Provision of Wayfinding/signage at AAI, DEOGHAR AIRPORT, DEOGHAR

Amount

Airport Entry Portal Refer design drawing 1.1S, 1.1G Providing and fixing Non-illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge. All exteriorsigns should be manufatured considering harsh outdoor conditions, weatherproofing techniques and materials shall be used.>> Sign face Providing and fixing sign face panels 3mm thick Aluminium sheet fabrication, Aluminium sheet fixed to horizontal structural truss. White retro-reflective vinyl pasted over edge to edge aluminium sheet. Graphics in plotter cut RAL 5013 exterior grade opaque vinyl pasted over white retroreflective vinyl. Sign Frame (Spanning Truss) Providing and fixing sign frame (Horizontal Spanning truss) in M.S. square section hotdipped galvanised as per drawing. Frame to be directly fixed to the sign structure. Frame to receive the sign faces. Sign Structure Providing a Square Sign post of 300 x 300 mm, 5.4mm thick MS hollow sections including welded Base plate in 8mm thick MS Plate and Gussets in 6mm thick MS Plate as per drawing with holes to fix it on holding down bolts anchored in concrete footing. The post shall be closed with a 6 mm thick MS plate and parts kept unpainted to weld the sign structure as per the drawing to ensure a rigid connection at site. The entire post assembly shall be hotdipped galvanised and P.U. Painted to match RAL 9006 as specified and approved by the Engineer-In-charge. The Post shall be always be a single contnuous element without any joints.Cost to include all activities and temporary props used for a perfect vertical in plumb installation, shim Plates for adjustment of levels and filling the gap with concrete slury etc required for fixing the sign in an external location. The actual structural design of the sign for its stability shall be responsibility of the EPC contractor. Spanning truss shall be designed for each Mounting square section span and the wind loads. Foundation Providing and laying foundation for the sign including its compaction and all activities like Excavation, PCC base layer, providing and fixing in position electrical connection wherever applicable and finished as per drawing. The item cost includes cutting and opening the floor finish at location, and making good the location to the match the original finish after fixing and installation of sign >> Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Vehicular Directional Sign - Pole Mounted Refer design drawing 1.3a-1S, 1.3a-1G Providing and fixing Non-illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge. All exterior signs should be manufatured considering harsh outdoor conditions, weatherproofing techniques and materials shall be used.>> Sign Face Providing and fixing sign face panels 3 mm thick Aluminium sheet fabrication, Aluminium sheet fixed to sign frame. White retro-reflective vinyl pasted edge to edge over aluminium sheet. Graphics in plotter cut RAL 5013 exterior grade opaque vinyl pasted over white retroreflective vinyl. Sign Frame Providing and fixing sign frame 50 x 50 x 2 mm in M.S. square section hotdipped galvanised and P.U.Painted to match RAL 9006 as per drawing. Frame to be directly fixed to the sign structure. Frame to receive the sign faces. Sign Structure MS square post 125x125x4 and horizontal square sections 75x75x2.5mm, hotdipped galvanised and powder coated to match RAL 9006. Post including welded MS base Plate and Gussets in 6mm thick MS Plate as per drawing with holes to fix it on holding down bolts anchored in concrete footing. The post shall closed with a 3 mm thick MS plate and parts kept unpainted to weld the sign structure as per the drawing to ensure a rigid connection at site. The entire post assembly shall be hotdipped galvanised and P.U. Painted to match RAL 9006 as specified and approved by the Engineer-In-charge. The Post shall be always be a single continuous element without any joints.Cost to include all activities and temporary props used for a perfect vertical in plumb installation, shim Plates for adjustment of levels and filling the gap with concrete slury etc required for fixing the sign in an external location.The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. 225 x 225 mm size, 5 mm thick cover plate mounted in case the flooring is present. Foundation Providing and laying foundation for the sign including its compaction and all activities like Excavation, PCC base layer, providing and fixing in position electrical connection wherever applicable and finished as per drawing. The item cost includes cutting and opening the floor finish at location, and making good the location to the match the original finish after fixing and installation of sign >> Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Pedestrian Directional Sign Refer design drawing 1.3bS, 1.3bG Providing and fixing Non-illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge. All exterior signs should be manufatured considering harsh outdoor conditions, weatherproofing techniques and materials shall be used.