SPL REPAIR AND ADDN/ALTN TO BLDG NO P-105, P-106, P-108, P-109 AND P-110 (OFFICER QTR) AT TAGORE LINE UNDER AGE B/R-II AT GE JHANSI

Amount

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

Demolition of cement concrete in ground floor including terrazo flooring and paving n exc 15cm thickness (below or above the ground level) built in cement mortar complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for Refixing or removal to store complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for Refixing or removal to store complete all as specified and directed.

Taking down Chowkats or frames exceeding 1.5 Sq. M but not exceeding 4 Sq. M each (Without taking off shutters from the frame) complete all as specified and directed.

Taking down Chowkats or frames Not exceeding 1.5 Sq. M each (Without taking off shutters from the frame) complete all as specified and directed.

Taking down shutters of any description exc 1.0 Sqm but not exceeding 2.00 Sq. M each complete all as specified and directed.

Demolition of RCC Not exc 15cm thickness Roofs, floors (other than ground floors), beams staircases, landing, chajjas, Cover slab and similar suspended work complete all as specified and directed.

Demolition existing water proofing treatment by brushing with wire brush, cleaning of terracing by taking down cement concrete, existing plaster lime cova 80 to 100mm thick mud phuska/cement concrete/lime concrete etc, cleaning of all foreign material such as fungus mass dust etc, roughing surface of corner to roof by wire brush complete all as specified and directed.

Dismantling for Stone slabs and tiles of any description or thickness in floors, aprons etc, laid dry and pointed in any mortar, complete all as specified and directed.

Dismantling water tank and removing to store exc. 250 litres & not exc. 500 litres capacity of tanks, complete all as specified and directed.

Dismantling Asbestos Cement Corrugated or Semicorrugate in Roof covering, complete all as specified and directed.

Dismantling of Framed timber scantling 40sq cm and over in section in any position complete all as specified and directed.

Dismantling of Framed timber fillet, rails, post, rafters, purlin etc n. exc 40sq cm in section in any position complete all as specified and directed.

Rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 15 mm thick in CM 1:4 on fair faces of brick work or concrete surfaces in two layers(first coat 10 mm & second coat of 5 mm ) mixed with WPC as per menufacturers intructions, finished even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound shall be measured & paid separately.

Rendering 5 mm thick on fair faces of concrete surfaces in ceilings in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and as directed..

Preparing newly plastered surfaces of wall and applying two coats of oil bound distember over 1 mm putty and a coat of chalk whitening primer preparating to make the surface to be plain and smooth before primer complete all as sppecified and directed.

Preparing newly plastered surfaces of wall and applying with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

Preparing newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

Complete removal of exisiting treatment, washing rubbing of old treatment and applying two coats of white wash on wall sufaces complete all as specified and as directed.

All as per Ser item No 23 above but in ceiling complete all as specified and directed.

Complete removal of exisiting treatment, washing and rubbing of old distempered surfaces and applying two coats of oil bound distemper over over 1 mm putty complete all as specified and as directed.

Complete removal of exisiting treatment, washing and rubbing of old distempered surfaces and applying two coats of plastic emulsion paint (washable) of any shade or design as approved by Engr-in-charge over 1 mm putty complete all as specified and as directed.

Preparation of Newly untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of red oxide complete all as specified and directed.

All as per Ser item No 27 above but applying one coat of synthetic enamel paint on old steel surface complete all as specified and directed.

Preparation of New or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of Pink primer complete all as specified and directed.

All as per Ser item 29 above but applying one coat of synthetic enamel paint on old wooden surface complete all as specified and directed.

M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for Coloured Glazed ceramic tiles 300x 600 x 7 to 8 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match including 10mm thick redering in CM 1:4 on wall complete all as specified and directed..

M&L for jointless Virified Ceramic tiles, Dark shake/Double charged/ultra charged,10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6.complete all as specified and directed.

M&L for jointless Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm and not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6.complete all as specified and directed

Ditto all as per item No 34 as above but in skirting including 10mm thick backing coat in CM 1:4 on wall complete all as specified and directed..

M&L for machine cut Kota stone slab flooring 20-25 mm thick and laid over and incl 20 mm thick screed bed in CM (1:6), set and jointed with grey cement slurry mixed with pigment to match the shade of the slab, with and including Cutting / Griding / mirror Polishing on Kota stone as per local trade practice, complete all as specified and directed.

