Repair/Renovation of Bungalows/Kothi at Ghulami Bagh Jammu. CNO-581 NP

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed

Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge: 1:4:8 or richer mix (i/c equivalent design mix)

Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge: in cement mortar

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead. For thickness of tiles 10 mm to 25 mm

Providing and laying in position Cement Concrete of specified grade excluding the cost of centring and shuttering, all work ypto plinth level (1:4:8) 1 cement:4 coarse sand:8 graded stone aggreagate 40mm nominal size (crusher)

Providing and laying in position Cement Concrete of specified grade excluding the cost of centring and shuttering, all work ypto plinth level (1:3:6) 1 cement:3 coarse sand:6 graded stone aggreagate 20mm nominal size (crusher)

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form work for: Foundations, footings, bases for columns

Centering and shuttering including strutting, propping etc. and removal of form work for:Suspended floors, roofs, landings, balconies and access platforms

Edges of slabs and breaks in floors and walls

steel reinforcement for R.C.C. work including straightening,cutting,bending ,placing in position and binding all complete upto plinth level

Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead.

15mm Cement plaster of mix: 1 : 6 ( 1 cement : 6 fine sand)

6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand)

Brick work with common burnt clay F.P.S (non modular) bricks of class designation 75 in cement mortar 1:6(1 cement : 6 fine sand). Foundation and plinth.

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 1mm thick

2 mm thick

Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm)

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade, one or more coats on old work

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.Two or more coats on new work

taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 meters lead : of area of 3sqm.and below

providing &fixing IS Imarked M S pressed butt hinges bright finished with neceesary screws complete:100x58x1.9mm

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately):Second class deodar wood

Providing and fixing aluminum die cast body tubular type universal hydraulic door closer (having brand logo with IS: 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete :

providing &fixing of ply 19mm thick ply including cutting wasteage fevicol carriage etc complete item of superior conforming BWP 710

providing &fixing of ply 6mm thick ply including cutting wasteage fevicol carriage etc complete item of superior conforming BWP 710

providing and fixing of 1.00mm thick sunmica including cutting ,wastage,fevicols nails etc.complete

Providing and fixing of sliding channel 20"

Providing and fixing of ss handle 8"

Providing and fixing of auto hinges

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete 11.52.2 Size of tile 600x600 mm

Providing and laying matt finished vitrified tile of specified size having water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in outdoor floors such as footpath, court yard multi models etc., laid on 20mm thick base of cement mortar 1:4 (1cement: 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as direction of Engineer-in-Charge. 300x300x9.8 mm

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. In colour such as White, Ivory, Grey, Fume Red Brown

Providing and fixing special quality ss finished/ alloy Door handle lock locks of approved quality including necessary screws etc. complete

Providing and fixing SS handle 12"

Mason 2ND class

carpenter 2nd class for dismentling of cupboard

labour

engaging trolley for shifting of mulba from site to beyond the muncipality limit including loading and unloading

Engaging welder including the cost of welding set and helper for mislaneous welding works at site

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

. Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing of water proof flush door 34 mm with 1.0mm th. Sunmica (green,century or equivalent make) on both sides incl. lipping, paining, all accessories like hinges, tower bolts ,lock(harrison , godrej) handle complete

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-incharge. (Note: -Butt hinges and necessary screws shall be paid separately).Second class Deodar- wood : 30mm thick

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. 12 mm thick Marine plywood conforming to IS: 710

4 mm thick glass pane (weighing not less than 10 kg/sqm)

providing and fixing glazed shutter for doors,windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S pressed butt hinges finished of required size with necessary screws 30 mm second class deodar wood

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge :Second class deodar wood : 30mm thick

Extra for using stainless steel grade 304 wire gauge with wire of dia. 0.5 mm instead of Galvanized M.S. Wire gauge with wire of dia. 0.63 mm for doors, windows and clerestory windows with necessary screws: (shutter area to be measured

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete 300x10 mm

Renewing glass panes, with wooden fillets wherever necessary : 14.7.1 Float glass panes of thickness 4.0 mm (weight not less than 10kg/sqm)

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete Fixed to openings / wooden frames with rawl plugs screws etc.

providing and fixing of PVC panelling on walls /false ceiling 8 to 10 mm thick inc, all fitting and fixtures complete (wall affair or any equvl. Make.

providing and fixing of wallpaper of approved quality and specification as per EIC

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

providing and laying water proofing treatment on roofs /walls by applying cement slurry mixed with water proofing cement compound consisting of applying (a)after surface preparation ,frst layer of cement @0.488 kg/sqm mixed with water proofing cement compound @0.253kg/sqm(b)laying second layer of fibre glass cloth when the first layer is still green .Overlps of joints of fiber cloth should not be less than 10cm.(c)third layer of 1.5mm thickness consisting of slurry of cement @1.289kg/sqm mixed with water proofing cement compound @0.670kg/sqmand coarse sand @1.289kg/sqm. this will be allowed to air cure for 4 hours following by water curing for 48 hours .the entire treatment will be upto 30cm on parapet wall and tucked into groove in parapet all around

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete

providing &fixing of PVC Pipes for drainage ,severage,rain water flow pipe etc including labour &material costs complete job in all heights(LMR) 4' dia

Providing and fixing of CP Brass short nose bib cock of approved make / specification as directed by E.I.C (Cera, Jaquar, Hindware or equivalent )

Providing and fixing of CP Brass long nose bib cock of approved make / specification as directed by E.I.C (Cera, Jaquar, Hindware or equivalent )

Providing and fixing of CP Brass angle valve of approved make / specification as directed by E.I.C (Cera, Jaquar, Hindware or equivalent )

