Construction of Centre of Excellence building for WRD at WRD Complex Gogal Margao under NHP in the state of Goa

Amount

Clearing grass and removal of rubbish upto a distance of 50 m outside the periphery of the area

Earthwork in Excavation in all types of strata comprising any of the material such as soil, silt, sand, clay, gravels, moorum of all varities shingles, pebbles all types of conglomerates laterite rock, soft rock, ordinary rock, disintegrated rock, fissured /shattered decomposed rock, or weathered rock and all such other materials as described under appendix to these specifications either in full or in parts as the case may be, adopting any approved method or methods as may be convenient or permitted inclusive of chiseling wedging etc. but blasting prohibited etc.. in all conditions such as dry, moist, saturated submerged foul conditions etc. including pumping and bailing out water and disposl of the excavated earth with all lifts and all lead etc. complete as directed by Engineer in charge

Refilling the pipeline/foundation trenches plinth sides, foundation etc. with available excavated earth in layers not exceeding 20 cm depth consolidating each layer ramming and watering lead upto 50 M and all lifts and disposal of surplus earth as directed by Engineer in Charge.

Disposal of surplus earth excavated material from the site with a lead of 10 kms including all loading & unloading charges (a) by tipper ruck including loading unloading and stacking .contractor should arrange land for dispose up these material at his own cost with lead upto 10km.

Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete.

Half brick masonry usign fly ash bricks in cement mortar 1:3 (1 cement : 3 coarse sand ) with bricks of class designation 40 kgs / cm2. (b) Above plinth upto floor V level 200 x 95 x 95

Laterite masonry in neatly dressed stones of size as specified in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and basement.

Laterite masonry in neatly dressed stones for 23 cms thick masonry walls in c.m. 1 : 4 (1 cement : 4 coarse sand in foundation upto plinth level . Extra for laterite masonry in all sizes in superstructure from floor I level upto floor V level.

Ground floor Level

First Floor Level

Second floor level

Third floor Level

Fourth floor (Roof Level)

Making plinth protection 50mm thick of Cement Concrete 1:3:6 (1cement: 3 Coarse Sand: 6 graded stone aggregate 20mm nominal size) over 75mm bed of dry laterite aggregate 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering, shuttering and finishing in:(a)All works upto plinth level

Providing and laying in position (1:11/2:3) Reinforced cement conrete excluding the cost of centering, shuttering, finishing and reinfrocement (1 cement: 1½ coarse sand:3 graded stone agg 20mm nominal size) (b) In beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases upto floor five level

Providing and laying in position ready mixed concrete (RMC) with usage of Ordinary Portland Cement manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead upto 10kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C., from the transit mixer to the site of laying, excluding the cost of centering, shuttering, finishing and reinforcement including the cost of admixtures in recommended porportions as per IS : 9103 to accelerate/retard setting of concrete, improve workability without imparing strength and durability with a condition that cement content to be used 410kg per cu.m.for M30 grade of concrete and No GBBS to be used as per the directions of the engineer-in-charge. All works upto floor V level

Centering & shuttering including Strutting, Propping & removal of forms for :

Foundations, Footings, Bases for columns

Vertical surfaces such as retaining walls, return walls, Partitions, walls (any thickness) including attached Pilasters, Buttresses, Plinth and string courses, Fillets and the like

Columns, Piers, Pillars, Abutments, Posts and struts (square rectangle polygon in plan)

Sides and Soffits of beams, Beam Haunchings, Cantilever, Girders, bressumers and Lintels plinth beams not exceeding 1m in depth

Staircases (except spiral staircases) excluding landing

Suspended floors, roofs landings, shelves & their supports

Vertical or horizontal fins individually forming box louvers or projected bands

Centering & shuttering including Strutting, Propping & removal of forms for sloping or battering surface (slabs, beams, louvers, etc) including folded plates (i) Where inclination to the horizontal does not exceed 30° requiring shuttering on the underside only

Providing corrosion resistant steel CRS-50 bars of (SAIL, TATA, VIZAG, JSW Steel Ltd. make or equivalent) (Confirming to IS 1786 if 1985) for RCC work including bending, binding & placing in position in all the floors along with factory made precaste concrete cover blocks of specified s izes whose compressive strengthis not less than that of surrounding concrete in the structural member .

Providing fusion bonded epoxy to reinforcing bars as per IS:13620-1993 specification for a thickness of 175 +- microns including testing of coating at plant, extra cost for careful handling using PVC coating, binding wires instead of G.I. wires, touching up the material supplied, repair work etc. complete as per detailed specifications MORT&H section 1600 etc. complete and as per the Directionof Engineer in charge.(Steel to be paid separately)

Providing flat iron hold fast 40 cm including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedded in cement concrete block 30 x 10 x 15 cm 1:3:6 mix (1 cement: 3 coarse sand: 6 stone aggregate 20 mm nominal size. (b) 40 x 3 mm flat iron hold fast, 15 cm long

Providing woodwork in frames of doors, windows, clerestory windows trusses & other frames wrought framed and fixed in positon. [c] First class matti wood

UPVC ONLY DOOR FRAME:- Providing & fixing Upvc Door Frame Yashashri make or equivalent made out of Upvc extruded multi cavity frame of 60 mm x 60mm x 2mm wall thickness. Frame is reinforced with G.I. Channel & welded in corners with Average weight 0.80 kg per running mtr. These frames are tested by using BS 2782 & DIN 53459 test methods.ge

32 MM DOOR SHUTTER:- Providing & fixing 32mm door shutter Yashashri make or equivalent, made by using 31mm x 150 mm x 1.5mm upvc multi-cavity section having Toung & Groove jointing method and boarder having 35mm x 30mm x multi- cavity section. The corners are joined by inserting polymetric corners & hardware used for fixing the door shutter is stainless steel hinges & S. S. handle & S.S. tower bolt. The average weight of 32mm door shutter is 6.30 kg per sq mtr. These Upvc sections are tested by using BS 2782 & DIN 53459 test methods.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type (BWP), core of block board construction with frame of 1 st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on Front face of shutters with combination of light shade and dark shade laminate providing 3.5mmx3.5mm grooves on front face and single dark shade laminate on rear face as shown in the drawing and as directed by the Engineer in charge