All as per Ser item No 36 above but on vertical surfaces such as skirting/dado over 10mm thick CM rendering in CM 1:4. complete all as specified and directed.

M&L for Granite 20 mm thick over including 10 mm thick CM 1:4 (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rubbing and polishing complete all as specified and as directed.

M&L for 75mm PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in plinth protection and path laid in alternate panels not more than 3 mtr in length, laid to slope 1:30 finished even and smooth without using extra cement complete all as specified and directed.

S&F in repair Aluminium Hat and coat hooks, solid body, 175mm to 250 mm complete all as specified and directed

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered WHITE COLOUR 500 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, complete all as specified and directed. Make : Category-I make will be used.

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered WHITE COLOUR 1000 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, complete all as specified and directed. Make : Category-I make will be used.

S&F 20 mm dia of Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. (minium weight 20 mm-210 gms) etc, complete all as specified and directed.

S&F 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F 16 mm bore Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S & F 20 mm bore Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

M&L for cutting chases,pinning in brick walls for concealed water tubing n.exc 10cm girth and making good facing where required and pointing in CM 1:3 complete all as specified and directed.

S&F in repair Vitreous China table top wash basin, white or off white, flat back, including single lever extended body basin mixer sigle liver (Hindware CAT 280011) or equivalent, waste chain, plug, porcelain stopper, CP waste copling and CP bottle trap complete all as specified and as directed.

Supply & Fix in repairs Vitreous China Squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rests complete all as specified and directed. Make:- Cera (Ist Quality),Parry ware (super fine),Hindware.

Supply & Fix in repairs Vitreous China wash down water closet pan (single unit), EWC, wall mounted/wall hung, white or off white coloured including concealed flushing cistern system & matching coloured seat covered fixed, complete all as specified and as directed. Make:- Hindware (CAT NO 20109) or equivalent in Kohler, Jaquar,Cera.

Supply and Fix in repairs 10 Litres, PVC, valve less, syphonic action type, Flushing Cistern, low level, white inlet, ball valve, float, chain and pull, and brackets including PTMT PVC connection 600mm long and PVC 32 mm dia flush pipe complete all as specified and directed. Make:- Cera,Parry ware,Hindware.

S & F in repairs 15 mm bore Bib taps, fancy type cast copper alloy,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. Make : Category-I make will be used.

S & F in repairs 15 mm bore Bib taps long body fancy type cast copper alloy,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.. Make : Category-I make will be used.

S & F in repairs 15 mm bore stop/angle cock fancy type,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. Make : Category-I make will be used.

S & F in repairs 15 mm bore conceald stop cock fancy type,chromium plated with long shank and cup screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. Make : Category-I make will be used.

S&F in replacement of pillar taps, 15 mm dia, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, complete all specified and directed. Make : Category-I make will be used.

S&F in repair SS grating of square/round shape, overall size of 150x150mm with hinge type openable jali of 100 mm dia size with and incl fixing with CM to floor/nahani traps etc, complete all as specified and directed.

S&F in replacement of PVC connection 450 x 15mm dia PTMT (PVC), complete all as specified and directed.

S & F in repair Chromium plated overhead shower LED (Hindware CAT 160058) including Shower Arm (Hindware CAT 160157) with or without swivel joints, any size, including fixing to steel pipe or CPVC, etc union complete all as specified and directed. Make-Cera (Ist Quality),Parry ware (super fine),Hindware(Ist Quality), Jaquar, Kohler

S&F in repair SS Towel Rail 600mm Long fixed with and including chromium plated brass screws complete all as specified and directed.

S&F in repair of Brass CP connection 15mm dia and 45cm long with 2 Nos brass check nuts with washers for geyser, complete all as specified and directed. Make : Category-I make will be used.

S&F of Ringfit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, complete all as specified and directed.

S&F of PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, complete all as specified and directed.

S&F of Ringfit PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, complete all as specified and directed.

S&F of PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends with access door of any radius, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F PVC (SWR) vent cowl 75mm bore, jointing to waste pipe, complete all as specified and directed.

S&F PVC(SWR) vent cowl 110mm bore, jointing to waste pipe, complete all as specified and directed.

S&F PVC Nahani/ floor trap of 75 mm outlet, jointing to waste pipe, complete all as specified and directed.

