Construction of office of Assam Inland Water Transport Regulatory Authority (AIWTRA) and Assam Inland Waterways Company Ltd. (AIWCL) at existing IWT office building at Ulubari, Guwahati-7

Amount

DEMOLITION WORKS

Demolition of exsisting all Assam Type infrastructure in side the premises of DIWT, Paver blocks, Drains, Water Tanks, Pump house, septic tanks, etc and stack all the dismantle materials with stack.

SITE CLEARANCE

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. Beyond 30 cm girth upto and including 60 cm girth: Shrubs

Beyond 120 cm girth upto and including 240 cm girth: Trees

REPAIR WORKS

Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer In-Charge. With cement mortar 1:4 (1cement: 4 coarse sand)

Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer in-Charge Door chowkhats

Window chowkhats

Clerestory window chowkhats

Fixing chowkhat in existing opening in brick/ RCC wall with dash fasteners/Chemical fasteners of appropriate size (3 nos on each vertical member of door chowkhat and 2 nos on each vertical member of window chowkhats), including Cost of dash fasteners/ chemical fastener

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm)

Renewing glass panes, with wooden fillets wherever necessary:… Float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm)

Renewing bottom rail and/or top runner of collapsible gate including making good all damages and applying priming coat of zinc chromate yellow primer of approved brand and manufacturer

Providing and fixing 85x42 mm chromium plated brass pull bolt lock with necessary chromium plated brass screws, nuts, bolts and washers etc. complete

Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in charge.

Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in-charge

Providing & fixing White vitreous china water closet squatting pan (Indian type) along with "S" or "P" trap including dismantling of old WC seat and "S" or "P" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge.Orissa pattern W.C Pan of size 580x440 mm

Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer in Charge

Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer in-Charge (a) Internal Work- Exposed on wall

CIVIL CONSTRUCTION

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Kiln seasoned and chemically treated hollock wood

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On concrete work

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides

20 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 1.00 mm thick with zinc coating not less than 275 gm/m²

0.80 mm thick with zinc coating not less than 275 gm/m²

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete: Ridges plain (500 - 600mm)

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sq

Providing and applying two coats of fire retardant paint on cleaned wood / ply surface @ 3.5 sqm per litre per coat including preparation of base surface as per recommendations of manufacturer to make the surface fire retardant

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand)

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.

Providing and Fixing factory made uPVC door frame, made of uPVC exturded sections, of size 65 mm x 55 mm with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm (±0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer's specification and direction of Engineer-in-charge.

Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately). 18 mm thick

Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with : Decorative veneer facings of approved manufacture

Providing and laying Gypsum panel partitions 100 mm thick with water proof Gypsum panels of size 666x500x100 mm, made of calcite phosphor Gypsum fixed with tongue and groove, jointed with bonding plaster as per manufacturer’s specifications in superstructure above plinth level up to floor V level. Gypsum blocks will have a minimum compressive strength of 9.3 kg/cm2

Non-Schedule Supplying, fitting and fixing MAC blinds horizontal and vertical complete as specified and directed by the department at all levels. Horizontal Blinds Reference: The carino Range, Fiona Mushroom

Roller Blinds Make: JOHNSON or equiv: Roller Blinds with Decorative cassate Quality : sun screen , colour : SSR'2

No allowances shall be made to undertake rectification works if the same are so desired to be undertaken for improper adherance to recommended application procedures / standards. All joints, where ever necessary, shall be undertaken after prior approval of the same from the Architects. All finished flooring surfaces shall be free from bubbles/scratches/ stains/etc. prior to final hand- over of the activity at the desired locations. All material utilised shall be as per tender recommendations and shall be applied according to manufacturer's specifications. The rate shall be inclusive of heavy duty plastic sheet (2 layers) to protect the flooring till instructed to remove the same by the PMC/architect. Providing & laying carpet tiles of 5mm thickness as per manufacturer's specifications. Design: Sterling blue- 6984, Melody 6, Make Heritage or eqv

Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete.