Providing and fixing of CP Brass single towel rail 600 mm of approved make / specification as directed by E.I.C (Cera, Jaquar, Hindware or equivalent )

Providing and fixing of CP Brass sink/wall mixer of approved make / specification as directed by E.I.C (Cera, Jaquar, Hindware or equivalent )

Providing and fixing of CP Brass C. P gratings 4" of approved make / specification as directed by E.I.C (Cera, Jaquar, Hindware or equivalent )

Providing and fixing of CP Brass soap dish holder of approved make / specification as directed by E.I.C (Cera, Jaquar, Hindware or equivalent )

Providing and fixing of CP Brass towel ring square of approved make / specification as directed by E.I.C , Jaquar, Hindware or equivalent )

Providing and fixing of CP Brass hand shower of approved make / specification as directed by E.I.C (Cera, Jaquar, Hindware or equivalent )

Providing and fixing of P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete: 18.28.1 Semi rigid pipe 40 mm

Providing and fixing of CP Brass toilet roll holder with SS flap

Providing and fixing soap dispenser with glass bottle

Providing and fixing of towel rack 600mm long without lower hangersbut 3 hooks

Providing and fixing of glass shelf with bracket

Providing and fixing of floor mounted/WALL HANGING, white vitreous single piece double water closet of approved brand(JAQUAR,HINDWARE) and make shape size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system incl all fittings and fixtures complete work

Providing and fixing white viterous china flat back wash basin wash basin with pedestal including, 15mm C.P brass centr hole basin mixer, 32mm C.P brass waste coupling of standard pattern, including all fittings and fixtures of make jaquar, cera or eq as directed by EIC

Providing and fixing of aluminium partitio/ door/window incl shutters, frame,glass,,mosquito mesh fittings complete

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour or shade 8.2.2.2 (Area of slab over 0.5 sqm)

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour or shade 8.2.2.1 (Area of slab upto 0.5 sqm)

Painting wood work with deluxe multi surface paint of required shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.75litre/10sqm of approved brand and manufactur

Providing and fixing of laminate finish vanity incl wastecoupling etc complete job

providing and fixing CP brass shower rose with arm 15mm or 20mm inlet 100mm dia

Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with ordinary cement mortar, including disposal of rubbish, all complete as per the direction of Engineer-In-Charge.

Providing and fixing 10mm thick toughened glass fixed/sliding door inc. all fitings and fixtures complete

Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

providing and fixing ss pipe curtain rods ,with nickel plated brackets including fittings 25mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge. Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc. 15mm outer dia pipes

20mm outer dia pipes

25mm outer dia pipes

Providing and fixing of ss multipurpose basket 20"x15"x4"

Providing and fixing of ss multipurpose basket 20"x15"x6"

Providing and fixing of ss multipurpose basket 20"x15"x8"

Providing and fixing of ss multipurpose basket 20"x15"x12"

Providing and fixing of ss masala pullout 15"x18"x18"

Providing and fixing of ss thali basket 15"x20"x18"

Providing and fixing of ss utensil rack of approved quality and size as directed by EIC

Providing and fixing 4mm thickness APP Superthermoly STP sheet (polyester-based sheet with black finishing, including two coats of silver-colored paint) with hot torch treatment over RCC/cemented surfaces shall be done as follows: (i) Apply Shalitex STP primer for bitumen membrane at 0.40 liters per square meter. (ii) Lay the 4mm thickness APP Superthermoly STP sheet (polyester-based sheet with black finishing, manufacturer density at 25°C of 0.87-0.89 kg/liter) over the primer-coated layer using a butane torch and seal all longitudinal and transverse joints to prepare the surface completely. (iii) Cut a 1-inch deep groove above the roof surface on the parapet wall and seal the edge of the APP Superthermoly STP polyester sheet into the groove with polymer-modified mortar. (iv) In case of low-height parapets, terminate the APP Superthermoly STP polyester sheet over the parapet. (v) For overlapping joints, rub the polyethylene side of the membrane with a wire brush, apply Shali Bond APP over the rubbed area, allow it to become tacky, and fix the bituminous side of the APP Superthermoly STP polyester sheet using hot application. (vi) Ensure an overlap of 75mm for longitudinal joints and 100mm for transverse joints. The vital physical and chemical parameters of the membrane shall be as follows: softening point not less than 150°C; cold flexibility up to 0°C as per ASTM standards; joint strength at 23°C as 350 N/5cm in the longitudinal direction and 300 N/5cm in the transverse direction; tear strength of 60 N in the longitudinal direction and 80 N in the transverse direction. The roll weight for a 4mm thick sheet (1 meter x 10 meters) shall be 40 kg. The laying of the membrane must be carried out by a certified applicator (certificate to be attached). A single coat of aluminum paint shall be applied on top to complete the job as per the direction of the Engineer-in-Charge (E.I.C.).

Providing and fixing of kitchen chimney having suction 1350 cmh , filterless auto clean,motion sensor incl. cuttinh hole in wall for outlet and making good the surface with painting complete make-faber,elica,hindware,glen

Providing and fixing of gas stove electrically/battery operated Easy to clean, toughened black glass top extra strong pan support stainless steel drip tray revolving inlet nozzle Fuel efficient brass burner extra strong pan support stainless steel drip tray Cooktop with 4 burner including making hole in shelf and wall for making provision of fixing of gas cylinder outside kitchen incl. cost of pipe and other required fittings complete job make-faber,elica,hindware,glen,

French spirit polishing, Two or more coats on new works including a coat of wood filler

Providing and fixing ply wood 4mm thick one side decorative veneer conforming to IS: 1328(type 1), for plain lining/cladding with necessary screws, including priming coat on unexposed surface with. Decorative veneer facings of approved manufactures

Please Enable Macros to View BoQ information