SPECIAL REPAIR OF BLDG NO T-29 OF HQ 118 (I) INF BDE GP CAMP AT NIMU MIL STN UNDER AGE (I) NIMU

Amount

Dismantling timber scantling 40 sqcm and over in section, in any position in framed work in scantling etc complete all as specified and directed by Engr-in-charge.

M&L second class Hard wood in clean sawn timber fixed and fixed in scantlings complete all as specified and directed by Engr-in-charge.

Dismantling timber scantling as in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section in any position as in framed work complete all as specified and directed by Engr-in-charge.

M & L for 2nd class hard wood Plain fillets. exc. 13 & n.exc 25 Sq cm as in square, rectangular or triangular in section, clean sawn, secured with nails or brads complete all as specified and directed by Engr-in-charge..

All as per item No 4 , but exc 3 & n.exc 6 Sq cm in bullnosed, splayed, chamfered or rounded on one edge or face as in beadding complete all as specified and directed by Engr-in-charge.

Dismantling wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness including cover fillets complete all as specified and directed by Engr-in-charge.

M & L Prelaminated particle board 9mm thick, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails in ceiling, flat or sloping to timber frame work complete all as specified and directed by Engr-in-charge.

S&F 9mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination,fixed with nails to timber frame work as in walls all as specified and directed.

Taking down Chowkhats or frames exc 1.5 Sqm but not exc. 4 sq. m each but with shutters (without taking off shutters from the frames) complete all as specified and directed by Engr-in-charge.

Taking down Chowkhats or frames not exc 1.5 Sqm with shutters (without taking off shutters from the frames) complete all as specified and directed by Engr-in-charge.

M&L 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed by Engr-in-charge.

M&L 2nd class hardwood 35mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats for doors complete all as specified and directed by Engr-in-charge.

M&L 2nd class hardwood 30mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed by Engr-in-charge.

S&F Mild steel 100mm long Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed by Engr-in-charge.

S&F Mild steel 75mm long Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed by Engr-in-charge.

S&F extruded aluminium alloy handles, fabricated type, anodised 150mm long complete all as specified and directed by Engr-in-charge.

S&F extruded aluminium alloy handles, fabricated type, anodised 100mm long complete all as specified and directed by Engr-in-charge.

S&F Mild steels sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed 250mm long complete all as specified and directed by Engr-in-Charge.

S&F Aluminium anodised, barrel tower bolt of extruded section and fixed, 150mm long (ISI marked), complete all as specified complete all as specified and directed by Engr-in-charge..

S&F Aluminium anodised, barrel tower bolt of extruded section and fixed, 100mm long (ISI marked), complete all as specified complete all as specified and directed by Engr-in-charge.

Demolition of Cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engr-in-charge

M&L 75mm thick cement concrete type B- 2, 1:2:4 (40mm graded aggregate) complete all as specified and directed by Engr-in-charge

M&L 75mm thick cement concrete type C- 2, 1:3:6 (40mm graded aggregate) as in plinth protection complete all as specified and directed by Engr-in-charge

M&L 75mm thick cement concrete type D- 2, 1:4:8 (40mm graded aggregate) as in sub base complete all as specified and directed by Engr-in-charge

M&L for Chequered cement concrete tiles 20cm x 20cm x25mm thick, set, jointed and pointed in neat cement slurry with grey cement and no pigment in floors over screed bed or bedding layer of mortar 15mm thick in CM 1:4 complete all as spd and directed byEngr-in-charge.

M&L for light shade Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. incl 15mm thick screed bed in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

S & F 3mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed by Engr-in-charge.

M&L for preparation of new wood surfaces of any description, not otherwise descri-bed, over 10cm width or girth and applying two coats of Synthetic enamel (ordinary tint) over a coat of pink primer complete all as specified and directed by Engr-in-charge.

M&L for preparation of old painted steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of Synthetic enamel (ordinary tint) complete all as specified and directed by Engr-in-charge

M&L for preparation of new or previously untreated steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of Synthetic enamel (ordinary tint) over a coat of Red oxide, zinc chrome primer complete all as specified and directed by Engr-in-charge

Dismantling Plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings

S&F for 0.63mm Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type hook and washers, in roofs, walls etc. with grade of zinc coating 275.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L for Precast cement concrete block in PCC 1:3:6 type C1 (using 20 mm graded aggregate) masonry with solid block exc. 10 cm in width and setting in mortar 1:4 complete all as specified.

Demolition of precast concrete block walling masonry, built in cement mortar

M&L for Rendering 15mm thick on fair faces of concrete block masonry surfaces in cement mortar (1:4)

M&L for Rendering 10mm thick on fair faces of concrete block masonry surfaces in cement mortar (1:6)

M&L preparing new plastered surfaces of walls and applying two coat of cement base paint over a coat of primer all as specified and directed by Engr-in-charge.