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type (BWP), core of block board construction with frame of 1 st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on Front face of shutters with combination of light shade and dark shade laminate providing 3.5mmx3.5mm grooves on front face and single dark shade laminate on rear face and providing and fixing vision panel with 6mm plain glass rectangular of size 200mm x 700mm fixing shutter with Stainless steel butt hinges (heavy weight) 100x60x2.5 mm and Stainless steel screws 40 mm as specified in the approved drawings and as directed by the Engineer in charge as shown in the drawing and as directed by the Engineer in charge

Providing and fixing ISI marked flush double leaf door shutters conforming to IS : 2202 (Part I) decorative type (BWP), core of block board construction with frame of 1 st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on Front face of shutters with combination of light shade and dark shade laminate providing 3.5mmx3.5mm grooves on front face and single dark shade laminate on rear face and providing and fixing vision panel with 6mm plain glass rectangular of size 200mm x 700mm on both panels , fixing shutter with Stainless steel butt hinges (heavy weight) 100x60x2.5 mm and Stainless steel screws 40 mm complete, design of shutter as specified in the approved drawings and as directed by the Engineer in charge

Supplying and fitting in position 12 mm toughened glass for external wall / partition wall including single leaf or double leaf door including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete all necessary fittings of Stainless steel ozone make or equivalent including door stoper,chrome plated 12" long handles on both sides of door , lock and designing the glass etching pattern as per the approved drawings, complete and as directed by the Engineer in Charge

Providing & fixing bright finished brass 100 mm. rim latch & lock & a pair of knob, with necessary screws etc. complete (Indian make of approved quality).

Providing and fixing Stainless steel D type handles with necessary screws etc complete a) L 300mm/325mm x 22 to 25mm dia

Providing & fixing chromium plated brass tower bolts (barrel type) with necessary screws complete. (a)250 x 10 mm

Providing and fixing 150 mm. bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete.

Providing and fixing brass hydraulic door closer of make Everest universal 68 or equivalent with necessary screws and fittings complete

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) (Square Hollow Section (SHS) IS4923 /Rectangular Hollow Section (RHS) IS4923/ Circular Hollow Section (CHS) IS1161 closed Structural Steel of approved make (Min Yeild Stress 310 Mpa)) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

Providing and fixing in position S.S. hand rail in main stair case, and landing as per approved design shown in the drawing including bending handrail pipe to proper shape in curves with specials, etc. complete.

Providing and fixing in position S.S. hand rail with S.S. frame work of 304 grade fitted with toughened glass 10mm thick, top pipe of 2" diameter and 16Gauge fiting balusters 1.5"x 1.5" of 16 guage at 90cm centre to centre spacing in landing etc. as per approved design shown in the drawing including bending handrail pipe to proper shape in curves with specials, with toughened glass fitting including all the necessary S.S. screws and other fittings of approved make , drilling and finishing etc. complete. as directed by the Engineer in Charge.

Providing and fixing aluminium shutters including all transportation, scaffolding and handling: windows with three sliding shutters using 27 mm series shutters section with 5mm plain glass fitting providing maruthi make locks and handles and the whole assembly is powder coated with off white/ brown shade and fitiing in position by s.s screws etc. the gaps if any between the frame and wall to be filled with silicon for making water tight complete as per approved drawings and as directed by the Engineer-in-charge

Supply and installation of Aluminium VentilatorsThe frame should be made with 2.5" x1.50" aluminium frame shade and Z shaped louvers of Figured glass glass should be fixed to the supporting frame with aluminium cleats, GI screws, etc complete. The whole assembly is powder coated with off white/ brown shade the gaps if any between the frame and wall to be filled with silicon for making water tight complete as directed by the Engineer in Charge

Providing and fixing prefabricated compound gate of G.I. pipes 40 – 50 mm dia (medium) with 12mm M.S. square bars of G.I. pipes grill work as per drawing including providing & fixing locking arrangements, pintals, hold fast embedded in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 granitic or basaltic aggreate 20mm nominal size) including applying priming coat with ready mixed red lead paint and painting 2 or more coats with superior ready mixed paint of approved brand and manufacture in all shades as per direction complete.

Providing and fixing M.S. grill of required pattern in wooden frames of Windows etc. with M.S. flats square or round bars with round headed bolts and nuts or by screws. (A) Plain grill

Providing and fixing curtain rods of 1.25 mm thick anodized aluminium plates brackets in pelment instead of wooden curtain rods of 25 mm diameter and brackets (actual length of rods to be measured). (a) 12 mm dia.

Providing and fixing aluminium box channels powder coated sections of size 10cm x 4 cm of 18 Guage af approved make and shade including all transportation, scaffolding and handling with necessary stainless steel screw fittings / welding etc. complete as per the approved drawings and as per the direction of the Engineer-in-charge

Kotah stone slab flooring over 20 mm (average) thick base laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) (a) 20 mm thick.

Kotah stone slab flooring over 25 mm thick in risers of steps, skirtings, dado & pillars laid on 12mm (average) thick cement mortor 1:3 (1 cement : 3 coarse sand) & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete.