>> (Providing and fixing of suitable bird spikes with 50mm height made up of Poly carbonate etc. as required.) Sign Face Providing and fixing sign face panels 3 mm thick Aluminium sheet fabrication, Aluminium sheet fixed to sign frame. White retro-reflective vinyl pasted over edge to edge aluminium sheet. Graphics in plotter cut RAL 5013 exterior grade opaque vinyl pasted over white retroreflective vinyl. Logo graphics in printed vinyl pasted on the sign face with easy replacability.(Wherever Signle side content provided then other side Aluminium sheet to be painted with two coats of PU paint) Sign Frame Providing and fixing sign frame 50 x 50 X 2.5 mm including Horizontal Square sections in M.S. square section 50 microns hotdipped galvanised and two coats of P.U.Painted to match RAL 9006 as per drawing. Frame to be directly fixed to the sign structure. Frame to receive the sign faces. Sign Structure MS square post 70 x 70 x 3 mm, 50 microns hotdipped galvanised and powder coated to match RAL 9006. Post including welded MS base Plate and Gussets in 6mm thick MS Plate as per drawing with holes to fix it on holding down bolts anchored in concrete footing. The post shall closed with a 3 mm thick MS plate and parts kept unpainted to weld the sign structure as per the drawing to ensure a rigid connection at site. The entire post assembly shall be 50 microns hotdipped galvanised and two coats of P.U. Painted to match RAL 9006 as specified and approved by the Engineer-In-charge. The Post shall be always be a single continuous element without any joints.Cost to include all activities and temporary props used for a perfect vertical in plumb installation, shim Plates for adjustment of levels and filling the gap with concrete slury etc required for fixing the sign in an external location.The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. 225 x 225 mm size, 5 mm thick cover plate mounted in case the flooring is present. Foundation Providing and laying Cement Concrete foundation for the sign including its compaction and all activities like Excavation, PCC base layer, providing and fixing in position and finished as per drawing. The item cost includes cutting and opening the floor finish at location, and making good the location to the match the original finish after fixing and installation of sign >> Accessories: Providing and fixing all accessories such as nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Traffic Statutory Sign Refer design drawing 1.4aS, 1.4aG Providing and fixing Non-illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge. All exterior signs should be manufatured considering harsh outdoor conditions, weatherproofing techniques and materials shall be used.>> Sign Face Providing and fixing sign face panels 3 mm thick Aluminium sheet fixed to sign structure. White retro-reflective vinyl pasted over edge to edge aluminium sheet. Graphics in plotter cut red Pantone 485C and black Pantone 6C exterior grade opaque vinyl pasted over white retroreflective vinyl. Sign Structure MS square post 50x50, hotdipped galvanised and P.U. painted to match RAL 9006 grouted in ground. The actual structural design of the sign for its stability shall be responsibility of the EP Ccontactor. Secret fixing methods should be used to fix parts together. Foundation Providing and laying foundation for the sign including its compaction and all activities like Excavation, PCC base layer, providing and fixing in position electrical connection wherever applicable and finished as per drawing. The item cost includes cutting and opening the floor finish at location, and making good the location to the match the original finish after fixing and installation of sign >> Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Entry / Exit Announcer Refer design drawing 1.6bS, 1.6bG Type A Providing and fixing Non-illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge. All exterior signs should be manufatured considering harsh outdoor conditions, weatherproofing techniques and materials shall be used.>> Sign Portal : Type B Type B: In case of no portal, 50mm deep portal has to be fabricated from 3 mm thick Aluminium Composit Panel with 0.25 mm PVDF, exterior grade with manufacturers warranty and test certficate from principle OEM from ALUDECOR / ALUCOBOND or equivalent make, with Yellow Pantone 116C Vinyl Stuck over it. The internal structural frame to be made from 50 X 50 x 2 mm aluminium box section. Sign Letters Providing and fixing Primary channel letters 50mm thk and Secondary profile cut letters 10mm thk, 3D cut letters in black glossy acrylic.All the letters would be made in profile to achieve true right angle. All mounting would be done in true plumb and using templet, keeping the alignment of the letters in one level.

