SPECIAL REPAIR FOR JCOs CLUB AND SINGLE ACCN BLDG No P-62 OF FD WKSP EME ENGR BDE AT NASIRABAD

Amount

Taking down cement or cement lime plaster or stone / brick wall, ceiling including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Raking out joints/ pointing to random rubble or polygonal rubble stone masonry uncoursed or brought upto courses built in CM complete all as specified and directed.

M & L for rendering 15mm thick in CM (1:6) on stone masonry surfaces wall finished fair and even complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar (1:4) mixed with water proofing compound @ 3 % by weight of cement on other than fair faces of brick / stone masonary surfaces, finished even and smooth without using extra cement, complete all as specified and directed (WPC measured and paid separately)

M&L for rough cast plaster mix with crusted stone (6-10)mm, sand and cement in the ratio 1:1:1, over 15mm thick cement plaster in cement mortar 1:4 as in under coat including dubbing out (if required) complete all as specified and directed.

M&L for 10mm thick rendering in cement mortar in CM (1:3) on ceiling surfaces finished fair and even complete all as specified and directed.

Dubbing out average 10mm thick in CM 1:4 on irregular faces of walls or concrete chajjas etc complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer over 1 mm thick wall care putty complete all as specified and directed.

M & L for preparation of newly plastered surfaces of walls & applying three coat of white wash complete as specified and directed

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed

M & L for preparation new plastered surfaces of walls and providing two coat of cement base paint over a coat of primer complete all as specified and directed.

M & L for preparation of old plastered or unplastered surfaces of wall including cornices etc applying three coats of white wash complete all as specified and directed.

M & L for preparation of old plastered or unplastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M & L for complete removal of existing treatment of old plastered surface of wall and applying two coats of oil bound distemper over a coat of 1mm thick putty complete all as specified and directed.

Demolition of cement concrete (unreinforced ) in floors and pavings n. exc 15cm thickness (above or below GL) complete all as specified and directed

M&L for machine cut kota sotne slab, 20-25mm thick over and including 15mm thick screed bedding in cement mortar 1:6 as in floors, laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing with mirror polish complete all as specified.

M&L for machine cut kota sotne slab in skirting / steps / risers of reqd size, 20 to 25mm thick & including 15mm thick screed bedding in cement mortar 1:4 as in floors, laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing with mirror polish complete all as specified and directed.

Mirror polishing on existing marble/granite/kota stone/ and stone work where ever required to give high gloss finish complete all as specified and directed.

M&L for 18 to 20mm thick granite ( of any type ) work (table rubbed and polished ) in steps, jambs, pillars, window -cills, cooking platforms and like pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including laid over 15mm thick screed bed in CM (1:6) complete all as specified and directed.

Dismantling of bricks or brick tiles laid in floor dry of pointed complete all as specified and directed.

M&L 75mm thick cement concrete type D-2 1:4:8 (40mm graded stone aggregate ) as in floors / pavings complete all as specified and directed.

M&L for factory made 60mm thick machine pressed precast cement concrete coloured, reflective type interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and pigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & directed.

M&L for providing and laying factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 Cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete, all as specified & directed.

Supply only water proofing compound ISI Marked complete all as specified and directed.

Dismantling floor, hearth or wall tiles, including cement mortar, removing serviceable tiles from site & rubbish off the premises, complete all as specified and directed.

M&L for glazed ceramic coloured tiles 6-7mm thick in vertcial surfaces of size exceeding 0.11 Sqm but not excceding 0.18 Sqm set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick screed plaster in cement mortar 1:4 complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 Sqm but not exc 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedding in cement mortar 1:6 complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.18 Sqm but not exc 0.36 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedding in cement mortar 1:6 complete all as specified and directed.

All as per item No. 28.00 above but in skirting over 10mm thick screeding in cement mortar 1:4 complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate as in floors complete all as specified and directed.

Demolition of brick work or stone masonary built in cement mortar etc complete all as specified and directed.

M&L for walling random rubble masonary uncoursed well bonded bedded and solidly hearted and built in cement mortar 1:6 etc complete all as specified and directed.

All as per sl item No 32.00 here in before but except stones. Note: Old servieable stones retrieved vide Sl item no 31.00 shall be reused.

M & L for brickwork with fly ash bricks, old size, straight or curved on plan exc 6 m mean radius, built in CM 1:6 complete all as specified and directed.