Providing and laying in design & pattern factory made PVC RUBBER MOULDED Interlocking Cement Concrete paver blocks of M35/M40 strength, thickness & size/shape, made by table vibratory method using Rubber mould, laid in required colour & pattern over 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with river/manufactured sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. complete as per manufacturer’s specifications & direction of Engineer. (e) 80 mm thick -coloured other than Grey (M40 grade)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, area of slab over 0.50 sqm (a) Jet Black

Providing and fixing Granite stone slabs (mirror polished) 18mm thick in risers of steps, skirting, dado and pillars laid on cement paste and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete

(A)Jet black

(B)Cherry Red/ Ruby red

Providing & Fixing granite stone of jet black polish for Tread 18 mm fbk. In single piece with rounded off nosing antiskid grooves 3nos. laid on and including 20 mm (average) thick bed of cement slurry including pointing with pigmented cement slurry in match the shade of slab, cleaning etc. as directed by Engineer-in-charge

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/Granite/Cuddapah stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing vitrified matt finished (600x600) and 10mm thick tiles in floor, treads of steps, landing on 25mm thick bed of cement mortar 1:3 and jointed with cement slurry complete.

Providing and laying vitrified antibacterial tiles for dado (Johnson, Somany, Kajaria ) conforming to IS:15622 (thickness to be specified by the manufacture of approved make in two colour combination(Plain and highlighter) of size 30cm x 60cmx0.90 finished as per approved design and colour by the Engineer-in-charge on 12 mm thick cement plaster 1 : 3 ( 1 cement : 3 coarse sand ) and jointing with grey cement slurry @3.3kg per sq.m including pointing in white cement mixed with pigment of matching shade , curing and cleaning, etc. where they are required to be cut (only area of portion of cut tiles to be measured). complete.

Providing and fixing Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps and dados, jointing with grey cement slurry @3.3 kg per sqm, including pointing/grouting in white cement mixed with pigment of matching shade complete. (B)60X60CM IN LIGHT SHADE

Providing and and laying scratch resistant floor tiles in different sizes of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make in colours and shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigment etc., complete (B)600 x 600 mm light Shades

Providing and fixing vitrified matt finished (800x800)mm and 9.5mm thick tiles ,(NITCO, Johnson, Somany, Kajaria ) conforming to IS:15622 in floor, landing on 25mm thick bed of cement mortar 1:3 and jointed with cement slurry @3.3kg per sq.m including pointing in white cement mixed with pigment of matching shade , curing and cleaning, etc. where they are required to be cut (only area of portion of cut tiles to be measured). complete. shade in each room as approved and directed by the Engineer in charge

Providing and fixing vitrified matt finished (800x800) and 9.5mm thick tiles ,(Nitco, Johnson, Somany, Kajaria ) conforming to IS:15622 in skirting, of size 60cm x 60cm finished as per approved design and colour by the Engineer-in-charge on 12 mm thick cement plaster 1 : 3 ( 1 cement : 3 coarse sand ) and jointing with grey cement slurry @3.3kg per sq.m including pointing in white cement mixed with pigment of matching shade , curing and cleaning, etc. where they are required to be cut (only area of portion of cut tiles to be measured). complete.

Providing 25 mm thick cuddapah slabs machine cut and polished on either side in partitions including making necessary grooves in the wall and fixing with cement mortar, complete as directed by the engineer-in-charge

Providing 20mm thick marble slab to urinal partitions with cement complete

Supplying and erection / fabriction the Lexan brand or equivalent multiwall polycarbonate sheet to the roof frame including all the necessary fittings of approved brand and make complete with leak proof testing as per the approved drawing and as directed by the Engineer in charge

a) 10mm thick bronze multiwall Polycarbonate shade

b) 10 mm thick clear multiwall Polycarbonate shade

Supplying and erection / fabriction the Lexan brand or equivalent multiwall polycarbonate sheet 3mm thick bronze shade to the roof frame including all the necessary fittings of approved brand and make complete with leak proof testing as per the approved drawing and as directed by the Engineer in charge

Providing and fixing colour coated galvulium roofing sheets of 0.5mm thickness including all the accessories (TATA Make or equivalent) but excluding the cost of purlins, rafters, trusses, flashings etc. complete as per the directions of the Engineer in charge.

Add for providing & fixing Flashings -[Corners, Ridges, valleys, gable end & Trims] (Girth upto 610mm) including all the accessories complete as per the directions of the Engineer in charge.

Waterproofing of sunken slabs, toilet blocks, terraces on slabs under brickbats, roofs, watertanks. Cleaning the surface and filling cracks (if any) , applying EPCO ACR wherever necessary, Providing and moistening the surface with water to render it saturated. Mix Cement and Monobond WF in the ratio of 1.25 kg to 1 by weight and stir continuously . Apply minimum 2 coats with an interval of 12 hours minimum between the coats .Fix fiber mesh while the first coat is still tacky. Cure with sprinkling of water 3-4 times a day. incl. cost of scaffolding transport etc. as per dir of EIC. All the chemicals will be of Krishna Conchem Products Pvt Ltd. or Equivalent.

12mm cement plaster 1:4 (1 cement : 4 fine sand)

6mm cement plaster to ceiling 1: 4 (1 cement : 4 fine sand)

Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Neat Cement punning

18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge.

Applying one coat of distemper primer of approved brand and manufacture on wall surface.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :1 Two or more coats on new work

Painting three or more coats with acryllic exterior paint of approved brand and manufacture (Such as Dulex/ Asian Paints/ Sherwin Willians) including applying one coat of cement primer and one coat of surface treatment etc. complete.

Painting 2 coats with oil type wood preservative of approved brand & manufacture on new work.

Applying priming coat with ready mixed primer of approved brand and manufacture on wood work complete.

Painting two or more coats (excluding priming coat) with superior quality ready mixed paint for wood work of approved brand & manufacture in all shades on new work to give an even shade.

Providing and applying 2 coats of Anti-corrosive, chemically resistant coal tar extended epoxy coating system for below & above waterline application (Normal Wet & Underwater Application) (EPCO-2020-TX) having an adhesion of minimum 3.0 N/mm2 (ASTM-D-4541) and a DFT of 300-350 microns in 2 coats and having excellent chemical resistance against acids, alkalies and salts. Incl. cost of transport etc. as per dir of EIC. All the chemicals will be of Krishna Conchem Products Pvt. Ltd. or Equivalent.

