SPECIAL REPAIR TO LAUNDRY AND E/M INSTALLATION IN QM BASEMENT AREA OF CH(EC) UNDER GE (A) KOLKATA

Amount

NOTES :(i)The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates. (ii) It is highlighted that the cretin condition of General Condition Of Contracts (IAFW-2249) has been modified as direction of MOD i.e inclusion of performance security, deletion of risk & cost provisions and increase in defects liability period all as specified in tender document. The tenderers should keep in mind while quoting their offer

Demolition of brickwork or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars,etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Demolition of reinforced Concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition)

M&L for brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed (upto 4 storey)

M&L for brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick walling built in cement mortar 1:4 complete all as specified and directed

Chipping of unsound /weak concrete materials including cover plaster from RCC structural member i.e. beams, columns,Slab,chajja,fins etc. 50 mm average thickness including tapering all edges, making square shoulders of cavities air and cleaning of exposed concrete surface of lightly picking materials by manual method including foreign materials , loose concrete/aggregate etc and disposal of all debris out side of MOD land and complete all as specified and directed.

Removing of concrete all around reinforcement bar upto 12 mm dia and over from behind the reinforcing bars average 25mm (but not less than 15mm air gap)by manual methods (using wire brushing ,chiselling etc) and applying chloride free rust removing chemical on rusting steel reinforcement bar and removing all rust from steel reinforcement bar by emery paper and cleaning the area throughly by water and allow it to dry and totally rust free of reinforcement bar all as complete as per manufacturer's instruction as specified and as directed. Make (Rust removing chemical):- Reebaklens RR of FOSROC or equivalent product of SIKA/STP / Hindcon Chemical Pvt Ltd as approved by GE.

Material and labour for preparing existing reinforcement surface by brush and application of two component epoxy zincrich primer on existing reinforcement surface incl necessary scaffolding (epoxy primer shall have a minimum specific gravity 1.75, adhesive bond strength with steel is 1.50N/mm2 and maximum coverage area 5.00 Sqm per litre) complete all as specified and directed. Make- Nitozinc primer of FOSROC or equivalent product of SIKA/STP / Hindcon Chemical Pvt Ltd

Material and labour for introducing new reinforcement bars upto 12 mm dia and over for structural connection in RCC beams, columns, lintel and slabs including power drilling holes of appropriate diameters in reinforced or plain cement concrete to a minimum depth of 150mm and upto 200mm including power drilling,fixing the reinforcement in position using epoxy, cleaning of loose dust by blowing air, sealing with epoxy cartridges etc including necessary scaffolding complete all as specified and directed

Material and labour for providing and placing in position free flow shrinkage cementitious micro concrete of grade of M-50 to the effected beam, columns, slab, chajja etc. The micor concrete shall have a minimum 1 day compressive strength of 10 Mpa and 28 days strength of 50 MPa, minimum tensile strength 5N/mm2 at 28 days, minium flexural strength of 5 MPa at 28 days for strengthening of beams, columns & other structural elements of average thickness 50mm and including surface preparation & suitable type formwork etc. as per manufacturers instruction complete all as specified and as directed.Make (micro concrete):-Renderoc RG of FOSROC or equivalent product of SIKA/STP / Hindcon Chemical Pvt Ltd

Material & labour application of two component structural grade polymer modified reinstatement mortar of compressive strength, flexural strength shall not be less than 45 MPa at 28 days , 7MPa at 28 days respectively (Maximum coverage area 1.3 sqm per 25 kg pack @ 10 mm thickness) over a coat of epoxy Bonding agent on existing surface for strengthening of beams, columns & other structural elements of average thickness 25mm and morter shall be applied in layers n.exc 6mm thick in layers and including surface preparation as per manufacturers instruction complete all as specified and as directed. Note:- This item shall be executed where shuttering is not possible or small patch repairs of structural elements .Make (polymer modified reinstatement mortar):- Renderoc S2 of FOSROC or equivalent product of SIKA/STP / Hindcon Chemical Pvt Ltd

Material and labour for applying of high efficiency polymeric resin base film forming curing agent/compound over concrete surface and maximum coverage area 5.00 Sqm per litre as per manufacturers instruction complete all as specified and as directed. INCL necessary scaffolding) Make:- Concure LP90 of FOSROC or equivalent product of M/s Choksey chemical Pvt Ltd / M/s STP Ltd / M/s Thermax Ltd

