SPECIAL REPAIR TO SINGLE OFFRS ACCN OF EAGLE COMPLEX BUILDING NO. P-7 and P-8 AT BB CANTT, SRINAGAR

Amount

Taking down shutters area exc 1 sqm and n. exc 2 sqm each complete all as specified and directed.

Taking down frame with shutters (without taking off shutters from frame) area n.exc 1.5 sqm each complete all as specified and directed.

Taking down frame with shutters (without taking off shutters from frame) area exc 1.5 sqm but n.exc 4 sqm each complete all as specified and directed.

S&F for 2nd class hard-wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F 35mm thick 2nd class hard wood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F 30mm thick 2nd class hardwood factory made glazed and skeleton door/window shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and as directed.

S&F galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples etc complete all as specified and directed.

Dismantling wall and ceiling & floor boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

M&L for 12mm thick Block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work including required teak wood lipping complete all as specified and directed.

S&F 1.5mm thick Decorative laminate type 1 of surface finish, colour and pattern including necessary fillets/ cornices as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.

M&L for 2nd class hardwood 20mm thick boarding, plane one side with butt joints and fixed with nails complete all as specified and as directed.

M&L for 2nd class hardwood 25mm thick boarding, as in flooring, plane one side with butt joints and fixed with nails complete all as specified and as directed.

M&L for 12mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work complete all as specified and as directed.

M&L for 2mm thick Linoleum sheet, plain coloured, laid dry in floors including stretching, cutting and sealed down with an approved adhesive complete all as specified and as directed.

S&F stainless steel butt hinges medium weight 100 mm size etc complete all as specified and directed.

Ditto all as per serial item No 16 described here-in-before but 75mm size.

S&F 150 mm size extruded aluminium handles fabricated type, anodised complete all as specified and directed.

S&F 150 mm size aluminium anodised barrel tower bolts of extruded sections complete all as specified and directed.

S&F 250 mm aluminium alloy, anodised, sliding door bolt with hasp, staple & fixing clips of sheet, cast or extruded section & fixing bolts & sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

S&F 100 mm size aluminium anodised hasp and staple, safety type, with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F 30 mm width of flap (when open), Continuous (piano) hinges, mild steel, bright finish or electro-galvanised complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles etc complete all as specified and directed.

M&L for brickwork with old size sub class 'B' bricks straight or curved on plan exc 6m mean radius and built in CM 1:6 etc complete all as specified and directed.

Taking down cement plaster of any description, on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for rendering 10mm thick in CM (1:6) on brick work or concrete surfaces finished even and fair without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM (1:4) on brick work or concrete surfaces finished even and fair without using extra cement complete all as specified and directed.

M&L for raking out joints/pointing to random rubble masonry uncoursed or brought up to courses on old walls built in cement mortar complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

M&L for framed brackets of angles or tees with web and flanges, tubular pipes cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc. n exc 10 kg each brackets, conforming to Fe. 290. Gde-E-165 complete all as specified and directed.

M&L for coloured non-skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with shade of tile laid over and including 15mm thick screed bed in CM 1:6, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) etc complete all specified and directed.

M&L for coloured glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with shade of tile fixed over and including 10mm thick backing coat in CM 1:4, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) etc complete all as specified and directed.

Hacking out old broken glass (any thickness size quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes including necessary bends, fittings etc single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

Ditto all as per serial item No 35 described here-in-before but 75mm bore.

S&F Steel water tubing medium grade galvanised with all fitting and fixed complete to wall and ceiling or laid in floors of 15mm bore including taking up or down steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Ditto all as per serial item No 37 described here-in-before but 20 mm bore pipe

Lagging to pipes internal dia 15mm used in internal water supply or plumbing all round with, 40min thick bonded mineral wool preformed ‘SNAP ON ’pipe sections of density 144Kg/cum conforming to IS9842 including chicken mesh wire netting 25 gauge, 20mm mesh and POP on top surace including removing old legging where required, complete all as specified and directed

Ditto all as per serial item No 39 described here-in-before but internal dia 20mm

S&F in repairs 15mm bore Brass CP mixer (WHB/wall) for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repair cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) of 75 mm dia etc complete all as specified and directed.

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern), white excluding (fixing bolts, flushing cistern and flush pipe) including PVC seat cover (closed pattern), connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, health facet etc complete all as specified and directed.

S&F in repairs 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including Flush pipe of polyethylene of low or high density or PVC 32 mm dia complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm etc complete all as specified and directed.