Applying priming coat with ready mixed primer of approved brand and manufacture on steel work.

Painting two or more coats (excluding priming coat) with superior quality ready mixed paint for steel work of approved brand & manufacture in all shades on new work to give an even shade.

Earthwork in surface excavation not exceeding 30 cm in depth (but exceeding 1.5 m in width as well as 10 sq.m on plan) including disposal of excavated earth beyond work site for all leads lift disposed earth to be leveled and neatly dressed in ordinary soil.

Supplying and stacking of good earth at site including royalty and carriage upto 1 km. (earth measured in stacks will be reduced by 20% for payment).

Spreading of sludge, dung manure or/and good earth in required thickness (cost of sludge, dung manure or/and good earth to be paid separately).

Grassing with “doob” grass including watering and maintenance of the lawn for 30 days or more till the grass forms of thick lawn free from weeds and fit for moving, including supplying good earth if needed. (Cost of “doob” grass not included ) 3) In rows 5 cm apart in either direction

Providing and fixing M.S flat iron tree guard 60cm dia & 2 m high above ground level, formed of 4 nos. 25 x 6mm and 8 nos. 25 x 3mm vertical M.S. flat iron rings in two halves, bolted together with 8mm dia and 30 mm long bolts inluding painting two coats with paint of approved brand and manufacture over a coat of priming, complete in all respects.

Filling mixture of earth & sludge or manure in the desired proportion in trenches flooding with water and leveling (cost of supplying earth and sludge of manure and mixing excluded).

A). Forxtail palm 3 m ht & 0.075 m atleast Girth

B). Pongamia pinnata 2.4 m ht & 0.075 m atleast Girth

C.) filiciun decipiens 3m ht & 0.075 m atleast Girth

D.) Caryota urens 3 m ht & 0.075 m atleast Girth

Supplying of laterite stone soling of size 150-200 mm size and murrum having P.I. Value not more than 6 and laying including packing with smaller stones and consolidation with power road roller including spreading, watering and consolidation of binding material etc.(Measurements shall be considered on finished item) .

Retro- reflectorised Traffic signs (Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 2012 made of high intensity Grade sheeting using ASTM sheeting "C' type XI micro prismatic retro reflective material vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing)etc complete as per MORT &H Specifications Fifth Edition. A 10 years warranty for Retro Reflective Sheeting from the original sheeting manufacturer & a certified copy of three years outdoor exposure report from an independent test lab for the product offered shall be submitted by the contractor. (b)60 cm equilateral triangle

Providing & fixing of facility information sign board of size 600mmx800mm rectangle made out of retro reflective sheeting conforming to Type XI standards of ASTM D4956-09 & as per IRC-67: 2012 specifications, fully covered over 4mm thick ACP/2mm thick Al supported with back support frame of 35x35x5 mm mild steel angle. Board Shall be fixed to a vertical post of 75x75x6mm mild steel angle of 3.6 mtr height and firmly fixed to the ground by means of properly designed foundation with M20 grade cement concrete 45 cm X 45 cm X 60 cm etc, 60 cm below ground level. 10 years warranty & a certified copy of three years outdoor exposure report from an independent lab as per IRC 67-2012 for Type XI retro reflective sheeting shall be submitted by the contractor.

Proving and fixing white vitreous china water closet squatting pan (Indian type w.c. pan) size 580 mm with 100 mm sand cast iron P. or S trap 3/6 litres P.V.C. dual Automatic flushing cistern (of Jaquar make or equivalent of approved make) with all fittings, rack bolts 32 mm diameter P.V.C telescopic flush pipe and clamps 25mm P.V.C. over flow pipe with specialsconfirming to IS 7231, and mosquito proof coupling of approved municipal design and nylon. chain and pull complete, cutting and making good the walls ad floors where required

Providing and fixing white vitreous china water closet squating (European type w.c. pan) with white plastic seat and lid, C.P. brass hinges and rubber buffers P. or S trap 3/6 litres P.V.C. dual Automatic flushing cistern (of Jaquar make or equivalent of approved make) with all fittings, rack bolts 32 mm diameter P.V.C telescopic flush pipe and clamps 25mm P.V.C. over flow pipe with specialsconfirming to IS 7231, and mosquito proof coupling of approved municipal design and nylon. chain and pull complete, cutting and making good the walls ad floors where required.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 x 260 x 350 mm and 340 x 430 x 265 mm sizes respectively with pvc automatic flushing cistern with fittings, R.S. or C.I. brackets, standard size galvanised steel flush pipe and spreaders with brass unions & G.I. clamps complete, including painting of cister and fittings, cutting and making good the walls and floors where required.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 including cutting of stone and making good the walls wherever required : Kitchen sink with drain board with coupling & all accessories complete with choke stop strainer, Plain type having flat borders for correct sandwithing between the plaform top and bottom slabs complete (a) Overall size 1040mmx510mm (41"x20") bowl size 460mmx410mmx200mm (18"x 16"x 8") depth 200 mm. Glossy. 1.0mm thk,

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/Granite/Cuddapah stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing & fixing (4’) 100 mm sand cast iron grating for gully floor or nahni trap

Providing & fixing c.p. brass towel rail complete with C.P. brass brackets fixed to wooden cleats with C. P. brass screws b)600 x 20 mm size

Providing and fixing toilet paper holder :(a) C.P. brass

Providing & fixing liquid soap container with C. P. brass lid and brackets fixed to wooden cleats with C. P. brass screws (b) Plastic container

Providing & fixing G.I. pipes complete with G.I. fittings including trenching & re-filling etc. (external work). (b) 20 mm nominal bore

ProMaking connection to individual 15mm/20mm/25mm G.I/ OD Blue PVC pipeline with existing distribution line of any diameter with saddle piece / and necessary pipe and specials required suitable to the distribution line with road cutting trenching refilling the same including the cost of labour and accessories etc. complete. as per the direction of engineer -in- charge.

Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately) :80 mm dia nominal bore

Providing and fixing brass full way valve (heavy) duty with wheel of approved quality :

(b) 20 mm nominal bore

(d) 32 mm nominal bore

[e] 40 mm nominal bore

Providing and fixing ball valve (brass) of approved quality : (B) Low pressure with copper. floats : (3)25 mm nominal bore .

Providing and fixing non-return valve of approved quality :

Providing and fixing P.V.C. connection pipe with brass unions 15 mm nominal bore: [c] 45 cm (18”) length .

Providing and fixing C.P. brass shower rose with 15 or 20 mm. Inlet: (b)150 mm diameter.

Providing and placing on terrace roof of floor two (1st flor roof single piece rotational moulded polythene water storage tank having I S I mark and conforming to I S 12701; 1996. [C]1000 lit. capacity. Extra for placing polythene tank on roof of floor three (2nd floor roof) [c]1000 lit. capacity

Constructing brick masonry manhole or inspection chamber with second class bricks in cement mortar 1:5 (1 cement :5 fine sand) R.C.C. top slab with 1:2:4 mix (1 cement: 2 coarse sand ;4 graded stone aggregate 20mm nominal size foundation concrete 1:2:4 mix (1 cement ;2 coarse sand :4 graded stone agrregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cemetn and making channels in cement concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) neatly finished complete as per standard design.

Inside size 90 x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455 x610mm internal dimensions total weight of cover ad frame to be not less than 38 kg. (weight of cover 23 kg. )

Inside size 1.2m x 90 cm and 90cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter total weight of cover and frame to be not less than 116 kg. (weight of cover 58 kg).

Inside size 60 x 60cm and 60cm deep including C.I. cover with frame (light duty) 455x610mm internal diameter total weight of cover and frame to be not less than 38 kg. (weight of cover 23 kg).

Providing M.S. footrests including fixing in manholes with 20 x 20 x 10 cm cement concrete block 1:3:6 (1 cement :3 coarse sand :6 graded stone aggregate 20 mm nominal size) as per standard design :[a] With 20 x 20 mm square or round bar

Supplying and fixing C.I. cover without frame for manholes:

Making chases upto 7.5x7.5 cm in walls including making good after housing G.I. pipe etc.

Constructing soak pit 1.20m x 1.20m x1.20m filled with laterite stone aggregate 125 to 180 mm including S.W. drain pipe 100 mm diameter and 1.2m. long complete as per standard design. :

Providing and fixing rigid PVC S.W.R. (soil, waste & rain water drainage pipes of approved including lubricant etc. complete (single/double) socketed:

110 mm dia[4"]

75 mm dia (2½")

Providing and fixing rigid PVC bend of required degree (of approved make) for S.W.R. drainage pipes of approved including lubricating.

110 mm dia

75 mm dia

Providing and fixing rigid PVC bend (approved make ) for S.W.R. pipes including lubricating etc complete bend with door :

110 mm dia

75 mm dia

Providing and fixing U.P.V.C. pipe clips (approved make ) for S.W.R. pipes :

110 mm dia

75 mm dia

Providing and fixing R.P.V.C. vent cowl:

110 mm dia

75 mm dia

Providing and fixing NICKEL chrome plated copper alloy Fancy Pillar Cock rocket type Jaquar make or equivalent. Confirming to IS 8931;1993 (a) 15mm nominal bore

Providing and fixing NICKEL chrome plated copper alloy Fancy BIB Cock Short Providing and fixing NICKEL chrome plated copper alloy Fancy long body bib cock with wall flance Jaquar make or equivalent. Confirming to IS 8931;1993 (a) 15mm nominal bore

Providing and fixing NICKEL chrome plated copper alloy Fancy concealed stop cock with sheet flance 20mm Jaquar make or equivalent. Confirming to IS 8931;1993(a) 20mm nominal bore

Providing and fixing NICKEL chrome plated copper alloy Fancy wall mixer with 3 IN 1 SYSTEM WITH 115MM long bend pipe for connection to over head shower Jaquar make or equivalent. Confirming to IS 8931;1993

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. (b)20 mm dia nominal outer dia pipes.

Providing & fixing bevelled edge mirror of superior glass (5mm thk) of approved Quality, shape & size complete with CP brass screws and washers, Cleats, CP studs etc Complete.

Providing and fixing Hand Shower (Health Faucet) with 8mm dia, ABS/brass body with double lock 1.00m long Flexible tube (Brass plated stainles steel flexible hose) and wall hook of approved quality confirming to IS standards.

Providing and fixing NICKEL chrome plated copper alloy Fancy Two Way Bib Cock with single knob and wall flange conforming to IS 8931:1993 15mm nominal bore.

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer. External work 1.SCH [blue/white]

20 mm nominal bore

25mm outer dia.

32mm outer dia.

Providing and fixing single tee of rigid PVC (approved make) for S.W.R. pipes including lubricating etc. complete, without door:

a)110 mm dia

b)75 mm dia

Providing and fixing single Tee of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, with door :

a)110 mm dia

b)75 mm dia

Providing and fixing single “Y” of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, with door :

a)110 mm dia

b)75 mm dia

Providing and fixing nahani trap of rigid PVC (approved make) for S.W.R. pipes including lubricating etc complete, without door (110 mm dia)

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 m. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. b)20 mm dia nominal outer dia pipes.

Providing and fixing of 15 Litre geyser of approved brand with all necessary fittings to the walls and making function of inlet water supply and outlet connection to the mixer and power supply as directed by the engineer incharge

Providing 8' (2.44m) high corrugated G. I. Sheet (min. thickenss 0.63mm) barricading fixed with G. I. hooks and nuts on frame made of M.S angles of minimum size 40*40*6, fixed to the vertical M.S. Channel posts with spacing not less than 3.00 meters. (average). Barricading shall be painted with signs and messages to warn people about keeping away from the construction zone. The following shall be ensured while installation: • The safety barricading should be high enough so that people (especially children) cannot climb over it. • It should be installed in a manner so that one cannot crawl underneath it. • The safety barricading should be strong enough and durable enough to withstand the elements, including high wind conditions. • Should be sturdy enough to bear normal wear and tear at the construction site and should not topple off and hurt someone. Rate shall be inclusive of cost of providing all material and fixing arrangements, including excavation, concrete and backfilling etc., removal of the complete barricading after construction work is over and rehabilitation of the site. Material of barricading shall be the property of contractor after completion the work. Barricading shall be maintained throughout the construction period.

