PROVN OF SEVEN TOILET BLOCKS AT VARIOUS LOCATION AT KALIMPONG UNDER GE 867 EWS

Amount

Surface dressing n exc 15 cm deep and getting out in soft/loose soil all as specified and as directed (Including Site Clearance) all as specified and directed.

Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 mtr in depth; for foundation etc. and getting out in Soft/ loose soil all as specified and directed.

Excavating over areas, n exc 1.5 m deep and getting out in Soft/ loose soil all as specified and directed.

Excavating over areas, exc 1.5 mtr but not exc 3.00 mtr in depth; for foundation etc. and getting out in hard/ dense soil all as specified and directed.

M & L PCC 1:4:8 type D-2 (Using 40 mm grade aggregate) in foundation, filling and mass concrete all as specified and directed.

M & L precast cement concrete type C-1 , 1:3:6 (using 20mm graded stone aggt) block masonry with solid blocks exc 10cm in width and setting in CM 1:6 Complete all as specified and directed.

M & L providing precast cement concrete type C-1, 1:3:6, using 20mm graded stone aggregates, solid block building blocks, 10cm thick, set in CM (1:4) complete all as specified and as directed

M & L Earth filling under floors or in foundations(Except Earth) including watering and consolidation spread, levelled all as specified and directed. Note- Earth recive from Excavtion in trench

M & L hard core of gauge n. exc 63mm, deposited, spread and levelled in layers n. exc 15cm thick watered and rammed to a true surfaces in broken stone or boulders all as specified and directed..

M & L 75 mm thick Cement concrete type D-2, (1:3:6, 40mm graded aggregate) as in subbase all as specified and directed.

M&L 75 mm thick PCC (1:3:6 )Type C2 (using 40mm stone aggregate) in plith protection laid in alternative bays finished even and smooth without using extra cement including making 6 mm wide grooves to full depth at 2m to 3m interval and at every change of direction and filling the grooves with mixture of bitumen and sand mixed in the ratio of 1:3 by weight complete all as specified and directed by Engineer-In-Charge.

M & L for PCC (1:3:6)type C-1 (using 20mm graded aggregate) as in surface channels,drains including all necessary form work complete all as specified and directed.

M & L extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, moulds mitred / stopeed endes etc

M & L Damp proof course 40 mm thick in cement concrete (1:2:4) Type B-0 to horizontal or vertical surfaces including necessary formwork all as specified and directed.

M & L Reinforced cement concrete M-25 (design mix) as in plinth Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. Note: Formwork and reinforcement shall be measured and paid separately.

Form work to sides and soffits of floor or roof beam, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc also splays between floors and beams,etc all as specified and directed.

M & L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

M & L TMT bars 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified conforming to Fe-500D all as specified and directed.

M & L TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

S&F for structural steel work as in roof trusses (framed), trussed, purlins, framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc all as specified and directed.

S&F for pre- painted galvatume aluminum zinc coating (AZ-70) GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed

S&F for Pre painted galvalume aluminium zinc coating (AZ-70) GI based Plain steel sheet 0.50mm thick of an colour having tensile strength of 550mpa as in roof covering eaves board, gutter, valley and in cladding to wall fixed with self tapping screws all as specified and directed by Engr-in-Charge.

M & L Non - skid Ceramic tiles 7 to 8 mm thick premium quality conforming to relevant IS ( Suare/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed or bedding layer in CM (1:6) Complete all as specified and directed.

M&L 350X250 mm X7mm thick / 300X450X7mm/450X350X7 mm thick coloured glazed ceramic tiles fixed as in vertical surface such as risers of steps, skirting, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile over and including 10 mm thick backing plaster in CM ( 1:4) finished even and rough complete all as specified and directed.

M & L Plain concrete Type (1:2:4) mix type B1(using 20mm graded stone aggregate) as in Copings, kneelers, apex stones, bed plates,water trough and like including weathering, slightly rounded or chamfered angles and throating including necessary form work complete all as Specified and directed.

M&L rendering 15 mm thick in CM (1:6) on fair faces of brick work or concrete surfaces to be finished even and smooth with out using extra cement mixed all as specified and as directed.

M&L rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surfaces to be finished fair and even without using extra cement mixed with intergral water proofing compound @ 3% by weight of cement (WPC measured and paid separately) all as specified and as directed.