S&F in repairs 125mm brass chromium plated shower roses including fixing to steel pipe etc complete all as specified and directed.

S&F in repairs vitreous china wash basin of size 550x400mm (flat back or angle back type) including padestal or erecting stand and 32mm waste fittings, brass, chromium plated for basins, waste pipe etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and waste pipe etc complete all as specified and directed.

S&F in repairs toilet paper holder, vitreous China, box type, white, fixed to walls with chromium plated (CP) brass screwsc complete all as specified and directed.

S&F in repairs Soap dish, vitreous China white, approximate size 160x 160x90mm fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repairs Sheet glass shelf assembly /corner shelf consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail 20mm dia complete all as specified and directed.

S&F Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) all as specified and directed.

S&F in repairs 15mm bore Bib taps, chromium plated, fancy type, screwed down, screwed for iron pipe or for brass ferrule etc complete all as specified and directed.

S&F in repairs 15mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S&F in repairs 15mm bore stop valves or angle valve, fancy type chromium plated, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions etc complete all as specified and directed.

S&F 500 litres capacity rotational moulded polye-thylene water storage tanks (cylindrical vertical with closed top) triple layered hoisted and fixed in position including brass float valve all as specified in SSR Part I including dismantling PVC water tanks exc 250 litres and not exc 500 litres capacity etc complete all as specified and directed.

Demolition of plain cement concrete (un-reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) etc complete all as specified and directed.

M&L for rubber moulded chequered cement concrete tiles with grey cement and pigments 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over and including 20 mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed.

M&L for 75mm thick PCC (1:4:8), type D2 (using 40mm graded crushed stone aggregates) as in sub base or floors etc. complete all as specified and as directed.

Dismantling of plain or corrugated steel sheeting, any gauge thickness, including nanital or similar pattern roof covering complete all as specified and directed.

S&F 0.63 mm thick galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with coach screws and washers, in roof, wall etc with grade of zinc coating 275 complete all as specified and as directed.

S&F 0.63 mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 fixed with coach screws and washers complete all as specified and as directed.

Dismantling of timber scantlings 40 sqcm and over in section, in any position unframed work complete all as specified and as directed.

M&L for wrought Second class hard-wood in scantlings frame work complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old painted wooden surfaces of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over any surfaces complete all specified and directed.

M&L for preparation of old painted steel surfaces of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls, apply two coats of oil bound distemper over a coat of suitable primer complete all specified and directed.

M&L for preparation of old plastered surfaces of walls, apply two coats of oil bound distemper complete all specified and directed.

M&L for applying 2 mm thick wall care white putty after complete removal of existing treatment from old plastered surfaces and to obtain smooth/even finish using sand paper complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description over 10 cm width or girth and apply two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F in repairs 100 mm bore, spun pipes, Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors, walls including necessary bends, fittings, stack clamp etc complete all as specified and directed.

Ditto all as per serial item No 74 described here-in-before but 75mm bore.

S&F in repairs stainless steel kitchen plate rack of size 750mm x 750mm x 250mm, 600mm x 900mm x 250mm fixed to wall with stainless steel screws etc complete all as specified and directed.

S&F in repairs Harrison rails (curtain rails) , mild steel, chromium plated, 20mm bore with fixing brackets, stops, rollers etc complete all as specified and directed.

Taking down carefully existing old burnt out/unserviceable copper/aluminium point wiring any type (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing old materials from site and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M&L for making point wiring system with single runs of PVC insulated FRLS wire, 1100 volt grade with multistranded copper conductor wire of size 1.5 Sqmm (Nominal area) any type any lengthy drawn through in PVC casing capping / PVC conduit of suitable size along with its all connected fittings accessories including providing of modular type/size of pressed steel terminal sunken boxes or PVC flush type box and dully fixed it concealed in wall or surface on wall (type of wiring fixing/laying work to be carried out at site as per decided & direction of EIC) and providing alongwith modular type back and face top covered plate frame for housing / mounting of switches sockets, regulators etc and also using /drawn of 1.5 sqmm PVC insulated FRLS wire 1100 Volt grade with multistranded copper conductor wire used as a continuous earth wire which is connected with terminated the box to ceiling rose / fitting complete and including making good to all disturbed surfaces of wall/ceiling, wall panel and floor area of wiring system and to match the existing surface of wall/floor/ceiling etc. for the following complete all as specified and directed :-

One light/fan point controlled by one, one way switch.