Providing anti – termite treatment to buildings conforming to I.S.S. 6113 part II 1971 (revised) including adopting precautions for health hazards and safety measures as required therein with the cost of all materials, chemicals, plants, equipments required for the treatment and furnishing a guarantee for a minimum period of 10 years from the date of completion including eradicating any infestation of termite free of cost during the guaranty period complete. (The payment will be made on plinth of the building. ((a) Pre-construction)

Supplying and fixing of Precast RCC slabs(factory made,the factory should be ISO certified and registered under Dirctorate of Industries, Govt. of India) at site in concrete Grade of M-25 with 20 mm nominal size Granitic or basaltic aggregate, consolidated by means of mechanical platform, vibration etc. with lifting hooks of M.s. 10mm bars and PVC cups including cost of reincforcement, Certificate from manufacturer shall be produced indicating grade of concret and minimum content of steel in the product along with 5 year free replacement warranty in case of breakage complete and as directed by Engineer -in -charge (a) Size 900 x 400 x 150 mm with steel reinforcement not less than 7 kg per unit -30 T capacity.

Providing and fixing 15mm thick densified tengular edged eco friendly light weight Calcium Silicate false ceiling tiles (like Aerolite Brand or Equivalent) of approved texture Spintone/ Cosmos/ Fine Fissured or equivalent of size 595mm x 595mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanizing @ 120 grams per square metre. including both side) consisting of main "T" runner suitably spaced at joints to get required length and of size 24x38mm made from 0.33mm thick (minium) sheet, spaced 1200mm center to center, and cross "T" of size 24x28mm made of 0.33mm thick (Minimum) sheet to be inter locked at middle of the 1200x600mm panel to from grid of size on a Perimeter wall angle precoated steel of size 600x600mm, resting on periphery walls/ partitions (24x24x300mm) made of 0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm and laying 15mm thick densified edges calcium silicate ceiling tiles of approved texture light fittings, fixture, smoke detectors etc., wherever required. Main "T" runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6mm fixed to celing using with 12.5mm dia and 50mm long dash fastners, level clips of size 85x30x0.8mm, spaced at 1200mm center to center along main "T" bottom exposed with 24mm of T-section shall be pre-painted with polyester baked

paint, for all heights, as per specifications, drawings etc. complete. (As Directed by Engineer in Charge)Note: Only Calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/ opening (cut outs) having are less than 0.30 sqm. The Calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection>85% non-combustible as per B.S.476 part IV, 100% humidity resistance and also having thermal conductivity 0.043 w/m 0 KC. Hospitals, Offices and Commercial Buildings, Auditoriums and Cinema Hall, Educational Institutions, R&D Centers, Studios, Laboratories, Library, Canteen.

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.

c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium items. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

ACP Cladding of wood colour

ACP Cladding wood colour at edges and off- white colour at the edges

ACP cladding off white colour on box chajja

Providing and fixing Prince or equivalent make PVC SWR half round eaves gutter with bolts, nuts and flat iron brackets 40 x 3 mm size complete. (b) 180 mm nominal size

Providing and laying plum concrete in cement concrete 1:2: 4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggregate 40 mm nominal size) with plums not exceeding 15% of the volumne of the finished concrete of size ranging from 150 to 300 mm (but the maximum dimension not exceeding 1/3rd (one third) the least dimension of member under consideration excluding the cost of centering and shuttering::a . With granitic or basaltic stone plums in :1.Foundation and plinth

Supply and installing of wilo make monoblock pump MPMS 10HH 1HP Pump or equivalent make of approved brand like kirloskar make with required head as per the site nd as directed by the engineer incharge

Providing and laying 50mm(consolidated thickness)full grout using granitic or basaltic stone of specified grading at 6.00 cu.m. per 100 sq.m. grouting with hot bitumen straight run bitumen(or with such bituminous material of grade and type as specified by the Engineer-in-Charge)at 5.0kg. per sq. m. binding with key aggregate of granitic or basaltic stone of specified grading at 1.5 cu.m. per 100 sq.m. including Providing and laying seal coat sealing the voids in a bituminious surface laid with F.E loader with 1 Cu.m. bucket capacity to the specified levels, grade and cross fall using Type A seal coat with 0.98 kg/sqm of bitumen of grade as per MoRT&H specifications clause 513.

Semi - Dense Bituminous Concrete (Providing and laying semi dense bituminous concrete with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 % of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORT& H Specifications, Fifth Edition. (i)for Grading I ( 13 mm nominal size )

Providing and laying 20mm thick premix bituminious carpet surface by using mini hot mix plant at site with 2.7 cu.m. of stone aggregate comprising 65% of 12 mm size (passing 20 mm sieve and retained on 10 mm sieve) 35% of 10 mm size(passing 12.5 mm sieve and retained 6.8 mm) per 100 sq.mt. 53.4 kg (average) of catoinic type emulsion(or such bituminious material of grade and type as specified by the Engineer-in-charge) per cu.m. of stone aggregate including all carriages. On new road surface including tack coat of bitumen emulsion of approved quality at 2.50kg/10 sq.m . complete.

