repair renovation of toilet blocks (ladies and gents) at ground floor and first floor in the building of Gandhi Bhawan at CCS HAU, Hisar

Amount

Dismantling cement conglomerate/terrazzo floors 25 mm to 50 mm thick including concrete base. (HSR 8.25)

Dismantling white or coloured glazed tiles (to be carefully removed) (HSR 8.38)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size in foundation and plinth (HSR 10.41)

Cement conc. 1:2:4 with stone aggregate 20 mm nominal size for reinforced conc. Work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centering and shuttering, laid in position, complete in all respects. (HSR 10.82)

Extra over item Nos.10.79 to 10.94, if 1:1½:3 mix is used instead of 1:2:4. {HSR 10.95(a)}

Providing and laying four courses of water proofing treatment consisting of first and third course of blown type bitumen grade 85/25 applied hot at 1.6 kg per sqm for each course and second course of fibre glass R.P. Tissue and fourth and final course of stone grit 6 mm and down size or pea-sized grit spread at 0.006 cum per sqm including preparation of surface. (HSR 13.62)

Providing and lying cinder concrete in cement 1:15 (1 cement and 15 cinder) on terraced roofs & ( Ist storey) , laid to slope , including consolidating the same (HSR 13.66)

Base course of floors consisting of 100 mm thick cement concrete 1:8:16 and 100 mm sand or stone filling. (HSR 14.1)

Providing and fixing ceramic tiles/ anti skid tiles of size 400 mm x 400 mm or above size of approved make in flooring, laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles (HSR 14.91) Note : tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, JOHNSONS & RAK

10 mm thick cement plaster 1:4 on underside of ceiling (HSR 15.52)

Painting two coats with synthetic enamel paint in all shades on old wood work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint (HSR 16.5)

White washing two coats (HSR 16.47)

Steel reinforcement TMT bars FE-500 EQR/FE-500 D grade or more for RCC work, where no included in the complete rate of RCC incluidng straightening, bending, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position, complete in all respect for all heights/depths/storeys/basements etc. Note: Reinforcement shall be measured in length including hooks, if any, separtely for different diameters as actually used in work excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. (HSR 18.22)

Labour for laying, jointing, fixing and testing G.I./P.V.C./W.I. pipe lines and specials tees, bends, sockets elbows etc. inside building and testing etc. complete including cutting threading. {HSR 28.18(b) (i)} INCLUDING COST OF SPECIALS (i) 15 mm internal diameter of pipe line

(ii) 20 mm internal diameter of pipe line {HSR 28.18(b) (ii)}

(iii) 25 mm internal diameter of pipe line {HSR 28.18(b) (iii)}

Extra for fixing and jointing union couplings in G.I and W.I pipe lines. (HSR 28.21 (b) (b) 20 mm dia

(c)25 mm dia (HSR 28.21 (c)

Cutting holes up to 23 cm through stone masonry or brick work in cement walls for pipes and making good including repointing, replastering and finishing according to existing finish where required. (HSR 28.24 (a) (a) 11.43 cm thickness wall

(b) 22.86 cm thickness wall (HSR 28.24 (b)

Cutting holes up to 23 cm square for pipes in floor and roofs of cement concrete reinforced concrete or reinforced brick work and making good including repointing, replastering, replacing bitumen and colour or white washing where required. {HSR 28.26(b)} (b) 115 mm thickness of roof of floor

Fixing and jointing gun metal peet valves (heavy pattern) with hand wheels, on G.I pipelines laid in the ground or inside buildings including cartage from divisional stores or nearest railway station to site of works. {HSR 28.29 (b)} (b) 20 mm internal diameter

(c) 25 mm internal diameter {HSR 28.29 (c)}

Labour for laying, jointing, fixing and testing G.I./P.V.C./W.I. pipe lines and specials tees, bends, sockets, elbows etc. in trenches in the ground, cutting, threading and testing etc., complete. {HSR 28.19 (h)} (h) 80 mm internal diameter of pipeline

(i) 100 mm internal diameter of pipeline {HSR 28.19 (i)}

Making connection with the existing G.I branch main up to 40 mm size including cutting and threading pipe etc., complete excluding cost of tee and long screw, but including cartage of material to site. (HSR 28.34)

Providing and fixing in position best Indian make European type water closet suite with concealed ‘P’ of ‘S’ trap with or without vent (as approved by the Engineer-in-Charge) and all other necessary fittings as fully described in item No. 30.3 above (without cost of C.I. high level flushing cisterns) {based on HSR 30.6(i)} (White)

Extra over item no. 30.3 to 30.6 for providing and fixing best Indian make plastic hygenic seat with lid complete instead of hollow black or white plastic seat and lid. {HSR 30.13 (i)} (i) White plastic seat ( Solid)

Extra for providing and fixing 32 mm dia. G.I/ C.P flush pipe complete with accessories instead of 32 mm dia. Galvanised telescopic flush pipe with clips ( as required by the Engineer-in-charge) {HSR 30.15(b)} (b) 32mm dia C.P brass flush pipe