Supply only integral water proofing compound (Make : Squant/CTCO) all as specified and as directed.

M&L for preparation on newly plastered/previously untreated surfaces of wall and applying two coats of exterior emulsion paint (apex) over a coat of primer of alkali-resistant complete all as specified and directed.

M&L for three coats of white wash on new plastered surface including prepration of wall surface

M & L for preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide all as specified and directed.

Returning filling in , including, spreading, levelling, watering and well ramming in layers not exc 25cm in soft / loose soil all as specified and directed.

Removing excavated material n. exc 50m and depositing where directed at a level n. exc 1.5m above the starting point in soils all as specified and directed..

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing all as specified and directed.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail , lock rail and bottom rail on either side and as gap insert for top rail and bottom rail , panelling of plain colour PVC sheet to be fitted in the MS framewelded/ sealed to the stiles and rails with suitable PVC sheet beading , and jointed together with solvent cement in the frame at site as per specification all as specified and directed.

S & F 100 mm size butt hinges,medium weight,stainless steel all as specified and directed.

S & F 200 mm Aluminium anodised,barrel tower bolts of extruded section and fixed all as specified and directed.

S & F 150mm long aluminium handle cost type anodised all as specified and directed.

S & F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S & F 4 mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S & F Soap dish, any type, fixed to plugs with chromium plated brass screws all as specified and directed.

S & F Vitreous China wash basin, angle back, size 600x480mm white, excluding taps, waste, chain and plug and porcelain stopper but including brackets, cutting for & plinning in ends of brackets or erecting stands all as specified and directed..

S&F vitreous china wash down water closet pan (Pedestal pattern) white (excluding fixing bolts,seat cover, flushing cistern and flush pipe) including for fixing 'P' or 'S' trap and also inclusive of connecting to union of flushing cistern and drain pipe complete all as specified and directed.

S&F plastic water closet seat cover, of approved colour, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S & F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) Water closet (Squatt pattern) com plete including provision of lime concrete bedding all as specified and directed.

S&F PVC (SWR) "P" trap 110 mm bore complete all as specified and directed.

S & F bib taps 15mm bore cast copper alloy chromium plated with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule & fixed 15mm bore all as specified and directed.

S & F Grating doom 100mm dia of PTMT (Minimum weight 25gms) all as specified and directed.

S&F PVC (SWR) gully trap 110 mm bore, setting jointing with solvant cement all as specified and directed.

S&F 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement all as specified and directed.

S & F Pillar taps 15mm bore, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed all as specified and directed.

S & F PVC valve less , syphonic action type flushing cistern 10 ltr capacity low level, whit, with inlet, ball valve float, flush pipe and handle including brackets, low level fluslhing cistern (exclusive of brackets), and connections to pipes and fixing of chain and pull, or lever, if any all as specified and directed.

S & F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe)Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) all as specified and directed.

S&F Urinal spreader of Chromium plated (CP) for fixing with 15 mm dia pipe. (Minimum weight 60gms all as specified and directed.

S & F Stop cock 15 mm bore cast copper alloy screwed down high pressure fancy type, chromium plated with long shank and cup (concealed type) all as specified and directed.

Cutting chases, pinning in brick/pcc block wall and making good to facings where equired and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring all as specified and directed. etc., and making good, cutting not exc 10 cm girth

S & F 15mm bore GI tubes medium grade galvanized with and incl all GI fitting(Such as bends,elbows,Tees,connectors,short pieces,back nuts,unions, caps and plug etc)and fixed complete to wall ceiling or laid in/on floor complete all as specified and directed.

S&F CP towel Rail 20mm dia, D type, 60cm long between flanges etc, complete all as specified.

S&F Brass chromium plated shower rose with or without swivel joints 125 mm size , including fixing to steel pipe or unioncomplete all as specified and directed.

M &L PVC connections 15mm size with PTMT nuts of length 300mm all as specified and directed.

S & F PVC (SWR) pipe 75mm bore single socketed in any length with rubber ring joint fixed to wall (ISI Marked) all as specified and as directed.

S & F PVC (SWR) pipe 110mm bore single socketed in any length with rubber ring joint laid in trenches or in floor (ISI Marked ) all as specified and directed.

S&F PVC ( SWR ) bends 75 mm bore all as specified and directed.

S&F PVC ( SWR ) bends 110 mm bore all as specified and directed.