One 3/5 pin socket outlet, 5 Amps on same board controlled by one, one way switch

One 3/5 pin socket outlet point, 5 Amps on independent board controlled by one, one way switch

One bell point controlled by one, one way bell switch.

Ditto all as per serial item No. 78.00 described here-in-before but using single runs of PVC insulated FRLS wire, 1100volt grade with multistranded copper conductor wire of size 2.5 Sqmm (Nominal area) power point wiring system with controlled by one way switch fixed on independent board and also providing of 2.5 sqmm PVC insulated FRLS wire, 1100 Volt grade (ISI Marked) with multistranded copper conductor wire used as continuous earth wire complete all as specified and directed.

S&F modular type switch 5/6 Amps 220 Volts for one module complete as specified and directed.

S&F modular type socket 5/6 Amps 220 Volts, 3/5 pin two module complete as specified and directed.

S&F modular type switch 15/16 Amps 220 Volts for one module complete as specified and directed.

S&F modular type socket 15/16 Amps 220 Volts, 5/6 pin two module complete as specified and directed.

S&F Modular bell push 6A one module, complete all as specified and directed.

S&F Buzzer, ding dong, AC, 230 V, Single pole (ISI marked) completed all as specified and directed.

S&F ceiling rose three terminals type made out of polycarbonate, isolated body complete all as specified and directed.

S&F one/two modular type step type electronic fan regulator with hum free step alongwith speed control knob of capacity 120 watt complete all as specified and as directed.

S&F LED tube light fitting 1 x 20W/ 22W, 220V AC decorative box type with electronic driver, holder including LED tube light with having energy efficient including providing of suitable type of flat flexible cable for electric connection complete all as specified and directed.

S&F LED tube light fitting with high output diffuser 2' long, 9/10W, 220V AC decorative type with electronic driver, holder including LED lamp with having energy efficient including providing of suitable type of flat flexible cable for electric connection complete all as specified and directed.

Supply and fixing surface mounted LED decorative type angle adjustable sport light / bed side study lamp light fitting with lamp in matt finish for premium aesthetics with based of suitable rating capacity 7Watt LED complete light fitting set all as per existing fitting type/ size of sample /model and make and required fitting use in both warm/white type colour complete light fitting and including providing of suitable type of flat flexible two/three core cable and making electric connection, complete all as specified and directed.

S&F surface mounted LED bulk head luminaries light fitting of rated capacity 10W including LED lamp & driver, out door type with dust and water proof, energy efficient for ready to use and required in both warm/white type colour fixture complete including dully fixed on bldg wall surface including providing of suitable type of flat flexible two/three core cable and making electric connection complete all as specified and directed.

S&F environmental friendly LED street light fitting of rated capacity 35W 230 volt AC with having LED driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics, out door type, having IP 65/66 protection made out of high pressure die cast hosing with heat resistant glass complete light fitting set including providing of suitable dia or as recommended by manufacturer GI pipe light grade bracket and it to match/setting the new fitting fixture hole attachment system of suitable bracket length make to shape / bend including duly fixed alongwith existing pole /bldg wall/ roof with the help of 02 Nos of MS fixing clamp alongwith nut bolt and including providing of suitable type of flat flexible two/three core cable and making electric connection complete all as specified and directed.

S&F angular/ batten type shape lamp holder with PVC/ Polycarbonate insulated body, alongwith brass adaptor and back plate for housing of bulb complete all as specified and directed.

S&F ventilating exhaust fan made out of sturdy engineering plastic body complete with louvers and shutter, 250mm sweep suitable to work on 230 Volts 50 Hz, 1200 RPM, copper winding including making of suitable type /size of hole on wall and fixing compete with nut, bolt etc including taking down old exhaust fan and deposited to E/M store all as specified and directed.

S&F ceiling fan 1200mm sweep min air delivery 210CFM with BEE norms 5 star rating of single phase 220 volt AC alongwith blade and down rod and MS fan hook duly fixed in roof area alongwith flat flexible copper wire for electrical connection including taking down old ceiling fan and deposited to E/M store complete all as specified and directed.

S&F electric water heater storage type steel body with inner copper tank and heating element upto 2KW of storage capacity 25 ltr, BEE 5 star rating and providing all connecting accessories such as safety valve, thermostat, NRV, connection pieces including taking down old water heater and deposited to E/M store complete all as specified and directed.

