PROVN OF GUARD ROOM AT FORT AREA, SCREEN WALL FOR TOILET NEAR SML-02, STORM WATER DRAIN AROUND BLDG NO T-46 AND T-47, WORKING PANTRY AND TOILET AT BLDG NO 04 OFFR MESS AND CONSTR OF ALUMINIUM PARTITION IN GS BRANCH AFI I BLDG AT NAGPUR.

Amount

Excavation in trenches not exc 1.5m in depth and 1.5m in width and getting out in soft/ loose soil complete all as specified and directed.

M&L for providing cement concrete 1:4:8 type D2 (Using 40mm graded stone aggregate) as in foundation, mass concrete and fillings complete all as specified and directed.

M&L for form work to sides of concrete in foundations, footing base, base of columns, side and soffits of plinth beam and similar work complete all as specified and directed.

M&L for providing RCC 1:1.5:3 type A-1 (nominal mix) as in footing, foundation, beams, plinth beams, base for columns and mass concrete etc complete all as specified and directed.

M&L for form work to sides of columns and similar work complete all as specified and directed.

M&L for providing RCC 1:1.5:3 type A-1 (nominal mix) as in columns and pillars etc complete all as specified and directed.

M&L for form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels and similar work complete all as specified and directed.

M&L for providing RCC 1:1.5:3 type A-1 (nominal mix) as in beams, cantilevers, bressummers, lintels over 1.5m span concrete etc complete all as specified and directed.

M&L for form work to chullah hoods, chajjas, troughs and similar items including edges and similar work complete all as specified and directed.

M&L for providing RCC 1:1.5:3 type A-1 (nominal mix) as in chajja etc complete all as specified and directed.

M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

M&L for form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exc 20cm wide complete all as specified and directed.

M&L for providing 25mm thick (measured solid), precast cement concrete (1:2:4) type B0 (using 12.5mm graded stone aggeregate) as in louvers and jallies, including all mouldings, set in cement mortar 1:4 complete all as specified and directed.

M&L for providing RCC 1:1 1/2:3 type A-1 (nominal mix) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the likes complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending and binding with mild steel (anneal) wire not less than 0.90mm dia complete all as specified and directed.

All as per item No 15 above but 8mm dia complete all as specified and directed.

All as per item No 15 above but 8 to 10mm dia as in stirrups, spacers and binders complete all as specified and directed.

M&L for brick work with fly ash brick, old size, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and as directed.

All as per item No 18 above but half brick wall in CM 1:4 complete all as specified and as directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 mixed with WPC finished even and smooth without using extra cement complete all as specified and directed. Note:- WPC will be measured & paid separately.

Supply only liquid water proofing compound of approved quality complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper over a coat of cement primer complete all as specified and directed.

M&L for preparation of new undecorated plastered surfaces of wall and applying three coats of white wash etc complete all as specified and as directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment etc complete all as specified and directed.

M&L for mild steel work in tubular/square hollow trusses, purlins, rafter and tubular posts including special shaped washers etc, complete using ERW or induction butt welded tubes conforming to IS 1161-1979 Grade St-240 with one shop coat of zinc chromate primer paint etc complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for 4mm thick non asbestos fibre cement building boards, designer, of size 595 mm x 595 mm, fixed or laid/inserted to timber/ GI /aluminium frame work as in ceiling, flat or sloping complete all as specified and as directed. Note:- Snap grid will be measured and paid for separately. Make:- Oceanic brand (ISI marked) of Everest / Visaka.

S&F for GI powder coated framework for seamless ceiling of size 600mm x 600mm comprising of hot deep galvanized steel perimeter angle 0.43mm thick of size 24mm x 24mm fixed to surrouding wall using nylon sleeves and screws at 450mm centre to centre, main runner Tee section 0.4mm thick with height 38mm and cross Tee 0.3mm thick with height 28mm suspended from soffits at approx 1200mm centre to centre with GI cleat and steel expansion fastness including GI wire 4mm dia suspender complete all as specified and directed. Note:- (i) Ceiling board shall be measured & paid separately. (ii) The grid system shall be as per specification of make as specified and directed.

M&L for moorum/red bajri filling in floors or pavings, laid in layers not exc 15cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for hardcore of gauge not exc 63mm, deposited, spread and levelled in layers not exc 15cm thick, watered and rammed to a true surface for plinth protection/ path complete all as specified and directed.

M&L for 75mm thick cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base to floors, finished even complete all as specified and directed.