Dismantling of existing Expansion joint system and M & L applying TPO/FPO based joints sealing membrane, Sikadur Combiflex SG (150x2mm) with epoxy adhesive, Sikadur 31 C ( the joint shall be packed withing polystyrene board before application of Combiflex ). Then providing Sika pllystrene sealant into the gap after proper surface prepration after filling the gap with polyurethene backer rod, followed by precast RCC slab (1:2:4 ) 50 mm thick placed over the joint with minimum 150 mm projection on either side with proper drip course of size (length) n.exc. 1.2 mtr each and sealing the joints of precast RCC slab with exterior grade silicone sealant of size i.e. 10 mmx 10 mm balance with polystrene board complete all as specified and as directed by the Engr -in-Charge.

M&L for TMT Mild steel bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directe

All as per item No 14 here-in-before but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed

M&L for Formwork to sides of pillars,posts, struts, piers, columns and stanchions for rough finished surfaces of concrete sqaure or rectangular complete all as specified and directed

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers,lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed

M&L for Formwork rough finished surfaces of concrete flat to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed

M&L for Reinforced cement concrete M-25 (design mix) using 20mm graded stone aggregate as in Columns, pillars, piers, posts and struts complete all as specified and directed

M&L for Reinforced cement concrete M-25 (design mix) using 20mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed

M&L for Reinforced cement concrete M-25 (design mix) using 20mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed

Taking down cement plaster on brick or stone wall surfaces including glazed tiles wherever exists including raking out joints, hacking for key and scrubbing down with water complete all as specified and as directed.

M&L for 5mm thick plastering on ceiling surfaces in CM (1:3) surface finished even and fair complete all as specified and directed.

M&L for 20mm thick (in two layer) plastering on fair face of Brick surface with CM (1:4) mixed with WPC finish surface even and smooth with out using extra cement complete all as specified and directed.

M&L for 15 mm thick cement plaster with CM (1:6) on other than fair face of brick wall finsh even and smooth without using extra cement complete all as directed.

Supply only Intregal water proofing compound

Taking down chowkhats or frame with shutter (without taking off shutters from the frame) exc 1.5 sqm n.exe 4 sqm each complete all as specified and directed.

Taking down old rusted steel windows/ventilators of any description and size with or without shutters complete all as specified and as directed

S & F 2nd H/W plain solid straight chowkhats,wrought framed rebated on the solid,rounded or chamfered put together with glue pinned at joints complete all as specified and directed

M&L for 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with both face covered with decorative face veneer with lipping/frame to match complete all as specified and directed

S&F for Factory made single extruded WPC(Wood polymer composite) solid door Frames of size 45 x 70mm comprising of virgin PVC polymer of K value 58-60(Suspension grade), calcium carbonate & natural fibres and non-toxic additives fabricated with mitre joints after applying PVC solvent cement and screwd with full body threaded star headed SS screws having minimum frame density of 750 Kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), mimimum compressive strength of 58 N/Sqmm and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof & fire retardant & fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed

S & F S&F for Factory made single extruded WPC(Wood polymer composite) solid flush door shutter of 30mm size comprising of virgin PVC polymer of K value 58-60(Suspension grade), calcium carbonate & natural fibres and non-toxic additives fabricated with mitre joints after applying PVC solvent cement and screwd with full body threaded star headed SS screws having minimum density of 650 Kg/cum, screw withdrawal strength of 1800 N(Face) & 900 N (Edge), mimimum compressive strength of 50 N/Sqmm, modulas of elasticity 850 N/sqmm & resistance to spread of flame of class A category with property of termite/borer proof , water/moisture proof & fire retardant & fixing with SS butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per dirns of EIC.

S&F Anodised powder coated aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators etc with one or more rebates including joining cleat for fixing etc complete all as specified and directed

S&F for Anodised aluminium powder coated door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

S&F Anodised powder coated aluminium (minimum thickness of powder coating 50 micron) window and ventilator shutters, sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified and directed

S&F 12 mm thick prelaminated particle boards (ISI marked), interior grade prelaminated both side with decorative choice lamination, fixed with necessary clips and other like to aluminium frame work, as in doors, partition etc complete all as specified and as directed.