M&L for mild steel framed work section as in door or gates of angle or other section with gusset plates,rails braces etc /windows chowkhats/Shutter frame of steel gate of grade Fe-290 (Gde E-165) including all necessary machine wks i.e. cutting, welding, grinding etc, complete all as specified and directed.

M&L for mild steel hold fast and similar small articles conforming to Fe-290 Gde-165, complete all as specified and directed.

M&L for Cutting holes in brick walls (not exc half brick) in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as equired complete all as specified and directed.

S & F for Factory made double extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madecomplete all as specified & directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm (± 5 mm tolerence in dimension) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately)., supplying & fixing in opening as per specification & drawing complete all as specified in SSR Part-II 2020 section 8.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid moulded flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. Note: stainless steel butt hinges and necessary Screws shall be paid separately.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid moulded glazed door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed and as per sample kept in GE office. Note: stainless steel wiremess, butt hinges and necessary shall be paid separately.

S&F in repair of 18/19mm thick WPC Solid board, exterior grade, prelaminated one side with decorative choice laminations and other side balanceing white lamination, fixed with SS screws to WPC frame work in cup boards, and kitchen cabinet rebated complete all as specified and directed.

S&F SS automatic hydraulic concealed type hinges for modular kitchen cabinet including all accessories complete all specified and directed

S&F SS continous piano hinges with flap width of 40 mm complete all specified and directed

S&F SS fancy type handles for modular kitchen cabinet including all accessories as appoved complete all specified and directed

S&F SS kichen basket of any type and any size for modular kitchen cabinet including all accessories complete all specified and directed

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 5 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window n exc 2 sqm) comprising of uPVC multi chambered rame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in epth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area n.exc 1.00 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & complete all as specified and directed. (Glass shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be cceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F of 100mm butt hinges medium weight cold rolled stainless steel ISI marked and fixed with mild steel wood screws or welded to angle frame, complete all as specified and directed.

S&F of 75mm butt hinges medium weight cold rolled stainless steel ISI marked and fixed with mild steel wood screws or welded to angle frame, complete all as specified and directed.

S&F of 200 mm long stainless steel barrel tower bolts, stove enamelled black, with bright bolt and fixed with screws, complete all as specified and directed.

S&F of 150mm long stainless steel pressed handles, oval type, stove enamelled black and fixed with screws, complete all as specified and directed.

S&F of 300mm long stainless steel, sliding door bolt plate type, stove enamelled black, with bright bolt not less than 12mm dia with and incl minimum of 6 bolts and nuts, complete all as specified and directed.

S&F 200 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F of 150mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed.

S&F of 100mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed.

S&F of 150mm aluminum handle cast type anodized complete all specified and directed.

S&F of 100mm aluminum handle cast type anodized complete all specified and directed.

S&F of mild steel ordinary rat tail rod pattern springs of size 300mm including roller and roller plate complete all as specified and directed

S&F for Door stopper 140 mm of aluminium alloy body anodised with tongue of rubber bush at one end fixed to door complete all as specified and directed.

S&F Rubber bush of 25mm long fixed to door complete all as specified and directed.

S&F 125 mm Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc 0.5 Sqm in each pane complete all as specified and directed.

S&F 3mm thick sheet glass frosted/figured and pin headed glazing with oil putty in squares not exc 0.5 Sqm in each pane complete all as specified and directed.

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tacks or galvanized wire staples complete all as specified and directed.

M&L in repair for Aluminium anodised curtain rod 25mm dia with caps/lobs and wall mounting bracket cutting in to length required at site complete all as specified and directed.

S & F in repair for stainless steel kitchen plate rack size 750x 600x230 mm including fixing arrange ment to walls with rawel plug or wooden plugs complete all as specified and directed.

S&F in repair sinks with double bowl of stainless steel 1mm thick kitchen (as per sample kept in GE office ) or laboratory with plugs, washers and waste cupling, wastepipe, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste cupling, wastepipe, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Supply only integral liquid water proofing compound, mixed in CM as per manufacturer instruction, complete all as specified and directed.

M&L for RCC M-25(Nominal Mix)(20 mm stone agg) as in beams complete all as specified and directed.

M&L for RCC M-25(Nominal Mix)(20 mm stone agg) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

All as per Ser item No 113 above but for chajja only all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed

All as per Ser item No 115 above but 6 mm to 8 mm dia complete all as specified and directed.