M&L for providing 25mm thick cement concrete 1:2:4 type B1 (Using 20mm graded stone aggregate), as in sub base in floor/paving etc complete all as specified and directed.

M&L for coloured non skid ceramic tiles 6 to 7mm thick (square or rectangular) area of each tile exceeding 0.18 sqm but not exc 0.38 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or colored cement to match the shade of tiles over 15mm cement screed bed in cement mortar 1:4 complete all as specified and directed.

All as per item No 36 above but as in risers, steps, skirting, dado and pillar including 10mm thick backing coat in CM 1:3 etc complete all as specified and directed.

M&L for coloured glazed ceramic tiles 300x450x6 to 7mm thick, in floors etc set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles including rendering 10mm thick in CM 1:4 complete all as specified and directed.

M&L for 75mm thick cement concrete type C-2, 1:3:6 (using 40mm graded stone aggregate) finishing cement concrete surface even and smooth without using extra cement as in plinth protection complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in cills, steps, seismic and other similar bands, plinth courses, lacing courses parapets and railing upto 60cm height, copings, kneelers, bed plates, hold fasts block, filling on pressed steel door frame etc complete all as specified and directed.

M&L for mild steel angle iron as in framed chowkats for door shutters cut to length including necessary welding and making holes for fixing butt hinges and fixing 10mm dia as tie bar confirming to Fe-410-O etc complete all as specified and directed.

S&F flush shutters, solid core construction with block board core and plywood face panels, commercial type, on both sides 30mm thickness complete all as specified and directed.

S&F 30mm thick 2nd class hard wood factory made glazed and skeleton shutter open rebated and prepared to receive glass, gauze etc divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers edges of framing plain chamferred or rounded, fitted with cut and mitred beads for securing glass, gauge etc for windows, ventilators etc, provided with stiles and rails as specified in SSR part-I, Sec-08, Clause 8.24(b), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, fixing in opening as per specification complete all as specified and directed.

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 4mm thick moulded laminated PVC Sheet on the front face & 4mm plain colour PVC sheet on back face, with wood free EPS, fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F 100mm long medium weight, cold rolled, mild steel butt hinges complete all as specified and directed.

S&F extruded aluminium alloy handles, fabricated type, anodised of 125mm long complete all as specified and directed.

S&F aluminium anodised barrel tower bolts of extruded section and fixed of 100mm long complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

M&L for steel windows with top hung shutters including hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

M&L for 4.0 mm thick frosted sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each panes complete all as specified and directed.

M&L for preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F towel rail 20mm dia of chromium plated, fixed with and including chromium plated brass screws and wooden/ plastic cleats complete all as specified and directed.

S&F vitreous china squatting pan 'Orissa' pattern, size 580x440mm, white, with integral foot rest (excluding flushing cistern and flush pipe complete all as specified and directed.

M&L for 100mm dia cast iron 'S' / 'P' trap, including jointing with solvent cement complete all as specified and directed.

S&F in repairs PVC valve less syphonic action type flushing cistern of 10 litres capacity, low levels white/ colored with inlet ball valve flushing cistern, float and handle including brackets and PVC flush pipe 32mm dia and PVC connection pipes complete all as specified and directed.

S&F flushing pipe of polyethylene of low or high density or PVC, 32mm dia, for low level cistern complete all as specified and directed.

S&F vitreous china urinals, half stall type, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flushing cistern with brackets, flush pipe, grating and union for discharge pipe complete all as specified and directed.

S&F 15mm bore CP urinal spreader for urinals complete all as specified and directed.

S&F PVC connection 15mm size, 450mm long with PTMT nuts both side complete all as specified and directed.

S&F rotational moulded polyethlene water storage tanks (cylindrical vertical with closed top) of 1000 ltrs capacity hoisted and fixed in position complete all as specified and directed.

S&F ball brass valve high pressure with polythene float and fly nut, screwed for iron pipe of size 20mm dia complete all as specified and directed.

S&F 15mm bore bib taps, fancy type, chromium plated, with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F 15mm bore stop cock / angle cock, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed.

S&F 15mm GI tubing 'medium grade' with all fitting and fixtures to wall / ceiling or laid in floor complete all as specified and directed.

All as per item No 65 but 20mm bore complete all as specified and directed.

S&F 100mm dia cast iron soil, waste and vent sand cast pipes in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) pipes of 75mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

M&L for 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F CP grating of size 100mm dia complete all as specified and directed.

S&F slotted cast iron vent cowl of 100 mm size complete all as specified and directed.

S&F in repairs chromium plated shower rose with or without swivel joints of 125mm dia including fixing to 15mm bore of pipe complete all as specified and directed.