S&F 4.8 mm thick Sheet glass, ordinary quality and glazing in square n exc 0.5 sq. m in each pane fixed to aluminium frame work complete all as specified & as directed.

S&F 4.8 mm thick Sheet glass, ordinary quality and glazing in square exc 0.5 sq. m in each pane fixed to aluminium frame work complete all as specified & as directed.

S&F 5.5 mm thick glass ordinary quality, frosted on one side fixed to aluminium frame work exc 0.5 Sq. m in each pane complete all as specified & as directed.

S&F aluminium 4 levers Mortice lock, vertical type, size 100 mm complete all as specified and directed

S&F Extruded aluminium alloy handles 75mm long, fabricated type,anodised complete all as specified and directed

S&F Extruded aluminium alloy handles 150mm long, fabricated type,anodised complete all as specified and directed

S&F 300mm long sliding door bolts with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bots and sliding bolts of extruded or cast aluminium alloy complete all as specified and directed

S&F Aluminium anodised barrel tower bolts of extruded section with 200 mm long bolt, complete all as specified and directed.

S&FAluminium anodised barrel tower bolts of extruded section with 150 mm long bolt, complete all as specified and directed .

S&F Bearing hinges 100mm, cast brass, with Stainless steel hinge pin, bright polished and fixed, typeB-11 complete all as specified and directed

S&F for Stainless steel wire cloth having 0.36 mm nominal dia of wire and average width of appreature 1.40 mm and fixed with stainless wire staplescomplete all as specified and directed

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required hooks (stay), heavy, for large gates; hook and pintle hinges large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed

M&L for cement concrete type B0 (1:2:4) 12.5 mm graded aggregate as in hold fast block kerbs or mud stops, rounded or chamfered etc comlete all as specified and directed.

S&F door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and directed

S&F floor door stopper overall length of cover plate 150mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed

Dismantling of stone slabs and tiles of any description or thickness in floors,aprons etc laid, bedded & pointed in any mortar complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed

M&L for machine cut kota stone slab flooring 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

M&L for Kota stone slab 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement, screed and jointed complete all as specified and directed

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed

M&L non-skid joint free ceramic (coloured) tiles 7-8mm thick area of each tiles exeeding 0.06sqm but n.exceeding 0.11 sqm in toilet/bath floor etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified & as directed. Note: Screed bed shall be measured and paid separately

M & L for non skid (coloured) ceramic tiles, 7 to 8 mm thick (square/rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floor etc, of superior quality, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed. Note: Screed bed shall be measured and paid separately

M&L for glazed ceramic (coloured) tiles of size 300x600 6-7mm thick as in vertical surface/dado set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed

M&L for screed bed or bedding layer of mortar 20 mm thick in CM 1:4 for laying floor finishes complete all as specified and directed

M&L for screed bed or bedding layer of mortar 15 mm thick in CM 1:6 for laying floor finishes complete all as specified and directed

M&L for bedding layer of mortar 15 mm thick in CM 1:3 for laying wall/dado finishes complete all as specified and directed

M&L for bedding layer of mortar 10 mm thick in CM 1:4 for laying wall/dado finishes complete all as specified and directed

Demolition of cement concrete above ground floor n.exe 15cm thickness(below or above ground level) complete all as specified and directed.

M&L for 100 mm thick PCC (1:2:4) type B1 (20 mm graded stone agg) as in flooring, finished even and smooth with using extra cement complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing etc., and making good, cutting not exc 10 cm girth complete all as specified and directed

Taking up or down 15mm bore steel water tubing and connections and removing all as directed

Taking up or down 20mm bore steel water tubing and connections and removing all as directed

Taking up or down 25mm bore steel water tubing and connections and removing all as directed

Taking up or down 40mm bore steel water tubing and connections and removing all as directed

S&F galvanised 15mm bore steel water tubing (GI pipe), medium grade with all fittings and fixed to wall, floor and ceiling of following bore complete all as specified and as directed.

S&F galvanised 20mm bore steel water tubing (GI pipe), medium grade with all fittings and fixed to wall, floor and ceiling complete all as specified and as directed.

S&F galvanised 40 mm bore steel water tubing (GI pipe), medium grade with all fittings and fixed to wall, floor and ceiling complete all as specified and as directed.