SANITARY

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 453x357 mm

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS :2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms

Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. Rocky strata including Boulders 350 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge 150 mm nominal dia Pipes

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Form Work- Suspended floors, roofs, landings, balconies and access platform

WATER SUPPLY

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 40 mm nominal outer dia Pipes

BRASS FITTINGS

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

C.P. BRASS FITTINGS

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore

Providing and fixing PTMT grating of approved quality and colour. rectangular type with openable circular lid 150 mm nominal size square 100 mm diameter of the inner hinged round grating

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

PARKING

Surface dressing of the ground including removing vegetation and in equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift up to 1.5 m. All kinds of soil

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge All kinds of soil

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25

Paver: Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density

Paver: Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all asper direction of Engineer-in-Charge 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern

DRAINAGE

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width aswell as 10 sqm on plan) including getting out and disposal of excavatedearth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soil

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete Concrete of M30 grade with minimum cement content of 350 kg /cum

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 12 mm cement plaster

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

HORTICULTURE WORKS

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.

Providing and stacking of Washingtonia filifea palm stem ht. 120-135 cm with 8-10 healthy leaves lush green leaves well developed in big size HDPE Bags as per direction of the officerin-charge.

Providing and stacking of Washingtonia filifea palm stem ht. 90-105 cm with 6-7 healthy leaves lush green leaves well developed in big size HDPE Bags as per direction of the officer-incharge.

Providing and stacking of Terminalia arjuna of height 150-165 cm. in big polybags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Tectona grandis (Teak) of height 150-165 cm. in big polybags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Fishtail palm of ht. 210-240 cm bottom girth 25-30 cm well developed in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Fishtail palm of ht. 270-300 cm bottom girth 40-50 cm well developed in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Foxtail palm of ht. 120-150 cm bottom girth 15-20 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Tecoma stans of height 90-105 cm. bushy in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Thuja compacta of height 75-90 cm., conical shaped, well formed with healthy foliage in earthen pots of size 30 cm as per direction of the officer-in-charge.

Providing and stacking of Tecoma gaudichaudi of height 90-105 cm.,bushy in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Tabernaemontana coronaria (Chandni single) variegated of height 105-120 cm., multibranched, bushy in big size HDPE bag as per direction of the officer-incharge.

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately).

Providing and Displaying Dahlia double kenya variety in different colour well developed with 3 to 4 flowers in half bloom, good foliage stacked with Green painted Bamboo sticks, 45 to 60 cm height in 25 cm Earthen Pot/ Plastic Pot and as per direction of the officer-in-charge.

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unsaverieable material’s as per direction of officer in charge (excluding cost of plant & water)

Supply and installation of Biowall panels at site, plant material, soil mixture, and installation of drip irrigation system. Biowall panel by drilling and fixing the frame directly into wall by instaling on MS iron fabrication. A list of recommended biowall plants to be provided by vendor after considering site weather,temperature, humidity, sun light, heat absorbed or reflected by nearby surfaces such as stone or glass panels, water quality and approved by consultant. Performance guarantee that biowall installation for a period of 3 months after handover for any defect in installation or drip irrigation. 20% of the total plant quantities which are lost or damaged will be replaced during guarantee period.

Providing and fixing M.S. flat iron tree guard 60 cm dia and 2 m high, above ground consisting 4 nos 25 x 6 mm, 2.25 m long and 8 nos 25 x 3 mm 2 m long verticals M.S. flats, riveted to 3 nos 25 x 6 mm M.S. flat iron rings in two halves, fixing together at site with required six numbers of 8 mm dia and 30 mm long bolts, including painting two coats with synthetic enamel paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be suitably fixed to the ground by embedding four legs of tree guard in pits of suitable dia and to a depth of 25 cm, refilling the pits with soil and ramming, complete in all respect as per satisfaction and direction of Officer-in-charge

INTERIOR

Providing and fixing colored Text as per approved design of 12mm thick MDF partitions as per detail and instructions of the architect.Cost to include cutting design & installation, designing and samples , drafts for client approvals all complete as per design detail Make - As per technical specs

Frosted Film - FR - monochrome design printed and laser cut pattern - Providing and fixing frosted film on Glass Partition with MCS warranty of 5 years as per the manufacturer specification. (Finished works to be measured as smt). To include cost of printing & designing, samples and drafts approvals. HEIGHT OF FROST FILM ASSUMED 1.2M - On glass surfaces / Frosted Color Printed Graphic - Providing and fixing colored graphics as per approved design of 3M film over glass partitions as per detail and instructions

Notice Boards - Providing & placing readymade notice boards of approx size 1500x 600 with metal backing covered with fire retardant fabric (basic rate: 200/sft) having an aluminium frame, fixed at locations indicated. Rate to also include accessories such as magnets etc.