M&L for providing cement concrete 1:2:4 type B2 (using 40mm graded stone aggregate) as in foundation, mass concrete and fillings complete all as specified and directed.

M&L for loose filling with aggregate of gauge 80 to 150mm of broken bricks complete all as specified and directed.

M&L for cement concrete 1:2:4 type B1 (using 20mm graded stone aggragate) as in surface channels and drains complete all as specified and directed.

M&L for precast cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in landings, cover slabs (for manholes etc) chullah hoods, chajjas, mangers, shelves and similar articles with plain faces and set in CM 1:6 complete all as specified and directed. Note:- Reinforcement shall be measured and paid separately.

M&L for laying 150mm dia salt glazed stone ware drain pipes of grade ‘A’ and jointed in cement mortar and tested on completion complete all as specified and directed.

M&L for concrete bed to drain pipe including packing under and haunching against the side of pipe after they are laid and tested of 150mm bore complete all as specified and directed.

Surface excavation not exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed.

M&L for 50mm thick cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in base of floor/ hardstanding and finished the surface even and smooth without using extra cement etc complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in hard/dense soil complete all as specified and directed.

Removing excavated material (soil) not exc 50m and deposited where directed at a level not exc 1.5m above the strating point complete all as specified and directed.

S&F powder coated anodised aluminium partion aluminum section weighing 0.55kg/sqm including neccesary joining cleats, glazing clips, rubber neoprene packing, handle 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified and directed.

M&L for 12mm thick prelaminated particle board, exterior grade, prelaminated both sides with decorative choice laminations, fixed with rubber neoprene packing complete all as specified and directed.

Cutting holes in brick walls/ stone wall built exc one brick but not exc two brick in cement mortar or in cement lime mortar for inserting holdfasts/ support for cabin and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 complete all as specified and directed.

S&F framed work such as grills, gratings, bracket etc, with ends of bars shouldered and/or riveted, or forged into spikes; and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed.

M&L for 18/19mm thick prelaminated particle board, exterior grade, prelaminated both sides with decorative choice laminations, fixed with rubber neoprene packing complete all as specified and directed.

S&F for steel concealed hinge for cabinet complete all as specified and directed.

S&F 75mm stainless steel handles for cabinet complete all as specified and directed.

S&F for brass, 2 leaver locks, drawer, grade I, size 50mm complete all as specified and directed.

Excavation in trenches not exc 1.50 m wide and not exc 1.50 m deep and getting out in hard/ dense soil for foundation etc for shaft, wells, manholes etc not exc 10 sqm on plan and not exc 1.5 m in depth and getting out complete all as specified and directed.

Excavation in trenches, not exceeding 1.5 mtrs wide and not exceeding 1.5 mtrs in depth for foundation etc not exceeding 10 Sqm area on plan and getting out in Hard rock by chiseling complete all as specified and directed.

M&L for formwork flat surface rough finished surface of concrete to face of drain walls, retaining walls, parapet and similar work including attached pillasters buttresses etc vertical or to batter complete all as specified and directed.

M&L for rendering 5mm thick on concrete surfaces in CM 1:3 finished even and smooth without using extra cement for surfaces and additional thickness is provided as floating / setting coat of area drain complete all as specified and directed.

M&L for RCC 1:1½:3 type A1 (using 20mm graded stone aggregate) as in drain side wall, beams and columns, in roofs landing in shelves and the likes complete all as specified and directed.

M&L providing precast reinforced cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in cover slab for manholes, landing etc setting in cement mortar 1:6 complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top and bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, panelling of plain colour PVC sheet to be filled in the M.S.frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, & fixing in the frame at site as per specification and drawing complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube S&F in opening as per specification & drawing complete all as specified and directed.

S&F 300mm long aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed.

S&F 150mm long aluminium alloy anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F 100mm long butt hinges cast brass with mild steel hinges pin, bright polished and fixed, type B-11 etc complete all as specified and directed.

S&F in repair pillar taps, swan neck 15mm dia cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F push tap any colour high pressure of PTMT screwed for iron pipe and fixed, (Minimum weight 15mm-47gms / 20mm- 75gms) complete all as specified and directed.

S&F urinal spreader of PTMT any colour for fixing with 15mm dia pipe (Minimum weight 60gms) complete all as specified and directed.

S&F grating doom 100mm dia with waste hole of PTMT (Minimum weight 25gms) complete all as specified and directed.

S&F towel ring of fixed with and including chromium plated brass screws Etc complete all as specified and directed.