S&F galvanised 25mm bore steel water tubing (GI pipe), medium grade with all fittings and fixed to wall, floor and ceiling complete all as specified and as directed :-

S&F 20 mm bore (Outer dia) CPVC pipes of SDR 11and plain CPVC SDR 11 fitting fixed on wall or floor (concealed ), ceiling or laying in floors complete all as directed.

S&F in 25 mm bore (Outer dia) CPVC pipes of SDR 13.5 and plain CPVC SDR 11 fitting fitting fixed on wall or floor, ceiling or laying in floors complete all as directed.

S&F 20 mm bore CPVC Male Brass Threaded Adaptor (MTA/ MBTA)

S&F 25 mm bore CPVC Male Brass Threaded Adaptor (MTA/ MBTA)

S&F 20mm bore CPVC Female Brass Threaded Adaptor (FTA/ FBTA)

S&F 25mm bore CPVC Female Brass Threaded Adaptor (FTA/ FBTA)

S&F 50 mm bore CPVC Male Brass Threaded Adaptor (MTA/ MBTA)

S&F 50 mm bore CPVC Female Brass Threaded Adaptor (FTA/ FBTA)

S&F 50 mm bore (Outer dia) UPVC pipes of SCH-40 and plain UPVC SDR 11 fitting fixed on wall or floor, ceiling or laying in floors complete all as directed.

S&F in repairs vitreous china squatting pan of “Orissa” pattern of size 580 mmx 440mm white with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floor complete all as specified and as directed.

S&F in repairs vitreous China wash down water closet pan ( padestal pattern) incl PVC seat cover , (excluding fixing bolts, flushing cistern and flush pipe) , including connection to drain ( or outgoing pipe) and to flushing pipe , etc., complete complete all as specified & directed.

S&F in repairs vitreous china wash hand basin, white, flat back, size 550mm x 400mm, exc chain and plug and porcelain stopper but including cutting for and pinning in ends of and including brackets, waste pipe & CP brass waste coupling of 32mm dia complete all as specified and directed.

S&F in repairs Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified & directed.

S&F in repairs 15mm bore CP angular valve fancy type,with crutch handle, screwed for iron pipe or for brass ferrule and fixed of following size complete all as specified and directed

S & F in repairs 15 mm Dia CP Bib taps,fancy type with crutch handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified & directed.

S & F in repairs 15 mm Dia CP stop cock(concealed type), with crutch handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified & directed.

S&F in repairs 15 mm bore CP pillar taps, with capstan heads, chromium plated, Fancy type screwed down for pipe, high pressure ,complete all as specified and directed.

S & F in repairs 25 mm Dia brass gun metal gate valve , with crutch handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified & directed. .

S&F in repair CP Health faucet with all necessary fittings complete all as specified & directed. . Make : Prayag/Cera/Jaquar or equivalent Make : Prayag/Cera/Jaquar or equivalent.

S&F in repair 600 mm PVC connection pipe 15 mm size with PTMT nut of following length complete all as specified and directed .

S & F in repair 110/125 mm floor trap fixed in floor with grating incl jointing with solvent 1:2:4 cement concrete,complete all as spd and directed

S&F in repair PVC valveless, symphonic action type low level flushing cistern white with inlet ball valve, float and handle including brackets, 10 ltr capacity complete with flush pipe(Long bend) 32mm dia of make as approved by GE complete all as specified & directed.

Dismantling of 100mm cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls

S&F 110mm dia PVC (SWR) pipes double socketed in any length with rubber ring joints fixed to walls

S&F PVC (SWR) bends 110mm dia

S&F PVC (SWR) junction single, (Single T) equal or unequal

S&F PVC (SWR) junction double, (Single T) equal or unequal

Dismantling of old unserviceable water tank, removing from site, Supply and fixing of rotational moulded polythene water storage tank 2000 litre capacity ISI marked (cylindrical, vertical, double layered with closed top) hoisted and fixed in position including PVC float valve 20mm bore weight not less than 210gms. Complete.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets.

M&L for Perforated 12mm thick particle board/ tiles for insulation and accoustic purposes, 60x60 cm in size, fixed with screws to timber framework or with staples on snap grid as in wall complete all as specified & directed.

M&L for Perforated 12mm thick particle board/ tiles for insulation and accoustic purposes, 60x60 cm in size, fixed with screws to timber framework or with staples on snap grid as in ceiling fixed in ceiling, flat or sloping complete all as specified & directed.