Facility Announcers - Floor Mounted Refer design drawing 1.7aS, 1.7aG Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge. All exterior signs should be manufatured considering harsh outdoor conditions, weatherproofing techniques and materials shall be used.>> Sign Box Providing and fixing sign box with lasercut Bent Fabrication in 8mm thick clear acrylic with pantone yellowC Vinyl pasted over acrylic with white diffuser film on inside face. Blockout vinyl for text Pantone Black 6C. Complete box excluding bottom side is lited with internal LED lighting. Acrylic fabrication shall have transparent structural supports for obstruction free lighting. Box to be directly mounted on the sign structure. Bottom panel Bottom MS Panel powder coated in colour to match Vinyl Black of Pantone Black 6C. Sign Structure Providing and fixing MS square post 75 x 75 x 2.5 mm, hotdipped galvanised and P.U. painted to match RAL 9006 grouted in ground. The Post shall be always be a single contnuous element without any joints .Cost to include all activities and temporary props used for a perfect vertical in plumb installation, shim Plates for adjustment of levels and filling the gap with concrete slury etc required for fixing the sign in an external location.The actual structural design of the sign for its stability shall be responsibility of the EP Ccontactor. Secret fixing methods should be used to fix parts together. Lighting All internal illumination shall be using Power LED Lights from Osram or equivalent with electronic controllers, having even spread and overlaps to avoid banding and dark spots and adhering to the LUX levels mentioned in the performance specification.Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. Foundation Providing and laying foundation for the sign including its compaction and all activities like Excavation, PCC base layer, providing and fixing in position electrical connection wherever applicable and finished as per drawing. The item cost includes cutting and opening the floor finish at location, and making good the location to the match the original finish after fixing and installation of sign >> Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Facility Announcers - Wall Mounted Refer design drawing 1.7bS, 1.7bG Providing and fixing Non-illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge. All exterior signs should be manufatured considering harsh outdoor conditions, weatherproofing techniques and materials shall be used.>> Sign Face Plotter cut Blockout vinyl Pantone Yellow C, vinyl for text Pantone Black 6C as per graphics, pasted over 8mm thick White translucent 040 acrylic. Sign Structure 25mm wide powder coated, colour RAL 9006 aluminium extrusion with inbuilt frame to recieve the sign face. The panel should be made easily openable for maintainance. Secret fixing methods should be used to fix parts together. Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Terminal Building Announcer Refer design drawing 1.8S, 1.8G Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge. All exterior signs should be manufatured considering harsh outdoor conditions, weatherproofing techniques and materials shall be used.>> (Considering 14 Alphabets for English & 12 Alphabets Hindi). Letter face Providing and fixing White translucent 040, 5mm thick acrylic. complete face shall be covered with translucent vinyl film to match Blue Pantone 541C. Back Channel The channel letters would be made out of 3 mm thick aluminium to receive the front acrylic and house the controller and LEDs with keeping face of the letters 10mm recessed as per drawing. All the letters would be made in profile to achieve true right angle. All mounting would be done in true plumb and using templet, keeping the alignment of the letters in one level. Spacer Recommended for use for mounting the larger text on the glazing frame Lighting All internal illumination shall be using Power LED Lights from Osram or equivalent with electronic controllers, having even spread and overlaps to avoid banding and dark spots and adhering to the LUX levels mentioned in the performance specification.Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Ceiling Hung Directional Sign Refer design drawing 2.1aS, 2.1aG Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Sign face shall be made in 8mm thick 040 white acrylic (as specified) having graphics pasted in Plotter cut Blockout vinyl. Entire panel covered with a protective overlaminate. The films to wrap around the edge of the acrylic to a distance of 25mm on the back side. The Plotter cut blockout vinyl shall match the specified colour (colour Pantone Black 6C) and vinyl for text Pantone yellow C or Cyan 311C as per graphics and of specified make duly approved by the Engineer-in-Charge. we would suggest Vinly form 3M or avery viny Sign Frame Providing and fixing sign frame 50mm wide Powder coated, colour RAL 9006 special aluminium extrusion with inbuilt frame to recieve the sign face. The sign face shall be fixed to sign frame with 3M brand dual lock syatem in one side and 3M bothway tape from the other side.The panel should be made easily openable for maintainance. Sign internal Structure Providing and fixing Framewrok of Aluminium 25mmx 25mm hollow square sections. Shall be directly fixed to the sign frame. Suspender Providing and fixing Stainless steel 35 x 35mm Hollow sections (assuming typical length of 1 metre) mounted on slabs/beams/walls. All hardware used for fixing of sign shall be Stainless steel. Lighting All internal illumination shall be using Power LED strip edge Lights with electronic controllers, having even spread and overlaps to avoid banding and dark spots.Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Floor mounted directional sign - Without FIDS Refer design drawing 2.1b-2G Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Sign face shall be made in 8mm thick 040 white acrylic (as specified) having graphics pasted in Plotter cut Blockout vinyl. Entire panel covered with a protective overlaminate. The films to wrap around the edge of the acrylic to a distance of 25mm on the back side. The Plotter cut blockout vinyl shall match the specified colour (colour Pantone Black 6C) and vinyl for text Pantone yellow C or Cyan 311C as per graphics and of specified make duly approved by the Engineer-in-Charge. we would suggest Vinly form 3M or avery vinyl Sign Frame Providing and fixing sign frame 50mm wide powder coated, colour RAL 9006 special aluminium extrusion with inbuilt frame to recieve the sign face. The sign face shall be fixed to sign frame with the 3M brand dual lock system in one side and 3M bothway tape from the other side. The panel should be made easily openable for maintainance. Sign Structure All structural members in SS square post 100 x 100 and horizontal cross tie member square sections 75x75mm, brush finished. base plate embedded below the floor finish and provided with a floor trim ring. All hardware used for fixing of sign shall be Stainless steel.Post including SS base Plate and Gussets in 6mm thick SS Plate as per drawing with holes to fix it on holding down bolts anchored in concrete slab. The post shall closed with a 3 mm thick SS plate as specified and approved by the Engineer-In-charge. The Post shall be always be a single contnuous element without any joints.Cost to include all activities and temporary props used for a perfect vertical in plumb installation, etc required for fixing the sign in an internal location. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Information Panel Providing and fixing FIDS (lcd screen 46”) mounted on cross ties with brackets designed for the specific sizes. Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. Lighting All internal illumination shall be using Power LED strip edge Lights with electronic controllers, having even spread and overlaps to avoid banding and dark spots.Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Foundation Providing and laying foundation for the sign including its compaction and all activities like Excavation, PCC base layer, providing and fixing in position electrical connection wherever applicable and finished as per drawing. The item cost includes cutting and opening the floor finish at location, and making good the location to the match the original finish after fixing and installation of sign >> Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Wall Mounted Facility Announcer Refer design drawing 2.2a-S, 2.2a-G Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Sign face shall be made in 8mm thick 040 white acrylic (as specified) having graphics pasted in Plotter cut Blockout vinyl. Entire panel covered with a protective overlaminate. The films to wrap around the edge of the acrylic to a distance of 25mm on the back side. The Plotter cut blockout vinyl shall match the specified colour (colour Pantone Black 6C) and vinyl for text Pantone yellow C or Cyan 311C as per graphics and of specified make duly approved by the Engineer-in-Charge. Sign Frame Providing and fixing sign frame 50mm wide powder coated, colour RAL 9006 special aluminium extrusion with inbuilt frame to recieve the sign face. The sign face shall be fixed to sign frame with the 3M brand dual lock system in one side and 3M bothway tape from the other side.The panel should be made easily openable for maintainance. Lighting All internal illumination shall be using Power LED Lights from Osram or equivalent ( Edge lighting - 6500K, 24 v, with optimal homogenious backlighting & light Throw of minimum 4 ft) with electronic controllers, having even spread and overlaps to avoid banding and dark spots and adhering to the LUX levels mentioned in the performance specification.Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Wall Projected Facility Announcer Refer design drawing 2.2b-S, 2.2b-G Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Sign face shall be made in 8mm thick 040 white acrylic (as specified) having graphics pasted in Plotter cut Blockout vinyl. Entire panel covered with a protective overlaminate. The films to wrap around the edge of the acrylic to a distance of 25mm on the back side. The Plotter cut blockout vinyl shall match the specified colour (colour Pantone Black 6C) and vinyl for text Pantone yellow C or Cyan 311C as per graphics and of specified make duly approved by the Engineer-in-Charge. Sign Frame Providing and fixing sign frame 50mm wide powder coated, colour RAL 9006 special aluminium extrusion with inbuilt frame to recieve the sign face. The sign face shall be fixed to sign frame with the 3M brand dual lock system in one side and 3M bothway tape from the other side.The panel should be made easily openable for maintainance. Lighting All internal illumination shall be using Power LED Lights from Osram or equivalent ( Edge lighting - 6500K, 24 v, with optimal homogenious backlighting & light Throw of minimum 4 ft) with electronic controllers, having even spread and overlaps to avoid banding and dark spots and adhering to the LUX levels mentioned in the performance specification.Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Counter mounted facility Announcer - With Screen Ref Design drawing 2.2d - 2S, 2.2d - 2G Check in Counter Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Sign face shall be made in 5 mm thick 040 white acrylic (as specified) having graphics pasted in Plotter cut vinyl. Entire panel covered with a protective overlaminate. The films to wrap around the edge of the acrylic to a distance of 25mm on the back side. The Plotter cut blockout vinyl shall match the specified colour (colour Pantone Black 6C) and vinyl for text Pantone yellow C or Cyan 311C as per graphics and of specified make duly approved by the Engineer-in-Charge. we would suggest Vinly form 3M or avery vinyl Sign face shall be provided with through and through cutout to accomodate 32" FIDS Information Panel / FIDS 32" Digital screens mounted on cross ties internally, with brackets designed for the specified sizes. The screen shall be provided by AAI. Sign Frame Providing and fixing sign frame 100 mm wide powder coated, colour RAL 9006 special aluminium extrusion with inbuilt frame to recieve the sign face. The sign face shall be fixed to sign frame with the 3M brand dual lock system in one side and 3M bothway tape from the other side.The panel should be made easily openable for maintainance. Sign Structure All structural members in SS square post 100 x 100 mm, brush finished. base plate embedded below the floor finish and provided with a floor trim ring. All hardware used for fixing of sign shall be Stainless steel.Post including SS base Plate and Gussets in 6mm thick SS Plate as per drawing with holes to fix it on holding down bolts anchored in concrete slab. The post shall closed with a 3 mm thick SS plate as specified and approved by the Engineer-In-charge. The Post shall be always be a single contnuous element without any joints.Cost to include all activities and temporary props used for a perfect vertical in plumb installation, etc required for fixing the sign in an internal location. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Boarding Gates - Wall Mounted ( To be Fixed to the Ceiling) Refer design drawing 2.2g3-S, 2.2g3-G without FIDS Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> (Wherever Signle side content provided then other side shall be provided with ACP) Sign face Sign face shall be made in 5 mm thick 040 white acrylic (as specified) having graphics pasted in Plotter cut Blockout vinyl. Entire panel covered with a protective overlaminate. The films to wrap around the edge of the acrylic to a distance of 25mm on the back side. The Plotter cut blockout vinyl shall match the specified colour (colour Pantone Black 6C) and vinyl for text Pantone yellow C or Cyan 311C as per graphics with a provision of through and through cut out for information panel.and of specified. Sign Frame Providing and fixing sign frame 50mm wide powder coated, colour RAL 9006 special aluminium extrusion with inbuilt frame to recieve the sign face. The sign face shall be fixed to sign frame with the 3M brand dual lock system.The panel should be made easily openable for maintainance. Sign internal Structure Providing and fixing Framewrok of Aluminium 25mmx 25mm x 1.5 mm hollow square sections. Shall be directly fixed to the sign frame. Information Panel / FIDS Providing & fixing 32" LED screens mounted on cross ties internally, with brackets designed for the specified sizes. Lighting All internal illumination shall be using Power LED Lights( Edge lighting - 6500K, 24 v, with optimal homogenious backlighting & light Throw of minimum 4 ft) with electronic controllers, having even spread and overlaps to avoid banding and dark spots and adhering to the LUX levels mentioned in the performance specification.Cost to include all internal connections and Wiring, terminating and connecting with the incoming cable at the site. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Belt No. sign Refer design drawing 2.2h-S, 2.2h-G Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign Box Providing and fixing sign box with lasercut Bent Fabrication in 8mm thick clear acrylic with pantone yellowC Vinyl pasted over acrylic with white diffuser film on inside face. Blockout vinyl for text Pantone Black 6C. Complete box excluding bottom side is lited with internal LED lighting. Acrylic fabrication shall have transparent structural supports for obstruction free lighting. Box to be directly mounted on the sign structure. Bottom panel Bottom MS Panel powder coated in colour to match Vinyl Black of Pantone Black 6C. Sign Structure : Type 2 All structural members in SS square post 75 x 75 mm (assuming typical length of 2.7 metre), brush finished. base plate embedded below the floor finish and provided with a floor trim ring. All hardware used for fixing of sign shall be Stainless steel.Post including SS base Plate and Gussets in 6mm thick SS Plate as per drawing with holes to fix it on holding down bolts anchored in concrete slab. The post shall closed with a 3 mm thick SS plate as specified and approved by the Engineer-In-charge. The Post shall be always be a single contnuous element without any joints.Cost to include all activities and temporary props used for a perfect vertical in plumb installation, etc required for fixing the sign in an internal location. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together.