Extra over stone masonary for hammer dressing to face beds and joints maximum depression on face (sand stone) n. exc 20mm depression etc complete all as specified and directed.

M&L for 50mm thick PCC (1:3:6) type C-1 using 20mm graded stone aggregate as in plinth protection finished fair and even laid in alternate bays n.exc 2m in length and joints filled with bitumen mastic 1:3 (1 bitumen :3 sand) complete all as specified and directed.

Supply and fixing toilet paper holder with flat recessed type stainless steel complete all as specified and directed by Engr-in-Charge

S & F in repair for Toilet fittings health faucet complete all as specified and directed. Make :- Jaquar ALD-CHR -573 OR PARRYWARE T9941A1, or make and model are equivalent as approved by GE.

Taking out old unserviceable water closet and S & F Vitreous China wash down closet pan (pedestal pattern), white, including plastic cover white closed pattern whith flat bottom and mild steel chromium plated / PVC hinge device including connections to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe etc complete all as specified and directed.

Taking out old u/s water closet and S&F vitreous China "Orissa pattern" size 580 x 440mm" white, with intergral foot rests with vitreous china 'P' or 'S' trap front or back inlet including connection to trap and to flushing pipe, anti syphnage pipe and making good the floor to match the existing complete all as specified and directed.

S&F in repair PVC valve less, syphonic action type flushing cistern, 10 Litre capacity, low level, white with inlet, ball vlave float, handle including PVC rigid pipe 32mm bore as flush pipe fixed on walls by drilling holes and using PVC rawl plug of suitable size complete all as specified and directed.

S&F in repair PVC connection, heavy duty 15mm bore, 45cm long with 2 Nos PTMT nuts of approved quality complete all as specified and directed.

S&F Soap dish fixed to plugs with chromium plated brass screws embedded in the wall complete, all as specified and directed.

S&F in repair, 15mm bore Brass CP mixer for mixing hot & cold water for wash basin screwed down for iron pipe and fixed complete all as specified.

S&F in repair wash hand basins vitreous china, coloured flat back size 450 x 300mm fixed including bracket, waste pipe and waste coupling complete all as specified and directed.

S&F inrepair tubular towel rail, aluminium anodized, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete all as specified & directed.

S&F stop cock/angle cock 15 mm dia chromium plated fancy type screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete, all as specified and directed.

S&F in repairs 15mm bore cast copper alloy chromium plated fancy type bib tap with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and directed.

S & F brass chromium plated swivel shower rose 125mm size, including fixing to steel pipe or union complete all as specified and as directed by the Engineer-in-Charge

S&F in repair 15mm bore stop valves (concealed) fancy type, chromium plated cast copper alloy,with long shank and cap (Concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions fixed complete all as specified and directed

S&F 1mm thick stainless steel kitchen sink with drainage board with plugs, washers and waste coupling and PVC waste pipe including fixing on half brick wall or cantilever brackets(angle iron ) and connecting union overall size 915mm x 460mm, bowl size 410mm x 330mm x 160mm, fixed in repair, complete all as specified and directed

S&F stainless steel plate rack made of 0.50mm thick of over all size 920mm x 785 mm x 255 mm and weight not less than 7.00 Kg each of approved quality complete all as specified and directed..

Supply and fixing in repairs PVC cabinet of size 450 mm x 600 mm with mirror of good quality with shelves in bath fixed complete to walls complete all as directed by Engineer-in-Charge Make : Prayag Cat No. 555 or eqvt as approved by AO.

Taking down old unserviceable 15mm GI tubing, fittings and connections and removing from site or keeping aside for refixing complete all as specified and directed.

Taking down old unserviceable 20mm GI tubing, fittings and connections and removing from site or keeping aside for refixing complete all as specified and directed.

Taking down old unserviceable 25mm GI tubing, fittings and connections and removing from site or keeping aside for refixing complete all as specified and directed.

S&F 15mm GI water tubing( Concealed type), medium grade, galvanised with all fittings ( and fixed to walls, ceiling or laid in floors/ trenches complete all as specified and directed.

S&F 20mm GI water tubing, medium grade, galvanised with all fittings ( and fixed to walls, ceiling or laid in floors/ trenches complete all as specified and directed.

S&F 25mm GI water tubing, medium grade, galvanised with all fittings ( and fixed to walls, ceiling or laid in floors/ trenches complete all as specified and directed.