Signage: Providing and fixing signages for meeting rooms, toilets, pantry doors, ALL RELEVANT AS PER INSTRUCTIONS etc.in brushed steel plate with embossed signage. Plate size of 150mm x 300mm with text of approved style and font as per instructions of the architect. Fixing on glass doors with 3M adhesive tape and on solid doors with mirror screws.

BACKDROP LOGO AS PER CLIENT DESIGN: Providing and fixing main signages in reception ALL RELEVANT AS PER INSTRUCTIONS etc in 25mm thk. Acrylic Backlit/ Corian finish with text of approved style and font as per instructions of the architect with light. - ON RECEPTION back drop - SIZE 750 *2000mm

Transition Profiles (Floor): Providing and fixing pre-approved bought out transition profiles of SS for joints on the floor between flooring of two different materials. The transition profile to have flanges to overlap over both the materials on either side as per sample approved by the architect. Approx width of 32 mm. PREFERRED SOLID straight SS strip 8-10mm thk, height as per fixing detail . Approved make: Bottom line or equivalent

Dustbins: P/F MS powder coated dustbins for Workspace & meeting rooms (250mm widex350-400mm tall). Assumed 1 per cluster,cabin, meeting room

P/F Plastic heavyduty dustbins with lids for Dishwash & kitchen (600mm dia x1200mm high approx)

P/F MS powder coated dustbins with lids & Peddle for Washrooms (250mm widex350-400mm tall)

Kitchen Equipment: Microwave Oven - 20ltr

Kitchen Equipment: : Coffee Vending machine

Providing & supplying - 3+1 seater sofa with Fabric / Leatheritte Finish. Seat Height between 425-475mm, Back support as per design. - Specs: Steel frame with zigzag springs. Seat cushions: cold cure foam sandwich construction with an outer layer of wadding. Back cushion: ticking sewn into chambers with latex rod/fibre filling. Legs: inverted skid base in aluminium-powder coated black gloss" - Size: Regular 2 seater sofa in semi-circular pattern (Refer layout)"

Single Seater Sofa: Providing & supplying - single seater sofa with Fabric / Leatheritte Finish. Seat Height between 425-475mm, Back support as per design. Specs : All upholstered elements to contain dimensionally stable polyurethane foam padding, Recessed Back Rest and cushions: Back Rests 600 x 360mm (450 x 360 mm optional side arm rests). Frame: Powder-coated steel,dark grey with plastic glides

PRINTER TABLE - SIZE- 1050W X 600D X 750HT - Specifications: Table top - 25mm thick Pre-laminated particle board finished with 2mm PVC edge lipping. Under Structure - Leg constructed by MS powder coated using high pressure die casting connectors, Dia 44.50 ERW Tube – 16g, clear & tough polycarbonate leg bush & swivel type levellers, aluminium die cast connectors and supporting 40 x 20 Manger Cap Per Wks. include wire entry cover mm MS cross beams. The legs shall have no visible hardware, and its transparent and self-adjusting shoes gives the table a light, almost floating look. High pressure aluminium die- casting and weld less technology to be used to maintain consistent and smooth aesthetic look. Wire Management - 70mm thick, 250mm HT Raceway with metal facia on main spine BTT & 65mm Wire