M&L preparing new plastered surfaces of walls and Chalk whiting, on plastered surfaces, prepara-tory to distempering applying two coat of Distemper oil emulsion white or tinted

S&F Rolled mils steel sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc. Fe 410 -W (Gde-E- 250) quality-A

Dismantling wrought iron or mild steel work of any description not otherwise provided for

M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. over 15mm thick Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

M&L glazed ceramic tile " coloured" 450mmx 300mm x 7mm as in verticle surface such as skirting /dado etc, set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match the shade of tile, fixed over and incl 10mm thick bedding layer in cement mortar 1:4 on concrete block wall surface complete all as specified.

Taking down or up steel tubing and connections incl cleaning for refixing or removal to store for 15 mm dia bore.

S&F for 25mm outer dia 3-layer PP-R P o l y p r o p y l e n e random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded p o l y p r o p y l e n e random fittings fixed complete to walls, ceilings or in floors etc.

Dismantling broken water tank of cap exc 500 ltr but n exc 1000 ltr

S&F for 1000 ltr cap Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I

S&F in repair vitreous China squatting pan, ‘Orissa’ pattern, size 630 x 450 mm white, with integral foot rests (excluding flushing cistern and flush pipe) Squatting pan including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor

S&F in repair PVC valveless 10 ltr cap, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets

S&F in repair Vitreous China wash basin, white, flat back,size 550x400mm ovel type/round/anyshape including brackets and pedestal complete in all respect as specified.

S&F in repair Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets,flush pipe, grating and Union fordischarge pipe. (Exclusive offixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified.

S&F in repair 15mm fancy type Bib taps, Chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S&F in repair 15mm dia Angle cock/Stop valves, cast copper alloy,screwed down, high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed complete all as specified.

S&F in repair for 15mm PVC connections of 600mm long with PTMT nuts complete all as specified.

S&F in repair 15mm dia Fancy type Pillar taps, cast copper alloy, with capstan heads,chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified.

Demolition of stone/boulders masonry, laid dry complete all as specified.

Demolition of stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

M&L for stone masonry Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:4, complete all as specified.

M&L for stone masonry Walling of random rubble, uncoursed, well bonded, and solidly heartd laid dry as directed and as specified.

Demolition of Reinforced Cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) (reinforcement cut as required to facilitate demolition)

Use & waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not ex ceeding 200mm thick with flat rough finished surfaces of concrete, complete all as specifed and directed by Engr-in-charge.

M&L for RCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams, and columns in floors, roofs complete all as specified and directed by Engr-in-charge.back in cement; fixing automatic flushing cistern with brackets,flush pipe, grating and Union fordischarge pipe. (Exclusive offixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified.

M&L for cement concrete 1:4:8 type D2 (using 40mm graded crushed stone aggregate ) in foundation, filling and mass concrete complete all as specified and directed by Engr-in-charge.

M&L for Precast reinforced cement concrete, type B-1, 1:2:4 (Using 20mm graded crushed stone aggregate) as in manhole cover set in cement mortar 1:4, compete all as specified and directed.

M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar of internal dia 75-100mm incl any earth work and demolition of PCC complete all as specified and directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or floor of 110mm bore pipe complete all as specified and directed by Engr-in-charge

S&F for 110 mm bore PVC (SWR) bends any radius ® complete all as specified and directed by Engr-in-charge

S&F PVC (SWR) Vent cowl of 110mm bore, complete all as specified as directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or floor of 75mm bore pipe complete all as specified and directed by Engr-in-charge

S&F PVC (SWR) floor trap of 75mm plain with grating including jointing with solvent cement

M&L for 100mm thick cement concrete 1:3:6 type C2 bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested;

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc

M&L repair for point wiring with PVC insulated single core cable of stranded copper conductors of size 1.5 sqmm, 1100 volt grade drawn in and including rigid PVC casing caping accessories lain on wall/ceiling surface and fixed with PVC saddles and back-plate and GI screws, including PVC insulated single core cable of stranded copper conductor of size 1.5 sqmm as earth continuous wire connected to common earth and PVC Board for housing like switches, sockets, fan regulators etc. One light point/ one fan point controlled by one switch.

M&L repair for point wiring with PVC insulated single core cable of stranded copper conductors of size 1.5 sqmm, 1100 volt grade drawn in and including rigid PVC casing caping accessories lain on wall/ceiling surface and fixed with PVC saddles and back-plate and GI screws, including PVC insulated single core cable of stranded copper conductor of size 1.5 sqmm as earth continuous wire connected to common earth and PVC Board for housing like switches, sockets, fan regulators etc. One 3 pin 5 amps socket outlet independent with cables 1.5 sqmm size.

M&L repair for point wiring with PVC insulated single core cable of stranded copper conductors of size 1.5 sqmm, 1100 volt grade drawn in and including rigid PVC casing caping accessories lain on wall/ceiling surface and fixed with PVC saddles and back-plate and GI screws, including PVC insulated single core cable of stranded copper conductor of size 1.5 sqmm as earth continuous wire connected to common earth and PVC Board for housing like switches, sockets, fan regulators etc. One 3 pin 5 amps socket outlet on same board.