Refixing old 15mm GI tubing (Concealed type) galvanised with new fittings and fixed to walls, ceiling or laid in floors, trenches including necessary cleaning, cutting, screwing complete all as specified and directed.

Refixing old 20mm GI tubing galvanised with new fittings and fixed to walls, ceiling or laid in floors, trenches including necessary cleaning, cutting, screwing complete all as specified and directed.

Refixing old 25mm GI tubing galvanised with new fittings and fixed to walls, ceiling or laid in floors, trenches including necessary cleaning, cutting, screwing complete all as specified and directed.

S&F CI Nahani/Floor trap 75 mm outlet,with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4) as in repairs complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n. exc 1.50 sqm each and removing from site complete all as spd & directed and making good disturbed surface of walls in cement mortar (1:3) complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm and n.exc 4.00 Sqm each and removing from site complete and making good disturbed surfaces of wall in CM (1:3) complete all as specified and directed.

S&F Pressed steel door frame of size 105 x 60mm for doors with one or more rebates incl necessary fixing lugs hinges, lock strike plate,hold fasts etc. complete all as specified. The rates include for one shop coat of priming and filling with PCC 1:3:6.

S&F Pressed steel door frame of size 125 x 60mm for doors with one or more rebates incl necessary fixing lugs hinges, lock strike plate, hold fasts etc. complete all as specified. The rates include for one shop coat of priming and filling with PCC 1:3:6.

M&L for rolled mild steel work for stages of water tanks and cooler stand conforming to Fe 290 Gde E-165 complete all as specified and directed.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification & drawing complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing of 30mm thick factory made solid panel PVC door shutter (style) consisting of frame made out of MS tubes for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded. sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement, complete all as specified and directed.

S & F Flush shutters 30mm thick, solid core construction, with block board core and plywood face panels commercial type on both side and both facesis covered with approved pattern with Decorative coloured laminate type 1 of 0.9 mm thick and all around side faces covered with 10mm thick 1st class hard wood liping duly polished complete all as per specified and directed.

Taking down old u/s steel window / ventilator and S & F Steel window/ventilator factory made, out of MS hollow section 79mm x 39mmx1.6mm thick frame with double shutter (glazed & wiregauged shutters) made out of Z section using flush butt welding and tennon riveting all as per IS 1038/83, dobby hinges shall be provided to both shutters, Locking arrangements as per sample approval by GE, provided with knob, 10mm MS square bars in grill, Z section handle 100mm size and 150mm long hook & eye welded to frame and shutter, four Nos lugs welded to frame inculding necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fast and making good in PCC 1:2:4 type B-1 including 02 coats synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and directed. Note : Wire mesh and sheet glass shall be measured & paid separately under respective items.

Dismantling boarding of any description fixed with nails in any position and M&L18/19mm thick block board grade-.II quality, interior grade with decorative type with decorative face veneer on one face fixed complete, including teak wood lipping 19 x 6mm thick fixed with nails in shelves, partition and palmet boxes, shelves, almirah book cases, toilet boxes, racks, cup board shutter and similar works all as spepcified and directed.

S&F continous (Piano) hinges, mild steel, bright finish, width of flaps (when open) 30mm complete all as specified and directed.

S&F hasp & staple 100mm size safety type, aluminium anodised with mild steel hinges pin including bolt of hinge plate & fixed with screws complete all as specified and directed.

S&F 300mm long alumimium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolt of extruded section or cast aluminium alloy all as specified and directed.

S & F extruded aluminium handle fabricated type, anodised 150mm size conforming to IS complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolt of extruded section, ISI marked, 150 mm long complete all as specified and directed.

S&F 300mm ordinary Mild steel rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F 100mm butt hinges extruded aluminium alloy with galvanised mild steel hinge and anodised ISI marked and fixed, complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of apertature 1.40mm and fixed with tinned tacks or stainless steel wire staples all as specified and directed.

S&F Second class HW, plain, solid, straight chowkhats & frames, wrought, framed, rebated on the solid, rounded or chamfered, put together glue pinned at joints complete all as specified and directed.

M&L for preparation of new or previously untreated wood and wood based surfaces of any description not otherwise descriped over 10cm width girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surfaces over 10 cm width or girth & applying two coats of synthetic enamel paint of 1st quality complete all as specified and directed.