Supplying and fitting of fire extinguishers to the wall by clamps and screws complete as directed by the Engineer in charge

a) KFARQ-6-50% ABC Dry Powder MAP-50% (Stored pressure ) 4kg 3A:21B fire extinguisher IS:15683

b) KFARQ-2-CO2( High Pressure ) 2kg 21B Fire extinguisher

Steel work in single sections (SAIL, TATA. VIZAG & using electrodes of Ador or ES4B or Deh Secheron make only) including cutting, hoisting fixing in position and applying a priming coat of red lead paint.(a) In R.S. joists, channels, angles, tees

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 including cutting of stone and making good the walls wherever required. Kitchen sink without drain board. with coupling & all accessories complete with choke stop strainer, Plain type having flat borders for correct sandwithing between the plaform top and bottom slabs complete. (c) Overall size 535mmx460mm (21"x18") bowl size 460mmx380mmx200mm (18"x 15"x 8") depth 200 mm. Glossy. 1.0mm thk.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) with modular switch, modular plates, suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

(c) Group C -- with Cat A Modular Accessories

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit(heavy) of appropriate size as required

(a) 2 x 1.5 sq.mm + 1 x 1.5 sq.mm earthwire (20mm Conduit)

(b) 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earthwire (20mm Conduit)

(c) 2 x 4 sq.mm + 1 x 4 sq.mm

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/ 6 A modular switch connection painting etc. as required::(a) Cat A

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 15/16 A and 5/6 A modular socket outlet modular socket outlet and 15/16 A modular switch connection painting etc. as required:::(a) Cat A

Supply and erecting of 48 inch ( 1200mm sweep) ceiling fan, double ball bearing type, , complete with all accessories::: '(a) Cat A

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required::

Installation,earthing, testing and commissioning of ceiling fan including wiring the down rod of standard length ( upto 30 cm) with 1.5 sq .mm FRFRLS PVC insulated copper conductor single core cable etc. as required.

Supplying and fixing following way SPN sheet steel MCB distribution board 240 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator)::(g) 12 way double door Cat A

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required.

(a) SP, Cat A

Supplying and fixing following rating double pole 240 V isolator in the existing MCB DB complete with connections testing and commissioning etc as required:::'(a) 40 A, Cat A

SITC of 1 x 24 W LED luminaire of approved makes like Crompton, Havells, Philips, GE, Bajaj or equivalent

SITC of 2 x 20 W LED luminaire of approved makes like Crompton, Havells, Philips, GE, Bajaj or equivalent

SITC of 14 W surface LED luminaire of approved makes like Crompton, Havells, Philips, GE, Bajaj or equivalent

SITC of 30 W LED luminaire for area lighting of approved makes like Crompton, Havells, Philips, GE, Bajaj or equivalent

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size:::(6) 4 Core 16 sq.mm

Supply of 2 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size.

( 4 ) 2 Core 6 sq.mm

( 5 ) 2 Core 10 sq.mm

Supplying and fixing brass batten/ angle holder including connections etc as required.

Earthing with GI earth pipe 2 mts long 40 mm dia medium class with ISI mark,of approved brands, including accessories and providing masonry enclosure with CI/RCC cover having locking /lifting arrangement and watering pipe etc. with charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 2.0 mtrs(min) and disposal of excavated soil. b) Class B GI pipe, 40mm diameter as per specifications. c) Charcoal/salt as per specs ( paid seperately). d) Refilling the pit of size 1.0x1.0x 2.0 mtrs(min) with soft black soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe. g)watering arrangement(plumbing will be paid seperately):::(b) In rocky strata

Supplying and laying 25 mm x 5 mm GI strip in 40 mm dia GI pipe from earth electrode as required

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm in the existing RCC/HUME/STONEWARE Metal pipe, etc. complete as required

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required::(5) 4 x 16 Sq. mm.

Supply and making cable end terminations with compression gland and copper lugs for following sizes of PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required.

(3) 2 x 6 Sq. mm.

(4) 2 x 10 Sq. mm.

Supply, installation, testing and commissioning of electronic type three phase energy meter (KWh), 4 wire, ISI marked, in polycarbonate or sgheet steel body ( base mounting type) with counter display/LCD display, with ELT, in Class 1.0, 50 Hz, 240 V. AC duly tested by MRT along with Test Certificates, complete as required of following capacity of make L & T only.(C) 50 TO 100 A.

Supply, installation, testing and commissioning of wall mounted IP54 indoor control cubicle panel suitable for operation on three phase 4 wire 440 volts 50 HZ system. The panel should be flush front , compartmentalized to allow cable entry from top & bottom; dust and vermin proof complete with interconnections of proper size of wires bus bar wiring etc.The panel should be properly de-rusted and seven tank processed and painted with Siemens 7032 powder coated paint and constructed of 16 SWG CRCA sheets. The panel should have indicating lamp set , digital voltmeter, ammeter (VAF multifunction meter) with switches and control fuses of suitable ratings and approved makes. The panel should be mounted on suitable angle iron frame. The MCCB's and MCB's shall be of L & T , Siemens, Schneider , C & S , or Hager makes only. The panel shall be as following.

INCOMING

1) 63 Amps TP MCCB 25 KA in sealed meter compartment ..1 No

2) 40 Amps copper busbar 4 strips .....1 set

3) Provision for 3 phase meter ....1 No

4) Change over 40 Amps 4 pole ....1 No

OUTGOING

1) 40 A TP MCB .....3 Nos

2) 16 A SP MCB ....3 Nos

3) Provision for 3 Nos TP MCB's

Supply, Installation, testing and commissioning of 62.5 KVA, SILENT Diesel Generating Set with CPCB II approved acoustic enclosure comprising of : Approved make , Radiator Cooled, Diesel Engine developing 80-85 BHP at 1500 RPM, complete with standard accessories - coupled to approved make of Alternator rated at 62.5 KVA at 415 Volts, mounted on Channel Iron Base Frame complete with Fuel Tank of minimum 170 Ltrs capacity with 02 nos of 12 V DC with a static battery charger working on mains supply to keep batteries charging all times, Approved Makes of Engine and Alternator as herebelow:Engine :CUMMINS Model C62.5D5P/ KIRLOSKAR GREEN (KOEL) Model 4R810TAG1/Greaves Cotton Model GPWII-PII- 62.5 / PERKINS 1103A-33TG2 /VECV EICHER PKGVE - 62.5 Alternator: STAMFORD UC27 / KIRLOSKAR GREEN(KOEL GREEN) Model 4R810TA G1 / MECC-ALTE ECO ECP32 1S4 C / MAHINDRA POWEROL 4905GMC2-CPCB-II

Supply, Installation, testing and commissioning of 1.5 Tonnes split Air Conditioner Unit along with required length of copper piping with insulation upto 3 metres( Extra lenghth will be paid separately), necessary brakets made out of MS angles for mounting outdoor unit, stabilizer unit etc complete.

