 9/10 Watts suitable for B22 white in colour complete all as specified and directed.

Excavation in trenches in any type of soil not exceeding 1.5 mtr wide and not exceeding 1.5 metre in depth for taking out of unserviceable under ground cable complete all as specified and directed

Returning, filling in, any type of soil and spreading, in layers not exceeding 25 cm thick complete all as specified and directed

Removal of surplus soil (any type of soil obtained from excavation) to a distance not exceeding 50 metre and depositing where directed & complete all as specified and directed

Supplying and laying bricks common brunt clay building bricks sub class B inclinding removing of old bricks complete all as specified and directed

M & L sand cushioning for laying of under ground cable all as specified and directed. ( Note:- punned down thickness shall be considerd for mesurement) complete all as specified and directed.

Supply, laying, jointing, testing and commissioning in replacement of 35 Sqmm 3.5 Core cable XLPE insulated , armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, laid in trenches,on pole complete all as specified and directed

M/s Ramesh Chandra

M/S KAUSHIK CONSTRUCTION

ANIL CONSTRUCTION

QUALITY CONSTRUCTIONS CO