Fixing only Perforated 12mm thick particle board/ tiles for insulation and accoustic purposes, 60x60 cm in size, fixed with screws to timber framework or with staples on snap grid as in wall. Note :- Serviceable boards obtained from item No 105 above

M&L for Anodised aluminium snap grid frame work for false ceiling in ceiling flat or sloping with Hangers 6 mm dia. G.I. (upto1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long with 4 mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws complete all as specified and as directed.

Taking down old rusted u/s steel collapsible gates or rolling shutters any size including taking out holdfasts/anchorages and other fixtures complete all as specified

S & F in repair collapsible steel gates, top hung consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with hold fasts and brackets, complete all as specified & directed.

S&F in Repair 1.25 mm steel rolling shutters without ball bearing,as specified including top cover,anchoring,hasp and staple and one shop coat of primer erected in position as indicated,complte: but gear operated type with chain wheel and hand chain complete all as specified & directed..

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified & directed.

S&F Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel' complete all as specified & directed.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment.Fe 290(Gde-165) complete all as specified & directed.

S&F mild steel rolled section for Stairs (framed) including stringers, treades, landing, balusters, hand rails etc. in including cleats, brackets, etc.complete Fe 290(Gde-165) complete all as specified & directed.

S&F Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars stiffeners, gusset plates, etc.Fe 290(Gde-165)complete all as specified & directed.

S&F in repair Mild steel 1.25mm, plain, black sheet in wall cladding,steel gates and similar work, cut to size, holes punched; including round headed screws clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required.

M&L for 3mm thick wall care putty on wall including rubbing with sand paper to achieve a smooth surface & sharp straight edges etc. complete all as specified & as directed.

M&L for preparation of newly plastered wall surface two coats of oil bound distemper over a coat of primer on complete all as specified and directed.

M&L for preparation of newly plastered ceiling surface & applying three coats of white wash complete all as specified and directed.

M&L for preparation of plastered and unplastered surfaces of old decorated walls take a one coat of acrylic oil emulsion distemper complete all as specified and directed.

M&L for preparation of old plastered ceiling surface & applying one coat of white wash complete all as specified and directed.

M&L for preparing surfaces new decorated plastered or unplastered surfaces of wall, pillasters, cornices etc and applying two coat of dirt resistance exterior paint of required shade complete all as specified and as directed.

M&L for preparing of new steel surfaces & applying two coats of synthetic enamelled paint over a coat of red oxide primer complete all as specified and as directed.

M&L for Two coats of synthetic enamelled paint on New wooden surface exc 10cm width or girth including preparation complete all as specified and as directed.

Preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described,treating ends of posts, backs of chowkats, etc., area tarred exc 0.1 sq. m but n exc 0.5 sq. m each complete all as specified and directed.

Taking down copper/ aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceilling roses, pendants , regulators, sockets etc excluding light fitting for taking credit removing from site and making good disturbed surface of walls, floors etc all as specified and directed by Engineer-in-Charge.

Taking down carefully Sub main wiring of size upto 10 Sqmm including making good disturbed surfaces of walls, ceilings etc complete all as specified and directed.

Material & labour for point wiring concealed type in PVC conduit for one light / fan point controlled by one way switch, with 1.5 Sqmm PVC insulated copper cable multistrand conductor 1100 volts grade (Red colour cable used for live connection, Black colour cable used for neutral connectionand green cable used for earthing connection, separate cable for earthing and neutral to be used for each individual circuit from the distribution board / switch board) controlled by one way switch drawn through and including appropriate size of PVC casing capping / conduit with all accessories for surface / concelaed wiring including 1.5 Sqmm PVC insulated, unsheathed, copper cable multistrand conductor 1100 volts grade for continuity earth wire connected to each point and sunk cast pressed steel terminal box made out of MS sheet 1.2mm thick for mounting of fittings like switch, socket and fan regulator with 3mm thick laminated / backalite sheet cover complete all as specified and directed. Make of Copper wire : Polycab / Havells / RR & Make of PVC Conduit : Presto Plast / Finolex / Kalinga

All as per item No 129 here-in-before but for One 3 pin socket outlet, 5 Amp on the same board with other switches with cable 1.5 Sqmm each

All as per item No 129 here-in-before but for One 3 pin, 5 Amps S/Socket Pt on independent board with 1.5 Sqmm cable