WORSKSTATIONS - P/F desking type Workstation with adequate supporting mechanism in configuration of clusters as/dwg, comprising of the following components: Central Structural Column with access facility and supporting legs (as suggested by vendor) between every 2 workstations with complete wire management capabilities and metal cable riser. The workstations are arranged in continuous rows of Workstations as per layout. - Size: 1200 x 600 x 750 HT table top with 350 ht screens - Table top - 25mm thick Pre-laminated particle board finished with 2mm PVC edge lipping. Main Screen: 12 mm Fabric magnetic tiles of 350HT in the workstation. 08nos magnets to be provided for each workstation. Under Structure - Leg constructed by MS powder coated using high pressure die casting connectors, Dia 44.50 ERW Tube – 16g, clear & tough polycarbonate leg bush & swivel type levellers, aluminium die cast connectors and supporting 40 x 20 mm MS cross beams. The legs shall have no visible hardware, and its transparent and self-adjusting shoes gives the table a light, almost floating look. High pressure aluminium die- casting and weld less technology to be used to maintain consistent and smooth aesthetic look. - Wire Management - 70mm thick, 250mm HT Raceway with metal facia on main spine BTT & 65mm Wire Manger Cap Per Wks. include wire entry cover - MOBILE PEDESTAL 2D+1F: SIZE: 400W x 450D x 640HT Pedestal : Pedestal are made of 18mm thick PLB with 2 drawer units and 1 filling folder unit. The Drawer units are made mobile with the use of castors. The drawer units are provided reccessed handle and suitable locks. CPU Trolley

CABIN TABLE - MAIN TABLE: 2400W X 900 D X 750HT WITH - EXTENDED SEMICIRCLE TABLE - SIDE TABLE: 1500 W X 450D X 750 HT - BACK STORAGE: 1200 W X 450D X 750 HT- 2 no -Specification: -Table top : 25mm thick Pre-laminate particle board finished with 2mm edge lipping. - Under Structure - Leg constructed by MS powder coated using high pressure die casting connectors, Dia 44.50 ERW Tube – 16g, clear & tough polycarbonate leg bush & swivel type levellers, aluminium die cast connectors and supporting 40 x 20 mm MS cross beams & 18mm thick Plt modesty panel. The legs shall have no visible hardware, and its transparent and self-adjusting shoes gives the table a light, almost floating look. High pressure aluminium die- casting and weld less technology to be used to maintain consistent and smooth aesthetic look. Back Storage: Storage is made of 18mm PLB with Openable shutters, adjustable shelves, locking mechanism and recessed handles. - Wire management: One no Flip up 300 with provision for Switch cut out are provided for power and data cable management. - MOBILE PEDESTAL 2D+1F - SIZE: 400W x 450D x 640HT - Pedestal: Pedestal are made of 18mm thick PLB with 2 drawer units and 1 filling folder unit. The Drawer units are made mobile with the use of castors. The drawer units are provided recessed handle and suitable locks. - CPU Trolley and Keyboard Tray

CONFERENCE TABLE Specification: Size: 3600 x 1200 x 750 mm ht Table top: 25mm thick Pre-laminate particle board finished with 2mm edge lipping. Under Structure - Leg constructed by MS powder coated using high pressure die casting connectors, Dia 44.50 ERW Tube – 16g, clear & tough polycarbonate leg bush & swivel type levellers, aluminium die cast connectors and supporting 40 x 20 mm MS cross beams. The legs shall have no visible hardware, and its transparent and self-adjusting shoes gives the table a light, almost floating look. High pressure aluminium die- casting and weld less technology to be used to maintain consistent and smooth aesthetic look. Wire management: Two Nos Flip up 300 with provision for Switch cut out are provided for power and data cable management.

STORAGE: Specification: Storage : Storage is made of 18mm PLB with openable shutters, adjustable shelves, auto closing hinges, locking mechanism and recessed handles. - Size: 1200 x 450 x 1200 HT

STORAGE: Specification: Storage : Storage is made of 18mm PLB with openable shutters, adjustable shelves, auto closing hinges, locking mechanism and recessed handles. - Size: 1050 x 450 x 1200 HT

STORAGE: Specification: Storage : Storage is made of 18mm PLB with openable shutters, adjustable shelves, auto closing hinges, locking mechanism and recessed handles. - Size: 900 x 450 x 1200 HT

RECEPTION TABLE - Specification: - Size: 2000 x 1200 x 750 mm ht - Table top: 25mm thick Pre-laminate particle board finished with 2mm edge lipping. - Under Structure - Leg constructed by MS powder coated using high pressure die casting connectors, Dia 44.50 ERW Tube – 16g, clear & tough polycarbonate leg bush & swivel type levelers, aluminium die cast connectors and supporting 40 x 20 mm MS cross beams. The legs shall have no visible hardware, and its transparent and self-adjusting shoes gives the table a light, almost floating look. High pressure aluminium die- casting and weld less technology to be used to maintain consistent and smooth aesthetic look. - Wire management: Two Nos Flip up 300 with provision for Switch cut out are provided for power and data cable management.