S&F PVC (SWR) branch pieces 75 mm (Single Y) equal or unequal all as specified and directed.

S&F PVC (SWR) branch pieces 110 mm (Single Y) equal or unequal all as specified and directed.

M&L for RCC M-25(design mix) slabs supported on walls, beams and columns in floors, roofs, landing, balconies, canopies, deck slabs and in shelves and the like all as specified and directed.

M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail?ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizon?tal or sloping and similar work exc 10cm but n exc 20cm wide all as specified and directed.

M & L Formwork to suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surfaces flat, complete all as specified.

S & F 75 mm bore PVC (SWR) waste and vent pipes in any length fixed to walls complete all as specified and direted.

S & F 75mm bore PVC (SWR) cowl complete all as specified and directed.

M&L for rendering 15 mm thick other than fair faces of brick work or concrete surfaces in cement mortar (1:4) finished even and fair all as specified and directed.

M & L Brickwork with subclass ‘B’ bricks, in one brick thick honey comb walling built in Cm 1:4 all as specified and directed.

M & L Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius in Cm 1:6 all as specified and directed.

M & L Providing precast ce- ment concrete Type B1 1:2:4 in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces all as specified and directed.

S & F PVC (SWR) vent pipe 110 bore fixed to walls all as specified and directed.

S & F PVC (SWR) vent cowl 110 bore all as specified and directed.

M & L Loose filling with broken brick aggregates of gauge 80 to 150 mm in soakage pits, soakage wells all as specified and directed.

M &L for 100 mm thick PCC 1:4:8 type D-2 (Using 40 mm grade aggregate) as in floor finsh even and smooth without using extra cement all as specified and directed.

M & L for PCC 1:3:6 type C-2 as in Concrete bed to drain pipes 110 mm dia including packing under, and haunching against the sides of pipes after they are laid and tested; in all as specified and directed.

M&L rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surfaces to be finished even and smooth using extra cement complete all as specified and as directed.

Material and labour for point wiring with 1.5 Sqmm (nominal area) PVC insulated un - sheathed single core multi stranded copper conductor FRLS cable 1100 volts grade (conforming to IS) drawn through and including rigid non metallic PVC conduit not less than 20mm size, medium grade with all necessary fittings, concealed wiring , for light / E/fan/Bell point controlled by one switch including 1.5 Sq mm PVC insulated copper stranded conductor for earth continuity conductor and connected to earth dolly and to be terminated in 1.6 mm thick pressed steel terminal boxes (concealed type in permanent bldg and surface in temporary bldg or as directed ) for mounting fittings like switch, socket, fan regulator etc. with 3 mm thick laminated bakelite sheet cover ,for housing switches, socket outlet, regulator etc. complete all as specified or directed including testing on completion all as specified and directed.

All as per item No 1 here – in – before but for one 3 / 5 -pin switch socket outlet 5 amps on independent board all as specified and directed.

All as per item No 1 here-in-before but One 3 pin socket outlet 5 Amps on the same board with other switchs with cables 1.5 Sqmm size.

Supply and fix switch piano flush button, single pole, 5 amps, one way all as specified and as directed.

Supply & Fixing ceiling rose surface bakelite 65 X 50 mm three terminal all as specified and as directed.

Supply and fix switch socket combination 2 – in – one, 3 Pin / 5 Pin, 5 amps flush type all as specified and as directed.

S & F Energy efficient LED tube light fitting 4", 1x18 watt, with bipin holders, connector block, CCT - 6500K, system output lumen not less than 2000lm, extruded aluminium housing with high quality Polycabonate diffuser, wide voltage protection range 140V-270V including connecting up with PVC insulated 3 core sheathed 0.5 sqmm copper conductor two numbers PVC mounting blocks for fixing of fitting complete all as specified and as directed by Engineer-in-charge. Make : Philips, Model - TMC 501, TMC 501P 1XT-LED 22W P3241 MAS LED tube 18w 1800 lm 865 T8 or equivalent in Crompton/Havells.

Supply and fixing lamp holder insulated body with back plate for batten fitting all as specified and as directed.

S & F in LED retro fit lamp B-22 holder base with poly carbonate body and aluminium heat shrink of 5 W complete with tube rod all as directed.