S&F viterous china wash basin, white flat back size 63x 450mm counter sunk oval type fixed in granite, excluding taps, waste chain and plug and porcelain stopper including cutting for and pinning in ends of brackets and waste pipe and fixing of pillar tap, PVC connection waste pipe, coupling etc complete all as specified and directed.

M&L preparation of new plastered surfaces and applying three coats of white wash on wall complete all as specified and directed.

M&L for machine cut pre polished granite stone slab, 15 to 18mm of any shade as approved by GE as in flooring 20mm thick including 20mm thick cement mortar 1:6 screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc if required, to be carried out at site after fixing of pre polished granite stone in position to match the surface as required complete all as specified and directed.

M&L for machine cut cudappa stone slab 18-20 mm thick over cement screed bed of 15mm thick in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for rounding to edges of stone slabs one edge as in steps, cooking platforms etc and similar situations complete all as specified and directed.

M&L for complete removal of existing treatment of walls and applying two coats of oil bound distemper over a coat of birla white wall care putty complete all as specified and directed.

M&L for colored glazed ceramic tiles in vertical surface 300x 450x 6-7mm thick set and jointed in neat cement slurry and pointed in white or colored cement to match the shade of tiles including rendering 10mm thick in cement mortar 1:3 complete all as specified and directed.

M&L for vitrified ceramic tiles 10mm thick (square or rectangular) polished, light shade area of each tile not exceeding 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or colored cement to match over 15mm cement screed bed in cement mortar 1:4 complete all as specified and directed.

M&L for coloured non skid ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tiles over and including 15mm thick screed bed of cement mortar (1:6) etc complete all as specified and directed.

M&L for 15mm dia GI tubing 'medium grade' with all fitting and fixed complete to wall and ceiling or laid in floor complete all as specified and directed.

M&L for 20mm dia GI tubing 'medium grade' with all fitting and fixed complete to wall and ceiling or laid in floor complete all as specified and directed.

S&F aluminium (powder coated) door with frame, sliding type (aluminium section weighing 0.55kg/m) and necessary fittings such as mortise lock (godrej) handles and glazing with 5.5mm thick coloured glass for top half portion and 5mm thick bakelite sheet for bottom half with necessary fixing arrangements complete all as specified and directed.

S&F sheet glass ordinary quality, 5.5mm thick and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and directed.

S&F sink with drainage board made of stainless steel, 1mm thick, for kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilevers brackets and connecting union to pipe overall size 915x330x160mm complete all as specified and directed.

S&F anodised aluminium powder coated frame for doors, windows, ventilators with one or more rebates including jointing cleats for fixing etc complete all as specified and directed.

M&L for 12mm thick plywood grade BWR type BB fixed with screws to timber frame work complete all as specified and directed.

S&F mild steel, medium weight, cold rolled, 75mm size, butt hinges complete all as specified and directed.

S&F for 125mm aluminium handles cast type anodised complete all as specified and directed.

M&L for 0.9mm plain laminate type 1 of surface finish, colour and pattern as approved, fixed with adhesive complete all as specified and directed.

M&L for 1st class plain fillets sectional area not exc 3 sqm square rectangle or triangular in section secured with nails or brads complete all as specified and directed.

M&L for french polishing on surfaces of any descripton width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats complete all as specified and directed.

Point wiring 1100 volt grade single core FRLSH PVC insulated & unsheathed cable with multistranded copper conductor 1.50 sqmm drawn in electrical grade PVC conduit not less than 20mm dia with IS 9537 (Part-III) 1983 marking medium grade concealed in wall/ceilling including FRLSH PVC insulated unsheathed earth wire with copper conductor of size 1.50 sqmm pressed steel terminal modular boxes sunk on wall for mounting of switches switch sockets fan regulator etc including modular white cover plate suitable for mounting modular switches, sockets, fan regulator etc complete all as specified and making good to distrubed surfaces for one light point controlled by one, one way switch. Note: Cost of cable provided from sub main DB to respective switch board in rooms shall be included in the quoted point wiring rate. All switches, fan, sockets, cieling roses and holders shall be connected to common earth dolly.

All as per item No 130 above but one ceiling /exhaust/ wall mounted fan point controlled by one switch and regulator complete all as specified and directed.

All as per item No 130 above but one 3 pin 5 amp socket out point on the same board with other switches complete all as specified and directed.

All as per item No 130 above but one 3 pin 5 amp socket out point on independent board complete all as specified and directed.