Semi-Executive Chair Leatherette, Ash Grey Size: 76 CM x 98.5 - 108.5 CM x 76 CM

Executive Chair: Prime High Back Chair Knitted Fabric, Black Ink Size: 76.1 CM x 114 - 128 CM x 76.1 CM

Motion High Back Chair Adjustable Armrest, Royal Blue With White Body Size: 76 CM x 98.5 - 108.5 CM x 76 CM

Task Chair Mid Back Comfortable Fabric Office Executive Chair Mesh Office Arm Chair

Visitor Chair

ROUND DISCUSSION TABLE Size: 900 Dia x 750Ht Table Top: 25mm plb with 2mm edge bending Powder coated Pronge legs

MEETING TABLE Size: 1800 x 1050 x 750 mm ht. Specification: Table top: 25mm thick Pre-laminate particle board finished with 2mm edge lipping. Under Structure - Leg constructed by MS powder coated using high pressure die casting connectors, Dia 44.50 ERW Tube – 16g, clear & tough polycarbonate leg bush & swivel type levellers, aluminium die cast connectors and supporting 40 x 20 mm MS cross beams. The legs shall have no visible hardware, and its transparent and self-adjusting shoes gives the table a light, almost floating look. High pressure aluminium die- casting and weld less technology to be used to maintain consistent and smooth aesthetic look.

CABIN TABLE MAIN TABLE: 1500W X 750D X 750HT SIDE TABLE: 1050 W X 450D X 750 HT Specification: Table top: 25mm thick Pre-laminate particle board finished with 2mm edge lipping. Under Structure - Leg constructed by MS powder coated using high pressure die casting connectors, Dia 44.50 ERW Tube – 16g, clear & tough polycarbonate leg bush & swivel type levellers, aluminium die cast connectors and supporting 40 x 20 mm MS cross beams & 18mm thick Plt modesty panel. The legs shall have no visible hardware, and its transparent and self-adjusting shoes gives the table a light, almost floating look. High pressure aluminium die- casting and weld less technology to be used to maintain consistent and smooth aesthetic look. Wire management: One no Flip up 300 with provision for Switch cut out are provided for power and data cable management. MOBILE PEDESTAL 2D+1F SIZE: 400W x 450D x 640HT Pedestal: Pedestal are made of 18mm thick PLB with 2 drawer units and 1 filling folder unit. The Drawer units are made mobile with the use of castors. The drawer units are provided recessed handle and suitable locks. CPU Trolley and Keyboard Tray

Door Knobs: Cylindrical Lock Material: Brass, Finish: Bronze

Door Stopper (fixed to wall): Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete

Door Stopper (fixed to door)Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

ELECTRICAL

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 10 sq. mm + 1 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing following pair 0.5 sq mm FR PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 1 pair

Supplying and drawing following pair 0.5 sq mm FR PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 pair

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/recessed steel/ PVC conduit as required

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Supplying and fixing metal box of following sizes (normal) on surface or recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 100 mm x 100 mm x 60 mm deep

Supplying and fixing metal box of following sizes (normal) on surface or recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 180 mm x 100 mm x 60 mm deep

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 A socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 A socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. TV antena socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Bell push

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1or2 Module (75mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 3 Module (100mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 6 Module (200mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 8 Module (125mmX125mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing call bell / buzzer suitable for DC/AC single phase, 230 volts complete as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 3 nos. 3 pin 5/6 A modular socket outlet and 3 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings). [SOC}

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required. [Pa/c]

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way, Double door

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 16 way, Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 amps

Supplying and Fixing Singe Pole Blanking Plate in the existing MCB DB complete etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4 + 24), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB/MCCBs (but without MCCB/MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 4 way (4 + 12), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB/MCCBs (but without MCCB/MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and Fixing Singe Pole Blanking Plate in the existing MCB DB complete etc. as required.