Supply and fixing Sheet metal enclouser Double door for MCB DB,s Phosphatised Powder Painted with bus bar 200 Amps rated Single pole and neutral linkof 4 way 240 Volts AC. Make- Legrand/Siemens/Schindler all as specified and directed.

Supply and fixing MCB Single pole and neutral upto 32 Amps capacity 10 KA 240 Volts 50 HZ. conforming to IS/IEC 60898-1 2002, integrated label holder, Sliding bottom clamp, IP 20 protection, Cat part no 4086 17 of Legrand or equivalent in Siemens/Schindler all as specified and directed.

Supply and fix MCB/Isolator single pole (SP), 10 kA of 6 Amps to 32 Amps capacity 240 Volts. conforming to IS/IEC 60898-1 2002, integrated label holder, Sliding bottom clamp, IP 20 protection, Cat part no 4085 87,90,92,93,94,95 of Legrand or equivalent in Siemens/Schinder all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified and directed.

Supply and laying testing steel water tubing medium grade with all fitting fixed to wall/ceiling or laid in floor of size 25 mm bore all as specified and directed.. Make : TATA/Jindal/Bansal.

Supply and laying and testing steel water tubing medium grade with all fitting laid in fixed to wall/ceiling or floor of size 20 mm bore. Make : TATA/Jindal/Bansal.

Supply and fixing Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position with all fitting such as tank nipple and locking arrangement all as specified in SSR Part-I of capacity 500 ltr including S&F brass valves with polythene float and fly nut complete scerwed for iron pipe of brass ferrule and fixed of size 25 mm all as specified and directed.

Supply and fixing gun metal globe valve iron wheel screwed both end for iron pipe fixed all directed of size 20 mm all as specified and directed.. Make : Zoloto or ISI marked.

Supply and fixing gun metal globe valve iron wheel screwed both end for iron pipe fixed all directed of size 25 mm all as specified and directed.. Make : Zoloto or ISI marked.

M&L compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc conforming to Fe 410-w (Fde - E- 250) Quality A & painting with two coat of black bitiminious paint over a coat of Red Oxide primer complete all as specified by Engr-in-Charge.

M&L PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in coping including weathering, slightly rounded or chamfered angles and throating, as directed and necessary form work complete all as specified and directed.

M&L 15 mm thick rendering in cement mortar 1:4 on fair faces of brick or concrete surfaces, rendering finished even and smooth (without using extra cement complete all as directed.

M&L for sand cushioning to U/G cable in layers of 23cm thick( 8 Cm before laying the cable and 15Cm thick after laying the cable) in trenches complete all as specified and directed. Note :- Only Puned layers shall be measured.

Supply and laying reinforced precast concrete cable cover, class LV, type 1, flat, size 250mmx150mmx40mm complete all as specified and directed..

Supply and Laying u/g cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor on wall with the help of shadel of size 10 Sqmm 2 core as required at site all as specified and directed..

M & L GI tube light grade for passing through cables under the floor ,along the wall or along the pole of 25 mm bore and fixed to the poles/walls with suitable size of MS clamps and nut and botls/washers complete all as specified and directed.

S & F GI frame work of size 605 X 605 mm for seamless ceiling comprising of GI perimeter chanel 0.55mm thick with two unequal flanges of 20 and 30 mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm center to center/intermediate channel 0.9mm thick having two equal flanges of 15 mm each and web of 45mm suspended from soffit at approx 900mm center to center with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length)of .55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting channel at 457 mm center to center complete all as specified and as directed.

S & F PVC false ceiling with light weight PVC hollow section panel made of 1mm thick and over all thickness of panel 7mm thick and 200mm wide strip of colour teak wood grain/melamine finish,fixed in new false ceiling grid made of Aluminium/G.I /M.S/wooden complete all as specified and directed. Make-Sintex,Duraplast,Polyline Pvt Ltd and Kingston Note-New false ceiling grid of aluminium/GI/MS/wooden shall be measured and paid separately

M & L for coloured & polished Chequred cement concrete tiles 30cm X 30cm X25mm thick set jointed and pointed in neat cement slurry as in floors including 20mm thick screed bed with CM(1:6) all as specified and directed.

PRASAD PRADHAN AND SON

G K SUTHAR

DEEP CHANDRA JOSHI

GEETA CONSTRUCTION

S K ENTERPRISES

SANJAY SAW MILL

JAYSHREE CONCERN