M&L for mild steel deformed TMT bars 5 mm To 10mm dia (as in reinforcement) cut to length, bent to shape require including cranking, bending spirally for hooking for column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Form work to flat soffits of suspended slabs such as roof slabs, floor slabs and lintels, landingand similar work n exc 200mm thick complete all as specified and directed.

Form work to flat chullah hoods, chajjas, troughs and similar items including edges etc. all as specified and directed.

Form work to sides and soffits of flat floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide all as specified and directed.

All as per Ser item No 121 above but exc 5cm but not exc. 10cm wide complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:3 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement mixed with liquid water proofing solution to vertical surface complete all as specified and directed. Note:-liquid water proofing solution shall be provided in 150ml in 50 Kg of Cement by weight and cost of liquid water proofing solutionmeasured and paid seperate item

Material & labour for sunken slab treatment comprising of the following :- (a) Taking out/ down old existing sunken slab treatment and cleaning the old RCC surfaces of sunken slab including removal of the rubbish from the site of work to a distance n.exc. 250mm compete all as specified and directed.(b) Material & labour for 25mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) over cleaned sunken slab surfaces.(c) Material & labour for applying bituminous priming coat/tack coat over PCC surfaces @ 0.30 Kg per square metre of surfaces. (d) Material & labour for applying bitumin grade 85/25 over priming coat @ 1.20 Kg per Square metre. (e) Material & labour for 25mm thick plastering in CM 1:4 using water proofing compound (WPC) @ 3% by weight of cement. on wall of sunken floor (f) Material & labour for suitable thickness of PCC 1:5:10 type E-2 (using 40mm graded broken brick aggregate) for filling in the sunken portion of slab up to its floor level.(g) Supply & fix of 32mm dia GI pipe medium grade, 450m long 9(for draining out the water) complete all as specified and directed. Note: Floor area and sides of sunken portion shall be measured for payment purpose.

M&L PCC 1:5:10 Type E2 using 40mm brick coarse aggregate as in mass filling in two layer in sunken portion complete all as specified and directed.

M& L for PCC padding 1:2:4 type B1(using 20 mm graded stone aggregate) average thickness 25mm,finished fair and even without using extra cement on roof surfaces complete all as specified and directed.

Material and Labour for 10mm thick cement paster in CM 1:4 mixed with WPC @ 2 % by weight of cement finised even and smooth without using extra cement on roof surface when concreate is green and wall (WPC will be measured and paid seperately as supply only rate) complete all as specified and directed.

Material & labour for cleaning of plastered /concrete surfaces and applying priming coat using bituminous primer @ 0.30 Kg/Sqm. followed by evenly a tack coat @ 1.20 Kg/Sqm. using with 85/25 grade bitumen, over laid with 3mm thick APP modified polymeric water proofing membrane with non woven polyester reinforced of weight not less than 3.6 Kg/Sqm. unrolled and bonded to substance with side and end laps 75mm and 100mm as per manufacturer’s instructions and finished top of APP water proofing polymeric membrane with a coat of hot blown industrial bitumen 85/25 grade @ 1.20 Kg/Sqm and finally finished with a coat of bituminous aluminium paint @ 0.20 Kg/Sqm complete all as specified and directed.

M & L repair to overhang portion of chajja, facia, dropwall etc. for continuous work by providing PCC(1:2:4) Type B-0 and finished with CM(1:3) after taking down of damaged portion of RCC work by maintaining same level and finished the surface to match with the existing surface by providing same finish complete all as specified and directed. (Height of work to be considered above 3.5m and upto 7m from FFL of Ground Floor.) Note : Wherever reinforcement is required to be provided will be paid separately under relevant item and contractor have to inform the department one day in advance after binding of reinforcement for measurement otherwise no payment will be considered on this account.

S&F of pre-painted 0.50mm thick Gavalume Aluminium Zinc coating GI based corrugated / semi corrugated / trapezoidal steel sheet of any colour having tensile strength 550 MPa and AZ 150 grade as in roof covering/cladding to walls, fixed with self tapping screws, complete all as specified and directed.

M&L for structural steel Fe-410-W(Gde-E-250) quality B for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (tubular section, Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, complete all as specified and directed.