Supplying and fixing DP sheet steel enclosure on surface! recess along with 25/32 A 240 V "C“ curve DP MCB complete with connections, testing and commissioning etc. as required.

Supplying and fixing TP sheet steel enclosure on surface/ recess along with 16/25/32 A 415 V "C" curve TP MCB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc.as required. For 4 way, Double door TPN MCBDB

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc.as required. For 8 way, Double door TPN MCBDB

Providing and fixing M.V.danger notice plate of 200 mm x 150 mm,made of mild steel at least 2 mm thick and vitreous enamelled white on both side and with inscription in single red colour on front side as required.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 Metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 4mm dia.copper wire on surface or in recess for loop earthing as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, copper tube, having single prong at top, with 85 mm dia 3 mm thick copper base plate including holes etc. complete as required.

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick copper strip, 125 mm long, with 4 nos. of tinned brass bolts, nuts, chuck nuts and spring washers etc. complete as required.

MV CABLE JOINTING & END TERMINATION: Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 25 sq. mm (28mm)

MV CABLE JOINTING & END TERMINATION: Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 70 sq. mm (38mm)

MV CABLE JOINTING & END TERMINATION: Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 185 sq. mm (57mm)

HVAC(ONLY PLUMBING,DUCTING & AHUs)

PLUMBING INSULATED CHILLED WATER PIPING (resin bonded fiber glass glass INSULATION) Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with 80 kg/cum density resin bonded fiber glass or 144 Kg/ cu m density mineral wool (non Combustible) pipe section insulation 150mm dia. (50mm thick insulation)

PLUMBING INSULATED CHILLED WATER PIPING (resin bonded fiber glass glass INSULATION) Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with 80 kg/cum density resin bonded fiber glass or 144 Kg/ cu m density mineral wool (non Combustible) pipe section insulation 50mm dia.(50mm thick insulation)

PLUMBING INSULATED CHILLED WATER PIPING (resin bonded fiber glass glass INSULATION) Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with 80 kg/cum density resin bonded fiber glass or 144 Kg/ cu m density mineral wool (non Combustible) pipe section insulation 25 mm dia (50mm thick insulation)

INSULATED CHILLED WATER PIPING (Nitrile rubber insulation) 40mm dia. (32 mm thick insulation)

INSULATED CHILLED WATER PIPING (expanded polystrene insulation) Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping plumbing inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with fire retardant quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500g polythene faced hessain and finally applying 0.63mm aluminium sheet cladding complete with type3 , grade 1 roofing feltstrip(as per IS:1322 as amended up to date ) at joints repairing of damage to building etc. as per specifications and as required complete in all respect. 25 mm dia (50mm thick insulation)

INSULATION ON EXISTING PIPE: Supplying, laying/ fixing, testing and commissioning of following thickness resin bonded fiber glass pipe section insulation having 40mm

INSULATION ON EXISTING PIPE: Supplying, laying/ fixing, testing and commissioning of following thickness resin bonded fiber glass pipe section insulation having 25mm

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/hot eater circulation as specified 150mm dia.

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/hot eater circulation as specified 40mm dia.

BALANCING VALVE WITH BUILT IN MEASURING FACILITY with C I body flanged construction with EPDM coated disc with long pitch with protected out pipe insulation & PN 16 pressure rating for chilled / hot water circulation as specified. 150mm dia.

BALANCING VALVE WITH BUILT IN MEASURING FACILITY with C I body flanged construction with EPDM coated disc with long pitch with protected out pipe insulation & PN 16 pressure rating for chilled / hot water circulation as specified. 40 mm dia

NON - RETURN VALVE with duel plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating for chilled / hot water circulation including insulation as specified. 150mm dia.

NON - RETURN VALVE with duel plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating for chilled / hot water circulation including insulation as specified. 65 mm dia

Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified. 150mm dia.

Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified. 65mm dia.

Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required

Providing & fixing in position the mercury in glass industrial type thermometers.

FIRE DETECTION AND ALARM SYSTEM (CONVENTIONAL)

Supplying, installation, testing & commissioning of heat detector operating at 54ºC/57ºC with rate of rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection etc. as required.

Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required.

Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

ASPIRATION DETECTOR ACCESSORIES Supply, installation, testing and commissioning of 25 mm Outer dia CPVC PIPE with end caps including making air sampling opening of appropriate dia on appropriate interval and all accessories as required,(rate for area protected in sqm).

INTELLIGENT FIRE ALARM SYSTEM

Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supply of following size of PVC/XLPE insulated and PVC sheathed 11 KV grade aluminium conductor LT armoured UG cable complete handling to proper place as speciefied and directed by the deptt. 25.00 mm² 3½ core U.G. Cable

Supply of following size of PVC/XLPE insulated and PVC sheathed 11 KV grade aluminium conductor LT armoured UG cable complete handling to proper place as speciefied and directed by the deptt. 70.00 mm² 3½ core U.G. Cable

Supply of following size of PVC/XLPE insulated and PVC sheathed 11 KV grade aluminium conductor LT armoured UG cable complete handling to proper place as speciefied and directed by the deptt. 185.00 sqmm 31/2 core UG cable

Supplying and fixing of Fan box (AKG or equivalent as approved by the Deptt.) with inbuild rod as required.

DATA CABLING AND FIXURES Supply, installation testing and commissioning of following LAN networks equipments.

Patch Cord Cat 6 UTP Gray 1m - Moulded SCHNEIDER/ LEGRAND or equivalent

Patch Cord Cat 6 UTP Gray 2m - Moulded SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..

Patch Panel Cat 6 UTP Keystone -24 Port- Loaded SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..

Patch Panel Cat 6 UTP Keystone -48 Port- Loaded SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..

APW Flexi box Wall mount Rack 12U 600 X 550mmD Networking Wall mount Rack with Front Tinted Glass Door with Lock "PDU 6*5A - 01 Nos.Fan 90 cfm 230V - 01 Nos. Mounting Hardware (Set of 10) - 1 Set 19"" 1U Cable Manager - 1 Nos."

APW Cyber Rack Server Rack 42U APW President Enclosure, 600mm W CYBERACK 42U / 1000mm D (CRCA Steel Frame with Aluminium Profiles & 2 Nos. of Removable Side Panels with following items: - Top cover with cable entry -1no. - Bottom cover with cable entry -1no. - 19” Mounting Angles – 2 pairs. ,Finish : Powder coated to 80 microns; Matt finish. colour : BLACK with , Load rating capacity -- 500 kgs., Front side vented glass door and rear full perforated steel door with locks. "PDU 10*5/15A - 01 NosFan Housing Unit with 4 Fans - 01 SetMounting Hardware (Set of 20) - 1 SetCastor with Brake - 2 Nos.Castor without Brake - 2 Nos.Earthing Kit - 01 Set"

Supplying with fitting and fixing of CAT 6 RJ-45 Computer jack in one module MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department.

UPS: Supplying including installation of Inverter (NUMERIC/ Microtech/ V-Guard/ Luminous) with Battery and its case as per direction and specified by the Deptt. 30 KVA On-Line UPS System (Orion or equivalent make as approved by the Deptt.) with PWM-IGBT technology 240V DC Input (300V – 470V A 3 Ph input- 3 Ph output with Isolation Transformer24KW output with 0.8 output PF30 min backup using SMF battery

LIGHTING FITTING & FIXURES

Supplying of the following indoor Decorative Recess mounted LED down lighter luminaries of nake-JAQUAR model no-LESPO1R009XC 9W LED complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Jaquar / LT / Wipro make). [CL]

Supplying of Indoor Decorative Recess mounted LED down lighter luminaries of make-JAQUAR model no-LARP01RO12XN (AREVA PRIME) 12W LED complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Jaquar / LT / Wipro make). [DL]

Supplying of Indoor Decorative Recessed mounted 2' x 2' LED down lighter luminaries of Make-JAQUAR model no- LULTU1S036XC 36WATT complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department. [CLS]

Supplying of Indoor Decorative Surface mounted LED down lighter luminaries of Make-JAQUAR model no- LGLZ01X01XC 10WATT complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department . [ML]