Supply, Installation, testing and commissioning of 1.8 Tonnes split Air Conditioner Unit along with required length of copper piping with insulation upto 4 metres( Extra lenghth will be paid separately), necessary brakets made out of MS angles for mounting outdoor unit, stabilizer unit etc complete.

Supplying and drawing of Cat - 6 UTP, 4 pair annealed tinned copper conductor PVC insulated, PVC sheathed, unarmoured data cable in existing surface/recessed steel/PVC conduit of appropriate size including connection, etc. complete as required.(a) Cat 6

Supplying, drawing, connecting, testing and commissioning of shielded, twin twisted and stranded single core PVC insulated ( white PVC sheathing with colour skinning) FRLS copper conductor cable in existing surface/recessed steel/PVC conduit of approprriate size including connections etc. complete as required of following size :::(a) 2 x 1.5 sq.mm

Supplying, installation and testing of suitable size modular GI box , modular plate and cover complete with RJ-45 connector(modular LAN socket TX1000/ CAT6) including concealed metal box/surface GI/PVC Box, modular plate, punching, identifying, complete as required. ::: CAT A

S.I.T.C. of recessed mounted with necessary mounting arrangements square LED fittings 36 watts of make Bajaj Cat No BCTBLR36WATNWH, Philips Cat No RC380BLED34S4000G3PSDOD or Wipro bearing Cat No CRCO1OR038HP57 or any approved brand like Havells, Crompton, Vin etc. with 3 years warranty complete as required. The fitting shall be approved by Engineer-in-Charge before executing the work.

Supply and fixing of 15 Watts B22 base LED lamp of approved make having two years warranty

Supply ,installation and testing and commisioning of Schindler 3300IN or equivalent with Gearless & Machine Room less barrier free lift with machine room less and gear less Technology with Automatic rescue device and overload as standard with silent and jerk free ride having effective utilisation of shaft , providing scafolding for installation if any , etc complete testing and as directed and approved by the engineer in charge

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 Laterite aggregate 40 mm . nominal size) excluding cost of centering, shuttering and finishing in all floors

12mm cement plaster 1:3 (1 cement : 3 coarse sand) Extra for providing and mixing water proofing material proportion recommended by the manufacturers.

Ultra-high strength , high -precision, dual shrinkage compensated, free flow cementitious grout for machine , column base plates. Providing and supplying approved which is dual shrinkage-compensated, cementitious grout shall be hydraulic-cement based free-flow, high strength grout that compiles with ASTM C1107. The grout shall have compressive strength minimum of 35 MPa at 1 day and 75 MPa at 28 days; flexure strength minimum of 9 MPa at 28 days. The grout must exhibit positive volumetric expansion in plastic stage as well as hardening stage. Grout must be flowable at 0.15 w/c ratio and shall have fresh wet density in excess of 2200 Kg/m3 . The grout must be accredited by reputed testing institute for dynamic load resistance test of 2 million cycles with no sign of cracking or strength loss. All scaffolding , ladders, supporting materials etc , complete . Rates shall be inclusive of all labour , materials, tools and plants etc. complete.

Demolishing cement concrete 1:3:6 or richer mix including transportation and carriage of materials by loading , unloading and disposal by tipper truck within a lead of 10km and as directed by Engineer incharge etc. complete.

Demolishing R.C.C. work including including transportation and carriage of materials by loading , unloading and disposal by tipper truck within a lead of 10km and as directed by Engineer incharge etc. complete.

Demolishing brick work in cement mortar including transportation and carriage of materials by loading , unloading and disposal by tipper truck within a lead of 10km and as directed by Engineer incharge etc. complete.

Demolishing laterite stone masonry in cement mortar including transportation and carriage of materials by loading , unloading and disposal by tipper truck within a lead of 10km and as directed by Engineer incharge etc. complete.

Dismantling doors, windows and clearestory windows (steel or wood) shutters including chowkhats architrave holdfast etc. complete of area 3 sq.m. and below including transportation and carriage of materials by loading , unloading and disposal by tipper truck within a lead of 10km and as directed by Engineer incharge etc. complete

Dismantling steelwork in single sections in channels, angles, tees and flats including dismembering including transportation and carriage of materials by loading , unloading and disposal by tipper truck within a lead of 10km and as directed by Engineer incharge etc. complete.

Dismantling the tile work in floors and roofs laid in cement for thickness of tiles 10mm to 25mm.including transportation and carriage of materials by loading , unloading and disposal by tipper truck within a lead of 10km and as directed by Engineer incharge etc. complete.

Dismantling asbestos sheet roofing including ridges, hips valley and gutters including transportation and carriage of materials by loading , unloading and disposal by tipper truck within a lead of 10km and as directed by Engineer incharge etc. complete

Dismantling of existing G.I pipe upto 20 mm nominal bore including transportation and carriage of materials by loading , unloading and disposal by tipper truck within a lead of 10km and as directed by Engineer incharge etc. complete

Dismantling as G.I. sheet roofing including ridges, hips valley and gutters including transportation and carriage of materials by loading , unloading and disposal by tipper truck within a lead of 10km and as directed by Engineer incharge etc. complete.

Rates quoted by Contractor for each item should be inclusive of GST