All as per item No 129 here-in-before but for one 3 pin socket outlet independent but below the switch board of light points in the same vertical plane, with cables, 1.5 Sqmm size

All as per item No 129 here-in-before but for 5 pin 15 Amps switch socket combination on independent board with 2.5 Sqmm cable

All as per item No 129 here-in-before but for power socket py with 4 Sqmm cable and 2.5 Sqmm earth continuity wire

M & L for socket outlet 2 in 1, 3 pin, 5A, flush type, 240 volts, flush type all as specified and directed Make: Legrand / Anchor / Havells

M & L for switch socket combination 2 in 1, 5Amps, 240 V flush type, universal all as specified and directed Make: Legrand / Anchor / Havells

M & L for switch socket combination 5 Pin, 5 / 15Amps, shuttered flush type, 240 V universal all as specified and directed Make: Legrand / Anchor / Havells

S & F single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with one single pole MCB 240 Volt 20 Amps complete all as specified & directed. Make: Legrand / Anchor / Havells

S&F switch piano type 5 Amp single pole one way complete all as specified & directed. Make: Legrand / Anchor / Havells

S&F Ceiling rose surface backelite 65 x 50mm three terminals complete all as specified and directed. Make: Legrand / Anchor / Havells

S & F stepped type electronic fan regulator, flush type on the existing all as specified and directed. Make: Legrand / Anchor / Havells

Supply & fixing main stream battens fitting LED 20 watt tube light fitting 1 x 4 feer long battens fitting and all accessories, prewired and flexible wire twin core from ceiling rose to terminal block including taken down old unsv and mak good the disturbed surface all as specified and directed. Make: Crompton, cat No CCS-102-10-65-SL-DP-NWH or equivalent in Philips / Havells

S & F MCB SP of rating 6 to 32 Amps, 240 V, of breaking capacity 10KA. ISI Marked, complete all as specified and directed. Make:- Legrand / L&T / Schnieder / C&S / Havells

S & F MCB SPN of rating 40 to 63 Amps 240 V, of breaking capacity 10kA, complete all as specified and directed. Make:- Legrand / L&T / Schnieder / C&S / Havells

S & F MCB Triple pole and neutral 415 Volt and current carrying capacity 63 Amp Make:- Legrand / L&T / Schnieder / C&S / Havells

Taking down MCB DB of any capacity and making good disturbed area complete all as specified and directed by Engineer-in-Charge Make:- Make:- Legrand / L&T / Schnieder / C&S / Havells

Supply and fixing as in repair MCB DB TPN (double door) 4 way 415 volt including bus bar neutral link, earth bar and din rail, recessed with all wall surfaces by chase cutting and making good surfaces of wall as specified and directed by Engineer-in-Charge Make:- Legrand / ABB / Schnieder / C&S / Havells

Supply and fixing as in repair MCB DB SPN (double door) 8 way 240 volt including bus bar neutral link, earth bar and din rail, recessed with all wall surfaces by chase cutting and making good surfaces of wall as specified and directed by Engineer-in-Charge Make:- Legrand / ABB / Schnieder / C&S / Havells

S & F Sheet Metal enclosures for DB's for MCBs Single pole & neutral 4 way 240 volt with out bus bar single door Make:-Make:- Legrand / ABB / Schnieder / C&S / Havells

Material & Labour for concealed sub main wiring in PVC conduit pipe along with earth wire with FR PVC insulated copper conductor, single core, cable in surface of size 2 x 6 Sqmm + 1 x 6.0 Sqmm earth wire in PVC conduit including all accessories complete all as specified and directed Make :- Finolex / Pestro Plast / Kalinga

Material & Labour for concealed sub main wiring in PVC conduit pipe along with earth wire with FR PVC insulated copper conductor, single core, cable in surface of size 2 x 2.5 Sqmm + 1 x 2.5 Sqmm earth wire in PVC conduit including all accessories complete all as specified and directed Make :- Finolex / Pestro Plast / Kalinga

Material & Labour for concealed sub main wiring in PVC conduit pipe along with earth wire with FR PVC insulated copper conductor, single core, cable in surface of size 4 x 10 Sqmm + 2 x 6.0 Sqmm earth wire in PVC conduit including all accessories complete all as specified and directed Make :- Finolex / Pestro Plast / Kalinga