All same as per item No 76 above but with conductor of size 4 sqmm (Nominal area) for one 3 pin socket outlet 15 Amps on independent board complete and earth continuity wire with 4 sqmm PVC insulated stranded copper conductor Cable.

S&F repair socket 2 in 1, 5 pin 5 Amp flush type complete all as specified.

S&F repair switch piano flush type 5 Amp, single pole, one way complete all as specified and directed.

S&f repair Switch socket combination 2 in 1, 3 pin, 5 Amp flush type complete all as specified and directed.

S&F in Repair switch Socket Combination 2 in 1, 3 pin, 15/16 amp flush type Universal complete all as specified and directed.

M&L in repair for ceiling rose surface Bakelite 65x50mm two to three terminal complete all as specified and as directed by Engr-in-Charge.

S&F in repair basic all purpose surface and wall mounted LED batten with polycarbonate housing and integreted electronic driver of cap 20 watt, 4 feet long, with all accessories complete all as per specified and as directed by Engr-in-Charge.

Supply and fixing LED lights fittings 10/12 watt, 220 v, AC decorative box type with driver , holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S & F LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

S&F in repair sheet metal powder coated versatile Double door SPN distribution board, 12 way suitable for MCB's fitted with copper bus bar rated 200amps, neutral link , earth bar and din rail suitable for use on 240 Volt, 50Hz .

S&F in repair sheet metal powder coated versatile Double door SPN distribution board, 08 way suitable for MCB's fitted with copper bus bar rated 200amps, neutral link , earth bar and din rail suitable for use on 240 Volt, 50Hz .

M&L in repair for MCB SPN 63 Amp, 240V with 10KA breaking capacity of 'C' series in distribution boards all as specified and directed.

S&F in repairs to MCB SP 6-32 Amp with 10KA breaking capacity of 'C' series in distribution boards all as specified and directed.

Supply and fix in repair exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz,RPM 1200,Copper winding of sweep 250mm.

Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6.3) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, surrounded on all sides by alternate layers of 150 mm thick charcoal and common salt, connected to galvanized earh lead wire of size 4.0 mm dia by means of lugs, bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3, wire protected by dia 15 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI light grade including wire mesh funnel, PCC, earth chamber pit with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame necessary excavation and earth work in any type of soil including testing on completion for desired result all as specified.

Taking out old unserviceable underground cable of any size/ make/ type etc from excavated trenches/ on poles/ passing through pipes etc from different locations complete all as spd.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3½ core

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for taking out pipe line etc for repairs / laying cables etc and getting out in soft / loose soil complete all as specified and as directed by the Engineer - in - Charge.

Excavation in trenches by cutting of road crossing/PCC hard standing, under boundary wall for laying of pipe/cable including making good the existing surface with same finish to match the original finish complete all as specified and directed by Engr-in-charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and as directed by the Engineer - in - Charge.

Removal of excavated material [soil] to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed by the Engineer - in - Charge.

Material and labour for un reinforced pre cast concrete cable cover class LV type I, flat size 250 mm x 150 mm x 40 mm.

Sand cushioning to under ground cable complete all as specified in clause 19.75 of SSR Part - I.

Supply and fix or laying in trenches/on wall/poles/structures as in repairs 80 mm dia GI tubing light grade for road crossing/for cable protection/fixing of pigmi lights etc,of the following sizes including necessary provision for cable entry if reqd in pigmi lights pole, fixing screws complete as required complete all as specified and directed by Engr-in-charge.

Supply and fix or laying in trenches/on wall/poles/structures as in repairs 50 mm dia GI tubing light grade for road crossing/for cable protection/fixing of pigmi lights etc,of the following sizes including necessary provision for cable entry if reqd in pigmi lights pole, fixing screws complete as required complete all as specified and directed by Engr-in-charge.

Dismantling and Taking down LT U/S panels incl all outgoing and incoming connections and making good the disturbed area from site all as specified and directed by Engineer-in-Charge.

M&L for Busbar chambers with 4 aluminium busbar strip of rating 400 Amp 6 way fixed on angle iron of size 40mm x40mm x5mm complete all as specified and directed by Engineer in Charge.

M & L for Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6.3) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, surrounded on all sides by alternate layers of 150 mm thick charcoal and common salt, connected to MS galvanized earh strip of size 32 x 6 mm by means of lugs, bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3, wire protected by dia 15 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI light grade including wire mesh funnel, PCC, earth chamber pit with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame necessary excavation and earth work in any type of soil including testing on completion for desired result all as specified.

M/S ZTECH (BID ID -3341886)

M/S WEB COMPNAY (BID ID -3341373)

N K BUILDERS (BID ID -3341616)

national engineering (BID ID -3341965)

RND ENGINEERS & CONTRACTORS (BID ID -3342113)

M/S LIBE & CO (BID ID -3341980)

M/S OSHO TRADERS (BID ID -3342103)