Demolition of brick/stone masonary built in cement mortar incl all quoins arches pillars etc complete all as specified and directed.

M&L for brick (Old size brick) work with sub-class B bricks straight or curved on plan exc 6 Mtr mean radius built in CM (1:6) complete all as specified and directed.

S&F in repair Brass CP wall mixer for mixing hot & cold water with overhead shower and handshower provision including handshower of fine quality screwed down for iron pipe and fixed complete all as specified and directed.

S&F of toughned glass corner shelves Shelf of size 300x300 mm fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and directed.

Complete removal of exisiting treatment, washing and rubbing of old surfaces of wall and applying two coats of weather proof exterior grade emulsion over and including a coat of exterior grade cement based primer complete all as specified and directed.

S&F in repair Vitreous China wash hand basin, white, flat back, size 550x400mm excluding taps, waste chain and plug and porcelain stopper but including brackets, CP waste coupling, 32 mm PVC Waste pipe 600mm long complete all as specified and directed.

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern), EWC, coloured including jet system & matching coloured seat covered fixed complete all as specified and directed.

S&F in repair Chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union, complete all as specified and directed.

S&F in repairs 10 Litres capacity, PVC, valve less, symphonic action type, flushing cistern, high level, white inlet, ball valve, float, chain and pull, and brackets including PTMT PVC connection 600mm long and PVC 32 mm dia flush pipe, complete all as specified and directed.

S&F pressed steel frames of size (165mmx60mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

S&F pressed steel frames of size (105mmx60mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

S&F to chowkats, 30mm thick flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F to chowkats, 35mm thick, second class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc complete all as specified and directed.

S&F box type steel window with 80x40x1.25mm RHS frame with side hung shutters (double shutters for glass and gauze) without sash bars, jointed together with and including grills using 12mm square bars @ 10 cm c/c (Ref TD No CEBZ/TD/14/2011) including box type hinges with steel handle and steel peg stay complete with glazing bars dovetailed and welded complete all as specified and directed.

S&F box type steel ventilator with 80x40x1.25mm RHS frame with top hung shutters (double shutters for glass and gauze) without sash bars, jointed together with and including grills using 12mm square bars @ 10 cm c/c (Ref TD No CEBZ/TD/14/2011) including box type hinges with steel handle and steel peg stay complete with glazing bars dovetailed and welded complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. and removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc.complete all as specified and directed.

M&L for point wiring for modular fittings complete with 1.5 Sqmm FRLS insulated, unsheathed, multistranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLS insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm(OD), concealed in wall/ floor etc including provision of modular cover plates with frames and 1.50 sq mm PVC insulated unsheathed stranded copper conductor (FRLS) cable for common earth and connecting to earth dolly all as specified and directed. (Note- rates of chasing/cutting & making goods shall be included in the unit rate) :-

One light point / Bell point controlled by one switch

One ceiling fan point controlled by one switch and regulator

One exhaust fan point controlled by one switch

One ventilating fan point controlled by one switch

One Bell point controlled by one switch

One 6A socket point controlled by one switch on independent board

One 6A socket point controlled by one switch on same board

All as per Ser item No. 148 above but with 4 sq mm FRLS copper wire with 4 Sqmm FRLS copper earth wire for one 16 Amp socket point controlled by one 16 Amp switch on independent board complete all as specified and directed.

M&L for Circuit/submain wiring alongwith earth wire 2 runs x 10 sqmm + 1 run x 10 sqmm with FRLSH insulated copper conductor, single core cable drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc complete all as specified and directed. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length.

All as per Ser item No 150 above but 2runsX4 Sqmm +1runX4Sqmm. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length complete all as specified and directed. Notes for item No. 148 to 151 (i) Quoted rate shall deemed to incude the cost of cutting chases on wall/floor for concealed conduit wiring and making good with cement plaster, putty and paint to match with the existing surface. (ii) If any beam / column / Rock wall is encountered while cutting chases, that particular portion may be provided with PVC casing & caping or surface conduit for drawing cables and surface PVC gang box fully enclosed type for mounting switches, sockets & regulators etc to avoid any damage to the structure. (iii) No cutting shall be done on ceiling for laying PVC conduit for ceiling fan point wiring. Surface conduit or PVC casing caping may be used in that portion.