All as per item No 130 above but wiring with 4.0 sqmm multi stranded cable and earth wire with copper conductor of size 4.0 sqmm for 15 amps power point complete all as specified and directed.

M&L for sub main wiring with 2 single core FRLSH PVC insulated, unsheathed, multistranded, copper conductor wie 4.0 sqmm, 1100 V grade including and 4.0 sqmm PVC insulated, multistranded unsheathed copper wire, green in colour, as earthing lead drawn through and including PVC conduit not less than 20mm dia marking medium grade concealed in wall/ ceilling and accessories complete all as specified and directed. Note:- Two runs of 4 Sqmm cable & one run of 4 sqmm cable as earth continuity conductor and one run of PVC casing capping shall be measured & paid as one unit/one rm.

S&F switch, modular type, single pole, one way, 6 amp, 1 module, 250 volts AC suitable for modular switch boxes complete all as specified and directed.

S&F socket, modular type, single pole, one way, 6 amp, 2 module, 2/3 pin, 250 volts AC suitable for modular switch boxes complete all as specified and directed.

S&F switch, modular type, single pole, one way, 6/16 amp, 3 pin, 250 volts AC suitable for modular switch boxes complete all as specified and directed.

S&F socket, modular type, single pole, one way, 6/16 amp, 2/3 pin, 2 module, 250 volts AC suitable for modular switch boxes complete all as specified and directed.

S&F ceiling rose, surface type, three terminal, 5 amps complete all as specified and directed.

S&F 0-4 step 2 module, modular type electronic regulators for ceiling fan 1200/1400 mm sweep, 240 volts, 120 watts single pole complete all as specified and directed.

S&F highly durable surface mounted 18/20 watts LED batten/surface constructed of fire retardant engineering grade extruded plastic and decorative end cap complete with tube rod, driver including 3 core 1.0 sqmm copper conductor cable for connection and accessories complete all as specified and directed. Make:- Cat No LCTL-18-CDL of CG/ BLTRU 20W NW VIVA of Bajaj/ BN150W LED20S-6500 PSE OD GR of Philips.

S&F highly durable surface mounted 09 /10 watts LED batten, constructed of fire retardant engineering grade extruded plastic and decorative end cap complete with tube rod, driver including 3 core 1.0 sqmm copper conductor cable for connection and accessories complete all as specified and directed. Make:- Philips Slim Line 9W/ LCTL-09-CDL of CG/ SLW BT 10W of Surya.

S&F LED light fitting 10W bulk head luminaries with lamp holders etc complete with all accessories and including connecting upto with twin core twisted flexible cable of suitable size of 230V, 50Hz complete all as specified and directed. Make:- Bajaj Cat Part no BIBWP 10W / LBHN 10 WW of CG.

S&F ceiling fan 1200 mm sweep, single phase 230V AC 50Hz, BEE 5 Star rated complete including 3 core cable from ceiling rose to fan connector complete all as specified and directed.

S&F sheet metal enclosure, single pole & neutral for 240 volts, 4 way with 200 Amp rated bus bar flush /surface mounting double door complete all as specified and directed.

S&F MCB single pole, 240 volt, 6 to 32 amps, 10 KA complete all as specified and directed.

S&F MCB, single pole and neutral, 240 volt, 6 to32 amps, 10 KA complete all as specified and directed.

S&F exhaust fan, single phase, 225mm sweep, PVC body type with bolts, nuts, washers and connected electrically complete all as specified and as directed.

M&L for earthing complete with galvanised steet earth plate electrode 600 x 600 x 6mm thick burried directly in ground (earth plate not less than 2.25mtr deep below normal ground level) with top edge of the plate not less then 1.50 mtr below the normal ground level connected to galvanised earth lead wire 4.00mm dia by means of bolts nuts check nuts & washer of galvanised iron or steel all as shown in electrical plate No 5 connected to earthing test point all as specified and testing on completion including the material and labour for:- (a) Excavation and earth work or drilling hole for electrode in any type of soil. (b) PCC pit in cement concrete 1:2:4 type B-1. (c) Pre cast RCC cover with suitable handle 40mm thick in PCC 1:2:4 reinforced with welded steel wire fabric weighting not less than 1.87 Kg/sqmm. (d) Funnel with watering pipe of GI 20mm nominal bore medium grade and Aluminium lugs etc all as specified. (e) 15mm nominal bore meduim grade GI protection pipe upto 7.50 metre long for protection of earthing lead. (f) Reguisite quantity of charcoal and common salt. (g) Connection to earthing test point and testing on completion.

M/s DS Khekde

Bidder Name

M/s DS Khekde

Khushi Construction