S&F in replacement sheet metal enclosure box duly powder coated & framing work with locking system and having double door fixing arrangement system suitable of rating of size/type for vertical type distribution board vertical loadline type of rating VTPN 4 way type 415volt, 3 phase AC supply holding system with IP protection rating with ISI marked and having fitted neutral and earth link bus bar and mounting base channel and blanking plates suitable for holding of main MCCB as incomer and outgoing MCB complete system alongwith providing and mounting in side of DB box 01 Nos MCCB TPN 160 Amps with breaking capacity 25 KA having adjustable setting & adjustable magnetic type and also providing of 8 Nos MCB SP 63Amps 10 KA 'C' curve same as per make of distribution board and also making all necessary electrical connection and dully fixed surface on wall or concealed in wall with the help of cutting chases to wall for fixing of DB and making good the disturbed wall surface complete all as specified and as directed.

S&F in replacement sheet metal enclosure box duly powder coated & framing work with locking system and having double door fixing arrangement system suitable of rating of size/type of distribution board of rating SPN 8 way type 220 volt AC supply system with IP-43 protection rating and having neutral and earth link bus bar mounting base channel for holding MCBs incomer and outgoing complete set and also making all necessary electrical connection and dully fixed surface on wall or concealed in wall with the help of cutting chases to wall for fixing of DB and making good the disturbed wall surface complete all as specified and as directed.

S&F MCB SPN 40 to 63 Amps, 230 Volts, 50 Hz AC supply suitable for 'C' series, 10 KA breaking capacity complete all as specified and directed.

S&F MCB SP 10 to 32 Amps, 240 Volts, 50 Hz AC supply suitable for 'C' series, 10 KA breaking capacity complete all as specified and directed.

M&L for sub main wiring system with two runs PVC insulated FRLS wire, 1100 volt grade with multistranded copper conductor wire of size 2x10 Sqmm and one run of 1x10 Sqmm (Nominal area) (ISI Marked) as in earth wire any type any length drawn through in heavy duty ISI marked PVC Casing capping / PVC conduit of suitable size along with its all fittings and connected accessories and duly fixed concealed on wall or surface on wall including taking down old sub main wiring and making good the disturbed wall surface complete all as specified and as directed. Note:- 3 runs of 10 sqmm wire and one run of PVC casing capping/conduit shall be measured and 1.0 RM.

M&L for earthing, complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (Earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.5 mtr below normal ground level connecting to the galvanised iron earth lead wire of 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron and earth strip protected by provision of GI light grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded of stone aggregate with XPM (weight not less than 4 Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and with 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate common salt and charcoal filling test point made out of 40mm/6mm flat iron with fixing arrangement funnel wire mesh and earth work in hard dense soil returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs all as per electrical plate No 03 of SSR-2009 Part-I and connecting to earth test point complete all as specified and directed.

S&F rigid non metallic PVC conduit/ casing capping of size 20/25 mm bore heavy duty with all fitting laid in trenches/ wall including providing clamping arrangement for holding of pipe on wall in proper size of clamps, nut bolt and washer etc complete all as specified and directed.

S&F earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire complete all as specified and directed.

M&L for taking down carefully existing ceiling fan/ exhaust fan and geyser any type and capacity and after removing fan blade and body parts and cleaning all dust particles and filling cavities with filler material, oiling, greasing including painting fan with blade complete body by applying two coats of synthetic enamel paint on any type of fan with blade and geyser frame and assemble the same alongwith all connecting & fixing accessories such as rubber reel, nut, bolt, washer, lock pin, clamp etc and complete body system as per existing type of colour and after painting work assemble the same along with connecting fixing accessories like rubber rell, nut, bolt, washer, locking pin, clamp etc and hanging and refixing the same in position with providing nut, bolt and washer etc and making electric connection complete all as specified and directed.

Notes :- An amount of Rs 77,966.00 on account of Credit Schedule for Schedule 'A' Part-II shall be deducted from total quoted amount of BOQ to arrive at the contract sum.

M/S D N Enterprises (BID ID -3351740)

CLASSIC CONSTRUCTIONS (BID ID -3349768)

M/S NEW IQBAL ENTERPRISES (BID ID -3352860)

M/S PARVEZ AHMAD LONE (BID ID -3352635)

M/S AIJAZ ENTERPRISES (BID ID -3352345)

RISING SUN ENGG WORKS (BID ID -3351903)

Alishan Builders (BID ID -3353100)

KHUSHBU TRADERS (BID ID -3352871)