Washroom / Drinking Water / Baby care Refer design drawing 2.4a-S, 2.4a-G Providing and fixing illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Sign face shall be made in 8mm thick 040 white acrylic (as specified) having graphics pasted in Plotter cut Blockout vinyl. Entire panel covered with a protective overlaminate. The films to wrap around the edge of the acrylic to a distance of 25mm on the back side. The Plotter cut blockout vinyl shall match the specified colour (colour Pantone Black 6C) and vinyl for text Pantone Cyan 311C as per graphics and of specified make duly approved by the Engineer-in-Charge. we would suggest Vinly form 3M or avery vinyl Sign Frame Providing and fixing sign frame 50mm wide powder coated, colour RAL 9006 special aluminium extrusion with inbuilt frame to recieve the sign face. The sign face shall be fixed to sign frame with the 3M brand dual lock system in one side and 3M bothway tape from the other side.The panel should be made easily openable for maintainance. Lighting All internal illumination shall be using Power LED strip edge Lights with electronic controllers, having even spread and overlaps to avoid banding and dark spots.Cost to include all internal connections and Wiring, terminating and connecting the incoming cable laid by Airport contractor at the site. The actual structural design of the sign for its stability shall be responsibility of the EPC contactor. Secret fixing methods should be used to fix parts together. Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing.>>

Service Areas Refer design drawing 2.4b-G Providing and fixing non-illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications, signage schedule and to the satisfaction of the Engineer-in-Charge.>> Sign face Digitally printed Graphics on vinyl pasted on 3mm thick black acrylic mounted on walls/calddings/ panelllings using VHB Tape

Poster Size A4 Refer design drawing 2.5eG

Emergency Signs - Photoilluminiscent Refer design drawing 2.6b-G Providing and fixing all Photoluminiscent signs in the dedicated fire escape passages of the airports as per locations given in sign schedules, made of screen printing using artworks provided and with photoluminiscent material as per technical specifications.Screen printing shall be done on self adhesive vinyl and pasted on 2mm thick powder coated white (RAL 9016) aluminium plate and fixed at location using screws. as per specification and using provided artwork including all operations from procuring the correct materials and made to sizes as specified and approved by the Engineer-in-charge. including all installation activities like marking, alignment and fixing with screws into the wall/cladding/face to the satisfaction of the Engineer-in-Charge.>>

Vinayak Infra Signs and Projects Pvt Ltd

POSHDECOR

Admire Sign and Display Pvt Ltd

STAR GLOW

CUSTOM WRAPS INDIA

SATIN NEO DIMENSIONS PVT LTD