Supplying and fixing of 400 mm sweep Wall fan of make ORIENT Cat/Brand TornadoWall-50 Wall Fan of colour White, Brown or Bianco complete with down rod or equivalent etc. [WF]

Supplying of 300 mm sweep exhaust fan of make BAJAJ Cat/Brand Freshee300mm complete with all accessories complete or equivalent. [EF]

MCB AND MCCB

Supplying and fixing following rating, Single pole, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing following rating, Double pole, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing following rating, Three pole, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps

Supplying and fixing following rating, four pole, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing following rating, four pole, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 63 A, 25KA, FP MCCB

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 100 A, 25KA, FP MCCB

Supply, Installation antistatic rubber mat suitable for 1.1 KV Voltage grade

Supplying ,installation, testing & commissioning of Distribution Box 20 pairs with Krones ( SIEMENS or equivalent as approved by the Deptt.)

Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required. Above 4.5 metre and upto 6.5 metre

Supplying and fixing of 32 mm dia X 2.00 metres long G.I. pipe (medium class) bracket for mounting of fluorescent / HPMV / HPSV street light fitting on pole including bending the pipe to the required shape, 2 nos 40 mm X 3 mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint etc. as required.

Non Schedule Supplying of the following indoor Decorative Recess mounted LED down lighter luminaries of nake-JAQUAR model no-LESPO1R009XC 9W LED complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Jaquar / LT / Wipro make). [CL]

Non Schedule Supplying of Indoor Decorative Recessed mounted 2' x 2' LED down lighter luminaries of Make-JAQUAR model no- LULTU1S036XC 36WATT complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department. [CLS]

Non schedule Water proof square shape 5W LED modern acrylic outdoor and indoor garden wall lamp fixture (Warm White)

Construction of 250KVA 11/0.430 Kv substation with construction of 500 m odf single circuit 11kv OH line with ACSR "RACOON" conductor on steel tubular pole SP-56 (with avaregar span 35 m) with feeder pillar alonwith PROVISION FOR SECURITY DEPOSIT AND SUPERVISION CHARGES FOR APDCL

250 KVA DIESEL GENERATOR SET: Supplying including installation, testing and comissioning of water cool green diesel generator set coupled to suitable alternator of 450 Volt, AC,3-phase0.8p.f.(LA mounted on a 1) M.S fabricated base frame., 2M.S. fuel tank of required capacity.,3(residual silencer., 4(AMF/standard control panel). 5(suitable batteries with lid., 6 first fill of lube oil., 7 acoustic encloser complete with all accessories as specified and directed by the department confirming to IS comprising the following Technical Specifications (Range from 15KVA to 625 KV technical data generator set specifications 250/200 3 no of phases 3 phase ,4. power factor 0.8 LAG Jackson Engine specifications. 1) No. of Cylinders 6 2) Aspirations. Turbo Charged Air cooled. 3) Cooling. Water cooled 4) Governor electronic 5) Battery capacity rating. 2x12 Volt 6) Fuel Consumption LTR/HR@ 75% load 40.8 Alternator Specification 1) Voltage regulation.+/-1.0% 2) Insulation. class_H 3) Standard Enclosure.IP23 4) No. of phases 3 with AMF control panel.

Supplying with installation testing and commissioning of Hi -- wall 5 STAR rating non ducted split type air conditioner of the following capacity with cordless remote complete with indoor and outdoor unit, copper pipe and electrical connection as approved by the Deptt.)up to 5 m between the room unit and out door unit as directed by the department. 1.5 Ton capacity with Copper Condenser. (Make:-Voltas Cat. No. White 185vSzs, Copper Condenser )

Supplying with fitting and fixing Voltage stabilizer of the following specification complete including making necessary connection as approved, specified and directed by the deptt. (SKYLAND / Vee-Dee / V GUARD / VERTEX/ INDO/ VENUS make) 4.0 KVA Automatic Input 90-280 V Out put 200-240 V

PEEYUSH BAHETI

M/s Mechfab Engineering Industries Pvt.Ltd

M/s R.D.Constructions

shivam sharma

VERSHA TECHNOTRADE PVT LTD

golden traders

Bidder Name

shivam sharma