Supply and fixing of exhaust fan AC 230 / 240V, 450 mm sweep heavy duty complete with louvre including provision of hole for fixing of exhaust fan complet all as specified and directed by the Engineer-in-Charge. Make:- Usha / CG / Havells

S&F highway luminaire LED type with die cast canopy with IP 66 protection, output watt should be 85/90 watt with driver and LED, complete all as specified and directed. Make:- Crompton Cat No - TIP-320-80-57-SL-GL-NSG equivalent in Havells / Panasonic

Material & Labour for Earth contunuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc as required 32 x 6 mm gakvanised strip complete all as specified and directed

Materials and labour for Earthing complete with galvanized steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to GI wire 4mm as earthing lead by means of boths, nuts, check nuts and waasheres of GI or steel, GI strip protected by 40mm bore light grade GI pipe and other end connected to earth test point as directed including funnel with watering pipe 20mm bore light grade galvanised iron, wire mesh, charcoal or coke common salt laid in alternative layer of 15cm (complete thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C1, 50mm thick pre-cast RCC (1:2:4) type B1 normal mix cover slab reinforced with 8mm dia TMT bar 10 10 c/c bothways and single handle of 10mm dia round bar including necessary excavation, earth work etc in soft / loose soil and disposal of soil to a distance n.exc 50m and necessary testing on completion all as shown in electrical plate No 3 MES Schedule Part-I complete all as specified and directed

S & F for Test terminal block made of gun metal or phosphorus bronze size 75 x 75 x 25 mm, drilled and screwed including 3 nos 8 mm dia 25mm long hex head screw including removing of existing test terminal block complete all as specified and directed by Engineer-in-Charge.

Aluminium strip 25 x 3.15mm with saddles and fixing screwes etc for roof conductors and down conductors above ground in high rise bldg of G+3 complete all as specified and directed.

Supply and fixing porcelain vitreous white insulator, fixed on wall / roof / block with galvanised iron nuts, bolts and washers for separating the aluminium or GI earthing strip and wall / roof / block complete all as specified & directed.

Supply and fixing TPN vertical type DBs double door 08 way ( for single / Three Phase Outgoing) suitable for MCB / RCCB / Isolator as incomer CAT No 507747 : Legrand or equivalent product of ABB / Schneider / C&S / Havells

Supply and fixing DPX 3 160 thermal magnetic protection MCCB 160 Amps 4 pole 25 KA of Make: Legrand Cat No : 420057 or equivalent product of L&T / Schnieder / Havells

Supply and fixing Blanking plate for DB

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store and replacement minor parts of metal bush, ball bearing and refixing to its original location after painting of ceiling fans complete, with synthetic enamel paint by spraying including fitting cavities with filler, one coat after cleaning all dust etc all as per directed

Supply & fix wall mounting air circulator fan of sweep 600mm, heavy duty 230 volts AC aupply with oscillating system & with all accessories complete with necessary fixing arrengements on wall / pillar etc complete all as specified and directed Make: Crompton / Usha / Havells

Material and Labour for concealed sub main wiring in PVC conduit with PVC(FRLSH) insulated & unsheathed two runs of 4.0 sqmm single core multistrand copper conductor cable 100 volts grade alongwith one run of 4.0 sqmm PVC (FRLSH) insulated & unsheathed copper conductor cable 1100 Volts grade, connected to common earth dolly as earth continuity conductor drawn through and including PVC casing capping of suitable size including making good of disturbed surfaces complete all as sirected by the ENgineer-in-Charg. Note:- Two runs of 4.0 sqmm and one run of 4.0 sqmm cable and one run of conduit shall be considered as one unit. Make:- Polycab / Havells / RR

S & F Triple pole & Earth enclosure with a three pin and earth plug with socket complete with one tripe pole MCB 32 Amp, 415 V (For equipments)

S & F Triple pole & Earth enclosure with a three pin and earth plug with socket complete with one tripe pole MCB 20 Amp, 415 V (For equipments)

Fire extinguisher (Store pressure type) with MAP 50 ABC dry chemical power suitable for class A, B, C and electrically fire, min discharge time 08 second working temp 10 to 60 degree celsius, Capacity - 02 Kg

All as per item No 168 here-in-before but capacity of 04 Kg

All as per item No 168 here-in-before but capacity of 09 Kg

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ.

Shree Mahabir Builders

TOTCO