S&F 3mm thick sheet glass, ordinary quality, 3mm thick fixed with oil putty size of glass not exc 0.50 sqm in each pane, complete all as specified and directed.

S&F in repairs, 25mm dia stainless steel curtain rod heavy duty with a pair of decorative Curtain Finials/ knob & heavy Curtain Support Bracket for rod made of stainless steel, etc. complete all as specified & directed.

Disconnecting & taking down the existing unserviceable water tank and supply and fix 500 Ltrs capacity rotational moulded polyethylene water storage tanks double layered (Cylindrical vertical with closed top) ISI marked, hoisted and fixed in position and making necessary arrangements for fixing inlet, outlet, over flow pipe & provision of wash out pipe etc. complete as specified in SSR part-I

Disconnecting & taking down the existing unserviceable water tank and supply and fixing 1000 Ltrs capacity rotational moulded polyethylene water storage tanks double layered (Cylindrical vertical with closed top) ISI marked, hoisted and fixed in position and making necessary arrangements for fixing inlet, outlet, over flow pipe & provision of wash out pipe etc. complete as specified in SSR part-I

S&F 20mm ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe of 20mm dia and fixed (minimum weight 210 gms)

S&F in repairs gun metal globe or gate valve, wheel head cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union 25 mm dia, ISI marked complete all as spd & directed.

Taking down 100mm / 75mm dia AC/PVC/CI pipe (any size or pattern ) including all fitting, heads, shoes, bends and removing from sites complete all as specified and directed. (Measured over all as fixed along the centre line over the fittings and accessories)

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber joints fixed to wall or laid in floors / trenches with & including existing / new MS stack clamps of FI 50 x 3mm complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber joints fixed to wall or laid in floors / trenches with & including existing / new MS stack clamps of FI 50 x 3mm complete all as specified and directed.

S&F 110mm PVC (SWR) junction single, (Single T) equal or unequal with access door with cement joint complete all as specified and directed.

S&F 110mm bore PVC (SWR) bend / shoe of any radius with access door, complete all as specified and directed.

S&F 75mm bore PVC (SWR) bend / shoe of any radius with access door, complete all as specified and directed.

S & F 110mm bore PVC (SWR) vent cowl, complete all as specified and directed.

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. or for cable laying or not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/ loose soil complete all as specified and as directed.

Returning and filling in approved earth including levelling spreading watering and well ramming in any layers n. exc 25cm thick complete all as specified and directed.

Removing excavated materials n. exc 100m and depositing where directed and complete all as specified and directed.

M&L cement concrete 1:2:4 using 20mm graded aggregate as in surface channel and drain complete all as specified and directed.

M&L for 150mm dia in bore SGSW drain pipes laid in trenches and jointed complete all as specified and directed.

M & L for PCC 1:2:4 type B2 using 40 mm graded aggregate as in surface channels and drains & coping, edging rounded or chamfered type etc complete all specified and directed

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc.

Disconnecting unserviceable sub main wiring/service connection of any size and including conduit of any type and accessories and removing from site and making good the disturbed surfaces.

Taking down carefully by unscrewing from boards / outlet boxes, fittings and fixtures such as switches, sockets etc for re use at site or carrying to the store(to be measured only when found serviceable in all respects complete for reuse.) complete all as specified and directed

M&L for point wiring with 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed cable in and including PVC rigid non metallic conduit medium grade not less than 20mm dia ISI marked and fittings and accessories concealed in walls/roof/ ceiling with suitable size of sunk type pressed steel modular terminal box and modular white cover plate with frame for suitable module as per site requirements for mounting of modular switches, sockets, fan regulator etc and one green colour cable of 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed as earth wire up to common earth and connected to earth for the following, complete all as specified and directed :-

One light point/bell point controlled by one, one way switch.

One ceiling fan/exhaust fan point controlled by one, one way switch.

One three pin 5 Amp socket on same board with other switches.

One 3 pin 5 Amp socket on independent board.

All as per item No. 108.00 here-in-before but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 2.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth.

S&F modular switch 1 way 6/10Amp , 1 module, complete all as specified and directed.

S&F of modular switch 1 way 16Amp, 1 module, complete all as specified and directed.

S&F of modular socket 6Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F of mdoular socket 16 Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F ceiling rose surface bakelite 3 terminals 63.5 x 17 mm complete all as specified and directed.