Providing and fixing in position best Indian make a range of three urinals large flat back or angular lipped front 610 mm high in vitreous china-ware with one no. 10 lit capacity best Indian make C.I automatic flushing cistern with fittings and flush pipe etc. complete as fully described in item no. 30.25 above. (HSR 30.27) Range of three urinal (i) white

Extra for providing and fixing vitreous automatic flushing Cistern including fittings and brackets of C.I. flushing cistern complete {HSR 30.37(b)} (b)10 ltr. capacity cistern (i) white

Extra for providing and fixing standard size C.P. brass flush pipe complete with fittings instead of G.I flush pipe complete (HSR 30.38) (iii)For a range of three urinals

Providing and fixing 25 mm thick marble partitions for different type of urinals. (HSR 30.40) (II) LARGE SIZE 835 mm x 355 mm (i) white

Providing and fixing in position best Indian make Lavatory suites (with full anti splash rim in vitreous chinaware and all other necessary fittings as fully described in item No.30.41 above. White {HSR 30.42(ii)} ii.) Size 530mm x 430mm with one No. tap

Providing and fixing in position best Indian make chromium plated brass bottle trap 32 mm diameter {HSR 30.50}

Providing and fixing in position best Indian make coat and hat hooks fixed into wall with C.P brass screws and rawl plugs etc. complete including cutting and making good the walls etc. {HSR 30.73(a)(ii)} (a) C.P. BRASS (ii) two way

Providing and fixing in position 15 mm i/d C.P brass bib cocks of best quality ( as required by the Engineer-in-charge) {HSR 30.75(c)} (c) Bib cock

Providing and fixing in position C.P brass stop cock (as approved by the Engineer-in-charge) {HSR 30.76(a)(ii)} (a) 15 MM STOP COCK (ii) concealed stop cock with flange

Providing and fixing in position best Indian make C.P brass inlet connection 15mm with 375mm pipe and C.P brass nuts. {HSR 30.83}

Cutting chase in brick walls in cement or in floor for embedding G.I. or H.C.I. pipe lines and making good the same to its original condition {HSR 30.95(a) (a)size 75 mm X 75 mm

Supply of GI pipe 'B' Class ISI Marked Ravindra/Jindal/Parkash(Surya) Make. (NS) (a)15 mm i/d

(b)20 mm i/d

(c)25 mm i/d

Supply of GI Union Couplings of UNIK/UNCO make . (NS) (a)20 mm i/d

(b) 25 mm i/d

Supply of Gun Metal Peet Valve ISI Marked of DRP/Leader/Bajaj make (NS) (a) 25 mm i/d

(b) 25 mm i/d

Providing and fixing in position PVC flushing cistern 8.0 ltrs. capacity of Hindware/Perryware/Cera make ISI marked, white, alongwith fittings complete in all respect. (NS)

Providing and fixing CP brass jet along with flexible pipe 15mm i/d and patti etc. of best quality complete in all respects (excluding cost of CP brass concealed stop cock).(NS)

Supply and fixing of PVC floor traps of 75 mm i/dia outlet of Prince /Supreme/Skipper make, complete in all respect. (NS)

Supply and fixing of PVC gully traps of 110 mm dia size ( 4") with cover and frame of Prince/Supreme/skipper make complete in all respect. (NS)

Providing and fixing 15 mm to 18 mm thick Z-Black granite stone (polished) in flooring laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade including rubbing and polishing, complete. (NS)

Supply of PVC pipe 6 kg/cm² pressure of ISI marked of Prince / Supreme/Skipper make. (NS) a) 90 mm dia (3” i/dia) size

b) 110 mm dia (3” i/dia) size

Supply of PVC specials of Prince / Supreme/Skipper make as per detail given below:- (NS) (a) PVC elbows 90 mm o/dia

(b) PVC door Tee 90 mm o/dia

(c )PVC cowl 90 mm o/dia

Supply of PVC specials of Prince / Supreme/Skipper make as per detail given below:- (NS) (a) PVC elbows 110 mm o/dia (4")

(b) PVC door junction 110 mm o/dia

(c )PVC cowl 110 mm o/dia

Supply and fixing of PVC flexible waste pipe 40 mm i/dia approximate 3' long along with PVC coupler of best quality, complet in all respect. (NS)

Providing and fixing looking mirror of 4'-0" x 2'-6" size, 5 mm thick mounted on asbestos sheet ground fixied in position by means of 4 No. CP brass screws and washers on rubber washers and rawl plugs embaded in wall or CP brass clamps with CP brass screws etc. complete in all respect. make -Saint Gobain/ Modi/Atul (NS)

Providing and fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colour, shades except burgundy, bottle green, black of any size of approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement coarse sand mortar 1:3 and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete (NS) (b) size of ceramic glazed tiles 600 mm x 1200 mm (i) first floor

Suraj Bhan Contractor