Supply and fix in replacement of Modular switch 1 way 6A, 1 module 240V, 50Hz with required modular white cover plate with frame including taking down existing unserviceable switch of any description complete all as specified and directed.

Supply and fix in replacement of Modular Socket, 6A - 2/3 pin combined 2 module 240V, 50Hz with required modular white cover plate with frame including taking down existing unserviceable socket of any description complete all as specified and directed.

Supply and fix in replacement of Modular switch 1 way 16A, 1 module 240V, 50Hz with required modular white cover plate with frame including taking down existing unserviceable switch of any description complete all as specified and directed.

Supply and fix in replacement of Modular Socket 6A/16A - 2/3 pin combined 2 module 240V, 50Hz with required modular white cover plate with frame including taking down existing unserviceable socket of any description complete all as specified and directed.

S&F Modular Bulb holder, metal cased, bakelite body, 240 volts, complete all as specified and directed.

Supply and fix in replacement of Modular Bell push 6A 1 module, 240V, 50Hz with required modular white cover plate with frame including taking down existing unserviceable bell push of any description complete all as specified and directed.

S&F electric bell of DINGDONG type, 240 volts, single pole and making all necessary connections, complete all as specified and directed.

S&F, Ceiling rose, three terminals, bakelite body, 240 volts, complete all as specified and directed.

Supply and fix in replacement of Modular fan regulator step type in 5 steps, 240V, 50Hz with required modular white cover plate with frame including taking down existing unserviceable socket of any description complete all as specified and directed.

S & F 9 W White inverter rechargeable LED retrofit lamp, minimum 4 Hr Battery Backp, suitable for B-22 holder base with polycarbonate diffuser and aluminium heat sink complete all as specified and directed.

Supply and fix in replacement of integrated LED batten 20 watt, 4 feet long, full white in Engineering plastic batten with white acrylic cover with built-in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting including taking down existing unserviceable light fitting of any description complete all as specified and directed.

Supply and fix in replacement of integrated LED batten 20 watt, 4 feet long, twin light (cool white & warm white) in Engineering plastic batten with white acrylic cover with built-in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting including taking down existing unserviceable light fitting of any description complete all as specified and directed.

Supply and fix LED batten 10W, 2 feet long, complete with polycarbonate diffuser and built in with electronic driver including connecting up with twin core twisted flexible copper conductor cable form ceiling rose to connector of fitting complete all as specified and directed.

Supply and fix in replacement of LED bulkhead luminaire 10W in die-cast aluminium alloy/ PVC body heat resistant prismatic glass cover, with specially designed gasket for minimum IP 55 degree of protection complete all as specified and directed.

Supply and fix LED building security light fitting 35 watts with high efficiency long life LEDs with In-built electronic driver complete housed in pressure die-cast aluminium housing covered with polycarbonate cover with IP 65degree of protection including GI pipe bracket made up of 25mm dia medium grade GI pipe of length 1.50m bent to required shape and fixing on walls with suitable MS clamps(02Nos) made up of 25mmx4mm MS flat, nuts, bolts and washers and provision of 3 core twisted flexible copper cable 0.5 sqmm from ceiling rose to connector of fitting complete all as specified and directed.

Supply and fix modular MCB protected plug and socket board in sheet steel enclosure with 25A rated mini MCB and 25A rated 3 pin plug, 240 V, 50 Hz complete including cutting the wall surfaces for flush mounting of socket board and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed.

Supply and fix in replacement of ventilating fan with plastic body with louvers, 250mm sweep, single phase, 230 volts, 50 Hz. complete all as specified and directed.

Supply and fix in replacement of sleek round recessed cum surface mounting LED down light 10 W with aluminium die-cast body, finish with drop down PC diffuser warm / full white with optimized heat sink for efficient dissipation including taking down existing unserviceable light fitting of any description complete all as specified and directed.

Supply and fix in replacement of Decorative wall light fixture made up of Polycarbonate with and including 7W retrofit LED lamp(Cool White / Warm White), full white of approved model including taking down existing unserviceable light fitting of any description complete all as specified and directed.

Supply and fix in replacement of 08 W LED Decorative cabinet light, 2 feet, warm white, Aluminium body, 230V complete all as specified and directed.

Supply and fix in replacement of 08 W LED Decorative cabinet light, 4 feet, warm white, Aluminium body, 230V complete all as specified and directed.