Taking down existing exhaust fan & wall mounted fan and re-use at site or carrying to the store(To be measured only when found serviceable in all respects complete for re use.) complete all as specified and directed

S&F of lamp holder PVC/polycarbonate type with back plate complete all as specified and directed.

Supply and fixing LED box type tube light fitting 20 watt made up of CRCA sheet with pre wired double sided connections including 1x20 watt retrofit LED tube rod with extruded aluminium body , PC diffuser and inbuilt driver , double sided connection, complete with all accessories internally prewired complete all as specified and directed.

Supply & fixing ceiling fan 1200 mm sweep , 230 Volts, AC , 50 Hz, copper winded motor, BE star rated white colour complete with motor, blade set of three nos , down rod, canopy, shackle assy complete all as specified and directed.

Supply and fixing wall mounted decorative luminarie fitting suitable up to 9/10 Watt LED lamp champagne gold finish fixture with plastic body suitable for B22 Base complete all as specified and directed by Engr-in-Charge.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete

S&F LED bulk head luminaire 1x 10 W bulk, IP 65 protection complete with all accessories and including connecting up with three core copper conductor cable complete all as specified and directed.

Supply and fixing and testing energy saving street light luminaire 35 watt LED , pressure die cast housing with high power LED as lighting source and lens embedded PC cover with IP 66 protection incl connecting with three core copper flexible wire from ceiling rose to connector of light fitting complete all as specified and directed by Engr-in-Charge.

Supply and fixing recess mounted 2' x 2' LED luminarie 36 watt, cool day/warm light with white powder coated CRCA housing with LED driver, efficiencey >100 Lm/w complete all as specified and directed.

Supply and fixing street light bracket made of 32 mm GI pipe, 1.2 mtr length fixed with two Nos of clamp, nut and bolts complete all as specified and directed.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed multistranded (FRLS) copper conductor cable of size 6.00 Sqmm LT, 1100 volts grade, drawn through and including 25 mm dia or higher PVC non metallic concealed conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistranded copper conductor cable green colour as earth continuity conductor.

M& L for TV Socket including PVC conduit and axial cable wire complete all as specified and directed.

M& L for Telephone socket including PVC conduit and telephone wire complete all as specified and directed.

S & F single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amp MCB SP `C' series for AC complete all as specified and directed.

Taking down and Supply and fixing of Change over Three Pole Neutral AC 63 Amp, with bolted type fuse in sheet enclosure with fuses complete all as specified and directed. Make: Havells Cat No IHKDTW4063 or equivalent.

S&F of MCB distribution board TPN 4 way, 415 volts, double door, with 200 Amps rated bus bar, neutral bar with shrouds, earth bar, IP-43 , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCBs as incomer and outgoing complete all as specified and directed.

S & F of MCB SP, 240 volt, 6 Amp to 30 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S & F of MCB SP, 240 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S & F of MCB SPN, 240 volt, 63 Amp capacity, 10 KA , 'C' curve complete all as specified and directed.

S&F of MCB TPN, 415 volt, 100 Amp capacity,10 KA, 'C' curve complete all as specified and directed.

S&F of MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-42 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing MCB's complete all as specified and directed.

S&F in repairs surface mounted LED downlight 18 watt round shaped, slim surface mounted LED panel with premium diffuser to ensure glare free & even light distribution complete all as specified and directed. Make-: Crompton/Wipro/Philips

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 incl dismantling of old unsv existing earthing complete all as specified and directed.

Supply and laying including jointing, testing or fixing or passing through pipe, trench or duct commissioning and testing XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volt grade size 50 sqmm, 3.5 core complete all as specified and directed by Engineer-in-Charge.

Supply and fixing tubes light grade GI tubing 40 mm dia with all fitting laid in trenches complete all as specified and directed by Engineer-in-Charge.

Supply & spreading in trenches dry river sand cushioning to underground cable in trenches including spreading, levelling hand punning down complete all as specified and directed Note:- Depth of sand cushioning will be measured after punning down and levelling the sand properly.

M & L for laying of bricks locally available sub class 'B' bricks, non-modular sizes as per IS 1077: 1992 for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable all as directed.

M/S SHIVA TRADERS

kirtiman traders

Shree Sai Ram Enterprises

M/S Nexus Projects

M/s AKASH CONSTRUCTION CO.

MAHARANI CONSTRUCTION