Taking down carefully the ceiling fan of any size 1200mm / 1400mm sweep, twin core cable and, dismantling fan blades and deposit to MES store Yard for servicing including supply and replacement of bearings/bushings, capacitor and terminal connector including filling cavities with filler, applying two coat of synthetic enamel spray paint of existing colour, suitable for any model of existing fan etc and incl writing MES No in figure and words in 25 mm wide by synthetic enamel paint of black colour on ceiling fan and Hanging ceiling fan in its existing or new location and connecting up including provision of desired cable from ceiling rose to connector of fan and testing for satisfactory functioning complete all as specified and directed. Note: 1) Rewinding if required shall be measured and paid separately. 2) The work is to be carried out in E/M store yard to the entire satisfaction of Engr-in-Charge.

All as per Ser item No 173 above but of exhaust fan of any size up to 350mm sweep complete all as specified and directed. Note: Rewinding if required shall be measured and paid separately.

Material and labour for Rewinding of Ceiling Fan of size 1200mm / 1400mm sweep by shifting to workshop, cutting and removing of old burnt/damaged winding, cleaning of slots and other parts and rewinding the ceiling fan motor with super enameled copper winding wire of existing gauge with suitable class of insulation, applying varnish, heating, drying, assembling and testing for satisfactory performance complete all as specified and directed.

All as per Ser item No 175 above but exhaust fan of size up to 350mm sweep complete all as specified and directed.

Taking down existing Geyser of capacity 25 Ltrs / 50 Ltrs carefully from its installed position and keeping in safe custody of contractor until the B/R work is completed including replacement of heating element 2.5 kw, thermostat, safety valve and indicator lamp and re-fixing back in its original position duly cleaning the external surfaces, connecting all water and electric connections and testing for satisfactory functioning complete all as specified and directed.

Supply and fix MCCB / MCB distribution board, VTPN, 4 way with MCCB as incomer and MCBs as outgoing in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed. Note: MCCBs / MCBs shall be measured and paid separately.

Supply and fix MCB distribution board, SPN, 12 way with in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed. Note: MCBs shall be measured and paid separately.

Supply and fix MCB distribution board, SPN, 08 way in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed. Note: MCBs shall be measured and paid separately.

Supply and fix MCCB, 125A, 16 KA, 4 Pole complete all as specified and directed.

Supply and fix MCB 40 - 100A, 10 KA, TPN, 'C' curve, 240 V, 50 Hz complete all as specified and directed.

Supply and fix MCB 40A - 63A, 10 KA, SPN, 'C' curve, 240 V, 50 Hz complete all as specified and directed.

Supply and fix MCB 6 - 32A, 10 KA, single Pole, 'C' curve, 240 V, 50 Hz complete all as specified and directed.

Taking down existing unserviceable service cable of any description and Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or strip and overall PVC sheathed, 35sq. mm nominal cross section, 4 core in service connections as per IS 7098(Part 1) including connecting on LT OH line / LT panel /DB with suitable lugs, glands, binding wire etc complete all as specified and directed.

M&L for High density polyethylene pipes (HDPE) 50mm dia of pressure rating 6 kgf/cm2 laid in trenches/floors/duct or fixed on walls /pole for cable protection complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m depth for laying of GI Pipe and getting out in any type of soil complete all as specified and directed.

Returning, filling in, including leveling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removing excavated material not exc 50m and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

M&L for cutting of existing road / hard standing up to 15 cm depth for laying of cables / pipe and making good the disturbed surfaces by providing PCC 1:2:4 after laying of pipes and returning filling of soil, complete all as specified and directed. Note:- Excavation and earth work below road / hard standing will be measured and paid under relevant items.

M&L for earthing complete with galvanized iron earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connecting to GI wire 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel and earth wire protected by 15mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electrical plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and directed. Note :- The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh, protection pipe, earth wire up to 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II.

Supply and fix Hot Press Molded SMC meter box of size not less than 700mm X 480mm X 200mm, double door with transparent glass windows for viewing the meter reading without opening the door, minimum IP-43 degree of protection for indoor use for accommodating 04 Nos X 1 or 3 Phase energy meter including cutting the wall surfaces for flush mounting of meter box and making good with cement plaster, putty and paint to match with the existing surface etc as per site requirement complete all as specified and directed.

Deepesh Electricals

Raja enterprises

jayanti associates